ONSEMI MC100EP16VTDTR2G

MC100EP16VT
3.3V / 5VECL Differential
Receiver/Driver with
Variable Output Swing and
Internal Input Termination
http://onsemi.com
Description
•
•
•
•
8
8
1
SOIC−8
D SUFFIX
CASE 751
220 ps Propagation Delay
Maximum Frequency > 4 GHz Typical (See Graph)
The 100 Series Contains Temperature Compensation
PECL Mode Operating Range: VCC = 3.0 V to 5.5 V
with VEE = 0 V
NECL Mode Operating Range: VCC = 0 V
with VEE = −3.0 V to −5.5 V
Open Input Default State
50 W Internal Termination Resistor
Pb−Free Packages are Available
1
KEP63
ALYW
G
8
8
1
TSSOP−8
DT SUFFIX
CASE 948R
DFN8
MN SUFFIX
CASE 506AA
Features
•
•
•
•
MARKING DIAGRAMS*
1
KP63
ALYWG
G
3I MG
G
The MC100EP16VT is a differential receiver functionally equivalent
to the 100EP16 with input pins controlling the amplitude of the outputs
(pin 1) and providing an internal termination network (pin 4).
The VCTRL input pin controls the output amplitude of the EP16VT
and is referenced to VCC. (See Figure 4.) The operational range of the
VCTRL input is from VBB (a supply at VCC−1.42 V, maximum
output amplitude) to VCC (minimum output amplitude). VBB is an
externally supplied voltage equal to VCC−1.42 V (See Figures 2
and Figure 3). A variable resistor between VCC and VBB, with the
wiper driving VCTRL, can control the output amplitude. Typical
application circuits and a VCTRL Voltage vs. Output Amplitude graph
are described in this data sheet. When left open, the VCTRL pin will be
internally pulled down to VEE and operate as a standard EP16, with
100% output amplitude.
The VTT input pin offers an internal termination network for a 50 W
line impedance environment, shown in Figure 1. For further reference,
see Application Note AND8020, Termination of ECL Logic Devices.
Input considerations are required for D and D under no signal conditions
to prevent instability.
Special considerations are required for differential inputs under No
Signal conditions to prevent instability.
A
L
Y
W
M
G
1
4
= Assembly Location
= Wafer Lot
= Year
= Work Week
= Date Code
= Pb−Free Package
(Note: Microdot may be in either location)
*For additional marking information, refer to
Application Note AND8002/D.
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 9 of this data sheet.
© Semiconductor Components Industries, LLC, 2006
December, 2006 − Rev. 3
1
Publication Order Number:
MC100EP16VT/D
MC100EP16VT
VCTRL
D
1
8
2
7
Table 1. PIN DESCRIPTION
VCC
Q
50 W
D
3
6
Q
50 W
VTT
4
5
VEE
PIN
FUNCTION
D, D
ECL Data Inputs
Q, Q
ECL Data Outputs
VCTRL*
Output Swing Control
VTT
Termination Supply
VCC
Positive Supply
VEE
Negative Supply
EP
Exposed pad must be
connected to a sufficient thermal conduit. Electrically connect
to the most negative supply or
leave floating open.
Figure 1. 8−Lead Pinout (Top View) and Logic Diagram
* Pin will default LOW when left open.
Table 2. ATTRIBUTES
Characteristics
Value
Internal Input Pulldown Resistor
75 kW
Internal Input Pullup Resistor
ESD Protection
N/A
Human Body Model
Machine Model
Charged Device Model
Moisture Sensitivity, Indefinite Time Out of Drypack (Note 1)
SOIC−8
TSSOP−8
DFN8
Flammability Rating
Value
Oxygen Index: 28 to 34
Transistor Count
> 4 kV
> 200 V
> 2 kV
Pb Pkg
Pb−Free Pkg
Level 1
Level 1
Level 1
Level 1
Level 3
Level 1
UL 94 V−0 @ 0.125 in
140 Devices
Meets or exceeds JEDEC Spec EIA/JESD78 IC Latchup Test
1. For additional information, see Application Note AND8003/D.
http://onsemi.com
2
MC100EP16VT
Table 3. MAXIMUM RATINGS
Rating
Unit
VCC
Symbol
PECL Mode Power Supply
Parameter
VEE = 0 V
Condition 1
6
V
VEE
NECL Mode Power Supply
VCC = 0 V
−6
V
VI
PECL Mode Input Voltage
NECL Mode Input Voltage
VEE = 0 V
VCC = 0 V
6
−6
V
V
Iout
Output Current
Continuous
Surge
50
100
mA
mA
TA
Operating Temperature Range
−40 to +85
°C
Tstg
Storage Temperature Range
−65 to +150
°C
qJA
Thermal Resistance (Junction−to−Ambient)
0 lfpm
500 lfpm
8 SOIC
8 SOIC
190
130
°C/W
°C/W
qJC
Thermal Resistance (Junction−to−Case)
Standard Board
8 SOIC
41 to 44
°C/W
qJA
Thermal Resistance (Junction−to−Ambient)
0 lfpm
500 lfpm
8 TSSOP
8 TSSOP
185
140
°C/W
°C/W
qJC
Thermal Resistance (Junction−to−Case)
Standard Board
8 TSSOP
41 to 44 ± 5%
°C/W
qJA
Thermal Resistance (Junction−to−Ambient)
0 lfpm
500 lfpm
DFN8
DFN8
129
84
°C/W
°C/W
Tsol
Wave Solder
<2 to 3 sec @ 248°C
<2 to 3 sec @ 260°C
265
265
°C
Pb
Pb−Free
Condition 2
VI VCC
VI VEE
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
Table 4. DC CHARACTERISTICS, PECL VCC = 3.3 V, VEE = 0 V (Note 2)
−40°C
Symbol
Characteristic
IEE
Power Supply Current
VOH
Output HIGH Voltage (Max Swing)
(Note 3)
VCC VCTRL VEE
VOL
Output LOW Voltage (Max Swing)
(Note 3)
VCTRL VBB
85°C
Min
Typ
Max
Min
Typ
Max
Min
Typ
Max
Unit
30
36
42
31
38
44
32
40
48
mA
2405
2155
2405
2155
2405
mV
1605
1355
1605
1355
2155
mV
1355
VCC VCTRL > VBB
VCTRL = VCC (Min Swing)
25°C
1490
See
Fig.2
2105
2230
1520
See
Fig.2
2355
2095
2220
1520
1605
See
Fig.2
2345
2065
2190
2315
VIH
D, D Input HIGH Voltage (Single−Ended)
2075
2420
2075
2420
2075
2420
mV
VIL
D, D Input LOW Voltage (Single−Ended)
1355
1675
1355
1675
1355
1675
mV
VCTRL
Input Voltage (VCTRL)
VEE
VCC
VEE
VCC
VEE
VCC
mV
VIHCMR
Input HIGH Voltage Common Mode Range
(Differential Configuration) (Note 4)
2.0
2.9
2.0
2.9
2.0
2.9
V
IIH
Input HIGH Current
(VTT Open)
150
mA
IIL
Input LOW Current
(VTT Open)
150
−150
150
−150
−150
mA
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
2. Input and output parameters vary 1:1 with VCC. VEE can vary +0.3 V to −2.2 V.
3. All loading with 50 W to VCC − 2.0 V. VOH does not change with VCTRL. VOL changes with VCTRL. VCTRL is referenced to VCC.
4. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential
input signal.
http://onsemi.com
3
MC100EP16VT
Table 5. DC CHARACTERISTICS, PECL VCC = 5.0 V, VEE = 0 V (Note 5)
−40°C
Symbol
Characteristic
IEE
Power Supply Current
VOH
Output HIGH Voltage (Note 6)
VCC > VCTRL > VEE
VOL
Output LOW Voltage (Max Swing)
(Note 6)
VCTRL VBB
85°C
Typ
Max
Min
Typ
Max
Min
Typ
Max
Unit
30
36
42
31
38
44
32
40
48
mA
3855
3980
4105
3855
3980
4105
3855
3980
4105
mV
3055
3190
3305
3055
3220
3305
3055
3220
3305
mV
VCC VCTRL > VBB
VCTRL = VCC (Min Swing)
25°C
Min
See
Fig.2
3805
3930
See
Fig.2
4055
3795
3920
See
Fig.2
4045
3765
3890
4015
VIH
D, D Input HIGH Voltage (Single−Ended)
3775
4120
3775
4120
3775
4120
mV
VIL
D, D Input LOW Voltage (Single−Ended)
3055
3375
3055
3375
3055
3375
mV
VCTRL
Input Voltage (VCTRL)
VEE
VCC
VEE
VCC
VEE
VCC
mV
VIHCMR
Input HIGH Voltage Common Mode
Range (Differential Configuration) (Note 7)
2.0
4.6
2.0
4.6
2.0
4.6
V
IIH
Input HIGH Current
(VTT Open)
150
mA
IIL
Input LOW Current
(VTT Open)
150
−150
150
−150
−150
mA
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
5. Input and output parameters vary 1:1 with VCC. VEE can vary +2.0 V to −0.5 V.
6. All loading with 50 W to VCC − 2.0 V. VOH does not change with VCTRL. VOL changes with VCTRL. VCTRL is referenced to VCC.
7. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential
input signal.
http://onsemi.com
4
MC100EP16VT
Table 6. DC CHARACTERISTICS, NECL VCC = 0 V; VEE = −5.5 V to −3.0 V (Note 8)
−40°C
Symbol
Characteristic
IEE
Power Supply Current
VOH
Output HIGH Voltage (Note 9)
VCC > VCTRL > VEE
VOL
Output LOW Voltage (Max Swing)
(Note 9)
VCTRL VBB
85°C
Typ
Max
Min
Typ
Max
Min
Typ
Max
Unit
30
36
42
31
38
44
32
40
48
mA
−1145
−1020
−895
−1145
−1020
−895
−1145
−1020
−895
mV
−1945
−1810
−1695
−1945
−1780
−1695
−1945
−1780
−1695
mV
VCC VCTRL > VBB
VCTRL = VCC (Min Swing)
25°C
Min
See
Fig.2
−1195
See
Fig.2
−1070
−945
−1205
−1080
See
Fig.2
−955
−1235
−1110
−985
VIH
D, D Input HIGH Voltage (Single−Ended)
−1225
−880
−1225
−880
−1225
−880
mV
VIL
D, D Input LOW Voltage (Single−Ended)
−1945
−1625
−1945
−1625
−1945
−1625
mV
VCTRL
Input Voltage (VCTRL)
VEE
VCC
VEE
VCC
VEE
VCC
mV
VIHCMR
Input HIGH Voltage Common Mode
Range (Differential Configuration)
(Note 10)
−0.4
V
IIH
Input HIGH Current
(VTT Open)
150
mA
IIL
Input LOW Current
(VTT Open)
VEE+2.0
−0.4
VEE+2.0
−0.4
150
VEE+2.0
150
−150
−150
−150
mA
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
8. Input and output parameters vary 1:1 with VCC.
9. All loading with 50 W to VCC − 2.0 V. VOH does not change with VCTRL. VOL changes with VCTRL. VCTRL is referenced to VCC.
10. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential
input signal.
Table 7. AC CHARACTERISTICS VCC = 0 V; VEE = −3.0 V to −5.5 V or VCC = 3.0 V to 5.5 V; VEE = 0 V (Note 11)
−40°C
Symbol
Characteristic
Min
fmax
Maximum Toggle Frequency
(See Figure 8. Fmax/JITTER)
tPLH,
tPHL
Propagation Delay to Output Differential
Max Swing
Min Swing
tSKEW
Typ
25°C
Max
Min
>4
Max
Min
>4
Typ
Max
>4
Unit
GHz
ps
300
250
350
300
Duty Cycle Skew (Note 12)
5.0
tJITTER
Cycle−to−Cycle Jitter
(See Figure 8. Fmax/JITTER)
VPP
Input Voltage Swing
(Differential Configuration) (Note 13)
tr, tf
Output Rise/Fall Times
(20% − 80%)
Max Swing Q
Min Swing
250
200
Typ
85°C
250
200
300
250
350
300
20
5.0
0.2
<1
150
800
1200
70
30
120
80
170
130
250
200
300
250
350
300
20
5.0
20
ps
0.2
<1
0.2
<1
ps
150
800
1200
150
800
1200
mV
80
20
130
70
180
120
100
20
150
70
200
120
ps
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
11. Measured using a 750 mV source, 50% duty cycle clock source. All loading with 50 W to VCC − 2.0 V.
12. Skew is measured between outputs under identical transitions. Duty cycle skew is defined only for differential operation when the delays
are measured from the cross point of the inputs to the cross point of the outputs.
13. VPP(min) is minimum input swing for which AC parameters are guaranteed.
http://onsemi.com
5
MC100EP16VT
100
90
OUTPUT SWING (%)
80
70
60
50
40
30
20
10
0
0.0
0.5
1.0
VOLTS (V)
1.42
VBB
1.5
2.0
VPK−PK
Figure 2. VCC − VCTRL (pin #1)
VOH
Min Swing
Max Swing
VOL
0.0
0.5
1.0
VOLTS (V)
Figure 3. VCC − VCTRL
http://onsemi.com
6
1.42
VBB
1.5
2.0
MC100EP16VT
VCTRL +
VCTRL
D
1
8
2
7
Q*
6
Q*
5
VEE
VCC
50 W
D
3
50 W
VTT
4
Figure 4. Voltage Source Implementation, VCTRL Pin 1
VCC
VCTRL
VBB
D
1
8
2
7
Q*
6
Q*
5
VEE
VCC
50 W
D
3
50 W
VEE
VTT
4
Figure 5. Alternative Implementations, VCTRL Pin 1
VCTRL +
VCTRL
D
1
8
2
7
Q*
6
Q*
5
VEE
VCC
50 W
D
3
50 W
VCC−2 V
VTT
4
Figure 6. Standard Termination Method, VTT Pin 4
http://onsemi.com
7
MC100EP16VT
VCTRL +
VCTRL
D
1
8
2
7
Q*
6
Q*
5
VEE
VCC
50 W
D
3
50 W
VCC
RT
5.0 V
112 W
3.3 V
46 W
VTT
4
RT
VEE
1000
10
900
9
VOUTpp (mV)
800
2.00 V Below VCC
700
8
7
1.25 V Below VCC
600
6
1.00 V Below VCC
500
5
0.75 V Below VCC
400
4
300
3
200
ÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉ
0.25 V Below VCC
100
0
(JITTER)
0
500
1000
1500
2000
2500
3000
3500
2
1
4000
FREQUENCY (MHz)
Figure 8. Fmax/Jitter
Q
Zo = 50 W
D
Receiver
Device
Driver
Device
Q
D
Zo = 50 W
50 W
50 W
VTT
VTT = VCC − 2.0 V
Figure 9. Typical Termination for Output Driver and Device Evaluation
(See Application Note AND8020/D − Termination of ECL Logic Devices.)
http://onsemi.com
8
JITTEROUT ps (RMS)
Figure 7. Alternate “Y” Termination Method, VTT Pin 4
É
É
É
MC100EP16VT
ORDERING INFORMATION
Package
Shipping†
SOIC−8
98 Units / Rail
MC100EP16VTDG
SOIC−8
(Pb−Free)
98 Units / Rail
MC100EP16VTDR2
SOIC−8
2500 / Tape & Reel
MC100EP16VTDR2G
SOIC−8
(Pb−Free)
2500 / Tape & Reel
MC100EP16VTDT
TSSOP−8
100 Units / Rail
MC100EP16VTDTG
TSSOP−8
(Pb−Free)
100 Units / Rail
MC100EP16VTDTR2
TSSOP−8
2500 / Tape & Reel
MC100EP16VTDTR2G
TSSOP−8
(Pb−Free)
2500 / Tape & Reel
MC100EP16VTMNR4
DFN8
1000 / Tape & Reel
DFN8
(Pb−Free)
1000 / Tape & Reel
Device
MC100EP16VTD
MC100EP16VTMNR4G
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
Resource Reference of Application Notes
AN1405/D
− ECL Clock Distribution Techniques
AN1406/D
− Designing with PECL (ECL at +5.0 V)
AN1503/D
− ECLinPSt I/O SPiCE Modeling Kit
AN1504/D
− Metastability and the ECLinPS Family
AN1568/D
− Interfacing Between LVDS and ECL
AN1672/D
− The ECL Translator Guide
AND8001/D
− Odd Number Counters Design
AND8002/D
− Marking and Date Codes
AND8020/D
− Termination of ECL Logic Devices
AND8066/D
− Interfacing with ECLinPS
AND8090/D
− AC Characteristics of ECL Devices
http://onsemi.com
9
MC100EP16VT
PACKAGE DIMENSIONS
SOIC−8 NB
CASE 751−07
ISSUE AH
−X−
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION A AND B DO NOT INCLUDE
MOLD PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006)
PER SIDE.
5. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.127 (0.005) TOTAL
IN EXCESS OF THE D DIMENSION AT
MAXIMUM MATERIAL CONDITION.
6. 751−01 THRU 751−06 ARE OBSOLETE. NEW
STANDARD IS 751−07.
A
8
5
S
B
1
0.25 (0.010)
M
Y
M
4
−Y−
K
G
C
N
DIM
A
B
C
D
G
H
J
K
M
N
S
X 45 _
SEATING
PLANE
−Z−
H
0.10 (0.004)
D
0.25 (0.010)
M
Z Y
S
X
M
J
S
SOLDERING FOOTPRINT*
1.52
0.060
7.0
0.275
4.0
0.155
0.6
0.024
1.270
0.050
SCALE 6:1
mm Ǔ
ǒinches
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
http://onsemi.com
10
MILLIMETERS
MIN
MAX
4.80
5.00
3.80
4.00
1.35
1.75
0.33
0.51
1.27 BSC
0.10
0.25
0.19
0.25
0.40
1.27
0_
8_
0.25
0.50
5.80
6.20
INCHES
MIN
MAX
0.189
0.197
0.150
0.157
0.053
0.069
0.013
0.020
0.050 BSC
0.004
0.010
0.007
0.010
0.016
0.050
0 _
8 _
0.010
0.020
0.228
0.244
MC100EP16VT
PACKAGE DIMENSIONS
TSSOP−8
DT SUFFIX
PLASTIC TSSOP PACKAGE
CASE 948R−02
ISSUE A
8x
0.15 (0.006) T U
0.10 (0.004)
S
2X
L/2
L
8
5
1
PIN 1
IDENT
0.15 (0.006) T U
K REF
S
M
T U
V
S
0.25 (0.010)
B
−U−
4
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION A DOES NOT INCLUDE MOLD FLASH.
PROTRUSIONS OR GATE BURRS. MOLD FLASH
OR GATE BURRS SHALL NOT EXCEED 0.15
(0.006) PER SIDE.
4. DIMENSION B DOES NOT INCLUDE INTERLEAD
FLASH OR PROTRUSION. INTERLEAD FLASH OR
PROTRUSION SHALL NOT EXCEED 0.25 (0.010)
PER SIDE.
5. TERMINAL NUMBERS ARE SHOWN FOR
REFERENCE ONLY.
6. DIMENSION A AND B ARE TO BE DETERMINED
AT DATUM PLANE −W−.
S
M
A
−V−
F
DETAIL E
C
0.10 (0.004)
−T− SEATING
PLANE
D
−W−
G
DETAIL E
http://onsemi.com
11
DIM
A
B
C
D
F
G
K
L
M
MILLIMETERS
MIN
MAX
2.90
3.10
2.90
3.10
0.80
1.10
0.05
0.15
0.40
0.70
0.65 BSC
0.25
0.40
4.90 BSC
0_
6_
INCHES
MIN
MAX
0.114
0.122
0.114
0.122
0.031
0.043
0.002
0.006
0.016
0.028
0.026 BSC
0.010
0.016
0.193 BSC
0_
6_
MC100EP16VT
PACKAGE DIMENSIONS
DFN8
CASE 506AA−01
ISSUE D
D
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ASME Y14.5M, 1994 .
2. CONTROLLING DIMENSION: MILLIMETERS.
3. DIMENSION b APPLIES TO PLATED
TERMINAL AND IS MEASURED BETWEEN
0.25 AND 0.30 MM FROM TERMINAL.
4. COPLANARITY APPLIES TO THE EXPOSED
PAD AS WELL AS THE TERMINALS.
A
B
PIN ONE
REFERENCE
2X
0.10 C
2X
0.10 C
ÇÇÇ
ÇÇÇ
ÇÇÇ
ÇÇÇ
TOP VIEW
0.08 C
SEATING
PLANE
MILLIMETERS
MIN
MAX
0.80
1.00
0.00
0.05
0.20 REF
0.20
0.30
2.00 BSC
1.10
1.30
2.00 BSC
0.70
0.90
0.50 BSC
0.20
−−−
0.25
0.35
A
0.10 C
8X
DIM
A
A1
A3
b
D
D2
E
E2
e
K
L
E
(A3)
SIDE VIEW
A1
C
D2
e
e/2
4
1
8X
L
E2
K
8
5
8X
b
0.10 C A B
0.05 C
NOTE 3
BOTTOM VIEW
ECLinPS is a trademark of Semiconductor Components Industries, LLC (SCILLC).
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5773−3850
http://onsemi.com
12
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
MC100EP16VT/D