FBR600 - FBR610 FAST RECOVERY BRIDGE RECTIFIERS PRV : 50 - 1000 Volts Io : 6.0 Amperes BR6 0.445 (11.30) 0.405 (10.30) FEATURES : * * * * * * * High case dielectric strength High surge current capability High reliability Low reverse current Low forward voltage drop Fast switching for high efficiency Ideal for printed circuit board φ0.158 (4.00) AC + 0.142 (3.60) 0.62 (15.75) 0.58 (14.73) 0.127 (3.20) 0.047 (1.20) AC 0.042 (1.06) 0.038 (0.96) MECHANICAL DATA : 0.75 (19.1) Min. * Case : Reliable low cost construction utilizing molded plastic technique * Epoxy : UL94V-O rate flame retardant * Terminals : Plated lead solderable per MIL-STD-202, Method 208 guaranteed * Polarity : Polarity symbols marked on case * Mounting position : Any * Weight : 3.6 grams 0.27 (6.90) 0.23 (5.80) Dimension in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Rating at 25 °C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20%. Maximum Recurrent Peak Reverse Voltage VRRM FBR 600 50 Maximum RMS Voltage V RMS 35 70 140 280 420 560 700 Volts Maximum DC Blocking Voltage VDC 50 100 200 400 600 800 1000 Volts Maximum Average Forward Current Tc = 50 °C I F(AV) 6.0 Amps. I FSM 150 Amps. 2 64 RATING SYMBOL FBR 601 100 FBR 602 200 FBR 604 400 FBR 606 600 FBR 608 800 FBR 610 1000 UNIT Volts Peak Forward Surge Current Single half sine wave Superimposed on rated load (JEDEC Method) Current Squared Time at t < 8.3 ms. Maximum Forward Voltage drop per Diode at I F = 3.0 Amps. Maximum DC Reverse Current Ta = 25 °C at Rated DC Blocking Voltage Ta = 100 °C Maximum Reverse Recovery Time (Note 1) Typical Thermal Resistance per diode (Note 2) Operating Junction Temperature Range Storage Temperature Range It VF 2 IR 10 A S Volts µA I R(H) 1.0 mA Trr 1.3 150 250 500 ns RθJC 8 TJ - 50 to + 150 °C/W °C TSTG - 50 to + 150 °C Notes : 1 ) Measured with IF = 0.5 Amp., IR = 1 Amp., Irr = 0.25 Amp. 2 ) Thermal resistance from Junction to Case with units mounted on a 6" x 5.5" x0.11" ( 15 x 14 x 0.3 cm ) Al. plate. UPDATE : APRIL 21, 1998 RATING AND CHARACTERISTIC CURVES ( FBR600 - FBR610 ) FIG.1 - REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM 50 Ω Trr 10 Ω + 0.5 D.U.T. + 0 PULSE GENERATOR ( NOTE 2 ) 50 Vdc (approx) 1Ω - 0.25 OSCILLOSCOPE ( NOTE 1 ) - 1.0 A SET TIME BASE FOR 50/100 ns/cm NOTES : 1. Rise Time = 7 ns max., Input Impedance = 1 megaohm, 22 pF. 1 2. Rise time = 10 ns max., Source Impedance = 50 ohms. 3. All Resistors = Non-inductive Types. FIG.2 - DERATING CURVE FOR OUTPUT RECTIFIED CURRENT FIG.3 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 150 PEAK FORWARD SURGE CURRENT, AMPERES AVERAGE FORWARD OUTPUT CURRENT, AMPERES 6.0 4.8 3.6 2.4 1.2 Tc = 55 °C 120 90 60 30 60Hz RESISTIVE OR INDUCTIVE LOAD 0 0 25 50 75 100 125 150 0 175 1 CASE TEMPERATURE, ( °C) 2 4 6 FIG.4 - TYPICAL FORWARD CHARACTERISTICS 20 40 60 PER DIODE PER DIODE 10 TJ = 100 °C REVERSE CURRENT, MICROAMPERES Pulse Width = 300 µ s 2% Duty Cycle TJ = 25 °C 10 1.0 0.1 1.0 0.1 TJ = 25 °C 0.01 0 20 40 60 80 100 120 PERCENT OF RATED REVERSE VOLTAGE, (%) 0.01 0 100 FIG.5 - TYPICAL REVERSE CHARACTERISTICS 100 FORWARD CURRENT, AMPERES 10 NUMBER OF CYCLES AT 60Hz 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 FORWARD VOLTAGE, VOLTS 1.8 2.0 140