FUJITSU MEDIA DEVICE DATA SHEET DS04-23116-2E ASSP Mobile Communication Systems SAW Duplexer (700 to 1000 MHz) D5CC Series (D1) ■ DESCRIPTION The D5CC series of SAW antenna duplexer apply to the frequency range 700 to 1000 MHz. The SAW filters are fabricated on a piezoelectric-crystal unit (LiTaO3:lithium tantalate) with a large electromechanical dissociation. The D5CC series provides small size and light duplexer by using original design, mounting and electrode formation techniques. D5CC(D1) series are incorporated transmitter filter and receiver filter into a small package and are housed phase circuit in the package. Moreover, I/O of SAW filter is set to impedance 50 Ω, so application requires no external circuits. ■ FEATURES • • • • Ultra compact and light package (0.14cm3, 9.5 × 7.5 × 2.0 (h) mm Typ.) External matching circuits are not required. Surface mount package (SMT) High handling power resistance (1.2 W Max.) ■ PACKAGE D5CC Series (D1) ■ PIN ASSIGNMENT (TOP VIEW) 12 11 10 9 8 13 7 C8 B 01 F 14 15 16 1 2 6 5 3 4 3 4 (BOTTOM VIEW) 16 2 15 5 14 6 13 7 12 2 1 11 10 9 8 D5CC Series (D1) ■ PIN DESCRIPTION Pin No. Pin name Description 1 GND Ground Pin 2 ANT Antenna Pin* 3 GND Ground Pin 4 GND Ground Pin 5 GND Ground Pin 6 Rx 7 GND Ground Pin 8 GND Ground Pin 9 GND Ground Pin 10 ANT Antenna Pin* 11 GND Ground Pin 12 GND Ground Pin 13 GND Ground Pin 14 Tx 15 GND Ground Pin 16 GND Ground Pin Receiver side Pin Transmitter side Pin * : Only one Antenna pin should be connected. The remaining Antenna pin doesnot have to be connected. 3 D5CC Series (D1) ■ ABSOLUTE MAXIMUM RATINGS Parameter Rating Symbol Unit Min. Max. Ta −30 +85 °C Tstg −40 +100 °C Maximum input power PIN 1.2 W Input DC voltage −5 +5 V Operating temperature Storage temperature WARNING: Piezoelectric devices can be permanently damaged by application of stress (voltage, current, temperature, etc.) in excess of absolute maximum ratings. Do not exceed these ratings. ■ RECOMMENDED OPERATING CONDITIONS Parameter Symbol Operating temperature Ta Value Min. Max. −30 +85 Unit °C WARNING: The recommended operating conditions are required in order to ensure the normal operation of the piezoelectric device. All of the device’s electrical characteristics are warranted when the device is operated within these ranges. Always use piezoelectric devices within their recommended operating condition ranges. Operation outside these ranges may adversely affect reliability and could result in device failure. No warranty is made with respect to uses, operating conditions, or combinations not represented on the data sheet. Users considering application outside the listed conditions are advised to contact their FUJITSU representatives beforehand. ■ STANDARD FREQUENCIES System AMPS/IS-95/IS-136 4 Tx freq. (MHz) Rx freq. (MHz) Part number Part symbol 824 to 849 869 to 894 FAR-D5CC-881M50-D1C8 C8 Remarks D5CC Series (D1) ■ ELECTRICAL CHARACTERISTICS AMPS/IS-136/IS-95 1. Part number : FAR-D5CC-881M50-D1C8 Parameter Tx → Antenna Unit Remarks Min. Typ. Max. 2.0 2.5 dB +15 to +35 °C 2.7 dB −30 to +85 °C 824 to 849 MHz Inband Ripple 824 to 849 MHz 1.0 1.5 dB VSWR (Return loss) 842 to 849 MHz (7.4) 1.8 (10.9) 2.5 () (dB) 779 to 804 MHz 12 17 dB 869 to 894 MHz 40 46 dB 1648 to 1698 MHz 6 9 dB 2472 to 2547 MHz 6 8 dB Insertion Loss 869 to 894 MHz 3.8 4.3 dB Inband Ripple 869 to 894 MHz 1.5 2.5 dB VSWR (Return loss) 869 to 894 MHz (6.8) 2.3 (8.1) 2.7 () (dB) 824 to 849 MHz 50 55 dB 930 to 1200 MHz 40 43 dB 1200 to 1500 MHz 40 43 dB 1500 to 1800MHz 40 45 dB 824 to 849 MHz 53 55 dB 46 49 dB +15 to +85 °C 43 dB −30 to +15 °C Absolute Attenuation Tx → Rx Value Insertion Loss Absolute Attenuation Antenna → Rx Condition (Ta = −30 °C to +85 °C) Absolute Attenuation (Isolation) Maximum Input Power 869 to 894 MHz Ta = +50 °C 1.2 W (continuous wave > 50000 h) 5 D5CC Series (D1) • Typical Characteristics S21 log MAG 1 10 dB/ REF 0 dB TX 2 3 1 : −1.9803 dB 824 MHz 2 : −1.7331 dB 849 MHz 3 : −61.585 dB 869 MHz 4 : −47.689 dB 894 MHz 4 RX 1 : −62.318 dB 824 MHz 2 : −57.892 dB 849 MHz 3 : −3.3498 dB 869 MHz 4 : −3.3633 dB 894 MHz 4 1 2 3 TX RX START 760 MHz S21 STOP 960 MHz log MAG 10 dB/ REF 0 dB TX→RX Isolation 1 : −59.654 dB 824 MHz 2 : −68.072 dB 849 MHz 3 : −53.411 dB 869 MHz 4 : −54.842 dB 894 MHz 1 3 4 2 START 760 MHz 6 STOP 960 MHz D5CC Series (D1) S21 log MAG 1 5 dB/ REF 0 dB 1 5 3 4 2 5 4 3 RX 1 : −2.5972 dB 881.5 MHz 2 : −40.83 dB 1 GHz 3 : −47.85 dB 1.5 GHz 4 : −37.591 dB 2 GHz 5 : −32.402 dB 2.5 GHz TX RX 2 START .030 MHz TX 1 : −1.564 dB 836.5 MHz 2 : −10.596 dB 1.648 GHz 3 : −9.3088 dB 1.698 GHz 4 : −10.209 dB 2.472 GHz 5 : −7.4124 dB 2.547 GHz STOP 3 000.000 MHz 7 D5CC Series (D1) ■ MEASURMENT CIRCUIT (1) Tx → ANT (2) ANT → Rx ANT ANT 10 2 50 Ω Tx 14 6 1 3 4 9 11 12 6 5 7 8 13 15 16 2 50 Ω Rx 14 1 3 4 9 11 12 Open 10 5 7 8 13 15 16 Open (3)Tx → Rx 50 Ω 10 Tx RX 14 6 1 3 4 9 11 12 5 7 8 13 15 16 2 Open ■ PART NUMBER DESIGNATION [Designation example] FAR-D5CC- -D1 (1) (2) (3) (1) Frequency : Specify the nominal center frequency of higher frequency side in six alphanumeric. Enter M (for MHz) at the decimal point. Refer to below example. [Example] 881.5 MHz → 881M50 (2) Part symbol : Specified characters from A1 to Z9. (3) Packing : T : 1 k pcs/reel Q : 2 k pcs/reel 8 D5CC Series (D1) ■ MARKING Logo C8 B 01 F Data (EIAJ standard) Part Symbol Lot Number Index 9 D5CC Series (D1) ■ PACKAGE DIMENSION 9.5 C8 B 01 7.5 F 2.2 Max. 16 − R0.2 4.75 0.8 2.54 0.6 1.27 4.6 3.75 1.1 0.8 0.8 6.8 Dimensions in mm. 10 D5CC Series (D1) ■ RECOMMENDED LAND PATTERN 0.8 1.27 3.75 7.5 1.0 0.3 4 - C 0.3 0.8 1.0 2.54 0.3 2.54 4.75 9.5 Dimensions in mm. Note : Only one Antenna pin should be connected. The remaining Antenna pin does not have to be connected. 11 D5CC Series (D1) ■ PACKING : Reel type (1) Reel Dimensions 16.4 ± 2.0 0.0 2 ± 0.5 φ21 ± 0.8 φ330 φ80 φ13.0 ± 0.2 Type A Volume -T φ330 1 k pcs -Q φ330 2 k pcs R1.0 22.4 Max. Dimensions in mm. (2) Packing Style Reel side Pulling side Pulling side Index 12 D5CC Series (D1) φ1.5 ± 0.1 0 0.3 10.0 ± 0.1 7.5 ± 0.1 2.0 ± 0.1 12.0 ± 0.1 8.0 ± 0.1 16.0 ± 0.3 4.0 ± 0.1 1.75 ± 0.1 (3) Tape Dimensions 2.5 ± 0.1 φ1.6 Dimensions in mm. (4) Peel strength of top cover tape Peel off by the force of 0.1 N to 0.7 N under the condition at the right. (Conforms to JIS C 0806 section 5.2) Direction of pulling Speed 300 mm/min 165 to 185 ° Embossment carrier type tape 13 D5CC Series (D1) ■ RECOMMENDED REFLOW PROFILE 240 Temperature (°C) 10 s Heating rate 1 to 4 °C/s 210 Air cooling 60 s Pre-Heating 150 60 to 90 s Time (s) ■ NOTE Mass-produced product order is accepted by a unit of 1000. 14 D5CC Series (D1) FUJITSU MEDIA DEVICES LIMITED For further information please contact: Japan FUJITSU MEDIA DEVICES LIMITED International Sales and Marketing Dept. Sin-Yokohama Square Bldg.,14F, Shin-Yokohama 2-3-12, Kouhoku-ku, Yokohama-shi, Kanagawa 222-0033, Japan Tel: +81-45-471-0061 Fax: +81-45-471-0076 http://www.fujitsu.co.jp/hypertext/fmd/English/index.html North and South America FUJITSU MICROELECTRONICS, INC. 3545 North First Street, San Jose, CA 95134-1804, U.S.A. Tel: +1-408-922-9000 Fax: +1-408-922-9179 Customer Response Center Mon. - Fri.: 7 am - 5 pm (PST) Tel: +1-800-866-8608 Fax: +1-408-922-9179 http://www.fujitsumicro.com/ Europe FUJITSU MICROELECTRONICS EUROPE GmbH Am Siebenstein 6-10, D-63303 Dreieich-Buchschlag, Germany Tel: +49-6103-690-0 Fax: +49-6103-690-122 http://www.fujitsu-fme.com/ All Rights Reserved. The contents of this document are subject to change without notice. Customers are advised to consult with FUJITSU sales representatives before ordering. The information and circuit diagrams in this document are presented as examples of semiconductor device applications, and are not intended to be incorporated in devices for actual use. Also, FUJITSU is unable to assume responsibility for infringement of any patent rights or other rights of third parties arising from the use of this information or circuit diagrams. The contents of this document may not be reproduced or copied without the permission of FUJITSU LIMITED. FUJITSU semiconductor devices are intended for use in standard applications (computers, office automation and other office equipments, industrial, communications, and measurement equipments, personal or household devices, etc.). CAUTION: Customers considering the use of our products in special applications where failure or abnormal operation may directly affect human lives or cause physical injury or property damage, or where extremely high levels of reliability are demanded (such as aerospace systems, atomic energy controls, sea floor repeaters, vehicle operating controls, medical devices for life support, etc.) are requested to consult with FUJITSU sales representatives before such use. The company will not be responsible for damages arising from such use without prior approval. Asia Pacific FUJITSU MICROELECTRONICS ASIA PTE. LTD. #05-08, 151 Lorong Chuan, New Tech Park, Singapore 556741 Tel: +65-281-0770 Fax: +65-281-0220 http://www.fmap.com.sg/ F0010 FUJITSU LIMITED Printed in Japan Any semiconductor devices have inherently a certain rate of failure. You must protect against injury, damage or loss from such failures by incorporating safety design measures into your facility and equipment such as redundancy, fire protection, and prevention of over-current levels and other abnormal operating conditions. If any products described in this document represent goods or technologies subject to certain restrictions on export under the Foreign Exchange and Foreign Trade Control Law of Japan, the prior authorization by Japanese government should be required for export of those products from Japan.