ONSEMI NCP693DMN12TCG

NCP693
1A CMOS Low-Dropout
Voltage Regulator
The NCP693 series of fixed output low dropout linear regulators are
designed for portable battery powered applications with high output
current requirement up to 1 A. Each device contains a voltage
reference unit, an error amplifier, a PMOS power transistor, resistors
for setting output voltage, a current limit circuits for over−current and
thermal−shutdown. A standby mode with ultra low supply current can
be realized with the chip enable function.
The device is housed in the DFN 1.8x2, 0.50P surface mount
package. Standard voltage versions are 0.8 V, 1.0 V, 1.2 V, 2.5 V and
3.3 V.
Maximum Operating Voltage of 6.5 V
Low Output Voltage Option down to 0.8 V
High Accuracy Output Voltage of 1.0%
Built−in Auto Discharge Function for D Version
These are Pb−Free Devices
XXX
XMM
XXXX
MM
1
= Specific Device Code
= Lot Number
PIN DESCRIPTION
Typical Applications
•
•
•
•
MARKING
DIAGRAM
UDFN6, 1.8x2, 0.5P
CASE 517BA
Features
•
•
•
•
•
http://onsemi.com
Battery Powered Instruments
Hand−Held Instruments
Camcorders and Cameras
Portable communication equipments
Vout 1
6 Vin
Vout 2
5 Vin
GND 3
4 CE
(Top View)
1
6
2
5
3
4
(Top View)
ORDERING AND MARKING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 11 of this data sheet.
© Semiconductor Components Industries, LLC, 2009
September, 2009 − Rev. 0
1
Publication Order Number:
NCP639/D
NCP693
Vin
Vout
Vin
Vout
Vin
Vout
Vin
Vout
Vref
Vref
Current Limit &
Thermal Shutdown
CE
Current Limit &
Thermal Shutdown
CE
GND
GND
Version H (NCP693HMNxxTCG)
Version D (NCP693DMNxxTCG)
Figure 1. Internal Block Diagram
PIN FUNCTION DESCRIPTION
Pin No.
Pin Name
1
Vout
Regulated output voltage.
Description
2
Vout
Regulated output voltage.
3
GND
Power supply ground.
4
CE
This input is used to place the device into low−power standby. When this input is pulled low, the device
is disabled. If this function is not used, Enable should be connected to Vin.
5
Vin
Positive power supply input voltage.
6
Vin
Positive power supply input voltage.
EP
GND
Power supply ground.
MAXIMUM RATINGS
Rating
Symbol
Value
Unit
Input Voltage
Vin
7
V
Enable Voltage
VCE
−0.3 to Vin
V
Output Voltage
Vout
−0.3 to Vin + 0.3
V
TJ
+150
°C
Operating Junction Temperature
Operating Ambient Temperature
TA
−40 to +85
°C
Storage Temperature
Tstg
−55 to +125
°C
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
1. This device series contains ESD protection and exceeds the following tests:
Human Body Model 2000 V per (JEDEC 22−A114−B)
Machine Model Method 200 V
THERMAL CHARACTERISTICS
Symbol
Test Conditions
Typical Value
Unit
Junction−to−Ambient
Rating
RqJA
1 oz Copper Thickness, 100 mm2
114
°C/W
PSIJ−Lead 2
YJ−L2
1 oz Copper Thickness, 100 mm2
25
°C/W
880
mW
Power Dissipation
NOTE:
PD
Single component mounted on an 80 x 80 x 1.5 mm FR4 PCB with stated copper head spreading area. Using the following
boundary conditions as stated in EIA/JESD 51−1, 2, 3, 7, 12.
http://onsemi.com
2
NCP693
ELECTRICAL CHARACTERISTICS (Vin = Vout(nom) + 1.0 V, VCE = Vin, Cin = 2.2 mF, Cout = 2.2 mF, TA = 25°C,
unless otherwise noted)
Symbol
Characteristic
Min
Typ
Max
0.785
0.985
1.185
2.475
3.267
0.8
1.0
1.2
2.5
3.3
0.815
1.015
1.215
2.525
3.333
0.760
0.960
1.160
2.435
3.214
0.8
1.0
1.2
2.5
3.3
0.827
1.027
1.227
2.545
3.359
Output Voltage (TA = 25°C, Iout = 10 mA)
0.8 V
1.0 V
1.2 V
2.5 V
3.3 V
Vout
Output Voltage (TA = − 40°C to 85°C, Iout = 10 mA)
0.8 V
1.0 V
1.2 V
2.5 V
3.3 V
Vout
Output Current
Iout
Input Voltage
Vin
1.6
Regline
−
Load Regulation (Iout = 1 mA to 300 mA, Vin = Vout + 2.0 V)
Regload03
Load Regulation (Iout = 1 mA to 1 A, Vin = Vout + 2.0 V)
Regload1
Line Regulation (Vin = Vout + 1.0 V to 6.5 V, Iout = 10 mA)
Unit
V
V
1
A
6.5
V
0.05
0.1
%/V
−
20
40
mV
−
80
120
mV
Iss
65
90
mA
Istby
0.15
0.6
mA
Short Current Limit (Vout = 0 V)
Ish
250
Output Voltage Temperature Coefficient
Tc
Supply Current (Iout = 0 A, Vin = 6.5 V)
Standby Current (VCE = 0 V, Vin = 6.5 V)
Enable Input Threshold Voltage
(Voltage Increasing, Output Turns On, Logic High)
(Voltage Decreasing, Output Turns Off, Logic Low)
VthCE
Enable Pulldown Current
mA
−
$100
−
1.0
−
−
−
−
0.4
ppm/°C
V
0.3
Drop Output Voltage (TA = 25°C, Iout = 300 mA)
0.8 V
1.0 V
1.2 V
2.5 V
3.3 V
Vin−Vout
Drop Output Voltage (TA = 25°C, Iout = 1 A)
0.8 V
1.0 V
1.2 V
2.5 V
3.3 V
Vin−Vout
mA
0.670
0.450
0.300
0.150
0.130
0.780
0.610
0.500
0.310
0.170
1.150
1.000
0.870
0.500
0.430
1.650
1.450
1.380
1.100
0.650
V
V
Ripple Rejection (Ripple 200 mVpp, Iout = 100 mA, f = 1 kHz)
PSRR
70
dB
Output Noise (BW = 10 Hz to 100 kHz, Iout = 1 mA)
Vnoise
45
mVrms
Tshd/Hyst
165/30
°C
RDS(on)
30
W
Thermal Shutdown Temperature/Hysteresis
RDS(on) of additional output transistor (D version only)
2. Maximum package power dissipation limits must be observed.
3. Low duty cycle pulse techniques are used during testing to maintain the junction temperature as close to ambient as possible.
http://onsemi.com
3
NCP693
APPLICATIONS INFORMATION
(NCP693DMNxxTCG) have additional circuitry in order to
reach the turn−off speed faster than normal type. When the
mode is into standby with CE signal, auto discharge
transistor turns on.
A typical application circuit for the NCP693 series is
shown in Figure 2.
Input Decoupling (C1)
A 2.2 mF capacitor either ceramic or tantalum is
recommended and should be connected as close as possible
to the pins of NCP693 device. Higher values and lower ESR
will improve the overall line transient response.
Hints
Please be sure the Vin and GND lines are sufficiently wide.
If their impedance is high, noise pickup or unstable
operation may result.
Set external components, especially the output capacitor,
as close as possible to the circuit, and make leads as short as
possible.
Output Decoupling (C2)
The minimum decoupling value is 2.2 mF and can be
augmented to fulfill stringent load transient requirements.
The regulator accepts ceramic chip capacitors as well as
tantalum devices. If a tantalum capacitor is used, and its ESR
is large, the loop oscillation may result. Because of this,
select C2 carefully considering its frequency characteristics.
Larger values improve noise rejection and load regulation
transient response.
Thermal
As power across the NCP693 increases, it might become
necessary to provide some thermal relief. The maximum
power dissipation supported by the device is dependent
upon board design and layout. Mounting pad configuration
on the PCB, the board material, and also the ambient
temperature effect the rate of temperature rise for the part.
This is stating that when the NCP693 has good thermal
conductivity through the PCB, the junction temperature will
be relatively low with high power dissipation applications.
Enable Operation
The enable pin CE will turn on or off the regulator. These
limits of threshold are covered in the electrical specification
section of this data sheet. If the enable is not used then the
pin should be connected to Vin. The D version devices
Figure 2. Typical Application Circuit
http://onsemi.com
4
NCP693
0.9
0.8
TA = 25°C
1.2
0.7
Vin = 1.4 V
0.6
1.6 V
2.0 V
OUTPUT VOLTAGE (V)
OUTPUT VOLTAGE (V)
1.4
TA = 25°C
2.5 V
0.5
0.4
0.3
0.2
1.0
Vin = 1.8 V
2.4 V
0.8
0.6
0.4
0.2
0.1
0.0
0.0
0.2
0.4
0.6
0.8
1.0
1.2
OUTPUT CURRENT (A)
1.4
0.0
0.0
1.6
Figure 3. Output Voltage vs. Output Current
NCP693xMN08TCG
1.4
1.6
3.0
2.5
Vin = 2.9 V
2.0
3.8 V
OUTPUT VOLTAGE (V)
OUTPUT VOLTAGE (V)
0.4
0.6
0.8
1.0
1.2
OUTPUT CURRENT (A)
3.5
TA = 25°C
3.3 V
1.5
1.0
0.5
Vin = 3.6 V
2.5
5.0 V
4.3 V
2.0
1.5
1.0
0.5
0.0
0.0
0.2
0.4
0.6
0.8
1.0
1.2
1.4
0.0
0.0
1.6
0.2
0.4
0.6
0.8
1.0
1.2
1.4
OUTPUT CURRENT (A)
OUTPUT CURRENT (A)
Figure 6. Output Voltage vs. Output Current
NCP693xMN33TCG
70.0
70.0
60.0
60.0
50.0
40.0
30.0
20.0
10.0
Iout = 0 V
0
TA = 25°C
Figure 5. Output Voltage vs. Output Current
NCP693xMN25TCG
SUPPLY CURRENT (mA)
SUPPLY CURRENT (mA)
0.2
Figure 4. Output Voltage vs. Output Current
NCP693xMN12TCG
3.0
0.0
3.0 V
1
2
3
4
5
INPUT VOLTAGE (V)
6
50.0
40.0
30.0
20.0
10.0
0.0
7
Iout = 0 V
0
Figure 7. Supply Current vs. Input Voltage
NCP693xMN08TCG
1
2
3
4
5
INPUT VOLTAGE (V)
6
Figure 8. Supply Current vs. Input Voltage
NCP693xMN12TCG
http://onsemi.com
5
1.6
7
70.0
70.0
60.0
60.0
SUPPLY CURRENT (mA)
SUPPLY CURRENT (mA)
NCP693
50.0
40.0
30.0
20.0
10.0
0.0
1
2
3
4
5
INPUT VOLTAGE (V)
40.0
30.0
20.0
10.0
Iout = 0 A
0
50.0
6
0.0
7
Iout = 0 V
0
Figure 9. Supply Current vs. Input Voltage
NCP693xMN25TCG
1
2
3
4
5
INPUT VOLTAGE (V)
1.215
Vout = 0.8 V
Vout = 1.2 V
0.802
1.210
OUTPUT VOLTAGE (V)
OUTPUT VOLTAGE (V)
7
Figure 10. Supply Current vs. Input Voltage
NCP693xMN33TCG
0.804
0.800
0.798
0.796
0.794
0.792
−40.0
−20.0
0.0
20.0
40.0
60.0
1.205
1.200
1.195
1.190
1.185
80.0
−40
−20
0
20
40
60
TEMPERATURE (°C)
TEMPERATURE (°C)
Figure 11. Output Voltage vs. Temperature
NCP693xMN08TCG
Figure 12. Output Voltage vs. Temperature
NCP693xMN12TCG
2.520
80
3.310
Vout = 2.5 V
2.515
Vout = 3.3 V
2.510
OUTPUT VOLTAGE (V)
OUTPUT VOLTAGE (V)
6
2.505
2.500
2.495
2.490
3.300
3.290
3.280
2.485
2.480
−40
−20
0
20
40
60
3.270
−40
80
−20
0
20
40
60
TEMPERATURE (°C)
TEMPERATURE (°C)
Figure 13. Output Voltage vs. Temperature
NCP693xMN25TCG
Figure 14. Output Voltage vs. Temperature
NCP693xMN33TCG
http://onsemi.com
6
80
NCP693
1.4
1.0
TA = 85°C
1.0
DROPOUT VOLTAGE (V)
DROPOUT VOLTAGE (V)
1.2
0.8
0.6
TA = −40°C
TA = 25°C
0.4
0.2
0.0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
0.2
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1.0
OUTPUT CURRENT (A)
Figure 16. Dropout Voltage vs. Output Current
NCP693xMN12TCG
0.6
TA = 85°C
TA = 25°C
0.4
DROPOUT VOLTAGE (V)
DROPOUT VOLTAGE (V)
TA = −40°C
0.4
OUTPUT CURRENT (A)
0.3
TA = −40°C
0.2
0.1
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
0.5
0.4
0.3
0.2
TA = −40°C
0.1
0.0
1.0
TA = 85°C
TA = 25°C
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1.0
OUTPUT CURRENT (A)
OUTPUT CURRENT (A)
Figure 17. Dropout Voltage vs. Output Current
NCP693xMN25TCG
Figure 18. Dropout Voltage vs. Output Current
NCP693xMN33TCG
90
90
80
80
70
70
IOUT = 1 mA
IOUT = 1 mA
60
PSRR (dB)
60
PSRR (dB)
0.6
Figure 15. Dropout Voltage vs. Output Current
NCP693xMN08TCG
0.5
50
40
IOUT = 100 mA
30
50
40
20
10
10
0.1
1.0
10.0
FREQUENCY (kHz)
100.0
0
1000
IOUT = 100 mA
30
20
0
TA = 85°C
TA = 25°C
0
0.1
1.0
0.6
0.0
0.8
0.1
1.0
10.0
100.0
FREQUENCY (kHz)
Figure 19. PSRR vs. Frequency
NCP693xMN08TCG
Figure 20. PSRR vs. Frequency
NCP693xMN12TCG
http://onsemi.com
7
1000
NCP693
90
90
80
80
70
IOUT = 1 mA
60
PSRR (dB)
PSRR (dB)
70
50
40
IOUT = 100 mA
30
60
50
40
20
10
10
1.0
10.0
IOUT = 100 mA
30
20
0
0.1
IOUT = 1 mA
100.0
0
0.1
1000
1.0
10.0
100.0
FREQUENCY (kHz)
FREQUENCY (kHz)
Figure 21. PSRR vs. Frequency
NCP693xMN25TCG
Figure 22. PSRR vs. Frequency
NCP693xMN33TCG
Figure 23. Turn Off Speed NCP693DMN08TCG
Figure 24. Turn Off Speed NCP693HMN08TCG
Figure 25. Turn On Speed NCP693xMN08CTG
Figure 26. Turn On Speed NCP693xMN08CTG
http://onsemi.com
8
1000
3.0
2.0
0.820
IOUT = 100 mA
COUT = 2.2 mF
0.815
VIN = step 1.8 V to 2.8 V
TA = 25°C
0.810
Input Voltage
1.5
0.805
INPUT VOLTAGE (V)
2.5
Output Voltage
1.0
0.800
0.5
0.0
0.795
0
10
20
30
40
50
60
70
80
OUTPUT VOLTAGE (V)
NCP693
0.790
100
90
TIME (ms)
Figure 27. Input Response NCP693xMN08TCG
6.0
3.320
3.315
Input Voltage
4.0
3.310
3.0
3.305
Output Voltage
2.0
3.300
IOUT = 100 mA
COUT = 2.2 mF
VIN = step 4.3 V to 5.3 V
TA = 25°C
1.0
0.0
0
10
20
30
40
50
60
70
80
90
3.290
100
TIME (ms)
Figure 28. Input Response NCP693xMN33TCG
http://onsemi.com
9
3.295
OUTPUT VOLTAGE (V)
INPUT VOLTAGE (V)
5.0
110
0.88
IOUT = 50 mA to 100 mA
COUT = 2.2 mF
VIN = 1.8 V
0.86
TA = 25°C
OUTPUT CURRENT (mA)
100
90
0.1 A/ms Slope
80
70
0.84
60
Output Current
50
0.82
40
Output Voltage
30
0.80
OUTPUT VALUE (V)
NCP693
20
10
0
10
20
30
40 50
TIME (ms)
60
70
80
0.78
100
90
80
3.37
IOUT = 50 mA to 100 mA
3.36
COUT = 2.2 mF
3.35
VIN = 4.3 V
TA = 25°C
3.34
70
3.33
110
OUTPUT CURRENT (mA)
100
0.1 A/ms Slope
90
60
3.32
Output Current
50
40
3.31
3.30
Output Voltage
30
3.29
3.28
20
10
0
10
20
30
40
50
60
70
80
90
3.27
100
TIME (ms)
Figure 30. Input Response NCP693xMN33TCG
http://onsemi.com
10
OUTPUT VALUE (V)
Figure 29. Input Response NCP693xMN08TCG
NCP693
ORDERING INFORMATION
Nominal
Output Voltage
Marking
Package
Shipping†
NCP693HMN08TCG
0.8
AM01
DFN
(Pb−Free)
5000 / Tape & Reel
NCP639HMN10TCG
1.0
AM03
DFN
(Pb−Free)
5000 / Tape & Reel
NCP693HMN12TCG
1.2
AM06
DFN
(Pb−Free)
5000 / Tape & Reel
NCP693HMN25TCG
2.5
AM20
DFN
(Pb−Free)
5000 / Tape & Reel
NCP693HMN33TCG
3.3
AM29
DFN
(Pb−Free)
5000 / Tape & Reel
NCP693DMN08TCG
0.8
AN01
DFN
(Pb−Free)
5000 / Tape & Reel
NCP693DMN10TCG
1.0
AN03
DFN
(Pb−Free)
5000 / Tape & Reel
NCP693DMN12TCG
1.2
AN06
DFN
(Pb−Free)
5000 / Tape & Reel
NCP693DMN25TCG
2.5
AN20
DFN
(Pb−Free)
5000 / Tape & Reel
NCP693DMN33TCG
3.3
AN29
DFN
(Pb−Free)
5000 / Tape & Reel
Device
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
http://onsemi.com
11
NCP693
PACKAGE DIMENSIONS
UDFN6, 1.8x2, 0.5P
CASE 517BA−01
ISSUE A
D
PIN ONE
LOCATION
A
B
ÍÍÍ
ÍÍÍ
ÍÍÍ
NOTES:
1. DIMENSIONING AND TOLERANCING PER ASME
Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETERS.
3. DIMENSION b APPLIES TO PLATED TERMINAL AND
IS MEASURED BETWEEN 0.15 AND 0.20mm FROM
THE TERMINAL TIP.
4. COPLANARITY APPLIES TO THE EXPOSED PAD AS
WELL AS THE TERMINALS.
ÇÇ
ÉÉ
ÉÉ
EXPOSED Cu
MOLD CMPD
DETAIL B
E
OPTIONAL
CONSTRUCTIONS
DIM
A
A1
A3
b
b1
D
D2
E
E2
e
K
L
L1
0.10 C
2X
2X
0.10 C
L
L
TOP VIEW
L1
A3
DETAIL B
DETAIL A
OPTIONAL
CONSTRUCTIONS
0.05 C
A
0.05 C
A1
NOTE 4
C
SIDE VIEW
RECOMMENDED
MOUNTING FOOTPRINT*
SEATING
PLANE
1.70
D2
b1
6X
1
DETAIL A
6
L
5X
0.25
6X
0.48
3
2X
K
MILLIMETERS
MIN
MAX
0.50
0.60
0.00
0.05
0.20 REF
0.15
0.30
0.20
0.40
1.80 BSC
1.50
1.70
2.00 BSC
0.90
1.10
0.50 BSC
0.20
--0.15
0.35
--0.10
4
5X
e
E2
b
1.10 2.30
1
0.10 C A
0.05 C
B
NOTE 3
0.35
BOTTOM VIEW
0.50
PITCH
DIMENSIONS: MILLIMETERS
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent
rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other
applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur.
Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries,
affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury
or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an
Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5773−3850
http://onsemi.com
12
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
NCP693/D