1.25mm Pitch Super Low profile Crimping Connector DF14 Series ■Features 1. Super Low Profile This is a connector special for right angle which has pursued a low profile on the board. Board mounting height: 2.5mm A signal can be fetched from the area where there is no board to board space. Board Mounting Figure 2. Correspond to Automatic Mounting The header has the vacuum mount face which enables the vacuum absorption and the automatic mounting by the embossed tape packaging.In addition, the tube packaging can be selected. 3. Four Wall Type Without Friction to Board by Socket The header has the box structure to prevent from being twisted and has the perfect mis-insertion prevention method. Moreover the header has the wall on the board side and doesn't have any trouble resulted from the friction to board by socket. In addition, the metal fitting is attached to prevent the solder peel. 1 ■Applications LCD, Note PC, Mobile Terminal Small business equipment, Video camera B177 ■Product Specifications Current rating Rating 1A Operating Temperature Range-25 to +85ç (Note 1) Voltage rating 150V AC Operating Moisture Range Item Storage Temperature Range -10 to +60ç (Note 2) 40 to 80% Storage Moisture Range Specification 40 to 70% Condition 1. Insulation Resistance 500M ohms Min 100V DC 2. Withstanding voltage No flashover or insulation breakdown. 500V AC/1 minute 3. Contact Resistance 30m ohms Max 100mA 4. Insertion/Extraction Force MIN0.15N (15gf), MAX3N (300gf) Measure at the square steel pin of 0.3±0.002mm 5. Vibration Frequency: 10 to 55 Hz, single amplitude of 0.75 mm, 2 hours in each of the 3 directions. No electrical discontinuity of 1µs or more 6. Humidity (Steady state) Contact resistance: 30m ohms Max Insulation resistance:500M ohms Min 7. Temperature Cycle 96 hours at temperature of 40ç and humidity of 90% to 95% (-25ç: 30 minutes➝5 to 35ç: 10 minutes➝85ç: 30 minutes➝ Contact resistance: 30m ohms Max Insulation resistance: 500M ohms Min 5 to 35ç: 10 minutes) 5 cycles 8. Durability (Mating/un-mating) Contact resistance: 30m ohms Max 9. Resistance to Soldering heat Tin plating: 30 cycles Gold plating: 50 cycles Reflow: At the recommended temperature profile No deformation of components affecting performance. Manual soldering: 300ç for 3 seconds Note 1: Includes temperature rise caused by current flow. Note 2: The term "storage" refers to products stored for long period of time prior to mounting and use. Operating Temperature Range and Humidity range covers non conducting condition of installed connectors in storage, shipment or during transportation. ■Material Product Part Crimping Socket Insulator Crimping Contact for Socket Contact Insulator Contact Fitting Pin Header Material Finish Remarks Polyamide Beige UL-94V-0 Phosphor Copper Tin-lead plated or gold plated ––––––– Polyamide Beige UL-94V-0 Brass Tin-lead plated or gold plated ––––––– Phosphor copper Tin-lead plated ––––––– Note . Hirose’s tin plating product takes measures against whisker. ■Ordering Information ●Connector DF14 1 - * S - 1.25 C 2 3 4 5 1 Series Name: DF14 4 Contact Pitch: 1.25mm 2 Number of Contacts: 2 to 10, 15, 20, 25, 30 5 Contact Type 3 Connector Type C: Crimping socket S: Single row socket H: Right angle SMT P: Single row pin header ●Contact DF14 - 2628 SCF A 1 1 Applicable cable size 2 2 2628: AWG26 to 28 3032: AWG30 to 32 3 Packaging Type SCF: Socket contact/reel 3 Plating Type Blank: Tin plated A: Gold plated B178 ■Crimping Socket Photo: Contact insertion state Unit: mm Part Number DF14- 2S-1.25C(**) DF14- 3S-1.25C(**) DF14- 4S-1.25C(**) DF14- 5S-1.25C(**) DF14- 6S-1.25C(**) DF14- 7S-1.25C(**) DF14- 8S-1.25C(**) DF14- 9S-1.25C(**) DF14-10S-1.25C(**) DF14-15S-1.25C(**) DF14-20S-1.25C(**) DF14-25S-1.25C(**) DF14-30S-1.25C(**) CL No. 538-0005-8-** 538-0006-0-** 538-0007-3-** 538-0008-6-** 538-0009-9-** 538-0010-8-** 538-0011-0-** 538-0013-6-** 538-0014-9-** 538-0054-3-** 538-0059-7-** 538-0064-7-** 538-0012-3-** Number of Contacts 2 3 4 5 6 7 8 9 10 15 20 25 30 A 4.45 5.70 6.95 8.20 9.45 10.70 11.95 13.20 14.45 20.70 26.95 33.20 39.45 B 1.25 2.50 3.75 5.00 6.25 7.50 8.75 10.00 11.25 17.50 23.75 30.00 36.25 [Specific No.]–**,(**) Blank : 1 bag 100 pcs. Note 1.The quantity at the specific No. "Blank" is delivered per bag. If needed, please order the products per bag. ■Socket Crimping Contact Part Number DF14-2628SCF DF14-3032SCF CL No. 538-0001-7-** 538-0003-2-** Packaging Type Reel Reel KApplicable Cable (Tin plating Annealed copper wire) Conductor Size (Wire construction) AWG26(7 cores/0.16mm) AWG28(7 cores/0.127mm) AWG30(7 cores/0.1mm) AWG32(7 cores/0.08mm) Jacket Diameter Ø0.54 to Ø1mm Quantity Finish 10,000 Tin plated KRecommended Cable UL1571 KStrip Length 1.2 to 1.9mm Note:If other cables are used instead of the applicable cable, contact Hirose sales department. BApplicable Crimping Tool Type Applicator Press Main Unit Manual Crimping Tool Part Number AP105-DF14-2628S AP105-DF14-3032S CM-105 DF14-2628/CR-HT DF14-3032/CR-HT CL No. 901-4548-1 901-4544-0 901-0005-4 550-0261-1 550-0262-4 Applicable Contact DF14-2628SCF/SCFA DF14-3032SCF/SCFA --------------------------------------------DF14-2628SCF/SCFA DF14-3032SCF/SCFA Note 1.If a trouble has occurred due to tools, which are not designated by Hirose, Hirose won't guarantee any product. Note 2.Use the reel contact sequentially cut for manual crimping tool. B179 ■Right Angle Pin Header (SMT) Note 1."Without boss" indicates the style with no boss. BPCB mounting pattern BTube Packaging Dimensions [Specific No.]–**,(**) (20): Tin plated tube packaging (21): Tin plated embossed tape packaging (50): Gold plated tube packaging (59): Gold plated embossed tape packaging Note 2."Without boss" indicates that no hole is needed. Unit: mm With boss Part Number Without boss CL No. Part Number Tube Packaging CL No. Number of Contacts A B C D DF14- 2P-1.25H(**) 538-0021-4-** DF14A- 2P-1.25H(**) 538-0033-3-** 2 7.45 1.25 6.45 8.05 66 DF14- 3P-1.25H(**) 538-0022-7-** DF14A- 3P-1.25H(**) 538-0034-6-** 3 8.70 2.50 7.70 9.30 56 DF14- 4P-1.25H(**) 538-0023-0-** DF14A- 4P-1.25H(**) 538-0035-9-** 4 9.95 3.75 8.95 10.55 49 DF14- 5P-1.25H(**) 538-0024-2-** DF14A- 5P-1.25H(**) 538-0036-1-** 5 11.20 5.00 10.20 11.80 44 DF14- 6P-1.25H(**) 538-0025-5-** DF14A- 6P-1.25H(**) 538-0037-4-** 6 12.45 6.25 11.45 13.05 39 DF14- 7P-1.25H(**) 538-0026-8-** DF14A- 7P-1.25H(**) 538-0038-7-** 7 13.70 7.50 12.70 14.30 36 DF14- 8P-1.25H(**) 538-0027-0-** DF14A- 8P-1.25H(**) 538-0039-0-** 8 14.95 8.75 13.95 15.55 32 DF14- 9P-1.25H(**) 538-0028-3-** DF14A- 9P-1.25H(**) 538-0040-9-** 9 16.20 10.00 15.20 16.80 30 DF14-10P-1.25H(**) 538-0029-6-** DF14A-10P-1.25H(**) 538-0041-1-** 10 17.45 11.25 16.45 18.05 28 DF14-15P-1.25H(**) 538-0084-4-** DF14A-15P-1.25H(**) 538-0114-3-** 15 23.70 17.50 22.70 24.30 20 DF14-20P-1.25H(**) 538-0089-8-** DF14A-20P-1.25H(**) 538-0119-7-** 20 29.95 23.75 28.95 30.55 16 DF14-25P-1.25H(**) 538-0094-8-** DF14A-25P-1.25H(**) 538-0124-7-** 25 36.20 30.00 35.20 36.80 13 DF14-30P-1.25H(**) 538-0020-1-** DF14A-30P-1.25H(**) 538-0045-2-** 30 42.45 36.25 41.45 43.05 11 Note 1.Please order the tube packaging product, multiplying the packaging quantity (pcs.). Note 2.Please order the embossed tape packaging product according to reel number. (1000 pcs./reel) B180 Quantity BEmbossed Carrier Tape Dimensions ■ 2 to 10 Contacts ■ 15, 20, 25, 30 Contacts Unit: mm Inserted Connector Number of Contacts A B C D DF14/14A- 2P-1.25H 2 16 7.5 16.4 – – – DF14/14A- 3P-1.25H 3 16 7.5 16.4 – – – DF14/14A- 4P-1.25H 4 24 11.5 24.4 – – – DF14/14A- 5P-1.25H 5 24 11.5 24.4 – – – DF14/14A- 6P-1.25H 6 24 11.5 24.4 – – – DF14/14A- 7P-1.25H 7 24 11.5 24.4 – – – DF14/14A- 8P-1.25H 8 24 11.5 24.4 – – – DF14/14A- 9P-1.25H 9 24 11.5 24.4 – – – DF14/14A-10P-1.25H 10 24 11.5 24.4 – – – DF14/14A-15P-1.25H 15 44 20.2 44.4 40.4 DF14/14A-20P-1.25H 20 44 20.2 44.4 40.4 DF14/14A-25P-1.25H 25 56 26.2 56.4 52.4 DF14/14A-30P-1.25H 30 56 26.2 56.4 52.4 B181 BPrecautions 1. Recommended Temperature Profile (SMT) Note 1.The soldering process is allowed up to twice under the same condition. However, the interval between the first and second processes must be maintained at the room temperature. Note 1.The temperature indicates the board surface temperature on the connector lead area. 2. Recommended Manual Soldering Condition (SMT) Manual soldering: 290ç for 2 seconds 3. Recommended Screen Thickness (SMT) 0.15 to 0.2mm 4. Board Sled (SMT) Max 0.03mm at the connector center area, based on both connector edges 5. Cleaning Condition Refer to Nylon Connector Use Hand book. 6. Connection Condition Refer to Nylon Connector Use Hand book. ■Be careful to carry out the crimping operation according to the "Crimping Condition Sheet" and "Crimping Quality Reference", because the crimping contact style is too small. 7. Cautions ■Be careful for an excessive scoop insertion/extraction, which will cause damage to the product. B182