MCC DLFR106 THRU DLFR107 omponents 21201 Itasca Street Chatsworth !"# $ % !"# Features l Fast Switching Speed l Low Leakage Current l Metalurgically Bonded Construction l Surface Mount Applications 1 Amp Glass Passivated, Fast Recovery Rectifier 800 to 1000 Volts Maximum Ratings o o l Operating & Storage Temperature: -65 C to +150 C l Maximum Thermal Resistance; 30 C/W Junction To Lead MELF o Cathode Mark Maximum Maximum Reccurrent RMS Peak Reverse Voltage Voltage Maximum DC Blocking Voltage MCC Catalog Number Device Marking DLFR106 ----- 800V 560V 800V DLFR107 ----- 1000V 700V 1000V C B A Electrical Characteristics @ 25oC Unless Otherwise Specified Average Forward Current Peak Forward Surge Current Maximum Instantaneous Forward Voltage Maximum DC Reverse Current At Rated DC Blocking Voltage Maximum Reverse Recovery Times DLFR106 DLFR107 Typical Junction Capacitance I F(AV) 1.0A T J=55 o C IFSM 30A 8.3ms half sine VF 1.3V I FM=1.0A T A=25 oC IR 5.0uA T J=25 o C 100uA T =125 oC J t rr I F=0.5A, 250ns I R=1.0A, 500ns I rr=0.25A Cj 15pF DIMENSIONS DIM A B C INCHES MIN .190 --.095 MM MIN 4.80 --2.40 MAX .205 .022 .105 MAX 5.20 .55 2.67 SUGGESTED SOLDER PAD LAYOUT .220” .115” Measured at 1.0MHz, V R=4.0V Pulse test: Pulse width 300 usec, duty cycle 1%. www.mccsemi.com .035” NOTE Nominal ∅ MCC DLFR106 thru DLFR107 Figure 1 Typical Forward Characteristics 20 Figure 2 Forward Derating Curve 10 1.2 6 4 1.0 2 Amps .8 1 .6 .6 Amps .4 .4 .2 25°C .1 .2 Single Phase, Half Wave 60Hz Resistive or Inductive Load .06 0 .04 0 50 75 100 125 150 175 °C .02 Average Forward Rectified Current - Amperes/ersus .01 .4 .6 .8 1.0 1.2 Ambient Temperature -oC 1.4 Volts Instantaneous Forward Current - Amperesversus Instantaneous Forward Voltage - Volts Figure 3 Junction Capacitance 100 60 40 20 pF TJ=25°C 10 6 4 2 1 .1 .2 .4 1 Volts 2 4 10 20 40 100 200 Junction Capacitance - pFversus Reverse Voltage - Volts www.mccsemi.com 400 1000 MCC DLFR106 thru DLFR107 Figure 4 Typical Reverse Characteristics Figure 5 Peak Forward Surge Current 100 60 60 40 50 20 40 10 30 6 Amps 4 T =100°C A 20 10 5 0 2 µAmps 1 1 2 4 .6 6 8 10 20 40 60 80 100 Cycles .4 Peak Forward Surge Current - Amperesversus Number Of Cycles At 60Hz - Cycles .2 .1 TA=25°C .06 .04 .02 .01 20 40 60 80 100 120 140 Volts Instantaneous Reverse Leakage Current - MicroAmperesversus Percent Of Rated Peak Reverse Voltage - Volts Figure 6 Reverse Recovery Time Characteristic And Test Circuit Diagram 50Ω 10Ω trr +0.5A 0 Pulse Generator Note 2 25Vdc 1Ω Notes: 1. Rise Time = 7ns max. Input impedance = 1 megohm, 22pF 2. Rise Time = 10ns max. Source impedance = 50 ohms 3. Resistors are non-inductive Oscilloscope Note 1 -0.25 -1.0 1cm Set Time Base for 20/100ns/cm www.mccsemi.com