ONSEMI NCP5426SN13T2

NCP5426
LDO Regulator/Vibration
Motor Driver
The NCP5426 series of fixed output, 150 mA low dropout linear
regulators are designed to be an economical solution for a variety of
applications. Each device contains a voltage reference unit, an error
amplifier, a PNP power transistor, resistors for setting output voltage,
an under voltage lockout on the input, an enable pin, and current limit
and temperature limit protection circuits.
The NCP5426 is designed for driving a vibration motor using
ceramic capacitors on the output. The device is housed in the
micro−miniature TSOP−5 surface mount package. The NCP5426 is
available in output voltages of 1.2 V to 2.0 V in 0.1 V increments.
http://onsemi.com
5
1
TSOP−5
SN SUFFIX
CASE 483
Features
•
Wide Operating Voltage Range to 12 V
Internally Set Output Voltages
Enable Pin for On/Off Control
UVLO on the Input Voltage with Hysteresis
Current and Thermal Protection
Compatible with Ceramic, Tantalum or Aluminum Electrolytic
Capacitors
Pb−Free Package is Available
Typical Applications
PIN CONNECTIONS AND
MARKING DIAGRAM
Enable
1
GND
2
N/C
3
5
Vin
4
Vout
xxxYW
•
•
•
•
•
•
xxx = Version
Y = Year
W = Work Week
• Vibration Motor Driver
Vin
Vout
(Top View)
4
5
UVLO
Thermal
Shutdown
ORDERING INFORMATION
Driver w/
Current
Limit
See detailed ordering and shipping information in the package
dimensions section on page 7 of this data sheet.
Enable
ON
1
OFF
GND
2
This device contains 47 active transistors.
Figure 1. Internal Schematic
 Semiconductor Components Industries, LLC, 2004
June, 2004 − Rev. 4
1
Publication Order Number:
NCP5426/D
NCP5426
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
DETAILED PIN DESCRIPTION
Pin
Name
Description
1
Enable
The enable pin allows the user to control the output. A low signal disables the output and places
the device into a low current standby mode.
2
GND
Ground pin.
3
N/C
This pin is not connected to the device.
4
Vout
Regulated output voltage.
5
Vin
Input voltage.
MAXIMUM RATINGS
Rating
Symbol
Max Voltage, All Pins
Value
Unit
VMAX
12
V
Power Dissipation to Air
PA
150
mW
Power Dissipation, Board Mounted
P
600
mW
Operating and Storage Temperature
TA
−40 to 85
°C
Thermal Resistance
TJA
300
°C/W
Junction Temperature
TJ
125
°C
Maximum ratings are those values beyond which device damage can occur. Maximum ratings applied to the device are individual stress limit
values (not normal operating conditions) and are not valid simultaneously. If these limits are exceeded, device functional operation is not implied,
damage may occur and reliability may be affected.
ELECTRICAL CHARACTERISTICS (TA = 25°C, for min/max values TA is the operating junction temperature that
applies, VCC = 3.5 V, unless otherwise noted)
Characteristic
Symbol
Min
Operating Voltage
Typ
Max
Unit
VCC
−
−
12
V
Operating Voltage Turn On, Iout = 30 mA, Increasing VCC
VCCON
−
2.6
2.8
V
Operating Voltage Turn Off, Iout = 30 mA, Decreasing VCC
VCCOFF
2.0
2.1
2.2
V
Operating Voltage Hysteresis, Iout = 30 mA
VCC(hyst)
400
500
600
mV
ICC
−
120
240
A
ICC(uvlo)
−
80
160
A
Operating Current No Load
Operating Current, VCC = 1.8 V, Enable High
ICC(off)
−
−
0.1
A
Maximum Output Current, Vout = 0.95 *Vnom
Iout(max)
150
−
−
mA
Overcurrent Protection, Vout = 0 V
Iout(limit)
−
270
−
mA
Load Regulation, Vin = 3.5 V, Iout 1.0 to 100 mA
Regload
−
30
60
mV
Line Regulation, Iout = 30 mA, Vin 3.0 to 5.0 V
Regline
−
10
20
mV
RR
55
70
−
dB
Operating Current, Enable Low
Ripple Rejection, Vin 3.5 V, f 120 Hz, Vpp 1.0 V, Iout 30 mA
Tstd
−
150
−
°C
VCC H to L/T
−
200
−
ppm/°C
Vo/T
−
100
−
ppm/°C
Enable Pin High Threshold
Veh
1.6
−
−
V
Enable Pin Low Threshold
Vel
−
−
0.4
V
Enable Pin Current, Ve = 1.6 V
le
−
5.0
10
A
Vout
1.261
1.3
1.339
V
Temperature Shutdown
VCC Low Detector Temperature Coefficient, Iout = 30 mA,
T = −40 to 85°C
Vout Temperature Coefficient
−1.3 V
Output Voltage, Iout = 30 mA
http://onsemi.com
2
NCP5426
20
1.4
Vin = 3.5 V
Ve = 2.5 V
Vout = 1.3 V
Cout = 1.0 F
12
8
1.2
OUTPUT VOLTAGE (V)
LOAD REGULATION (mV)
16
4
0
−4
−8
−12
1.0
0.8
0.6
0.4
0.2
−16
−20
0
25
50
100
75
0
150
0
50
100
150
200
250
OUTPUT CURRENT (mA)
Figure 2. Load Regulation NCP5426
Figure 3. Current Limit NCP5426
136
134
300
2.7
Vin = 3.5 V
Iout = 0 mA
Vout(nom) = 1.3 V
Ve = Vin
2.6
Vth ON
2.5
132
UVLO (V)
QUIESCENT CURRENT (A)
125
OUTPUT CURRENT (mA)
140
138
130
128
126
124
2.4
2.3
2.2
122
2.1
120
Vth OFF
0
−25
25
50
75
100
125
2.0
−50
10
60
125
TEMPERATURE (°C)
TEMPERATURE (°C)
Figure 4. Quiescent Current vs. Temperature
Figure 5. Undervoltage Lockout vs.
Temperature
90
Vin = 3.5 V
Vout = 1.3 V
Iout = 1.0 mA
Cout = 1.0 F
Ve = 2.5 V
80
70
60
50
OUTPUT VOLTAGE
DEVIATION (mV)
118
−50
50
0
Iout = 1 mA to 150 mA
40
Iout, OUTPUT
CURRENT (mA)
RIPPLE REJECTION (dB)
Vin = 3.5 V
Ve = 2.5 V
Vout(nom) = 1.3 V
30
20
10
0
100
1k
10 k
100 k
1M
150
Vin = 3.5 V
Vout = 1.3 V
Cin = 4.7 F
Cout = 4.7 F
0
100 200 300 400 500 600
700 800 900 1000
FREQUENCY (Hz)
TIME (s)
Figure 6. Ripple Rejection vs. Frequency
Figure 7. Load Transient Response
http://onsemi.com
3
NCP5426
7.00
ENABLE CURRENT (A)
ENABLE CURRENT (A)
4.00
3.75
3.50
3.25
3.00
−50
Vin = 3.5 V
Ve = 1.6 V
Iout = 30 mA
−25
0
50
100
75
6.75
6.50
6.25
Vin = 3.5 V
Ve = 2.5 V
Iout = 30 mA
6.00
−50
125
50
75
100
125
TEMPERATURE (°C)
TEMPERATURE (°C)
Figure 8. Enable Current vs. Temperature
Figure 9. Enable Current vs. Temperature
0.90
Vin = 3.5 V
Vout = 1.3 V
50 s/div
0.80
LINE REGULATION (mV)
0
−25
0.70
1.3 V
Vout
0.60
0.50
0
0.40
100 mA
0.30
Iout
0.20
Vout = 1.3 V
Iout = 30 mA
Cout = 1 F
0.10
0
0
3
6
9
12
Cin = Cout = 4.7 F
Vin (V)
Figure 10. Line Regulation
Figure 11. Resistive Transient Response for
Switching the Enable Pin, Rout − 13 Ohms
Vin = 3.5 V
Vout = 1.3 V
100 ms/div
1.3 V
Vout
0
50 mA
Iout
0 mA
Cin = Cout = 4.7 F
Figure 12. Transient Response for Switching
the Enable Pin, Vibration Motor Load
http://onsemi.com
4
NCP5426
DEFINITIONS
Load Regulation
Line Regulation
The change in output voltage for a change in output load
current at a constant temperature and input voltage.
The change in output voltage for a change in input voltage.
The measurement is made under conditions of low
dissipation or by using pulse technique such that the average
chip temperature is not significantly affected.
Dropout Voltage
The input/output differential at which the regulator output
no longer maintains regulation against further reductions in
input voltage. Measured when the output drops 2.0% below
its nominal. The junction temperature, load current, and
minimum input supply requirements affect the dropout level.
Line Transient Response
Typical over and undershoot response when input voltage
is excited with a given slope.
Thermal Protection
This is the integrated value of the output noise over a
specified frequency range. Input voltage and output load
current are kept constant during the measurement. Results
are expressed in VRMS or nV √Hz.
Internal thermal shutdown circuitry is provided to protect
the integrated circuit in the event that the maximum junction
temperature is exceeded. When activated at typically 150°C,
the regulator turns off. This feature is provided to prevent
failures from accidental overheating.
Quiescent Current
Maximum Package Power Dissipation
The current which flows through the ground pin when the
regulator operates without a load on its output: internal IC
operation, bias, etc. When the LDO becomes loaded, this
term is called the Ground current. It is actually the difference
between the input current (measured through the LDO input
pin) and the output current.
The power dissipation level at which the junction
temperature reaches its maximum operating value, i.e.
125°C.
Output Noise Voltage
http://onsemi.com
5
NCP5426
APPLICATIONS INFORMATION
The maximum dissipation the package can handle is
given by:
The following description will assist the system designer
to correctly use the NCP5426 in an application. The
NCP5426 is designed specifically for use with inductive
loads, typically Vibration Motors. The LDO is capable of
using ceramic and tantalum capacitors. Please refer to
Figure 13 for a typical system schematic.
T
TA
PD J(max)
RJA
TJ is not recommended to exceed 125°C. The NCP5426
can dissipate up to 400 mW @ 25°C. The power dissipated
by the NCP5426 can be calculated from the following
equation:
Input Decoupling
A capacitor, C1, is necessary on the input for normal
operation. A ceramic or tantalum capacitor with a minimum
value of 1.0 F is required. Higher values of capacitance and
lower ESR will improve the overall line and load transient
response.
Ptot [Vin * IGND (Iout)] [Vin Vout] * Iout
or
P Vout * Iout
VinMAX tot
IGND Iout
Output Decoupling
If a 150 mA output current is needed then the ground
current is extracted from the data sheet curves: 200 A @
150 mA. For an NCP5426SN18T1 (1.8 V), the maximum
input voltage will then be 4.4 V, good for a 1 Cell Li−ion
battery.
A capacitor, C2, is required for the NCP5426 to operate
normally. A ceramic or tantalum capacitor will suffice. The
selection of the output capacitor is dependant upon several
factors: output current, power up and down delays, inductive
kickback during power up and down. It is recommended the
output capacitor be as close to the output pin and ground pin
for the best system response.
Hints
Please be sure the Vin and GND lines are sufficiently wide.
When the impedance of these lines is high, there is a chance
to pick up noise or cause the regulator to malfunction. Set
external components, especially the output capacitor, as
close as possible to the circuit, and make leads as short as
possible.
Enable Pin
The enable pin will turn on or off the regulator. The enable
pin is active high. The internal input resistance of the enable
pin is high which will keep the current very low when the pin
is pulled high. A low threshold voltage permits the
NCP5426 to operate directly from microprocessors or
controllers.
ON
OFF
Thermal
Enable
As power across the NCP5426 increases, it might become
necessary to provide some thermal relief. The maximum
power dissipation supported by the device is dependent
upon board design and layout. Mounting pad configuration
on the PCB, the board material and the ambient temperature
effect the rate of junction temperature rise for the part. This
is stating that when the NCP5426 has good thermal
conductivity through the PCB, the junction temperature will
be relatively low with high power dissipation applications.
VCC
Vin
GND
N/C
Vibration
Motor
C1
Vout
C2
Figure 13. Typical Applications Circuit
for Driving a Vibration Motor
VCCON
VCCOFF
Vout Resistive Load
Vout Motor Load
Figure 14. Timing Diagram
http://onsemi.com
6
VCCHYST
VCC
NCP5426
ORDERING INFORMATION
Nominal Output Voltage*
Marking
Package
Shipping†
NCP5426SN13T1
1.3
LDZ
TSOP−5
3000 / Tape & Reel
NCP5426SN13T2
1.3
LDZ
TSOP−5
NCP5426SN13T2G
1.3
LDZ
TSOP−5
(Pb−Free)
Device
3000 / Tape & Reel
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
*Contact your ON Semiconductor sales representative for other Output Voltage options.
http://onsemi.com
7
NCP5426
PACKAGE DIMENSIONS
TSOP−5
SN SUFFIX
PLASTIC PACKAGE
CASE 483−02
ISSUE C
D
S
5
4
1
2
3
B
L
MILLIMETERS
INCHES
DIM MIN
MAX
MIN
MAX
A
2.90
3.10 0.1142 0.1220
B
1.30
1.70 0.0512 0.0669
C
0.90
1.10 0.0354 0.0433
D
0.25
0.50 0.0098 0.0197
G
0.85
1.05 0.0335 0.0413
H 0.013 0.100 0.0005 0.0040
J
0.10
0.26 0.0040 0.0102
K
0.20
0.60 0.0079 0.0236
L
1.25
1.55 0.0493 0.0610
M
0_
10 _
0_
10 _
S
2.50
3.00 0.0985 0.1181
G
A
J
C
0.05 (0.002)
H
M
K
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. MAXIMUM LEAD THICKNESS INCLUDES
LEAD FINISH THICKNESS. MINIMUM LEAD
THICKNESS IS THE MINIMUM THICKNESS
OF BASE MATERIAL.
4. A AND B DIMENSIONS DO NOT INCLUDE
MOLD FLASH, PROTRUSIONS, OR GATE
BURRS.
SOLDERING FOOTPRINT*
0.95
0.037
1.9
0.074
2.4
0.094
1.0
0.039
0.7
0.028
SCALE 10:1
mm inches
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
ON Semiconductor Website: http://onsemi.com
Order Literature: http://www.onsemi.com/litorder
Japan: ON Semiconductor, Japan Customer Focus Center
2−9−1 Kamimeguro, Meguro−ku, Tokyo, Japan 153−0051
Phone: 81−3−5773−3850
http://onsemi.com
8
For additional information, please contact your
local Sales Representative.
NCP5426/D