NLAS324 Dual SPST Analog Switch, Low Voltage, Single Supply The NLAS324 is a dual SPST (Single Pole, Single Throw) switch, similar to 1/2 a standard 4066. The device permits the independent selection of 2 analog/digital signals. Available in the Ultra-Small 8 package. The use of advanced 0.6 CMOS process, improves the RON resistance considerably compared to older higher voltage technologies. • • • • • • • • • • • • On Resistance is 20 Typical at 5.0 V Matching is < 1 Between Sections 2 - 6 V Operating Range Ultra Low < 5 pC Charge Injection Ultra Low Leakage < 1 nA at 5.0 V, 25°C Wide Bandwidth > 200 MHz, -3 dB CMOS/TTL Compatible 2000 V ESD (HBM) Ron Flatness 6 at 5.0 V US8 Package Negative Enable Switches are Independent http://onsemi.com MARKING DIAGRAM 8 8 1 US8 US SUFFIX CASE 493 COM1 IN2 1 7 3 1 PIN ASSIGNMENT 8 2 D L7 = Device Code D = Date Code NC1 1 NC1 L7 6 VCC IN1 2 COM1 3 IN2 4 GND 5 NC2 6 COM2 7 IN1 8 VCC COM2 FUNCTION TABLE GND 4 5 NC2 Figure 1. Pinout On/Off Enable Input State of Analog Switch L H On Off ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 9 of this data sheet. Semiconductor Components Industries, LLC, 2003 January, 2003 - Rev. 3 1 Publication Order Number: NLAS324/D NLAS324 MAXIMUM RATINGS Symbol Parameter Value Unit VCC DC Supply Voltage 0.5 to 7.0 V VI DC Input Voltage 0.5 to 7.0 V VO DC Output Voltage 0.5 to 7.0 V IIK DC Input Diode Current VI < GND 50 mA IOK DC Output Diode Current VO < GND 50 mA IO DC Output Sink Current 50 mA ICC DC Supply Current per Supply Pin 100 mA IGND DC Ground Current per Ground Pin 100 mA TSTG Storage Temperature Range 65 to 150 C TL Lead Temperature, 1 mm from Case for 10 Seconds TJ Junction Temperature under Bias JA Thermal Resistance PD Power Dissipation in Still Air at 85C MSL Moisture Sensitivity FR Flammability Rating VESD ESD Withstand Voltage (Note 1) 260 C 150 C 250 C/W 250 mW Level 1 Oxygen Index: 28 to 34 UL 94 V-0 @ 0.125 in Human Body Model (Note 2) Machine Model (Note 3) Charged Device Model (Note 4) > 2000 > 150 N/A V Maximum Ratings are those values beyond which damage to the device may occur. Exposure to these conditions or conditions beyond those indicated may adversely affect device reliability. Functional operation under absolute maximum-rated conditions is not implied. Functional operation should be restricted to the Recommended Operating Conditions. 1. Measured with minimum pad spacing on an FR4 board, using 10 mm-by-1 inch, 2-ounce copper trace with no air flow. 2. Tested to EIA/JESD22-A114-A. 3. Tested to EIA/JESD22-A115-A. 4. Tested to JESD22-C101-A. RECOMMENDED OPERATING CONDITIONS Symbol Characteristics Min Max Unit VCC Positive DC Supply Voltage 2.0 5.5 V VIN Digital Input Voltage (Enable) GND 5.5 V VIO Static or Dynamic Voltage Across an Off Switch GND VCC V VIS Analog Input Voltage (NO, COM) GND VCC V TA Operating Temperature Range, All Package Types -55 +125 °C tr, tf Input Rise or Fall Time, (Enable Input) 0 0 100 20 ns/V Vcc = 3.3 V + 0.3 V Vcc = 5.0 V + 0.5 V 90 419,300 47.9 100 178,700 20.4 110 79,600 9.4 120 37,000 4.2 130 17,800 2.0 140 8,900 1.0 TJ = 80C 117.8 TJ = 90C 1,032,200 TJ = 100C 80 TJ = 110C Time, Years TJ = 120C Time, Hours FAILURE RATE OF PLASTIC = CERAMIC UNTIL INTERMETALLICS OCCUR TJ = 130C Junction Temperature C NORMALIZED FAILURE RATE DEVICE JUNCTION TEMPERATURE VERSUS TIME TO 0.1% BOND FAILURES 1 1 10 100 1000 TIME, YEARS Figure 2. Failure Rate vs. Time Junction Temperature http://onsemi.com 2 NLAS324 DC CHARACTERISTICS - Digital Section (Voltages Referenced to GND) Guaranteed Max Limit Symbol Parameter Condition VCC -55 to 25C <85C <125C Unit VIH Minimum High- Level Input Voltage, Enable Inputs 2.0 3.0 4.5 5.5 1.5 2.1 3.15 3.85 1.5 2.1 3.15 3.85 1.5 2.1 3.15 3.85 V VIL Maximum Low- Level Input Voltage, Enable Inputs 2.0 3.0 4.5 5.5 0.5 0.9 1.35 1.65 0.5 0.9 1.35 1.65 0.5 0.9 1.35 1.65 V IIN Maximum Input Leakage Current, Enable Inputs VIN = 5.5 V or GND 0 V to 5.5 V +0.1 +1.0 +1.0 A ICC Maximum Quiescent Supply Current (per package) Enable and VIS = VCC or GND 5.5 1.0 1.0 2.0 A DC ELECTRICAL CHARACTERISTICS - Analog Section Guaranteed Max Limit Symbol Parameter Condition VCC -55 to 25C <85C <125C Unit RON Maximum ON Resistance (Figures 8 - 12) VIN = VIH VIS = VCC to GND IIsI = <10.0mA 3.0 4.5 5.5 45 30 25 50 35 30 55 40 35 RFLAT(ON) ON Resistance Flatness VIN = VIH IIsI = <10.0mA VIS = 1V, 2V, 3.5V 4.5 4 4 5 INO(OFF) Off Leakage Current, Pin 2 (Figure 3) 5.5 1 10 100 nA ICOM(OFF) Off Leakage Current, Pin 1 (Figure 3) 5.5 1 10 100 nA VIN = VIL VNO = 1.0 V, VCOM = 4.5 V or VCOM = 1.0 V and VNO 4.5 V VIN = VIL VNO = 4.5 V or 1.0 V VCOM = 1.0 V or 4.5 V AC ELECTRICAL CHARACTERISTICS (Input tr = tf = 3.0 ns) Guaranteed Max Limit VCC Symbol Parameter Test Conditions (V) -55 to 25C Min <85C Typ Max Min Typ <125C Max Min Typ Max Unit tON Turn-On Time RL = 300 CL = 35 pF (Figures 4, 5, and 13) 2.03 .04. 55.5 7.0 5.0 4.5 4.5 14 10 9 9 16 12 11 11 16 12 11 11 ns tOFF Turn-Of f Time RL = 300 CL = 35 pF (Figures 4, 5, and 13) 2.03 .04. 5 5.5 11.0 7.0 5.0 5.0 22 14 10 10 24 16 12 12 24 16 12 12 ns Typical @ 25, VCC = 5.0 V CIN CNO or CNC CCOM(OFF) CCOM(ON) Maximum Input Capacitance, Select Input Analog I/O (switch off) Common I/O (switch off) Feedthrough (switch on) 8 10 10 20 http://onsemi.com 3 pF NLAS324 ADDITIONAL APPLICATION CHARACTERISTICS (Voltages Referenced to GND Unless Noted) Symbol Parameter Condition VCC Limit V 25°C Unit BW On-Channel Maximum On Channel -3dB 3dB Bandwidth or Minimum Frequency Response Res onse VIS = 0 dBm VIS centered between VCC and GND (Figures 6 and 14) 3.0 4.5 5.5 190 200 220 MHz VONL Maximum Feedthrough On Loss VIS = 0 dBm @ 10 kHz VIS centered between VCC and GND (Figure 6) 3.0 4.5 5.5 -2 2 -2 2 -2 dB VISO Off-Channel Off Channel Isolation kHz; VIS = 1 V RMS f = 100 kHz VIS centered between VCC and GND (Figures 6 and 15) 3.0 4.5 5.5 -93 93 dB Q Charge Injection Enable In Input ut to Common I/O VIS = VCC to GND, FIS = 20 kHz tr = tf = 3 ns RIS = 0 , CL = 1000 pF Q = CL * ∆VOUT (Figures 7 and 16) 3.0 5.5 1.5 3.0 pC C Total Harmonic Distortion THD + Noise FIS = 20 Hz to 1 MHz, RL = Rgen = 600 , CL = 50 pF F VIS = 3.0 VPP sine wave VIS = 5.0 VPP sine wave (Figure (Fi 17) 3.3 5.5 0.3 0.15 1.00E+05 1.00E+04 1.00E+03 1.00E+02 LEAKAGE (pA) THD 1.00E+01 ICOM(ON) 1.00E+00 1.00E-01 1.00E-02 1.00E-03 ICOM(OFF) 1.00E-04 1.00E-05 INO(OFF) 1.00E-06 1.00E-07 -55 -35 -15 5 25 45 65 85 105 125 145 TEMPERATURE (°C) Figure 3. Switch Leakage vs. Temperature http://onsemi.com 4 % NLAS324 VCC DUT VCC 50% Input NO 50% 0V COM VOUT 0.1 F 300 VOH 35 pF 90% 90% Output VOL Input tON tOFF Figure 4. tON/tOFF VCC VCC 50% Input DUT 300 NO COM 50% 0V VOUT VOH 35 pF Output 10% 10% VOL Input tOFF Figure 5. tON/tOFF http://onsemi.com 5 tON NLAS324 DUT Reference COM Transmitted NO 50 Generator 50 Channel switch control/s test socket is normalized. Off isolation is measured across an off channel. On loss is the bandwidth of an On switch. VISO, Bandwidth and VONL are independent of the input signal direction. VVOUT for VIN at 100 kHz IN VOUT for VIN at 100 kHz to 50 MHz VONL = On Channel Loss = 20 Log VIN VISO = Off Channel Isolation = 20 Log Bandwidth (BW) = the frequency 3 dB below VONL Figure 6. Off Channel Isolation/On Channel Loss (BW)/Crosstalk (On Channel to Off Channel)/VONL DUT NO VCC VIN COM GND CL Output Off VIN Figure 7. Charge Injection: (Q) http://onsemi.com 6 On Off ∆VOUT NLAS324 80 80 70 70 60 VCC = 2.0 50 50 RON () RON () 60 40 VCC = 2.5 30 30 25°C VCC = 3.0 20 -55 °C 40 20 85°C VCC = 4.5 10 10 0 0 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 125°C 0 5 0.2 0.4 0.6 1.2 1.4 1.6 1.8 VCOM (VOLTS) Figure 8. RON vs. VCOM and VCC (@25C) Figure 9. RON vs. VCOM and Temperature, VCC = 2.0 V 2 30 40 -55 °C 25 35 30 20 RON () RON () 1 VIS (VOLTS) 45 -55 °C 25 20 25°C 15 10 15 125°C 25°C 85°C 10 85°C 5 125°C 5 0 0.8 0 0.2 0.4 0.6 0.8 1 1.2 1.4 1.6 1.8 2 0 2.2 2.4 0 0.3 0.6 0.9 1.2 1.5 1.8 2.1 2.4 2.7 VCOM (VOLTS) VCOM (VOLTS) Figure 10. RON vs. VCOM and Temperature, VCC = 2.5 V Figure 11. RON vs. VCOM and Temperature, VCC = 3.0 V 3 35.0 18 16 30.0 -55 °C 25°C 25.0 12 TIME (nS) RON () 14 85°C 10 8 15.0 4 5.0 2 0.0 2.0 0 tON 10.0 125°C 6 20.0 tOFF 0 0.4 0.8 1.2 1.6 2 2.4 2.8 3.2 3.6 4 4.4 3.0 4.5 5.0 5.5 VCC (V) VCOM (VOLTS) Figure 12. RON vs. VCOM and Temperature, VCC = 4.5 V Figure 13. Switching Time vs. Supply Voltage, T = 25C http://onsemi.com 7 NLAS324 0 0 0 BANDWIDTH (dB/Div) Phase (Degrees) 5 VCC = 5.0 V TA = 25°C 0.01 0.1 1 10 OFF ISOLATION (dB/Div) 10 PHASE (Degrees) Bandwidth (On - Loss) -50 VCC = 5.0 V TA = 25°C -100 100 300 0.01 0.1 FREQUENCY (MHz) 1 10 100 300 FREQUENCY (MHz) Figure 14. ON Channel Bandwidth and Phase Shift Over Frequency Figure 15. Off Channel Isolation 100 1.60 1.40 VCC = 5.0 V 1.20 10 0.80 THD (%) Q (pC) 1.00 VCC = 3.0 V 1 3.3 V 0.60 0.40 0.1 5.5 V 0.20 0.00 0.0 0.01 1.0 2.0 3.6 3.0 VCOM (V) 4.0 4.5 10 5.0 100 1000 10000 100000 1000000 FREQUENCY (Hz) Figure 16. Charge Injection vs. VCOM Figure 17. THD vs. Frequency http://onsemi.com 8 NLAS324 DEVICE ORDERING INFORMATION Device Nomenclature Device Order Number Circuit Indicator Technology Device Function Package Suffix Package Type Tape and Reel Size NL AS 324 US US8 178 mm (7″) 3000 Unit NLAS324US CAVITY TAPE TOP TAPE TAPE TRAILER (Connected to Reel Hub) NO COMPONENTS 160 mm MIN COMPONENTS TAPE LEADER NO COMPONENTS 400 mm MIN DIRECTION OF FEED Figure 18. Tape Ends for Finished Goods TAPE DIMENSIONS mm 4.00 1.50 TYP 4.00 2.00 1.75 3.50 0.25 0.30 8.00 + - 0.10 1 1.00 ± 0.25 TYP DIRECTION OF FEED Figure 19. US8 Reel Configuration/Orientation http://onsemi.com 9 NLAS324 t MAX 1.5 mm MIN (0.06 in) A 13.0 mm 0.2 mm (0.512 in 0.008 in) 50 mm MIN (1.969 in) 20.2 mm MIN (0.795 in) FULL RADIUS G Figure 20. Reel Dimensions REEL DIMENSIONS Tape Size T and R Suffix A Max G t Max 8 mm US 178 mm (7 in) 8.4 mm, + 1.5 mm, -0.0 (0.33 in + 0.059 in, -0.00) 14.4 mm (0.56 in) DIRECTION OF FEED BARCODE LABEL POCKET Figure 21. Reel Winding Direction http://onsemi.com 10 HOLE NLAS324 PACKAGE DIMENSIONS US8 US SUFFIX CASE 493-01 ISSUE O NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETERS 3. DIMENSION A" DOES NOT INCLUDE MOLD FLASH, PROTRUSION OR GATE BURR. MOLD FLASH. PROTRUSION AND GATE BURR SHALL NOT EXCEED 0.140 MM (0.0055") PER SIDE. 4. DIMENSION B" DOES NOT INCLUDE INTER−LEAD FLASH OR PROTRUSION. INTER−LEAD FLASH AND PROTRUSION SHALL NOT E3XCEED 0.140 (0.0055") PER SIDE. 5. LEAD FINISH IS SOLDER PLATING WITH THICKNESS OF 0.0076−0. 0203 MM. (300−800 INCH). 6. ALL TOLERANCE UNLESS OTHERWISE SPECIFIED ±0.0508 (0.0002"). -XA 8 J -Y- 5 DETAIL E B L 1 4 R S G P U C -TSEATING PLANE H 0.10 (0.004) T K D N 0.10 (0.004) M T X Y R 0.10 TYP V M F DETAIL E 3.8 0.5 TYP ÉÉÉ ÉÉÉ ÉÉÉ ÉÉÉ ÉÉÉ ÉÉÉ ÉÉÉ ÉÉÉ ÉÉÉ ÉÉÉ 1.8 TYP 1.0 http://onsemi.com 11 0.3 TYP (mm) DIM A B C D F G H J K L M N P R S U V MILLIMETERS MIN MAX 1.90 2.10 2.20 2.40 0.60 0.90 0.17 0.25 0.20 0.35 0.50 BSC 0.40 REF 0.10 0.18 0.00 0.10 3.00 3.20 0 6 5 10 0.28 0.44 0.23 0.33 0.37 0.47 0.60 0.80 0.12 BSC INCHES MIN MAX 0.075 0.083 0.087 0.094 0.024 0.035 0.007 0.010 0.008 0.014 0.020 BSC 0.016 REF 0.004 0.007 0.000 0.004 0.118 0.126 0 6 5 10 0.011 0.017 0.009 0.013 0.015 0.019 0.024 0.031 0.005 BSC NLAS324 ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. PUBLICATION ORDERING INFORMATION Literature Fulfillment: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: [email protected] JAPAN: ON Semiconductor, Japan Customer Focus Center 2-9-1 Kamimeguro, Meguro-ku, Tokyo, Japan 153-0051 Phone: 81-3-5773-3850 Email: [email protected] ON Semiconductor Website: http://onsemi.com For additional information, please contact your local Sales Representative. N. American Technical Support: 800-282-9855 Toll Free USA/Canada http://onsemi.com 12 NLAS324/D