5V/3.3V PROGRAMMABLE FREQUENCY SYNTHESIZER (50MHz to 950MHz) FEATURES ClockWorks™ SY89430V DESCRIPTION ■ ■ ■ ■ ■ ■ ■ ■ 5V and 3.3V power supply options 50MHz to 950MHz differential PECL outputs ±25ps peak-to-peak output jitter Minimal frequency over-shoot Synthesized architecture Serial 3 wire interface Parallel interface for power-on Internal quartz reference oscillator driven by quartz crystal ■ External loop filter optimizes performance/cost ■ Applications note (AN-07) for ease of design-ins ■ Available in 28-pin PLCC and SOIC packages The SY89430V is a general purpose, synthesized clock source targeting applications that require both serial and parallel interfaces. Its internal VCO will operate over a range of frequencies from 400MHz to 950MHz. The differential PECL output can be configured to be the VCO frequency divided by 1, 2, 4 or 8. With the output configured to divide the VCO frequency by 2, and with a 16MHz external quartz crystal used to provide the reference frequency, the output frequency can be specified in 1MHz steps. TEST GND (TTL) VCC (TTL) FOUT GND VCC_OUT FOUT PIN CONFIGURATION M[0] 1 28 P_LOAD M[1] 2 27 VCC1 M[2] 3 26 XTAL2 M[3] 4 25 XTAL1 M[4] 5 24 LOOP_REF M[5] 6 23 LOOP_FILTER 22 VCC_QUIET 21 S_LOAD 25 24 23 22 21 20 19 S_CLOCK 26 18 N[1] S_DATA 27 17 N[0] S_LOAD 28 16 M[8] VCC_QUIET PLCC TOP VIEW 15 M[7] LOOP _FILTER 2 14 M[6] LOOP_REF 3 13 M[5] XTAL1 4 12 M[4] 9 APPLICATIONS ■ ■ ■ ■ ■ ■ ■ ■ TOP VIEW SOIC Z28-1 M[6] 7 M[7] 8 M[8] 9 20 S_DATA N[0] 10 19 S_CLOCK N[1] 11 18 VCC_OUT GND (TTL) 12 17 FOUT TEST 13 16 FOUT VCC (TTL) 14 15 GND 10 11 M[3] 8 M[2] 7 M[1] 6 VCC1 XTAL2 5 P_LOAD M[0] 1 Workstations Advanced communications High end consumer High-performance computing RISC CPU clock Graphics pixel clock Test equipment Other high-performance processor-based applications Rev.: E 1 Amendment: /0 Issue Date: May 2000 ClockWorks™ SY89430V Micrel BLOCK DIAGRAM +3.3V or +5.0V PLL FREF ÷8 PHASE DETECTOR VCO PECL 10-25MHz Fundamental Crystal OSC ÷M 3 WIRE INTERFACE ÷N 400 – 950 MHz FOUT INTERFACE LOGIC SERIAL TEST PARALLEL CONFIG INFO DETAILED BLOCK DIAGRAM 150 +3.3V or +5.0V 0.47µF 3300pF 2 3 6, 21 1 LOOP_REF LOOP_FILTER +3.3V or +5.0V VCC_QUIET VCC1 FREF ÷8 PHASE DETECTOR VCO 1 4 0 +3.3V or +5.0V 400 - 950 MHz VCC_OUT T110 25 XTAL1 10–25MHz Fundamental Crystal OSC 5 24 ÷N (2,4,8,1) 9-BIT ÷ M COUNTER 23 FOUT FOUT XTAL2 L = LATCH H = Transparent FOUT ÷ 4 — 7 LATCH 28 LATCH S_CLOCK ÷ M — 6 S_LOAD LATCH P_LOAD 7 LOW — 5 FOUT — 4 0 0 1 1 ÷M— 3 FREF — 2 S_DATA 27 9-BIT SR 2-BIT SR 3-BIT SR HIGH — 1 0 S_CLOCK 26 19,22 17,18 8 -> 16 9 2 N[1:0] M[8:0] NOTE: Pin numbers reference PLCC pinout. 2 20 TEST ClockWorks™ SY89430V Micrel PIN DESCRIPTIONS INPUTS OUTPUTS XTAL1, XTAL2 These pins form an oscillator when connected to an external crystal. The crystal is series resonant. FOUT, FOUT These differential positive-referenced ECL signals (PECL) are the output of the synthesizer. S_LOAD This TTL pin loads the configuration latches with the contents of the shift registers. The latches will be transparent when this signal is HIGH; thus, the register data must be stable on the HIGH-to-LOW transition of S_LOAD for proper operation. TEST The function of this TTL output is determined by the serial configuration bits T[2:0]. S_DATA This TTL pin is the input to the serial configuration shift registers. VCC1 This is the positive supply for the chip and is normally connected to +3.3V or +5.0V. S_CLOCK This TTL pin clocks the serial configuration shift registers. On the rising edge of this signal, data from S_DATA is sampled. VCC_OUT This is the positive reference for the PECL outputs, FOUT and FOUT. It is constrained to be less than or equal to VCC1. P_LOAD This TTL pin loads the configuration latches with the contents of the parallel inputs. The latches will be transparent when this signal is LOW; thus, the parallel data must be stable on the LOW-to-HIGH transition of P_LOAD for proper operation. VCC_QUIET This is the positive supply for the PLL and should be as noisefree as possible for low-jitter operation. POWER GND These pins are the negative supply for the chip and are normally all connected to ground. M[8:0] These TTL pins are used to configure the PLL loop divider. They are sampled on the LOW-to-HIGH transition of P_LOAD. M[8] is the MSB, M[0] is the LSB. The binary count on the M pins equates to the divide-by value for the PLL. OTHER LOOP_FILTER This is an analog I/O pin that provides the loop filter for the PLL. N[1:0] These TTL pins are used to configure the output divider modulus. They are sampled on the LOW-to-HIGH transition of P_LOAD. N[1:0] Output Division 00 2 01 4 10 8 11 1 LOOP_REF This is an analog I/O pin that provides a reference voltage for the PLL. ABSOLUTE MAXIMUM RATINGS(1) Symbol Parameter Value Unit VCC Power Supply Voltage –0.5 to +7.0 V VI Input Voltage –0.5 to +7.0 V IOUT Output Source 50 100 mA Tstore Storage Temperature –65 to +150 °C TA Operating Temperature –0 to +75 °C Continuous Surge NOTE: 1. Permanent device damage may occur if ABSOLUTE MAXIMUM RATINGS are exceeded. This is a stress rating only and functional operation is not implied at conditions other than those detailed in the operational sections of this data sheet. Exposure to ABSOLUTE MAXIMUM RATlNG conditions for extended periods may affect device reliability. 3 ClockWorks™ SY89430V Micrel WITH 16MHZ INPUT VCO Frequency (MHz) 400 402 404 406 • • • 944 946 948 950 M Count 200 201 202 203 • • • 472 473 474 475 256 M8 0 0 0 0 • • • 1 1 1 1 128 M7 1 1 1 1 • • • 1 1 1 1 64 M6 1 1 1 1 • • • 1 1 1 1 32 M5 0 0 0 0 • • • 0 0 0 0 16 M4 0 0 0 0 • • • 1 1 1 1 8 M3 1 1 1 1 • • • 1 1 1 1 4 M2 0 0 0 0 • • • 0 0 0 0 2 M1 0 0 1 1 • • • 0 0 1 1 1 M0 0 1 0 1 • • • 0 1 0 1 FUNCTIONAL DESCRIPTION The configuration logic has two sections: serial and parallel. The parallel interface uses the values at the M[8:0] and N[1:0] inputs to configure the internal counters. Normally upon system reset, the P_LOAD input is held LOW until sometime after power becomes valid. With S_LOAD held LOW, on the LOW-to-HIGH transition of P_LOAD, the parallel inputs are captured. The parallel interface has priority over the serial interface. Internal pull-up resistors are provided on the M[8:0] and N[1:0] inputs to reduce component count. The serial interface logic is implemented with a 14-bit shift register scheme. The register shifts once per rising edge of the S_CLOCK input. The serial input S_DATA must meet set-up and hold timing as specified in the AC parameters section of this data sheet. With P_LOAD held HIGH, the configuration latches will capture the value in the shift register on the HIGH-to-LOW edge of the S_LOAD input. See the programming section for more information. The TEST output reflects various internal node values and is controlled by the T[2:0] bits in the serial data stream. See the programming section for more information. The internal oscillator uses the external quartz crystal as the basis of its frequency reference. The output of the reference oscillator is divided by eight before being sent to the phase detector. With a 16MHz crystal, this provides a reference frequency of 2MHz. The VCO within the PLL operates over a range of 400– 950MHz. Its output is scaled by a divider that is configured by either the serial or parallel interfaces. The output of this loop divider is also applied to the phase detector. The phase detector and loop filter force the VCO output frequency to be M times the reference frequency by adjusting the VCO control voltage. Note that for some values of M (either too high or too low) the PLL will not achieve loop lock. External loop filter components are utilized to allow for optimal phase jitter performance. The output of the VCO is also passed through an output divider before being sent to the PECL output driver. The output divider is configured through either the serial or the parallel interfaces and can provide one of four divider ratios (1, 2, 4 or 8). This divider extends the performance of the part while providing a 50% duty cycle. The output driver is driven differentially from the output divider and is capable of driving a pair of transmission lines terminated in 50Ω to VCC –2volts. The positive reference for the output driver is provided by a dedicated power pin (VCC_OUT) to reduce noise induced jitter. 4 ClockWorks™ SY89430V Micrel PROGRAMMING INTERFACE Programming the device is accomplished by properly configuring the internal dividers to produce the desired frequency at the outputs. The output frequency can be represented by this formula: FOUT = ( The TEST output provides visibility for one of several internal nodes (as determined by the T[1:0] bits in the serial configuration stream). It is not configurable through the parallel interface. Although it is possible to select the node that represents FOUT, the TTL output may not be able to toggle fast enough for some of the higher output frequencies. The T2, T1, T0 configuration latches are preset to 000 when P_LOAD is low, so that the FOUT outputs are as jitter-free as possible. The serial configuration port can be used to select one of the alternate functions for this pin. The Test register is loaded with the first three bits, the N register with the next two and the M register with the final eight bits of the data stream on the S_DATA input. For each register the most significant bit is loaded first (T2, N1 and M8). When T[2:0] is set to 100 the SY89430V is placed in PLL bypass mode. In this mode the S_CLOCK input is fed directly into the M and N dividers. The N divider drives the FOUT differential pair and the M counter drives the TEST output pin. In this mode the S_CLOCK input could be used for low speed board level functional test or debug. Bypassing the PLL and driving FOUT directly gives the user more control on the test clocks sent through the clock tree (See detailed Block Diagram). Because the S_CLOCK is a TTL level the input frequency is limited to 250MHz or less. This means the fastest the FOUT pin can be toggled via the S_CLOCK is 125MHz as the minimum divide ratio of the N counter is 2. Note that the M counter output on the TEST output will not be a 50% duty cycle due to the way the divider is implemented. M FXTAL )x 8 N Where FXTAL is the crystal frequency, M is the loop divider modulus, and N is the output divider modulus. Note that it is possible to select values of M such that the PLL is unable to achieve loop lock. To avoid this, always make sure that M is selected to be 200 ≤ M ≤ 510 for a 16MHz input reference. M[8:0] and N[1:0] are normally specified once at power-on, through the parallel interface, and then possibly again through the serial interface. This approach allows the designer to bring up the application at one frequency and then change or finetune the clock, as the ability to control the serial interface becomes available. To minimize transients in the frequency domain, the output should be varied in the smallest step size possible. T2 T1 T0 TEST 0 0 0 Data Out – Last Bit SR FVCO ÷ N 0 0 1 HIGH FVCO ÷ N 0 1 0 FREF FVCO ÷ N 0 1 1 M Counter Output FVCO ÷ N 1 0 0 FOUT FVCO ÷ N 1 0 1 LOW FVCO ÷ N 1 1 0 S_CLOCK ÷ M S_CLOCK ÷ N 1 1 1 FOUT ÷ 4 FVCO ÷ N FOUT / FOUT S_CLOCK S_DATA T2 T1 T0 N1 N0 M8 M6 M5 M4 M3 M2 M1 M0 Last Bit First Bit S_LOAD M[8:0] N[1:0] M7 M,N P_LOAD 5 ClockWorks™ SY89430V Micrel 100H ECL DC ELECTRICAL CHARACTERISTICS VCC1 = VCC_QUIET = VCC_TTL = VCC_OUT = +3.3V to +5.0V ±5%; TA = 0°C to +75°C Symbol Parameter Min. Max. Unit Condition VOH Output HIGH Voltage VCC_OUT –1.075 VCC_OUT –0.830 V 50Ω to VCC_OUT –2V VOL Output LOW Voltage VCC_OUT –1.860 VCC_OUT –1.570 V 50Ω to VCC_OUT –2V TTL DC ELECTRICAL CHARACTERISTICS VCC1 = VCC_QUIET = VCC_TTL = VCC_OUT = +3.3V to +5.0V ±5%; TA = 0°C to +75°C TA = 0°C Symbol Parameter TA = +25°C TA = +75°C Min. Max. Min. Max. Min. Max. Unit Condition VIH Input HIGH Voltage 2.0 — 2.0 — 2.0 — V — VIL Input LOW Voltage — 0.8 — 0.8 — 0.8 V — IIH Input HIGH Current — 50 — 50 — 50 µA VIN = 2.7V IIL Input LOW Current — –0.6 — –0.6 — –0.6 mA VIN = 0.5V VIK Input Clamp Voltage — –1.2 — –1.2 — –1.2 V IIN = –12mA VOH Output HIGH Voltage — 2.0 — 2.0 — 2.0 V IOH = –2.0mA VOL Output LOW Voltage — 0.5 — 0.5 — 0.5 V IOL = 8mA IOS Output Short Circuit Current –100 (Typ.) mA VOUT = 0V ICC1 Supply Current — Typical % of ICC1 VCC1 VCC_OUT VCC_QUIET VCC_TTL –100 (Typ.) 220 — –100 (Typ.) 220 — 220 0.91X of 5V Val. 0.91X of 5V Val. 0.91X of 5V Val. 33% 9% 14% 44% 33% 9% 14% 44% 33% 9% 14% 44% mA 5.0V ±5% mA 3.3V ±5% AC ELECTRICAL CHARACTERISTICS VCC1 = VCC_QUIET = VCC_TTL = VCC_OUT = +3.3V to +5.0V ±5%; TA = 0°C to +75°C TA = 0°C Symbol Parameter (1) TA = +25°C TA = +75°C Min. Max. Min. Max. Min. Max. Unit Condition Fundamental Cyrstal fMAXI Maximum Input Frequency S_CLOCK Xtal Oscillator — 10 10 25 — 10 10 25 — 10 10 25 MHz fMAXO Maximum Output Frequency VCO (Internal) FOUT 400 50 950 950 400 50 950 950 400 50 950 950 MHz tLOCK Maximum PLL Lock Time — 10 — 10 — 10 ms tjitter Cycle-to-Cycle Jitter (Peak-toPeak) — ±25 — ±25 — ±25 ps tS Setup Time S_DATA to S_CLOCK S_CLOCK to S_LOAD M, N to P_LOAD 20 20 20 — — — 20 20 20 — — — 20 20 20 — — — ns tH Hold Time S_DATA to S_CLOCK S_CLOCK to S_LOAD M, N to P_LOAD 20 20 20 — — — 20 20 20 — — — 20 20 20 — — — ns tpw(MIN) Minimum Pulse Width S_LOAD P_LOAD 50 50 — — 50 50 — — 50 50 — — ns tDC FOUT Duty Cycle 45 55 45 55 45 55 % tr tf Output Rise/Fall 20% to 80% FOUT 100 500 100 500 100 500 ps Test output static NOTE: 1. 10MHz is the maximum frequency to load the feedback divide registers. S_CLOCK can be switched at high frequencies when used as a test clock in TEST_MODE 6. 6 ClockWorks™ SY89430V Micrel TIMING DIAGRAM S_DATA S_CLOCK tHOLD tSET-UP S_LOAD tSET-UP M[8:0] N[1:0] P_LOAD tHOLD tSET-UP PRODUCT ORDERING CODE Ordering Code Package Type Operating Range SY89430VJC J28-1 Commercial SY89430VJCTR J28-1 Commercial SY89430VZC Z28-1 Commercial SY89430VZCTR Z28-1 Commercial 7 ClockWorks™ SY89430V Micrel 28 LEAD SOIC .300" WIDE (Z28-1) Rev. 02 8 ClockWorks™ SY89430V Micrel 28 LEAD PLCC (J28-1) Rev. 03 MICREL-SYNERGY TEL 3250 SCOTT BOULEVARD SANTA CLARA CA 95054 USA + 1 (408) 980-9191 FAX + 1 (408) 914-7878 WEB http://www.micrel.com This information is believed to be accurate and reliable, however no responsibility is assumed by Micrel for its use nor for any infringement of patents or other rights of third parties resulting from its use. No license is granted by implication or otherwise under any patent or patent right of Micrel Inc. © 2000 Micrel Incorporated 9