ONSEMI NTD12N10

NTD12N10
Preferred Device
Power MOSFET
12 Amps, 100 Volts N−Channel
Enhancement−Mode DPAK
Features
• Pb−Free Package is Available
• Source−to−Drain Diode Recovery Time Comparable to a
•
•
•
http://onsemi.com
Discrete Fast Recovery Diode
Avalanche Energy Specified
IDSS and RDS(on) Specified at Elevated Temperature
Mounting Information Provided for the DPAK Package
V(BR)DSS
RDS(on) TYP
ID MAX
100 V
165 m @ 10 V
12 A
N−Channel
D
Typical Applications
• PWM Motor Controls
• Power Supplies
• Converters
G
S
MAXIMUM RATINGS (TC = 25°C unless otherwise noted)
Unit
Drain−to−Source Voltage
VDSS
100
Vdc
Drain−to−Source Voltage (RGS = 1.0 M)
VDGR
100
Vdc
Gate−to−Source Voltage
− Continuous
− Non−Repetitive (tp ≤ 10 ms)
VGS
VGSM
± 20
± 30
Vdc
Vpk
ID
ID
12
7.0
36
Adc
56.6
0.38
1.76
1.28
W
W/°C
W
W
TJ, Tstg
−55 to
+175
°C
EAS
75
mJ
Drain Current − Continuous @ TA = 25°C
Drain Current − Continuous @ TA =100°C
Drain Current − Pulsed (Note 3)
Total Power Dissipation
Derate above 25°C
Total Power Dissipation @ TA = 25°C (Note 1)
Total Power Dissipation @ TA = 25°C (Note 2)
Operating and Storage Temperature Range
Single Pulse Drain−to−Source Avalanche
Energy − Starting TJ = 25°C
(VDD = 50 Vdc, VGS = 10 Vdc,
IL = 12 Apk, L = 1.0 mH, RG = 25 )
Thermal Resistance
− Junction to Case
− Junction to Ambient (Note 1)
− Junction to Ambient (Note 2)
Maximum Temperature for Soldering
Purposes, 1/8″ from case for 10 seconds
IDM
PD
August, 2004 − Rev. 6
4
Drain
4
1 2
3
DPAK
CASE 369C
(Surface Mounted)
STYLE 2
2
1
3
Drain
Gate
Source
Apk
4
Drain
4
1
2
DPAK−3
CASE 369D
(Straight Lead)
STYLE 2
3
1 2 3
Gate Drain Source
°C/W
RJC
RJA
RJA
2.65
85
117
TL
260
°C
Maximum ratings are those values beyond which device damage can occur.
Maximum ratings applied to the device are individual stress limit values (not
normal operating conditions) and are not valid simultaneously. If these limits
are exceeded, device functional operation is not implied, damage may occur
and reliability may be affected.
1. When surface mounted to an FR4 board using 0.5 sq in pad size.
2. When surface mounted to an FR4 board using the minimum recommended
pad size.
3. Pulse Test: Pulse Width = 10 s, Duty Cycle = 2%.
 Semiconductor Components Industries, LLC, 2004
MARKING
DIAGRAMS
1
AYWW
T12
N10
Value
AYWW
T12
N10
Symbol
Rating
T12N10
A
Y
WW
= Device Code
= Assembly Location
= Year
= Work Week
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 2 of this data sheet.
Preferred devices are recommended choices for future use
and best overall value.
Publication Order Number:
NTD12N10/D
NTD12N10
ELECTRICAL CHARACTERISTICS (TC = 25°C unless otherwise noted)
Characteristic
Symbol
Min
Typ
Max
Unit
100
−
−
135
−
−
−
−
−
−
5.0
50
−
−
± 100
2.0
−
3.1
−7.5
4.0
−
−
−
0.130
0.250
0.165
0.400
−
1.62
2.16
gFS
−
7.0
−
mhos
Ciss
−
390
550
pF
Coss
−
115
160
Crss
−
35
70
td(on)
−
11
20
tr
−
30
60
td(off)
−
22
40
OFF CHARACTERISTICS
Drain−to−Source Breakdown Voltage
(VGS = 0 Vdc, ID = 250 Adc)
Temperature Coefficient (Positive)
V(BR)DSS
Zero Gate Voltage Drain Current
(VGS = 0 Vdc, VDS = 100 Vdc, TJ = 25°C)
(VGS = 0 Vdc, VDS = 100 Vdc, TJ = 125°C)
IDSS
Gate−Body Leakage Current (VGS = ± 20 Vdc, VDS = 0)
IGSS
Vdc
mV/°C
Adc
nAdc
ON CHARACTERISTICS
Gate Threshold Voltage
VDS = VGS, ID = 250 Adc)
Temperature Coefficient (Negative)
VGS(th)
Static Drain−to−Source On−State Resistance
(VGS = 10 Vdc, ID = 6.0 Adc)
(VGS = 10 Vdc, ID = 6.0 Adc, TJ = 125°C)
RDS(on)
Drain−to−Source On−Voltage
(VGS = 10 Vdc, ID = 12 Adc)
VDS(on)
Forward Transconductance (VDS = 10 Vdc, ID = 6.0 Adc)
Vdc
mV/°C
Vdc
DYNAMIC CHARACTERISTICS
Input Capacitance
(VDS = 25 Vdc,
Vd VGS = 0 Vdc,
Vd
f = 1.0 MHz)
Output Capacitance
Reverse Transfer Capacitance
SWITCHING CHARACTERISTICS (Notes 4 & 5)
Turn−On Delay Time
Rise Time
(VDD = 80 Vdc, ID = 12 Adc,
VGS = 10 Vdc, RG = 9.1 )
Turn−Off Delay Time
Fall Time
Total Gate Charge
(VDS = 80 Vdc,
Vd ID = 12 Adc,
Ad
VGS = 10 Vdc)
Gate−to−Source Charge
Gate−to−Drain Charge
ns
tf
−
32
60
Qtot
−
14
20
Qgs
−
3.0
−
Qgd
−
7.0
−
VSD
−
−
0.95
0.80
1.0
−
Vdc
trr
−
85
−
ns
ta
−
60
−
tb
−
28
−
QRR
−
0.3
−
nC
BODY−DRAIN DIODE RATINGS (Note 4)
Diode Forward On−Voltage
(IS = 12 Adc, VGS = 0 Vdc)
(IS = 12 Adc, VGS = 0 Vdc, TJ = 125°C)
Reverse Recovery Time
(IS = 12 Adc,
Ad VGS = 0 Vdc,
Vd
dIS/dt = 100 A/s)
Reverse Recovery Stored Charge
C
4. Indicates Pulse Test: P.W. = 300 s max, Duty Cycle = 2%.
5. Switching characteristics are independent of operating junction temperature.
ORDERING INFORMATION
Device
NTD12N10
Package
Shipping†
DPAK
75 Units/Rail
NTD12N10−1
DPAK−3
75 Units/Rail
NTD12N10T4
DPAK
2500 Tape & Reel
DPAK
(Pb−Free)
2500 Tape & Reel
NTD12N10T4G
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
http://onsemi.com
2
NTD12N10
TYPICAL ELECTRICAL CHARACTERISTICS
24
VGS = 10 V
7V
9V
20
TJ = 25°C
ID, DRAIN CURRENT (AMPS)
ID, DRAIN CURRENT (AMPS)
24
6.5 V
8V
16
6V
7.5 V
12
5.5 V
8
5V
4
VDS ≥ 10 V
20
16
12
8
TJ = 25°C
4
4.5 V
0
0
8
9
1
2
3
4
5
6
7
VDS, DRAIN−TO−SOURCE VOLTAGE (VOLTS)
10
0
1
2
3
4
5
6
7
8
9
VGS, GATE−TO−SOURCE VOLTAGE (VOLTS)
VGS = 10 V
0.4
TJ = 100°C
TJ = 25°C
0.1
TJ = −55°C
0
0
4
8
12
16
ID, DRAIN CURRENT (AMPS)
20
24
RDS(on), DRAIN−TO−SOURCE RESISTANCE ()
0.5
0.2
0.2
TJ = 25°C
0.175
VGS = 10 V
0.15
VGS = 15 V
0.125
0.1
0
Figure 3. On−Resistance versus Drain Current
and Temperature
4
12
16
8
ID, DRAIN CURRENT (AMPS)
20
24
Figure 4. On−Resistance versus Drain Current
and Gate Voltage
3
2.5
10
Figure 2. Transfer Characteristics
10000
VGS = 0 V
ID = 6 A
VGS = 10 V
IDSS, LEAKAGE (nA)
RDS(on), DRAIN−TO−SOURCE RESISTANCE (NORMALIZED)
RDS(on), DRAIN−TO−SOURCE RESISTANCE ()
Figure 1. On−Region Characteristics
0.3
TJ = −55°C
TJ = 100°C
0
2
1.5
1
TJ = 150°C
1000
100
TJ = 100°C
0.5
0
−50 −25
0
25
50
75 100 125
TJ, JUNCTION TEMPERATURE (°C)
150
10
175
20
Figure 5. On−Resistance Variation with
Temperature
40
50
60
70
80
90 100
30
VDS, DRAIN−TO−SOURCE VOLTAGE (VOLTS)
Figure 6. Drain−to−Source Leakage Current
versus Voltage
http://onsemi.com
3
NTD12N10
POWER MOSFET SWITCHING
Switching behavior is most easily modeled and predicted
by recognizing that the power MOSFET is charge
controlled. The lengths of various switching intervals (t)
are determined by how fast the FET input capacitance can
be charged by current from the generator.
The published capacitance data is difficult to use for
calculating rise and fall because drain−gate capacitance
varies greatly with applied voltage. Accordingly, gate
charge data is used. In most cases, a satisfactory estimate
of average input current (IG(AV)) can be made from a
rudimentary analysis of the drive circuit so that
t = Q/IG(AV)
The capacitance (Ciss) is read from the capacitance curve at
a voltage corresponding to the off−state condition when
calculating td(on) and is read at a voltage corresponding to the
on−state when calculating td(off).
At high switching speeds, parasitic circuit elements
complicate the analysis. The inductance of the MOSFET
source lead, inside the package and in the circuit wiring
which is common to both the drain and gate current paths,
produces a voltage at the source which reduces the gate drive
current. The voltage is determined by Ldi/dt, but since di/dt
is a function of drain current, the mathematical solution is
complex. The MOSFET output capacitance also
complicates the mathematics. And finally, MOSFETs have
finite internal gate resistance which effectively adds to the
resistance of the driving source, but the internal resistance
is difficult to measure and, consequently, is not specified.
The resistive switching time variation versus gate
resistance (Figure 9) shows how typical switching
performance is affected by the parasitic circuit elements. If
the parasitics were not present, the slope of the curves would
maintain a value of unity regardless of the switching speed.
The circuit used to obtain the data is constructed to minimize
common inductance in the drain and gate circuit loops and
is believed readily achievable with board mounted
components. Most power electronic loads are inductive; the
data in the figure is taken with a resistive load, which
approximates an optimally snubbed inductive load. Power
MOSFETs may be safely operated into an inductive load;
however, snubbing reduces switching losses.
During the rise and fall time interval when switching a
resistive load, VGS remains virtually constant at a level
known as the plateau voltage, VSGP. Therefore, rise and fall
times may be approximated by the following:
tr = Q2 x RG/(VGG − VGSP)
tf = Q2 x RG/VGSP
where
VGG = the gate drive voltage, which varies from zero to VGG
RG = the gate drive resistance
and Q2 and VGSP are read from the gate charge curve.
During the turn−on and turn−off delay times, gate current
is not constant. The simplest calculation uses appropriate
values from the capacitance curves in a standard equation
for voltage change in an RC network. The equations are:
td(on) = RG Ciss In [VGG/(VGG − VGSP)]
td(off) = RG Ciss In (VGG/VGSP)
1000
VDS = 0 V
TJ = 25°C
Ciss
800
C, CAPACITANCE (pF)
VGS = 0 V
600
Crss
Ciss
400
Coss
200
0
10
Crss
5
0
VGS
5
10
15
20
25
VDS
GATE−TO−SOURCE OR DRAIN−TO−SOURCE VOLTAGE
(VOLTS)
Figure 7. Capacitance Variation
http://onsemi.com
4
18
90
QT
16
80
VDS
14
70
12
60
10
VGS
8
Q1
6
50
40
Q2
30
4
20
ID = 12 A
TJ = 25°C
2
0
0
2
4
6
8
10
QG, TOTAL GATE CHARGE (nC)
10
0
14
12
1000
VDD = 80 V
ID = 12 A
VGS = 10 V
100
t, TIME (ns)
100
20
VDS, DRAIN−TO−SOURCE VOLTAGE (VOLTS)
VGS, GATE−TO−SOURCE VOLTAGE (VOLTS)
NTD12N10
tr
tf
td(off)
td(on)
10
1
1
Figure 8. Gate−To−Source and Drain−To−Source
Voltage versus Total Charge
10
RG, GATE RESISTANCE ()
100
Figure 9. Resistive Switching Time
Variation versus Gate Resistance
DRAIN−TO−SOURCE DIODE CHARACTERISTICS
IS, SOURCE CURRENT (AMPS)
12
VGS = 0 V
TJ = 25°C
10
8
6
4
2
0
0.4
0.5
0.6
0.7
0.8
0.9
VSD, SOURCE−TO−DRAIN VOLTAGE (VOLTS)
1
Figure 10. Diode Forward Voltage versus Current
SAFE OPERATING AREA
The Forward Biased Safe Operating Area curves define
the maximum simultaneous drain−to−source voltage and
drain current that a transistor can handle safely when it is
forward biased. Curves are based upon maximum peak
junction temperature and a case temperature (TC) of 25°C.
Peak repetitive pulsed power limits are determined by using
the thermal response data in conjunction with the procedures
discussed
in
AN569,
“Transient
Thermal
Resistance−General Data and Its Use.”
Switching between the off−state and the on−state may
traverse any load line provided neither rated peak current
(IDM) nor rated voltage (VDSS) is exceeded and the
transition time (tr,tf) do not exceed 10 s. In addition the total
power averaged over a complete switching cycle must not
exceed (TJ(MAX) − TC)/(RJC).
A Power MOSFET designated E−FET can be safely used
in switching circuits with unclamped inductive loads. For
reliable operation, the stored energy from circuit inductance
dissipated in the transistor while in avalanche must be less
than the rated limit and adjusted for operating conditions
differing from those specified. Although industry practice is
to rate in terms of energy, avalanche energy capability is not
a constant. The energy rating decreases non−linearly with an
increase of peak current in avalanche and peak junction
temperature.
Although many E−FETs can withstand the stress of
drain−to−source avalanche at currents up to rated pulsed
current (IDM), the energy rating is specified at rated
continuous current (ID), in accordance with industry
custom. The energy rating must be derated for temperature
as shown in the accompanying graph (Figure 12). Maximum
energy at currents below rated continuous ID can safely be
assumed to equal the values indicated.
http://onsemi.com
5
NTD12N10
ID, DRAIN CURRENT (AMPS)
100
VGS = 20 V
SINGLE PULSE
TC = 25°C
10 s
10
100 s
1 ms
1
10 ms
RDS(on) LIMIT
THERMAL LIMIT
PACKAGE LIMIT
r(t), EFFECTIVE TRANSIENT THERMAL RESISTANCE
(NORMALIZED)
0.1
0.1
dc
10
1
VDS, DRAIN−TO−SOURCE VOLTAGE (VOLTS)
100
EAS, SINGLE PULSE DRAIN−TO−SOURCE
AVALANCHE ENERGY (mJ)
SAFE OPERATING AREA
80
ID = 12 A
60
40
20
0
25
50
75
100
125
175
150
TJ, STARTING JUNCTION TEMPERATURE (°C)
Figure 11. Maximum Rated Forward Biased
Safe Operating Area
Figure 12. Maximum Avalanche Energy versus
Starting Junction Temperature
1.0
D = 0.5
0.2
0.1
0.1
0.05
P(pk)
0.02
0.01
SINGLE PULSE
0.01
0.00001
t1
t2
DUTY CYCLE, D = t1/t2
0.0001
0.001
0.01
t, TIME (s)
RJC(t) = r(t) RJC
D CURVES APPLY FOR POWER
PULSE TRAIN SHOWN
READ TIME AT t1
TJ(pk) − TC = P(pk) RJC(t)
0.1
Figure 13. Thermal Response
di/dt
IS
trr
ta
tb
TIME
0.25 IS
tp
IS
Figure 14. Diode Reverse Recovery Waveform
http://onsemi.com
6
1
10
NTD12N10
PACKAGE DIMENSIONS
DPAK
CASE 369C−01
ISSUE O
−T−
C
B
V
SEATING
PLANE
E
R
4
Z
A
S
1
2
DIM
A
B
C
D
E
F
G
H
J
K
L
R
S
U
V
Z
3
U
K
F
J
L
H
D
G
2 PL
0.13 (0.005)
M
T
INCHES
MIN
MAX
0.235 0.245
0.250 0.265
0.086 0.094
0.027 0.035
0.018 0.023
0.037 0.045
0.180 BSC
0.034 0.040
0.018 0.023
0.102 0.114
0.090 BSC
0.180 0.215
0.025 0.040
0.020
−−−
0.035 0.050
0.155
−−−
STYLE 2:
PIN 1. GATE
2. DRAIN
3. SOURCE
4. DRAIN
SOLDERING FOOTPRINT*
6.20
0.244
3.0
0.118
2.58
0.101
5.80
0.228
1.6
0.063
6.172
0.243
SCALE 3:1
mm inches
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
http://onsemi.com
7
MILLIMETERS
MIN
MAX
5.97
6.22
6.35
6.73
2.19
2.38
0.69
0.88
0.46
0.58
0.94
1.14
4.58 BSC
0.87
1.01
0.46
0.58
2.60
2.89
2.29 BSC
4.57
5.45
0.63
1.01
0.51
−−−
0.89
1.27
3.93
−−−
NTD12N10
PACKAGE DIMENSIONS
DPAK−3
CASE 369D−01
ISSUE B
V
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
C
B
E
R
4
Z
A
S
1
2
3
−T−
SEATING
PLANE
K
J
F
H
D
G
3 PL
0.13 (0.005)
M
DIM
A
B
C
D
E
F
G
H
J
K
R
S
V
Z
INCHES
MIN
MAX
0.235 0.245
0.250 0.265
0.086 0.094
0.027 0.035
0.018 0.023
0.037 0.045
0.090 BSC
0.034 0.040
0.018 0.023
0.350 0.380
0.180 0.215
0.025 0.040
0.035 0.050
0.155
−−−
MILLIMETERS
MIN
MAX
5.97
6.35
6.35
6.73
2.19
2.38
0.69
0.88
0.46
0.58
0.94
1.14
2.29 BSC
0.87
1.01
0.46
0.58
8.89
9.65
4.45
5.45
0.63
1.01
0.89
1.27
3.93
−−−
STYLE 2:
PIN 1. GATE
2. DRAIN
3. SOURCE
4. DRAIN
T
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 61312, Phoenix, Arizona 85082−1312 USA
Phone: 480−829−7710 or 800−344−3860 Toll Free USA/Canada
Fax: 480−829−7709 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
ON Semiconductor Website: http://onsemi.com
Order Literature: http://www.onsemi.com/litorder
Japan: ON Semiconductor, Japan Customer Focus Center
2−9−1 Kamimeguro, Meguro−ku, Tokyo, Japan 153−0051
Phone: 81−3−5773−3850
http://onsemi.com
8
For additional information, please contact your
local Sales Representative.
NTD12N10/D