CTS1, CTS13, CTS32, 749DX Vishay Sprague Hermetically Sealed, Axial-Lead, To CECC Specifications FEATURES • Hermetically sealed metal case with plastic film insulation • Extended capacitance range (type 749DX) • High operational stability with both time and temperature • Low leakage current • Low dissipation factor • Capability to withstand high inrush currents (type CTS32) APPLICATIONS Performance and reliability has been proven in a wide range of applications such as: filtering, by-pass, coupling, energy storage, timing circuits. PERFORMANCE CHARACTERISTICS SPECIFICATIONS Operating Temperature: - 55°C to + 85°C (types CTS13, CTS32) - 55°C to + 125°C (types CTS1, 749DX) CECC 30201-001 30201-002 30201-005 30201-011/012 30201-019 30201-029 749DX CTS1 CTS13 749DX CTS32 749DX BS 9073-N001 749DX IECQ 300201/FR001 CTS1 ORDERING INFORMATION CTS13 TYPE 040 X0 CAPACITANCE DC VOLTAGE RATING @ + 85°C TOLERANCE 105 CAPACITANCE Expressed in picofarads. X0 = ± 20% First two digits are significant. X9 = ± 10% Third digit is the number of X5 = ± 5% zeros following. (Special Order) Expressed in volts. Where necessary, zeros precede the voltage rating to complete the 3 digit block 6R3 = 6.3 Volts 2 A P CASE CODE STYLE NUMBER PACKAGING See Table Ratings and Case Codes. 0 = Bare Case 2 = Plastic-Film Insulation See Taping and Packaging Identifies the Basic Capacitor Design CTS1 = CECC 30201-002 CTS13 = CECC 30201-005 CTS32 = CECC 30201-019 749DX = CECC 30201-001/011/012/029 DIMENSIONS in millimeters 30 MIN. L MAX. 30 MIN.* D MAX. ød *23mm MAX. FOR TAPED CAPACITORS CASE CODE BS D MAX. NF D MAX. L MAX. + 10% Ød - 0.05 A 3.6 3.8 10.2 0.5 B 4.9 5.1 15.0 0.5 C 7.5 7.7 20.5 0.6 D 9.1 9.3 24.0 0.6 www.vishay.com 44 For technical questions, contact [email protected] Document Number 42073 Revision 28-Mar-02 CTS1, CTS13, CTS32, 749DX Hermetically Sealed, Axial-Lead, To CECC Specifications Vishay Sprague TYPE CTS1: STANDARD RATINGS AND CASE CODES RATED VOLTAGE UR (+ 85°C) CR 6.3V 10V 16V 25V 40V 50V 63V 80V 100V 125V CATEGORY VOLTAGE UC (+125°C) mF 40V 50V 67V 82V 0.10 4V 6.3V 10V 13V 25V 33V A A A A 0.12 A A A A 0.15 A A A A 0.18 A A A A 0.22 A A A A 0.27 A A A A A 0.33 A A A A A 0.39 A A A A B 0.47 A A A A A B 0.56 A A A A A B 0.68 A A A A B B 0.82 A A B B B B 1.0 A A B B B B 1.2 1.5 A A B B B B B B B B B B B 1.8 A B B B B B B 2.2 A B B B B B B 2.7 A B B B B B 3.3 A B B B B C 3.9 A B B B B C 4.7 A B B C C C 5.6 A B C C C C 6.8 A B C C C C 8.2 B C C C C 10 B C C C C 12 B C C D D 15 B C C D D 18 B C C D C D 22 B 27 B 33 B C D C D 39 B C D 47 B C D 56 B 68 C D C D 82 C D 100 C D 120 C 150 C 180 D D D 220 D 270 D 330 D Preferred ratings are in bold characters. Non-preferred ratings are available only with a capacitance tolerance of ± 10% or ± 5% (special order). Document Number 42073 Revision 28-Mar-02 For technical questions, contact [email protected] www.vishay.com 45 CTS1, CTS13, CTS32, 749DX Hermetically Sealed, Axial-Lead, To CECC Specifications Vishay Sprague TYPE CTS13: STANDARD RATINGS AND CASE CODES RATED VOLTAGE UR (+ 85°C) CR µF 40V 50V 63V 0.10 6.3V 10V 16V 20V 25V A A A 0.12 A A A 0.15 A A A 0.18 A A A 0.22 A A A 0.27 A A A 0.33 A A A 0.39 A A A 0.47 A A A 0.56 A A A 0.68 A A A 0.82 A A B 1.0 A A B A A B B A B 1.2 1.5 B B 1.8 A B B B 2.2 A B B B 2.7 A B B B 3.3 A B B B 3.9 A B B B 4.7 A B B C 5.6 A B C C 6.8 A B C C B C C C B 8.2 10 C C C 12 B C C D 15 B C C D D 18 B C C 22 B C D 27 B 33 C B C D D 39 B C D 47 B C D 56 B C 68 D C 82 C 100 C D 120 C D 150 C D 180 D D D 220 D 270 D 330 D Preferred ratings are in bold characters. Non-preferred ratings are available only with a capacitance tolerance of ± 10% or ± 5% (special order). www.vishay.com 46 For technical questions, contact [email protected] Document Number 42073 Revision 28-Mar-02 CTS1, CTS13, CTS32, 749DX Hermetically Sealed, Axial-Lead, To CECC Specifications Vishay Sprague CTS32 STANDARD RATINGS AND CASE CODES RATED VOLTAGE UR (+85°C) CR µF 6.3V 10V 16V 25V 1.0 40V 50V 63V A A B 1.2 A A B B 1.5 A B B B 1.8 A B B B 2.2 A B B B 2.7 A B B B 3.3 A B B B 3.9 A B B B 4.7 A B B C 5.6 A B C C 6.8 A B C C 8.2 B C C C 10 B C C C 12 B C C D 15 B C C D 18 B C C D 22 B C D 27 B C D 33 B C D 39 B C D 47 B C D 56 B C D C D 68 82 C D 100 C D 120 C D 150 C D 180 D 220 D 270 D 330 D Preferred ratings are in bold caracters.Non-preferred ratings are available only with a capacitance tolerance of ± 10 % or ± 5 % (special order). Document Number 42073 Revision 28-Mar-02 For technical questions, contact [email protected] www.vishay.com 47 CTS1, CTS13, CTS32, 749DX Hermetically Sealed, Axial-Lead, To CECC Specifications Vishay Sprague TYPE 749DX: STANDARD RATINGS AND CASE CODES RATED VOLTAGE UR (+ 85°C) CR 6.3V 10V µF 16V 20V 25V 35V 40V 50V 63V 25V 33V 40V CATEGORY VOLTAGE UC (+ 125°C) 4V 6.3V 10V 13V 16V 23V 0.068 A 0.085 A 0.10 A A 0.12 A A A A 0.15 A A A 0.18 A A A 0.22 A A A 0.27 A A A 0.33 A A A 0.39 A A A 0.47 A A A 0.56 A A A 0.68 A A 0.82 A A A B 1.0 A A A B A 1.2 A B B B B 1.5 A B B B B 1.8 A B B B B 2.2 A B B B B 2.7 A B B B B 3.3 A B B B B 3.9 A B B B B 4.7 A B B * C 5.6 A B B C C 6.8 A * * C C 8.2 B C C C C 10 B C C C C 12 B C C C D 15 B C C C D D 18 B C C C 22 B C C D 27 B C D D 33 B C D D 39 B C D D C D 47 B 56 B 68 C D C D 82 C D 100 C D 120 C 150 C 180 C 220 * D D D D 270 D 330 D *See extended range page www.vishay.com 48 For technical questions, contact [email protected] Document Number 42073 Revision 28-Mar-02 CTS1, CTS13, CTS32, 749DX Hermetically Sealed, Axial-Lead, To CECC Specifications Vishay Sprague TYPE 749DX: EXTENDED RATINGS AND CASE CODES RATED VOLTAGE UR (+85°C) CR 6.3V 10V 25V 35V 50V 16V 23V 32V 1.2 A A 1.5 A A 1.8 A µF 16V 20V CATEGORY VOLTAGE UC (+125°C) 4V 6.3V 10V 13V 2.2 A 2.7 A 3.3 A 3.9 A A 4.7 A A 5.6 A 6.8 A 8.2 B B B A 10 B A 12 A B 15 A B 18 B 22 B B C 27 B C D 33 B C D 39 B C D 47 B C 56 B C D 68 B C D 82 B D 100 B C C D 120 B C C D 150 C 180 C D D 220 C D 270 C D D 330 C D 390 C D 470 C 560 D D D 680 D 820 D 1000 D Preferred ratings are in bold caracters.Non-preferred ratings are available only with a capacitance tolerance of ± 10 % or ± 5 % (special order). Document Number 42073 Revision 28-Mar-02 For technical questions, contact [email protected] www.vishay.com 49 CTS1, CTS13, CTS32, 749DX Hermetically Sealed, Axial-Lead, To CECC Specifications Vishay Sprague TYPICAL CURVES RIPPLE VOLTAGE @ + 25°C 100 10 5 4 3 2 100 50 40 30 20 100V & 125V 80V 50V & 63V 35V & 40V 20V & 25V 16V 10V 6.3V VOLTS RMS VOLTS RMS 50 40 30 20 1 0.5 0.4 0.3 0.2 0.1 10 100 1K 10K 100K 5 4 3 2 5 4 3 2 1 0.5 0.4 0.3 0.2 0.1 10 1M 100 1K 10K FREQUENCY IN HERTZ Case A Capacitors Case B Capacitors 100K 1M 100K 1M 100 50 40 30 20 100V & 125V 80V 50V & 63V 35V & 40V 20V & 25V 16V 10V 6.3V VOLTS RMS VOLTS RMS 10 10 FREQUENCY IN HERTZ 100 50 40 30 20 100V & 125V 80V 50V & 63V 35V & 40V 20V & 25V 16V 10V 6.3V 1 0.5 0.4 0.3 0.2 0.1 10 www.vishay.com 50 100 1K 10K 100K 1M 10 5 4 3 2 100V & 125V 80V 50V & 63V 35V & 40V 20V & 25V 16V 10V 6.3V 1 0.5 0.4 0.3 0.2 0.1 10 100 1K 10K FREQUENCY IN HERTZ FREQUENCY IN HERTZ Case C Capacitors Case D Capacitors For technical questions, contact [email protected] Document Number 42073 Revision 28-Mar-02 CTS1, CTS13, CTS32, 749DX Hermetically Sealed, Axial-Lead, To CECC Specifications Vishay Sprague PERFORMANCE CHARACTERISTICS 1. Operating Temperature: - 55°C to + 85°C with rated DC voltage UR applied.+ 85°C to + 125°C with linear voltage derating to category voltage UC (only for types CTS1, 749DX) 2. Capacitance and Tolerance: Capacitance measured at 100Hz and + 25°C shall be within the specified tolerance limits of the nominal rating. Capacitance measurement shall be made by means of a polarized capacitance bridge. The polarizing voltage shall be of 2.2 volts. The maximum voltage applied during measurements shall be 1.0 volt rms at 100 Hz and + 25°C. 3. Reverse Voltage: These capacitors are capable of withstanding peak voltage in the reverse direction equal to: 15% of the rated DC voltage at + 25°C, 5% of the rated DC voltage at + 85°C 6. Dissipation factor: The dissipation factor, when measured at 100 Hz, shall not exceed the values below: Table 3 CTS1/CTS13/CTS32 TEMP. SURGE VOLTAGE SURGE VOLTAGE @ + 85°C @ + 125°C CTS13/CTS32 1.30 UR – 749DX/CTS1 1.30 UR 1.30 UC Capacitors shall withstand the surge voltage applied in series with a 1000 ohm resistor, at the rate of one halfminute on, five and a half-minute off, for 1000 successive test cycles at + 85°C or at + 125°C. After test, dissipation factor and leakage current shall meet the initial requirements at + 25°C (see below), capacitance change shall not exceed ± 10% of initial value at + 25°C. 5. Leakage current: Rated voltage UR shall be applied to capacitors during five minutes with a resistor of 1000 ohm in series with each capacitor, before making DC leakage current measurements. The leakage current shall not exceed the following limits: Table 2 + 25°C + 85°C +125°C Document Number 42073 Revision 28-Mar-02 CR > 100 - 55°C 9% 11% 8% 10% + 25°C 6% 8% 6% 8% + 85°C 9% 11% – – + 125°C* 12% 14% 10% 11% *not applicable for CTS13/32 7. Stability at low and high temperature: Capacitance change with temperature shall not exceed the limits of the following table, leakage current and dissipation factor shall be within the limits specified in Tables 2 and 3. TEMPERATURE TEMPERATURE CR ≤ 100 Table 4 4. Surge Voltage: Table 1 PRODUCT TYPE 749DX CRUR ≤ 1900 CRUR > 1900 CTS1/CTS13/CTS32/749DX 0.01 CR x UR or 1µA whichever is greater 0.1 CR x UR or 10µA whichever is greater 0.125 CR x UR or 12.5µA whichever is greater CTS1/CTS13/CTS32/749DX - 55°C - 10% + 85°C + 12% + 125°C * + 15% *not applicable for CTS13/32 8. Impedance: The impedance measured at 100 kHz and 25°C shall not exceed the following values: Table 5 CASE CODE Z (Ω) * A 10 B 5 C 2 D 1 * not applicable for CR ≤ 0.68 µF 9. Life test: After 2000 hours at + 85°C with rated DC voltage applied, or after 2000 hours at + 125°C with category DC voltage applied (for types CTS1, 749DX only) capacitors shall meet the requirements in table 6. Table 6 PRODUCT CAPACITANCE DISSIPATION TYPE CHANGE FACTOR DC LEAKAGE CURRENT CTS1 Within Within CTS13 ±10% of initial of initial CTS32 initial value requirement requirements 749DX @ +25°C @ +25°C @ +25°C For technical questions, contact [email protected] Within 125% www.vishay.com 51 CTS1, CTS13, CTS32, 749DX Hermetically Sealed, Axial-Lead, To CECC Specifications Vishay Sprague PERFORMANCE CHARACTERISTICS (CONT’D) GUIDE TO APPLICATION 10.Humidity test: After 56 days (1350 hours) at + 40°C, 90 to 95% of relative humidity (per IEC 68-2-3) with no voltage applied, capacitors shall meet the requirements in table 7 below. Table 7 1. AC Ripple Current: The maximum allowable ripple current shall be determined from the formula: Irms = P RESR where CAPACITANCE CHANGE Within ± 3% of initial value P = Power Dissipation in Watts at + 25°C as given below DC LEAKAGE CURRENT Within initial requirement @ +25°C - Table 2 RESR = The capacitor Equivalent Series Resistance at the specified frequency. DISSIPATION FACTOR Within initial requirement @ +25°C - Table 3 11.Charge-discharge test (CTS32): Capacitors shall withstand 1,000,000 cycles at + 85°C of 0.5 second charge at DC rated voltage, 0.5 second discharge in an equivalent load resistance of the test fixture lower than 0.5 ohm. Following test, capacitors shall meet the requirements in table 8 below. Table 8 CAPACITANCE CHANGE Within ± 5% of initial value @ + 25°C DC LEAKAGE CURRENT Within initial requirement @ +25°C - Table 2 DISSIPATION FACTOR Within initial requirement @ +25°C - Table 3 Typical values of charge-discharge current (per above test conditions) RATED VOLTAGE UR (V) CHARGE-DISCHARGE CURRENT (A) 2. AC Ripple Current: The maximum allowable ripple voltage shall be determined from the formula: Vrms = P RESR x Z, where Z = The capacitor Impedance at the specified frequency. The calculations are summarized on the graphs page 7 giving the maximum available ripple voltage as a function of frequency. However, the sum of the peak AC voltage plus the DC voltage shall not exceed the rated DC voltage at + 85°C of the capacitor. The sum of the negative peak AC voltage plus the DC voltage shall not allow a voltage reversal exceeding 15% of the rated DC voltage. 3. AC Ripple Current or Voltage Derating Factor: If these capacitors are to be operated at temperatures above + 25°C, the permissible rms ripple current or voltage shall be calculated using the derating factors in the table below: 6.3 13 10 20 16 32 25 50 + 25°C 1.0 40 80 + 55°C 0.8 50 100 + 85°C 0.6 63 126 + 125°C 0.4 12.Insulation test: For capacitors with insulating sleeves, a DC voltage of 100 volts shall be applied for one minute between the case of the capacitor and a metal “V” block in intimate contact with the insulating sleeve. The insulating resistance measured in these conditions shall be at least 100 megohms. 13.Lead pull test: Leads shall withstand the following test (IEC 68 - 2 - 2): TEMPERATURE DERATING FACTOR 4. Power Dissipation: Power dissipation will be affected by the heat sinking capability of the mounting surface. Non-sinusoidial ripple current may produce heating effects which differ from those shown in the following table. It is important that the equivalent Irms value be established when calculating permissible operating levels. CASE CODE POWER DISSIPATION @ + 25°C (WATTS) • Tensile stress of 5N (cases A and B) or 10N (cases C and D) for 10 seconds in any direction A 0.115 B 0.145 • One bend in each direction C 0.185 • Two consecutive rotations of 180° D 0.225 www.vishay.com 52 For technical questions, contact [email protected] Document Number 42073 Revision 28-Mar-02 CTS1, CTS13, CTS32, 749DX Hermetically Sealed, Axial-Lead, To CECC Specifications Vishay Sprague TAPE AND REEL PACKAGING S MEETS IEC 286-1 1.5 max. L1 - L2 = 1.5mm max S = component spacing (cumulative tolerance on 20 units = 4mm) b = tape spacing c = overall length 0.2 ± 0.3 L1 L2 b c DIMENSIONS in millimeters REEL PACK AMMO PACK CASE SIZE REEL AND AMMO S OPTION P OPTION R b c MAX b c MAX A 5.0 ± 0.3 63 ± 2 78 53 ± 2 B 5.0 ± 0.3 63 ± 2 78 C 10.0 ± 0.3 63 ± 2 D 10.0 ± 0.3 63 ± 2 PACKAGING CODE P OPTION G QTY PER REEL b c MAX 68 2500 53 ± 2 68 1500 53 ± 2 68 2500 53 ± 2 68 1000 78 63 ± 2 78 1000 53 ± 2 68 250 78 63 ± 2 78 500 53 ± 2 68 250 R QTY PER BOX G MARKING Capacitors shall be marked with SPRAGUE and/or the registered trademark 2 at vendor‘s option ; the type number ; rated capacitance and tolerance (with a letter code, if different from ± 20%, K = ± 10% ; J = ± 5%) ; rated DC voltage at + 85°C and the date code of manufacture. Capacitors shall be marked on one end with a “plus” sign (+) to identify the positive terminal. Document Number 42073 Revision 28-Mar-02 For technical questions, contact [email protected] www.vishay.com 53