MITSUBISHI DIODE MODULES RM50TC-M,-H,-24,-2H MEDIUM POWER GENERAL USE INSULATED TYPE RM50TC-M,-H,-24,-2H • IO • VRRM DC output current .................... 100A Repetitive peak reverse voltage .......... 400/800/1200/1600V • 3 phase bridge • Insulated Type • UL Recognized Yellow Card No. E80276 (N) File No. E80271 APPLICATION AC motor controllers , DC motor controllers, Battery DC power supplies, DC power supplies for control panels, and other general DC power equipment OUTLINE DRAWING & CIRCUIT DIAGRAM Dimensions in mm 20 40 2–φ5.5 11.5 10.5 20 10 30 5–M5 68 8 LABEL 29.5 26.5 80 Feb.1999 MITSUBISHI DIODE MODULES RM50TC-M,-H,-24,-2H MEDIUM POWER GENERAL USE INSULATED TYPE ABSOLUTE MAXIMUM RATINGS Symbol Parameter Voltage class M H 24 2H Unit VRRM Repetitive peak reverse voltage 400 800 1200 1600 V VRSM Non-repetitive peak reverse voltage 480 960 1350 1700 V Ea Recommended AC input voltage 110 220 370 440 V Ratings Unit IO DC output current Three-phase full wave rectifying circuit, TC=102°C 100 A IFSM Surge (non-repetitive) forward current One half cycle at 60Hz, peak value 1000 A I2t I2t for fusing Value for one cycle of surge current 4.2 × 103 A2s f Maximum operating frequency 1000 Hz Tj Junction temperature –40~+150 °C Tstg Storage temperature –40~+125 °C Viso Isolation voltage Parameter Symbol Conditions Charged part to case Main terminal screw M5 — Mounting torque Mounting screw M5 — Weight Typical value 2500 V 1.47~1.96 N·m 15~20 kg·cm 1.47~1.96 N·m 15~20 kg·cm 220 g ELECTRICAL CHARACTERISTICS Limits Symbol Parameter Test conditions Min. Typ. Max. Unit IRRM Repetitive reverse current Tj=150°C, VRRM applied — — 10 VFM Forward voltage Tj=25°C, IFM=100A, instantaneous meas. — — 1.2 V Rth (j-c) Thermal resistance Junction to case — — 0.2 °C/ W Rth (c-f) Contact thermal resistance Case to fin, conductive grease applied — — 0.06 °C/ W Insulation resistance Measured with a 500V megohmmeter between main terminal and case 10 — — MΩ — mA Feb.1999 MITSUBISHI DIODE MODULES RM50TC-M,-H,-24,-2H MEDIUM POWER GENERAL USE INSULATED TYPE PERFORMANCE CURVE MAXIMUM FORWARD CHARACTERISTIC 1000 Tj=25°C SURGE (NON-REPETITIVE) FORWARD CURRENT (A) FORWARD CURRENT (A) 10 3 7 5 3 2 ALLOWABLE SURGE (NON-REPETITIVE) FORWARD CURRENT 10 2 7 5 3 2 10 1 7 5 3 2 10 0 0.6 0.8 1.0 1.2 1.4 800 600 400 200 0 2.0 1 2 3 5 7 10 20 30 50 70100 CONDUCTION TIME (CYCLES AT 60Hz) MAXIMUM TRANSIENT THERMAL IMPEDANCE (JUNCTION TO CASE) 10 0 2 3 5 7 10 1 0.20 MAXIMUM POWER DISSIPATION 250 POWER DISSIPATION (W) TRANSIENT THERMAL IMPEDANCE (°C/W) FORWARD VOLTAGE (V) 0.16 0.12 0.08 0.04 0 10 –3 2 3 5 7 10 –2 2 3 5 7 10 –1 2 3 5 7 10 0 TIME (s) RESISTIVE, INDUCTIVE LOAD 200 150 100 50 0 0 20 40 60 80 100 DC OUTPUT CURRENT (A) ALLOWABLE CASE TEMPERATURE VS. DC OUTPUT CURRENT CASE TEMPERATURE (°C) 160 RESISTIVE, INDUCTIVE LOAD 140 120 100 80 60 0 20 40 60 80 100 DC OUTPUT CURRENT (A) Feb.1999