MC10EP08, MC100EP08 3.3V / 5VECL 2-Input Differential XOR/XNOR The MC10/100EP08 is a differential XOR/XNOR gate. The EP08 is ideal for applications requiring the fastest AC performance available. The 100 Series contains temperature compensation. http://onsemi.com • 250 ps Typical Propagation Delay • Maximum Frequency > 3 GHz Typical • PECL Mode Operating Range: VCC = 3.0 V to 5.5 V • MARKING DIAGRAMS* 8 8 with VEE = 0 V NECL Mode Operating Range: VCC = 0 V with VEE = –3.0 V to –5.5 V Open Input Default State 8 1 SO–8 D SUFFIX CASE 751 • • Safety Clamp on Inputs • Q Output Will Default LOW with Inputs Open or at VEE HEP08 ALYW 1 1 8 8 1 TSSOP–8 DT SUFFIX CASE 948R KEP08 ALYW 8 HP08 ALYW KP08 ALYW 1 1 H = MC10 K = MC100 A = Assembly Location L = Wafer Lot Y = Year W = Work Week *For additional information, see Application Note AND8002/D ORDERING INFORMATION Device Package MC10EP08D SO–8 98 Units/Rail MC10EP08DR2 SO–8 2500 Tape & Reel MC100EP08D SO–8 98 Units/Rail MC100EP08DR2 SO–8 2500 Tape & Reel MC10EP08DT TSSOP–8 100 Units/Rail MC10EP08DTR2 TSSOP–8 2500 Tape & Reel MC100EP08DT TSSOP–8 100 Units/Rail MC100EP08DTR2 TSSOP–8 Semiconductor Components Industries, LLC, 2001 April, 2001 – Rev. 3 1 Shipping 2500 Tape & Reel Publication Order Number: MC10EP08/D MC10EP08, MC100EP08 D0 1 8 2 D0 7 PIN DESCRIPTION VCC Q PIN FUNCTION D0, D1, D0, D1 ECL Data Inputs Q, Q ECL Data Outputs VCC Positive Supply VEE Negative Supply TRUTH TABLE 3 D1 6 4 D1 5 Q VEE D0* D1* D0** D1** Q Q L L H H L H L H H H L L H L H L L H H L H L L H * Pins will default LOW when left open. ** Pins will default to VCC/2 when left open. Figure 1. 8–Lead Pinout (Top View) and Logic Diagram ATTRIBUTES Characteristics Value Internal Input Pulldown Resistor 75 k Internal Input Pullup Resistor ESD Protection 37.5 k Human Body Model Machine Model Charged Device Model > 4 kV > 200 V > 2 kV Moisture Sensitivity, Indefinite Time Out of Drypack (Note 1.) Level 1 Flammability Rating Oxygen Index UL–94 code V–0 A 1/8” 28 to 34 Transistor Count 135 Meets or exceeds JEDEC Spec EIA/JESD78 IC Latchup Test 1. For additional information, see Application Note AND8003/D. MAXIMUM RATINGS (Note 2.) Symbol Parameter Condition 1 Condition 2 Rating Units VCC PECL Mode Power Supply VEE = 0 V 6 V VEE NECL Mode Power Supply VCC = 0 V –6 V VI Input PECL Mode In ut Voltage NECL Mode Input Voltage VEE = 0 V VCC = 0 V 6 –6 V V Iout Output Current Continuous Surge 50 100 mA mA TA Operating Temperature Range –40 to +85 °C Tstg Storage Temperature Range –65 to +150 °C θJA Thermal Resistance (Junction to Ambient) 0 LFPM 500 LFPM 8 SOIC 8 SOIC 190 130 °C/W °C/W θJC Thermal Resistance (Junction to Case) std bd 8 SOIC 41 to 44 °C/W θJA Thermal Resistance (Junction to Ambient) 0 LFPM 500 LFPM 8 TSSOP 8 TSSOP 185 140 °C/W °C/W θJC Thermal Resistance (Junction to Case) std bd 8 TSSOP 41 to 44 °C/W Tsol Wave Solder <2 to 3 sec @ 248°C 265 °C 2. Maximum Ratings are those values beyond which device damage may occur. http://onsemi.com 2 VI VCC VI VEE MC10EP08, MC100EP08 10EP DC CHARACTERISTICS, PECL VCC = 3.3 V, VEE = 0 V (Note 3.) –40°C Symbol Characteristic 25°C 85°C Min Typ Max Min Typ Max Min Typ Max Unit 20 28 36 20 30 38 20 32 38 mA Output HIGH Voltage (Note 4.) 2165 2290 2415 2230 2355 2480 2290 2415 2540 mV VOL Output LOW Voltage (Note 4.) 1365 1490 1615 1430 1555 1680 1490 1615 1740 mV VIH Input HIGH Voltage (Single Ended) 2090 2415 2155 2480 2215 2540 mV VIL Input LOW Voltage (Single Ended) 1365 1690 1430 1755 1490 1815 mV VIHCMR Input HIGH Voltage Common Mode Range (Differential) (Note 5.) 2.0 3.3 2.0 3.3 2.0 3.3 V IIH Input HIGH Current 150 µA IIL Input LOW Current IEE Power Supply Current VOH 150 D D 150 0.5 –150 0.5 –150 µA 0.5 –150 NOTE: EP circuits are designed to meet the DC specifications shown in the above table after thermal equilibrium has been established. The circuit is in a test socket or mounted on a printed circuit board and transverse airflow greater than 500 lfpm is maintained. 3. Input and output parameters vary 1:1 with VCC. VEE can vary +0.3 V to –2.2 V. 4. All loading with 50 ohms to VCC–2.0 volts. 5. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential input signal. 10EP DC CHARACTERISTICS, PECL VCC = 5.0 V, VEE = 0 V (Note 6.) –40°C Symbol Characteristic Min Typ 25°C Max Min Typ 85°C Max Min Typ Max Unit IEE Power Supply Current 20 28 36 20 30 38 20 32 38 mA VOH Output HIGH Voltage (Note 7.) 3865 3940 4115 3930 4055 4180 3990 4115 4240 mV VOL Output LOW Voltage (Note 7.) 3065 3190 3315 3130 3255 3380 3190 3315 3440 mV VIH Input HIGH Voltage (Single Ended) 3790 4115 3855 4180 3915 4240 mV VIL Input LOW Voltage (Single Ended) 3065 3390 3130 3455 3190 3515 mV VIHCMR Input HIGH Voltage Common Mode Range (Differential) (Note 8.) 2.0 5.0 2.0 5.0 2.0 5.0 V IIH Input HIGH Current 150 µA IIL Input LOW Current 150 D D 150 0.5 –150 0.5 –150 µA 0.5 –150 NOTE: EP circuits are designed to meet the DC specifications shown in the above table after thermal equilibrium has been established. The circuit is in a test socket or mounted on a printed circuit board and transverse airflow greater than 500 lfpm is maintained. 6. Input and output parameters vary 1:1 with VCC. VEE can vary +2.0 V to –0.5 V. 7. All loading with 50 ohms to VCC–2.0 volts. 8. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential input signal. 10EP DC CHARACTERISTICS, NECL VCC = 0 V; VEE = –5.5 V to –3.0 V (Note 9.) –40°C Symbol Characteristic 25°C 85°C Min Typ Max Min Typ Max Min Typ Max Unit 20 28 36 20 30 38 20 32 38 mA IEE Power Supply Current VOH Output HIGH Voltage (Note 10.) –1135 –1010 –885 –1070 –945 –820 –1010 –885 –760 mV VOL Output LOW Voltage (Note 10.) –1935 –1810 –1685 –1870 –1745 –1620 –1810 –1685 –1560 mV VIH Input HIGH Voltage (Single Ended) –1210 –885 –1145 –820 –1085 –760 mV VIL Input LOW Voltage (Single Ended) –1935 –1610 –1870 –1545 –1810 –1485 mV VIHCMR Input HIGH Voltage Common Mode Range (Differential) (Note 11.) 0.0 V IIH Input HIGH Current 150 µA IIL Input LOW Current VEE+2.0 0.0 VEE+2.0 150 D D 0.5 –150 0.0 VEE+2.0 150 0.5 –150 0.5 –150 µA NOTE: EP circuits are designed to meet the DC specifications shown in the above table after thermal equilibrium has been established. The circuit is in a test socket or mounted on a printed circuit board and transverse airflow greater than 500 lfpm is maintained. 9. Input and output parameters vary 1:1 with VCC. 10. All loading with 50 ohms to VCC–2.0 volts. 11. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential input signal. http://onsemi.com 3 MC10EP08, MC100EP08 100EP DC CHARACTERISTICS, PECL VCC = 3.3 V, VEE = 0 V (Note 12.) –40°C Symbol Characteristic 25°C 85°C Min Typ Max Min Typ Max Min Typ Max Unit 20 28 36 20 30 38 20 32 40 mA Output HIGH Voltage (Note 13.) 2155 2280 2405 2155 2280 2405 2155 2280 2405 mV VOL Output LOW Voltage (Note 13.) 1355 1480 1605 1355 1480 1605 1355 1480 1605 mV VIH Input HIGH Voltage (Single Ended) 2075 2420 2075 2420 2075 2420 mV VIL Input LOW Voltage (Single Ended) 1355 1675 1355 1675 1355 1675 mV VIHCMR Input HIGH Voltage Common Mode Range (Differential) (Note 14.) 2.0 3.3 2.0 3.3 2.0 3.3 V IIH Input HIGH Current 150 µA IIL Input LOW Current IEE Power Supply Current VOH 150 D D 150 0.5 –150 0.5 –150 µA 0.5 –150 NOTE: EP circuits are designed to meet the DC specifications shown in the above table after thermal equilibrium has been established. The circuit is in a test socket or mounted on a printed circuit board and transverse airflow greater than 500 lfpm is maintained. 12. Input and output parameters vary 1:1 with VCC. VEE can vary +0.3 V to –2.2 V. 13. All loading with 50 ohms to VCC–2.0 volts. 14. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential input signal. 100EP DC CHARACTERISTICS, PECL VCC = 5.0 V, VEE = 0 V (Note 15.) –40°C Symbol Characteristic 25°C 85°C Min Typ Max Min Typ Max Min Typ Max Unit 20 28 36 20 30 38 20 32 40 mA Output HIGH Voltage (Note 16.) 3855 3980 4105 3855 3980 4105 3855 3980 4105 mV VOL Output LOW Voltage (Note 16.) 3055 3180 3305 3055 3180 3305 3055 3180 3305 mV VIH Input HIGH Voltage (Single Ended) 3775 4120 3775 4120 3775 4120 mV VIL Input LOW Voltage (Single Ended) 3055 3375 3055 3375 3055 3375 mV VIHCMR Input HIGH Voltage Common Mode Range (Differential) (Note 17.) 2.0 5.0 2.0 5.0 2.0 5.0 V IIH Input HIGH Current 150 µA IIL Input LOW Current IEE Power Supply Current VOH 150 D D 150 0.5 –150 0.5 –150 µA 0.5 –150 NOTE: EP circuits are designed to meet the DC specifications shown in the above table after thermal equilibrium has been established. The circuit is in a test socket or mounted on a printed circuit board and transverse airflow greater than 500 lfpm is maintained. 15. Input and output parameters vary 1:1 with VCC. VEE can vary +2.0 V to –0.5 V. 16. All loading with 50 ohms to VCC–2.0 volts. 17. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential input signal. 100EP DC CHARACTERISTICS, NECL VCC = 0 V; VEE = –5.5 V to –3.0 V (Note 18.) –40°C Symbol Characteristic Min 25°C Typ Max Min Typ 85°C Max Min Typ Max Unit IEE Power Supply Current 20 28 36 20 30 38 20 32 40 mA VOH Output HIGH Voltage (Note 19.) –1145 –1020 –895 –1145 –1020 –895 –1145 –1020 –895 mV VOL Output LOW Voltage (Note 19.) –1945 –1820 –1695 –1945 –1820 –1695 –1945 –1820 –1695 mV VIH Input HIGH Voltage (Single Ended) –1225 –880 –1225 –880 –1225 –880 mV VIL Input LOW Voltage (Single Ended) –1945 –1625 –1945 –1625 –1945 –1625 mV VIHCMR Input HIGH Voltage Common Mode Range (Differential) (Note 20.) 0.0 V IIH Input HIGH Current 150 µA IIL Input LOW Current VEE+2.0 0.0 VEE+2.0 150 D D 0.5 –150 0.0 VEE+2.0 150 0.5 –150 0.5 –150 µA NOTE: EP circuits are designed to meet the DC specifications shown in the above table after thermal equilibrium has been established. The circuit is in a test socket or mounted on a printed circuit board and transverse airflow greater than 500 lfpm is maintained. 18. Input and output parameters vary 1:1 with VCC. 19. All loading with 50 ohms to VCC–2.0 volts. 20. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential input signal. http://onsemi.com 4 MC10EP08, MC100EP08 AC CHARACTERISTICS VCC = 0 V; VEE = –3.0 V to –5.5 V or VCC = 3.0 V to 5.5 V; VEE = 0 V (Note 21.) –40°C Symbol Characteristic Min fmax Maximum Frequency (See Figure 2. Fmax/JITTER) tPLH, tPHL Propagation Delay to Output Differential tJITTER Cycle–to–Cycle Jitter (See Figure 2. Fmax/JITTER) VPP Input Voltage Swing (Differential) tr tf Output Rise/Fall Times (20% – 80%) Typ 25°C Max Min >3 Typ 85°C Max Min >3 Typ >3 Q, Q 170 220 280 0.2 <1 150 800 1200 70 120 170 180 250 300 0.2 <1 150 800 1200 80 130 180 200 GHz 270 320 0.2 <1 ps 150 800 1200 mV 100 150 200 ps 900 9 800 8 700 7 600 6 500 5 400 4 300 3 ÉÉÉÉÉÉÉÉ ÉÉÉÉÉÉÉÉ ÉÉ ÉÉ 200 2 100 1 (JITTER) 0 1000 2000 JITTEROUT ps (RMS) VOUTpp (mV) Unit ps D, D to Q, Q 21. Measured using a 750 mV source, 50% duty cycle clock source. All loading with 50 ohms to V CC–2.0 V. 0 Max 3000 4000 FREQUENCY (MHz) Figure 2. Fmax/Jitter http://onsemi.com 5 5000 6000 MC10EP08, MC100EP08 Q D Receiver Device Driver Device Qb Db 50 50 V TT V TT = V CC – 2.0 V Figure 3. Typical Termination for Output Driver and Device Evaluation (See Application Note AND8020 – Termination of ECL Logic Devices.) Resource Reference of Application Notes AN1404 – ECLinPS Circuit Performance at Non–Standard VIH Levels AN1405 – ECL Clock Distribution Techniques AN1406 – Designing with PECL (ECL at +5.0 V) AN1504 – Metastability and the ECLinPS Family AN1568 – Interfacing Between LVDS and ECL AN1650 – Using Wire–OR Ties in ECLinPS Designs AN1672 – The ECL Translator Guide AND8001 – Odd Number Counters Design AND8002 – Marking and Date Codes AND8009 – ECLinPS Plus Spice I/O Model Kit AND8020 – Termination of ECL Logic Devices For an updated list of Application Notes, please see our website at http://onsemi.com. http://onsemi.com 6 MC10EP08, MC100EP08 PACKAGE DIMENSIONS SO–8 D SUFFIX PLASTIC SOIC PACKAGE CASE 751–07 ISSUE W –X– NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. A 8 5 0.25 (0.010) S B 1 M Y M 4 K –Y– G C N DIM A B C D G H J K M N S X 45 SEATING PLANE –Z– 0.10 (0.004) H M D 0.25 (0.010) M Z Y X S J S MILLIMETERS MIN MAX 4.80 5.00 3.80 4.00 1.35 1.75 0.33 0.51 1.27 BSC 0.10 0.25 0.19 0.25 0.40 1.27 0 8 0.25 0.50 5.80 6.20 INCHES MIN MAX 0.189 0.197 0.150 0.157 0.053 0.069 0.013 0.020 0.050 BSC 0.004 0.010 0.007 0.010 0.016 0.050 0 8 0.010 0.020 0.228 0.244 TSSOP–8 DT SUFFIX PLASTIC TSSOP PACKAGE CASE 948R–02 ISSUE A 8x 0.15 (0.006) T U K REF 0.10 (0.004) S 2X L/2 8 1 PIN 1 IDENT S T U V S NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A DOES NOT INCLUDE MOLD FLASH. PROTRUSIONS OR GATE BURRS. MOLD FLASH OR GATE BURRS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. DIMENSION B DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSION. INTERLEAD FLASH OR PROTRUSION SHALL NOT EXCEED 0.25 (0.010) PER SIDE. 5. TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 6. DIMENSION A AND B ARE TO BE DETERMINED AT DATUM PLANE -W-. S 5 0.25 (0.010) B –U– L 0.15 (0.006) T U M M 4 A –V– F DETAIL E C 0.10 (0.004) –T– SEATING PLANE D –W– G DETAIL E http://onsemi.com 7 DIM A B C D F G K L M MILLIMETERS MIN MAX 2.90 3.10 2.90 3.10 0.80 1.10 0.05 0.15 0.40 0.70 0.65 BSC 0.25 0.40 4.90 BSC 0 6 INCHES MIN MAX 0.114 0.122 0.114 0.122 0.031 0.043 0.002 0.006 0.016 0.028 0.026 BSC 0.010 0.016 0.193 BSC 0 6 MC10EP08, MC100EP08 ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. PUBLICATION ORDERING INFORMATION NORTH AMERICA Literature Fulfillment: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303–675–2175 or 800–344–3860 Toll Free USA/Canada Fax: 303–675–2176 or 800–344–3867 Toll Free USA/Canada Email: [email protected] Fax Response Line: 303–675–2167 or 800–344–3810 Toll Free USA/Canada N. American Technical Support: 800–282–9855 Toll Free USA/Canada EUROPE: LDC for ON Semiconductor – European Support German Phone: (+1) 303–308–7140 (Mon–Fri 2:30pm to 7:00pm CET) Email: ONlit–[email protected] French Phone: (+1) 303–308–7141 (Mon–Fri 2:00pm to 7:00pm CET) Email: ONlit–[email protected] English Phone: (+1) 303–308–7142 (Mon–Fri 12:00pm to 5:00pm GMT) Email: [email protected] CENTRAL/SOUTH AMERICA: Spanish Phone: 303–308–7143 (Mon–Fri 8:00am to 5:00pm MST) Email: ONlit–[email protected] Toll–Free from Mexico: Dial 01–800–288–2872 for Access – then Dial 866–297–9322 ASIA/PACIFIC: LDC for ON Semiconductor – Asia Support Phone: 303–675–2121 (Tue–Fri 9:00am to 1:00pm, Hong Kong Time) Toll Free from Hong Kong & Singapore: 001–800–4422–3781 Email: ONlit–[email protected] JAPAN: ON Semiconductor, Japan Customer Focus Center 4–32–1 Nishi–Gotanda, Shinagawa–ku, Tokyo, Japan 141–0031 Phone: 81–3–5740–2700 Email: [email protected] ON Semiconductor Website: http://onsemi.com EUROPEAN TOLL–FREE ACCESS*: 00–800–4422–3781 *Available from Germany, France, Italy, UK, Ireland For additional information, please contact your local Sales Representative. http://onsemi.com 8 MC10EP08/D