MITSUBISHI RF MOSFET MODULE ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS RA07M2127M 215-270MHz 7W 7.2V, 2Stage Amp. For PORTABLE RADIO DESCRIPTION The RA07M2127M is a 7-watt RF MOSFET Amplifier Module for 7.2-volt portable radios that operate in the 215- to 270-MHz range. The battery can be connected directly to the drain of the enhancement-mode MOSFET transistors. Without the gate voltage (V GG=0V), only a small leakage current flows into the drain and the RF input signal attenuates up to 60 dB. The output power and drain current increase as the gate voltage increases. With a gate voltage around 2.5V (minimum), output power and drain current increases substantially. The nominal output power becomes available at 3V (typical) and 3.5V (maximum). At VGG=3.5V, the typical gate current is 1 mA. This module is designed for non-linear FM modulation, but may also be used for linear modulation by setting the drain quiescent current with the gate voltage and controlling the output power with the input power. FEATURES • Enhancement-Mode MOSFET Transistors (IDD≅0 @ VDD=7.2V, VGG=0V) BLOCK DIAGRAM 2 3 1 4 5 1 RF Input (Pin) 2 Gate Voltage (VGG), Power Control 3 Drain Voltage (VDD), Battery 4 RF Output (Pout) 5 RF Ground (Case) PACKAGE CODE: H46S • Pout>7W @ VDD=7.2V, VGG=3.5V, Pin=20mW • ηT>45% @ Pout=6.5W (V GG control), VDD=7.2V, Pin=20mW • Broadband Frequency Range: 215-270MHz • Low-Power Control Current IGG=1mA (typ) at VGG=3.5V • Module Size: 30 x 10 x 5.4 mm • Linear operation is possible by setting the quiescent drain current with the gate voltage and controlling the output power with the input power ORDERING INFORMATION: ORDER NUMBER RA07M2127M-E01 RA07M2127M-01 SUPPLY FORM Antistatic tray, 25 modules/tray (Japan - packed without desiccator) RA07M2127M MITSUBISHI ELECTRIC 1/9 25 April 2003 ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS MITSUBISHI RF POWER MODULE RA07M2127M MAXIMUM RATINGS (Tcase=+25°C, unless otherwise specified) SYMBOL PARAMETER CONDITIONS VDD Drain Voltage VGG<3.5V VGG Gate Voltage Pin Input Power Pout Output Power Tcase(OP) Tstg RATING UNIT 9.2 V VDD<7.2V, Pin=0mW 4 V f=215-270MHz, ZG=ZL=50Ω 30 mW 10 W Operation Case Temperature Range -30 to +90 °C Storage Temperature Range -40 to +110 °C The above parameters are independently guaranteed. ELECTRICAL CHARACTERISTICS (Tcase=+25°C, ZG=ZL=50Ω, unless otherwise specified) SYMBOL PARAMETER f CONDITIONS Frequency Range Pout Output Power ηT Total Efficiency nd MIN TYP 215 VDD=7.2V,VGG=3.5V, Pin=20mW 2 Harmonic ρ in Input VSWR IGG Gate Current — Stability VDD=4.0-9.2V, Pin=10-30mW, Pout<8W (VGG control), Load VSWR=4:1 — Load VSWR Tolerance VDD=9.2V, Pin=20mW, Pout=7W (VGG control), Load VSWR=20:1 UNIT 270 MHz 7 W 45 % Pout=6.5W (VGG control), VDD=7.2V, Pin=20mW 2fo MAX -25 dBc 4:1 — 1 mA No parasitic oscillation — No degradation or destroy — All parameters, conditions, ratings, and limits are subject to change without notice. RA07M2127M MITSUBISHI ELECTRIC 2/9 25 April 2003 MITSUBISHI RF POWER MODULE ELECTROSTATIC SENSITIVE DEVICE RA07M2127M OBSERVE HANDLING PRECAUTIONS TYPICAL PERFORMANCE (Tcase=+25°C, ZG=ZL=50Ω, unless otherwise specified) rd OUTPUT POWER, TOTAL EFFICIENCY, and INPUT VSWR versus FREQUENCY 2nd, 3 HARMONICS versus FREQUENCY 8 80 η T @Pout=6.5W 6 60 VDD =7.2V Pin=20mW 4 40 ρ in @Pout=6.5W 2 0 210 220 TOTAL EFFICIENCY ρin (-) 100 20 230 240 250 260 FREQUENCY f(MHz) -40 2nd @P out=6.5W -50 -60 0 280 270 VDD =7.2V Pin=20mW -30 HARMONICS (dBc) Pout @VGG=3.5V -20 ηT (%) 120 10 INPUT VSWR OUTPUT POWER P out (W) 12 rd 3 @P out=6.5W -70 210 OUTPUT POWER, POWER GAIN and DRAIN CURRENT versus INPUT POWER 220 230 240 250 260 FREQUENCY f(MHz) 270 280 OUTPUT POWER, POWER GAIN and DRAIN CURRENT versus INPUT POWER 50 5 50 5 3 20 2 IDD f=215MHz, VDD =7.2V, VGG=3.5V 10 1 0 0 -15 -10 -5 0 5 10 15 Pout 40 4 30 3 I DD 20 2 f=250MHz, VDD=7.2V, VGG=3.5V 10 1 0 20 IDD(A) 30 Gp DRAIN CURRENT 4 OUTPUT POWER P out (dBm) POWER GAIN Gp(dB) 40 DRAIN CURRENT I DD (A) Pout POWER GAIN Gp(dB) OUTPUT POWER P out (dBm) Gp 0 -15 -10 INPUT POWER Pin (dBm) -5 0 5 10 INPUT POWER Pin (dBm) 15 20 OUTPUT POWER, POWER GAIN and DRAIN CURRENT versus INPUT POWER 5 Gp Pout 40 4 30 3 20 2 IDD f=270MHz, VDD=7.2V, VGG=3.5V 10 DRAIN CURRENT I DD (A) 1 0 0 -10 -5 0 5 10 INPUT POWER Pin (dBm) 15 20 OUTPUT POWER and DRAIN CURRENT versus DRAIN VOLTAGE OUTPUT POWER and DRAIN CURRENT versus DRAIN VOLTAGE 5 8 4 6 3 4 ID D 2 2 1 0 0 2 RA07M2127M 3 4 5 6 7 8 DRAIN VOLTAGE VD D(V) 9 10 out (W) 14 6 Pout 10 16 7 OUTPUT POWER P 12 8 DD (A) f=215MHz, VGG=3.5V, Pi n=20mW 14 DRAIN CURRENT I OUTPUT POWER P out (W) 16 8 f=250MHz, VGG=3.5V, Pi n=20mW 12 7 6 Pout 10 5 8 4 6 3 ID D 4 2 2 1 0 DD (A) -15 DRAIN CURRENT I OUTPUT POWER P out (dBm) POWER GAIN Gp(dB) 50 0 2 3 4 5 6 7 8 DRAIN VOLTAGE VD D (V) MITSUBISHI ELECTRIC 3/9 9 10 25 April 2003 MITSUBISHI RF POWER MODULE ELECTROSTATIC SENSITIVE DEVICE RA07M2127M OBSERVE HANDLING PRECAUTIONS TYPICAL PERFORMANCE (Tcase=+25°C, ZG=ZL=50Ω, unless otherwise specified) OUTPUT POWER and DRAIN CURRENT versus DRAIN VOLTAGE 8 14 12 7 Pout 6 10 5 8 4 6 3 ID D 4 2 2 1 0 DD (A) f=270MHz, VGG=3.5V, Pi n=20mW DRAIN CURRENT I 0 3 4 5 6 7 8 DRAIN VOLTAGE VD D (V) 9 10 OUTPUT POWER and DRAIN CURRENT versus GATE VOLTAGE OUTPUT POWER and DRAIN CURRENT versus GATE VOLTAGE 8 4 6 3 ID D 4 2 2 1 0 0 1 1.5 2 2.5 3 GATE VOLTAGE VGG(V) 3.5 OUTPUT POWER P 5 Pout DD (A) 10 12 out (W) 6 f=215MHz, VDD=7.2V, Pi n=20mW DRAIN CURRENT I OUTPUT POWER P out (W) 12 6 f=250MHz, VDD =7.2V, Pin=20mW 10 5 Pout 8 4 6 3 4 2 I DD 2 1 0 4 DD (A) 2 DRAIN CURRENT I OUTPUT POWER P out (W) 16 0 1 1.5 2 2.5 3 GATE VOLTAGE VGG (V) 3.5 4 OUTPUT POWER and DRAIN CURRENT versus GATE VOLTAGE 6 10 5 Pout 8 4 6 3 ID D 4 2 2 1 0 DD (A) f=270MHz, VDD=7.2V, Pi n=20mW DRAIN CURRENT I OUTPUT POWER P out (W) 12 0 1 RA07M2127M 1.5 2 2.5 3 GATE VOLTAGE VGG(V) 3.5 4 MITSUBISHI ELECTRIC 4/9 25 April 2003 MITSUBISHI RF POWER MODULE ELECTROSTATIC SENSITIVE DEVICE RA07M2127M OBSERVE HANDLING PRECAUTIONS OUTLINE DRAWING (mm) 30.0 ±0.2 26.6 ±0.2 21.2 ±0.2 2 3 7.4 ±0.2 4 3.0 ±0.2 6.0 ±1 1 6.0 ±0.2 5 6.0 ±0.2 2-R1.5 ±0.1 3.0 ±0.2 (4.4) 10.0 ±0.2 (1.7) Ø0.45 ±0.15 6.1 ±1 13.7 ±1 18.8 ±1 (5.4) 1.5 ±0.2 2.3 ±0.4 3.5 ±0.2 23.9 ±1 1 RF Input (P in) 2 Gate Voltage (V GG) 3 Drain Voltage (V DD) 4 RF Output (P out) 5 RF Ground (Case) RA07M2127M MITSUBISHI ELECTRIC 5/9 25 April 2003 MITSUBISHI RF POWER MODULE ELECTROSTATIC SENSITIVE DEVICE RA07M2127M OBSERVE HANDLING PRECAUTIONS TEST BLOCK DIAGRAM Power Meter DUT 1 Signal Generator Attenuator Preamplifier Attenuator Directional Coupler 2 3 ZG=50Ω C1 Spectrum Analyzer 4 ZL=50Ω Directional Coupler Attenuator Power Meter C2 + DC Power Supply V GG C1, C2: 4700pF, 22uF in parallel 5 + DC Power Supply V DD 1 RF Input (P in) 2 Gate Voltage (V GG) 3 Drain Voltage (V DD) 4 RF Output (P out) 5 RF Ground (Case) EQUIVALENT CIRCUIT 2 3 1 4 5 RA07M2127M MITSUBISHI ELECTRIC 6/9 25 April 2003 MITSUBISHI RF POWER MODULE ELECTROSTATIC SENSITIVE DEVICE RA07M2127M OBSERVE HANDLING PRECAUTIONS PRECAUTIONS, RECOMMENDATIONS, and APPLICATION INFORMATION: Construction: This module consists of an alumina substrate soldered onto a copper flange. For mechanical protection, a plastic cap is attached with silicone. The MOSFET transistor chips are die bonded onto metal, wire bonded to the substrate, and coated with resin. Lines on the substrate (eventually inductors), chip capacitors, and resistors form the bias and matching circuits. Wire leads soldered onto the alumina substrate provide the DC and RF connection. Following conditions must be avoided: a) Bending forces on the alumina substrate (for example, by driving screws or from fast thermal changes) b) Mechanical stress on the wire leads (for example, by first soldering then driving screws or by thermal expansion) c) Defluxing solvents reacting with the resin coating on the MOSFET chips (for example, Trichlorethylene) d) Frequent on/off switching that causes thermal expansion of the resin e) ESD, surge, overvoltage in combination with load VSWR, and oscillation ESD: This MOSFET module is sensitive to ESD voltages down to 1000V. Appropriate ESD precautions are required. Mounting: Heat sink flatness must be less than 50 µm (a heat sink that is not flat or particles between module and heat sink may cause the ceramic substrate in the module to crack by bending forces, either immediately when driving screws or later when thermal expansion forces are added). A thermal compound between module and heat sink is recommended for low thermal contact resistance and to reduce the bending stress on the ceramic substrate caused by the temperature difference to the heat sink. The module must first be screwed to the heat sink, then the leads can be soldered to the printed circuit board. M3 screws are recommended with a tightening torque of 0.4 to 0.6 Nm. Soldering and Defluxing: This module is designed for manual soldering. The leads must be soldered after the module is screwed onto the heat sink. The soldering temperature must be lower than 260°C for a maximum of 10 seconds, or lower than 350°C for a maximum of three seconds. Ethyl Alcohol is recommend for removing flux. Trichlorethylene solvents must not be used (they may cause bubbles in the coating of the transistor chips which can lift off the bond wires). Thermal Design of the Heat Sink: At Pout=7W, V DD=7.2V and Pin=20mW each stage transistor operating conditions are: 1st Pin (W) 0.02 Pout (W) 2 Rth(ch-case) (°C/W) 4.5 IDD @ ηT =45% (A) 0.48 2nd 2 7 2.4 1.68 Stage VDD (V) 7.2 The channel temperatures of each stage transistor Tch = Tcase + (V DD x IDD - Pout + Pin) x Rth(ch-case) are: Tch1 = Tcase + (7.2V x 0.48A – 2W + 0.02W) x 4.5°C/W = Tcase + 6.6 °C Tch2 = Tcase + (7.2V x 1.68A – 7W + 2W) x 2.4°C/W = Tcase + 17.0 °C For long-term reliability, it is best to keep the module case temperature (Tcase) below 90°C. For an ambient temperature Tair=60°C and Pout=7W, the required thermal resistance Rth (case-air) = ( Tcase - Tair) / ( (P out / ηT ) - Pout + Pin ) of the heat sink, including the contact resistance, is: Rth(case-air) = (90°C - 60°C) / (7W/45% – 7W + 0.02W) = 3.5 °C/W When mounting the module with the thermal resistance of 3.5 °C/W, the channel temperature of each stage transistor is: Tch1 = Tair + 36.6 °C Tch2 = Tair + 47.0 °C The 175°C maximum rating for the channel temperature ensures application under derated conditions. RA07M2127M MITSUBISHI ELECTRIC 7/9 25 April 2003 ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS MITSUBISHI RF POWER MODULE RA07M2127M Output Power Control: Depending on linearity, the following two methods are recommended to control the output power: a) Non-linear FM modulation: By the gate voltage (V GG). When the gate voltage is close to zero, the RF input signal is attenuated up to 60 dB and only a small leakage current flows from the battery into the drain. Around VGG=2.5V, the output power and drain current increases substantially. Around VGG=3V (typical) to VGG=3.5V (maximum), the nominal output power becomes available. b) Linear AM modulation: By RF input power Pin. The gate voltage is used to set the drain’s quiescent current for the required linearity. Oscillation: To test RF characteristics, this module is put on a fixture with two bias decoupling capacitors each on gate and drain, a 4.700 pF chip capacitor, located close to the module, and a 22 µF (or more) electrolytic capacitor. When an amplifier circuit around this module shows oscillation, the following may be checked: a) Do the bias decoupling capacitors have a low inductance pass to the case of the module? b) Is the load impedance ZL=50Ω? c) Is the source impedance ZG=50Ω? Frequent on/off switching: In base stations, frequent on/off switching can cause thermal expansion of the resin that coats the transistor chips and can result in reduced or no output power. The bond wires in the resin will break after long-term thermally induced mechanical stress. Quality: Mitsubishi Electric is not liable for failures resulting from base station operation time or operating conditions exceeding those of mobile radios. This module technology results from more than 20 years of experience, field proven in tens of millions of mobile radios. Currently, most returned modules show failures such as ESD, substrate crack, and transistor burnout, which are caused by improper handling or exceeding recommended operating conditions. Few degradation failures are found. Keep safety first in your circuit designs! Mitsubishi Electric Corporation puts the maximum effort into making semiconductor products better and more reliable, but there is always the possibility that trouble may occur. Trouble with semiconductors may lead to personal injury, fire or property damage. Remember to give due consideration to safety when making your circuit designs, with appropriate measures such as (i) placement of substitutive, auxiliary circuits, (ii) use of non-flammable material, or (iii) prevention against any malfunction or mishap. RA07M2127M MITSUBISHI ELECTRIC 8/9 25 April 2003 SALES CONTACT JAPAN: GERMANY: Mitsubishi Electric Corporation Mitsubishi Electric Europe B.V. Semiconductor Sales Promotion Department Semiconductor 2-2-3 Marunouchi, Chiyoda-ku Gothaer Strasse 8 Tokyo, Japan 100 D-40880 Ratingen, Germany Email: [email protected] Email: [email protected] Phone: +81-3-3218-4854 Phone: +49-2102-486-0 Fax: +81-3-3218-4861 Fax: +49-2102-486-3670 HONG KONG: FRANCE: Mitsubishi Electric Hong Kong Ltd. Mitsubishi Electric Europe B.V. Semiconductor Division Semiconductor 41/F. Manulife Tower, 169 Electric Road 25 Boulevard des Bouvets North Point, Hong Kong F-92741 Nanterre Cedex, France Email: [email protected] Email: [email protected] Phone: +852 2510-0555 Phone: +33-1-55685-668 Fax: +852 2510-9822 Fax: +33-1-55685-739 SINGAPORE: ITALY: Mitsubishi Electric Asia PTE Ltd Mitsubishi Electric Europe B.V. Semiconductor Division Semiconductor 307 Alexandra Road Centro Direzionale Colleoni, #3-01/02 Mitsubishi Electric Building, Palazzo Perseo 2, Via Paracelso Singapore 159943 I-20041 Agrate Brianza, Milano, Italy Email: [email protected] Email: [email protected] Phone: +65 64 732 308 Phone: +39-039-6053-10 Fax: +65 64 738 984 Fax: +39-039-6053-212 TAIWAN: U.K.: Mitsubishi Electric Taiwan Company, Ltd., Mitsubishi Electric Europe B.V. Semiconductor Department Semiconductor 9F, No. 88, Sec. 6 Travellers Lane, Hatfield Chung Shan N. Road Hertfordshire, AL10 8XB, England Taipei, Taiwan, R.O.C. Email: [email protected] Email: [email protected] Phone: +44-1707-278-900 Phone: +886-2-2836-5288 Fax: +44-1707-278-837 Fax: +886-2-2833-9793 U.S.A.: AUSTRALIA: Mitsubishi Electric & Electronics USA, Inc. Mitsubishi Electric Australia, Electronic Device Group Semiconductor Division 1050 East Arques Avenue 348 Victoria Road Sunnyvale, CA 94085 Rydalmere, NSW 2116 Email: [email protected] Sydney, Australia Phone: 408-730-5900 Email: [email protected] Fax: 408-737-1129 Phone: +61 2 9684-7210 +61 2 9684 7212 +61 2 9684 7214 +61 3 9262 9898 Fax: +61 2 9684-7208 +61 2 9684 7245 CANADA: Mitsubishi Electric Sales Canada, Inc. 4299 14th Avenue Markham, Ontario, Canada L3R OJ2 Phone: 905-475-7728 Fax: 905-475-1918 RA07M2127M MITSUBISHI ELECTRIC 9/9 25 April 2003