MOTOROLA MC145557

Order this document
by MC145554/D
SEMICONDUCTOR TECHNICAL DATA
The MC145554, MC145557, MC145564, and MC145567 are all per channel
PCM Codec–Filters. These devices perform the voice digitization and
reconstruction as well as the band limiting and smoothing required for PCM
systems. They are designed to operate in both synchronous and asynchronous
applications and contain an on–chip precision voltage reference. The
MC145554 (Mu–Law) and MC145557 (A–Law) are general purpose devices
that are offered in 16–pin packages. The MC145564 (Mu–Law) and MC145567
(A–Law), offered in 20–pin packages, add the capability of analog loopback and
push–pull power amplifiers with adjustable gain.
These devices have an input operational amplifier whose output is the input
to the encoder section. The encoder section immediately low–pass filters the
analog signal with an active R–C filter to eliminate very–high–frequency noise
from being modulated down to the pass band by the switched capacitor filter.
From the active R–C filter, the analog signal is converted to a differential signal.
From this point, all analog signal processing is done differentially. This allows
processing of an analog signal that is twice the amplitude allowed by a
single–ended design, which reduces the significance of noise to both the
inverted and non–inverted signal paths. Another advantage of this differential
design is that noise injected via the power supplies is a common–mode signal
that is cancelled when the inverted and non–inverted signals are recombined.
This dramatically improves the power supply rejection ratio.
After the differential converter, a differential switched capacitor filter band
passes the analog signal from 200 Hz to 3400 Hz before the signal is digitized
by the differential compressing A/D converter.
The decoder accepts PCM data and expands it using a differential D/A
converter. The output of the D/A is low–pass filtered at 3400 Hz and sinX/X
compensated by a differential switched capacitor filter. The signal is then filtered
by an active R–C filter to eliminate the out–of–band energy of the switched
capacitor filter.
These PCM Codec–Filters accept both long–frame and short–frame industry
standard clock formats. They also maintain compatibility with Motorola’s family
of TSACs and MC3419/MC34120 SLIC products.
The MC145554/57/64/67 family of PCM Codec–Filters utilizes CMOS due to
its reliable low–power performance and proven capability for complex
analog/digital VLSI functions.
MC145554/57 (16–Pin Package)
• Fully Differential Analog Circuit Design for Lowest Noise
• Performance Specified for Extended Temperature Range of – 40 to + 85°C
• Transmit Band–Pass and Receive Low–Pass Filters On–Chip
• Active R–C Pre–Filtering and Post–Filtering
• Mu–Law Companding MC145554
• A–Law Companding MC145557
• On–Chip Precision Voltage Reference (2.5 V)
• Typical Power Dissipation of 40 mW, Power Down of 1.0 mW at ± 5 V
16
L SUFFIX
CERAMIC PACKAGE
CASE 620
MC145554/57
1
P SUFFIX
PLASTIC DIP
CASE 648
MC145554/57
16
1
16
1
DW SUFFIX
SOG PACKAGE
CASE 751G
MC145554/57
L SUFFIX
CERAMIC PACKAGE
CASE 732
MC145564/67
20
1
20
1
20
1
P SUFFIX
PLASTIC DIP
CASE 738
MC145564/67
DW SUFFIX
SOG PACKAGE
CASE 751D
MC145564/67
MC145564/67 (20–Pin Package) — All of the Features of the MC145554/57 Plus:
• Mu–Law Companding MC145564
• A–Law Companding MC145567
• Push–Pull Power Drivers with External Gain Adjust
• Analog Loopback
REV 1
9/95 (Replaces ADI1517)

Motorola, Inc. 1995
MOTOROLA
MC145554•MC145557•MC145564•MC145567
1
PIN ASSIGNMENTS
MC145554, MC145557
MC145564, MC145567
VBB
1
16
VFXI +
GNDA
2
15
VFXI –
GNDA
VFRO
3
14
GSX
VPO –
VCC
4
13
TSX
FSR
5
12
DR
6
11
BCLKR/ CLKSEL
7
MCLKR/ PDN
8
20
VBB
2
19
VFXI +
3
18
VFXI –
VPI
4
17
GSX
FSX
VFRO
5
16
ANLB
DX
VCC
6
15
TSX
10
BCLKX
FSR
7
14
FSX
9
MCLKX
DR
8
13
DX
BCLKR/ CLKSEL
9
12
BCLKX
10
11
MCLKX
VPO +
1
MCLKR/ PDN
FUNCTIONAL BLOCK DIAGRAM
GSX
VFXI –
VFXI +
ANLB*
VCC
GNDA VBB
FSX
FSR MCLKX BCLKX
MCLKR/ BCLKR/
PDN
CLKSEL
INTERNAL SEQUENCING
AND CONTROL
–
RC ACTIVE
LOW–PASS
FILTER
+
5–POLE SC
LOW–PASS
FILTER
TSX
3–POLE
HIGH–PASS
AND S/H
COMP
VPO +
*
–1
BAND–GAP
VOLTAGE
REF
4
RDAC
8
SAR
REG
TRANSMIT
SHIFT
REG
DX
RECEIVE
LATCH
RECEIVE
SHIFT
REG
DR
CDAC
–
4
VPO –
*
+
VPI*
VFRO
MUX
8
RC ACTIVE
LOW–PASS
FILTER
5–POLE SC
LOW–PASS
FILTER
S/H
* MC145564 and MC145567 only.
MC145554•MC145557•MC145564•MC145567
2
MOTOROLA
PIN DESCRIPTION
DEVICE DESCRIPTION
A codec–filter is used for digitizing and reconstructing the
human voice. These devices were developed primarily for
the telephone network to facilitate voice switching and transmission. Once the voice is digitized, it may be switched by
digital switching methods or transmitted long distance (T1,
microwave, satellites, etc.) without degradation. The name
codec is an acronym from “COder” (for the A/D used to digitize voice) and “DECoder” (for the D/A used for reconstructing voice). A codec is a single device that does both the A/D
and D/A conversions.
To digitize intelligible voice requires a signal–to–distortion
ratio of about 30 dB over a dynamic range of about 40 dB.
This can be accomplished with a linear 13–bit A/D and D/A,
but will far exceed the required signal–to–distortion ratio at
amplitudes greater than 40 dB below the peak amplitude.
This excess performance is at the expense of data per sample. Methods of data reduction are implemented by compressing the 13–bit linear scheme to companded 8–bit
schemes. There are two companding schemes used:
Mu–255 Law specifically in North America, and A–Law
specifically in Europe. These companding schemes are
accepted world wide. These companding schemes follow a
segmented or “piecewise–linear” curve formatted as sign bit,
three chord bits, and four step bits. For a given chord, all sixteen of the steps have the same voltage weighting. As the
voltage of the analog input increases, the four step bits increment and carry to the three chord bits which increment.
When the chord bits increment, the step bits double their
voltage weighting. This results in an effective resolution of six
bits (sign + chord + four step bits) across a 42 dB dynamic
range (seven chords above zero, by 6 dB per chord).
Tables 3 and 4 show the linear quantization levels to PCM
words for the two companding schemes.
In a sampling environment, Nyquist theory says that to
properly sample a continuous signal, it must be sampled at a
frequency higher than twice the signal’s highest frequency
component. Voice contains spectral energy above 3 kHz, but
its absence is not detrimental to intelligibility. To reduce the
digital data rate, which is proportional to the sampling rate, a
sample rate of 8 kHz was adopted, consistent with a bandwidth of 3 kHz. This sampling requires a low–pass filter to
limit the high frequency energy above 3 kHz from distorting
the in–band signal. The telephone line is also subject to
50/60 Hz power line coupling, which must be attenuated from
the signal by a high–pass filter before the A/D converter.
The D/A process reconstructs a staircase version of the
desired in–band signal, which has spectral images of the in–
band signal modulated about the sample frequency and its
harmonics. These spectral images, called aliasing components, need to be attenuated to obtain the desired signal.
The low–pass filter used to attenuate these aliasing components is typically called a reconstruction or smoothing filter.
The MC145554/57/64/67 PCM Codec–Filters have the
codec, both presampling and reconstruction filters, and a
precision voltage reference on–chip, and require no external
components.
MOTOROLA
DIGITAL
FSR
Receive Frame Sync
This is an 8 kHz enable that must be synchronous with
BCLK R. Following a rising FS R edge, a serial PCM word at
D R is clocked by BCLK R into the receive data register. FS R
also initiates a decode on the previous PCM word. In the absence of FS X, the length of the FS R pulse is used to determine whether the I/O conforms to the Short Frame Sync or
Long Frame Sync convention.
DR
Receive Digital Data Input
BCLKR/CLKSEL
Receive Data Clock and Master Clock Frequency
Selector
If this input is a clock, it must be between 128 kHz and
4.096 MHz, and synchronous with FSR. In synchronous
applications this pin may be held at a constant level; then
BCLKX is used as the data clock for both the transmit and
receive sides, and this pin selects the assumed frequency of
the master clock (see Table 1 in Functional Description).
MCLKR/PDN
Receive Master Clock and Power–Down Control
Because of the shared DAC architecture used on these
devices, only one master clock is needed. Whenever FSX is
clocking, MCLK X is used to derive all internal clocks, and the
MCLK R /PDN pin merely serves as a power–down control. If
MCLK R /PDN pin is held low or is clocked (and at least one
of the frame syncs is present), the part is powered up. If this
pin is held high, the part is powered down. If FS X is absent
but FS R is still clocking, the device goes into receive half–
channel mode, and MCLK R (if clocking) generates the
internal clocks.
MCLKX
Transmit Master Clock
This clock is used to derive the internal sequencing clocks;
it must be 1.536 MHz, 1.544 MHz, or 2.048 MHz.
BCLKX
Transmit Data Clock
BCLK X may be any frequency between 128 kHz and
4.096 MHz, but it should be synchronous with MCLKX.
DX
Transmit Digital Data Output
This output is controlled by FS X and BCLKX to output the
PCM data word; otherwise this pin is in a high–impedance
state.
FSX
Transmit Frame Sync
This is an 8 kHz enable that must be synchronous with
BCLK X. A rising FS X edge initiates the transmission of a
MC145554•MC145557•MC145564•MC145567
3
serial PCM word, clocked by BCLK X, out of D X. If the FS X
pulse is high for more than eight BCLK X periods, the DX and
TS X outputs will remain in a low–impedance state until FS X
is brought low. The length of the FS X pulse is used to determine whether the transmit and receive digital I/O conforms to
the Short Frame Sync or to the Long Frame Sync convention.
TSX
Transmit Time Slot Indicator
This is an open–drain output that goes low whenever the
DX output is in a low–impedance state (i.e., during the transmit time slot when the PCM word is being output) for enabling a PCM bus driver.
VPO+
Voltage Power Output (Non–Inverted)
(MC145554/67 Only)
This non–inverted output of the receive push–pull power
amplifier pair can drive 300 Ω to 3.3 V peak.
POWER SUPPLY
GNDA
Analog Ground
This terminal is the reference level for all signals, both analog and digital. It is 0 V.
VCC
Positive Power Supply
VCC is typically 5 V.
ANLB
Analog Loopback Control Input (MC145564/67 Only)
When held high, this pin causes the input of the transmit
RC active filter to be disconnected from GSX and connected
to VPO + for analog loopback testing. This pin is held low in
normal operation.
ANALOG
GSX
Gain–Setting Transmit
This output of the transmit gain–adjust operational amplifier is internally connected to the encoder section of the
device. It must be used in conjunction with VFXI– and VFXI+
to set the transmit gain for a maximum signal amplitude of
2.5 V peak. This output can drive a 600 Ω load to 2.5 V peak.
VFXI–
Voice–Frequency Transmit Input (Inverting)
This is the inverting input of the transmit gain–adjust
operational amplifier.
VFXI+
Voice–Frequency Transmit Input
(Non–Inverting)
This is the non–inverting input of the transmit gain–adjust
operational amplifier.
VFRO
Voice–Frequency Receive Output
This receive analog output is capable of driving a 600 Ω
load to 2.5 V peak.
VPI
Voltage Power Input (MC145564/67 Only)
This is the inverting input to the first receive power amplifier. Both of the receive power amplifiers can be powered
down by connecting this input to VBB.
VPO–
Voltage Power Output (Inverted) (MC145564/67 Only)
This inverted output of the receive push–pull power amplifiers can drive 300 Ω to 3.3 V peak.
MC145554•MC145557•MC145564•MC145567
4
VBB
Negative Power Supply
VBB is typically – 5 V.
FUNCTIONAL DESCRIPTION
ANALOG INTERFACE AND SIGNAL PATH
The transmit portion of these codec–filters includes a low–
noise gain setting amplifier capable of driving a 600 Ω load.
Its output is fed to a three–pole anti–aliasing pre–filter. This
pre–filter incorporates a two–pole Butterworth active low–
pass filter, and a single passive pole. This pre–filter is followed by a single ended–to–differential converter that is
clocked at 256 kHz. All subsequent analog processing utilizes fully differential circuitry. The next section is a fully–differential, five–pole switched capacitor low–pass filter with a
3.4 kHz passband. After this filter is a 3–pole switched–capacitor high–pass filter having a cutoff frequency of about
200 Hz. This high–pass stage has a transmission zero at dc
that eliminates any dc coming from the analog input or from
accumulated operational amplifier offsets in the preceding filter stages. The last stage of the high–pass filter is an autozeroed sample and hold amplifier.
One bandgap voltage reference generator and digital–to–
analog converter (DAC) are shared by the transmit and
receive sections. The autozeroed, switched–capacitor bandgap reference generates precise positive and negative reference voltages that are independent of temperature and
power supply voltage. A binary–weighted capacitor array
(CDAC) forms the chords of the companding structure, while
a resistor string (RDAC) implements the linear steps within
each chord. The encode process uses the DAC, the voltage
reference, and a frame–by–frame autozeroed comparator to
implement a successive–approximation conversion algorithm. All of the analog circuitry involved in the data conversion — the voltage reference, RDAC, CDAC, and
comparator — are implemented with a differential architecture.
The receive section includes the DAC described above, a
sample and hold amplifier, a five–pole 3400 Hz switched
capacitor low–pass filter with sinX/X correction, and a two–
pole active smoothing filter to reduce the spectral components of the switched capacitor filter. The output of the
smoothing filter is a power amplifier that is capable of driving
a 600 Ω load. The MC145564 and MC145567 add a pair of
power amplifiers that are connected in a push–pull configuration; two external resistors set the gain of both of the
MOTOROLA
complementary outputs. The output of the second amplifier
may be internally connected to the input of the transmit anti–
aliasing filter by bringing the ANLB pin high. The power amplifiers can drive unbalanced 300 Ω loads or a balanced
600 Ω load; they may be powered down independent of the
rest of the chip by tying the VPI pin to VBB.
MASTER CLOCKS
Since the codec–filter design has a single DAC architecture, only one master clock is used. In normal operation (both
frame syncs clocking), the MCLKX is used as the master
clock, regardless of whether the MCLKR/PDN pin is clocking
or low. The same is true if the part is in transmit half–channel
mode (FSX clocking, FSR held low). But if the codec–filter is
in the receive half–channel mode, with FSR clocking and FSX
held low, MCLKR is used for the internal master clock if it is
clocking; if MCLKR is low, then MCLKX is still used for the
internal master clock. Since only one of the master clocks is
used at any given time, they need not be synchronous.
The master clock frequency must be 1.536 MHz,
1.544 MHz, or 2.048 MHz. The frequency that the codec–
filter expects depends upon whether the part is a Mu–Law or
an A–Law part, and on the state of the BCLKR/CLKSEL pin.
The allowable options are shown In Table 1. When a level
(rather than a clock) is provided for BCLKR/CLKSEL, BCLKX
is used as the bit clock for both transmit and receive.
Table 1. Master Clock Frequency Determination
Master Clock Frequency Expected
BCLKR/CLKSEL
MC145554/64
MC145557/67
Clocked, 1, or Open
1.536 MHz
1.544 MHz
2.048 MHz
0
2.048 MHz
1.536 MHz
1.544 MHz
FRAME SYNCS AND DIGITAL I/O
These codec–filters can accommodate both of the industry
standard timing formats. The Long Frame Sync mode is
used by Motorola’s MC145500 family of codec–filters and the
UDLT family of digital loop transceivers. The Short Frame
Sync mode is compatible with the IDL (Interchip Digital Link)
serial format used in Motorola’s ISDN family and by other
companies in their telecommunication devices. These
codec–filters use the length of the transmit frame sync (FSX)
to determine the timing format for both transmit and receive
unless the part is operating in the receive half–channel
mode.
In the Long Frame Sync mode, the frame sync pulses
must be at least three bit clock periods long. The D X and TS X
outputs are enabled by the logical ANDing of FS X and
BCLK X; when both are high, the sign bit appears at the D X
output. The next seven rising edges of BCLK X clock out the
remaining seven bits of the PCM word. The D X and TS X outputs return to a high impedance state on the falling edge of
the eighth bit clock or the falling edge of FS X, whichever
comes later. The receive PCM word is clocked into D R on the
eight falling BCLK R edges following an FSR rising edge.
For Short Frame Sync operation, the frame sync pulses
must be one bit clock period long. On the first BCLK X rising
edge after the falling edge of BCLK X has latched FS X high,
the DX and TS X outputs are enabled and the sign bit is presented on D X. The next seven rising edges of BCLK X clock
out the remaining seven bits of the PCM word; on the eighth
BCLK X falling edge, the D X and TS X outputs return to a high
impedance state. On the second falling BCLK R edge following an FS R rising edge, the receive sign bit is clocked into
D R. The next seven BCLK R falling edges clock in the remaining seven bits of the receive PCM word.
Table 2 shows the coding format of the transmit and receive PCM words.
HALF–CHANNEL MODES
In addition to the normal full–duplex operating mode, these
codec–filters can operate in both transmit and receive half–
channel modes. Transmit half–channel mode is entered by
holding FS R low. The VF R O output goes to analog ground
but remains in a low impedance state (to facilitate a hybrid
interface); PCM data at D R is ignored. Holding FS X low while
clocking FSR puts these devices in the receive half–channel
mode. In this state, the transmit input operational amplifier
continues to operate, but the rest of the transmit circuitry is
disabled; the D X and TS X outputs remain in a high impedance state. MCLK R is used as the internal master clock if it is
clocking. If MCLK R is not clocking, then MCLK X is used for
the internal master clock, but in that case it should be synchronous with FS R. If BCLK R is not clocking, BCLK X will be
used for the receive data, just as in the full–channel operating mode. In receive half–channel mode only, the length of
the FS R pulse is used to determine whether Short Frame
Sync or Long Frame Sync timing is used at DR.
POWER–DOWN
Holding both FS X and FS R low causes the part to go into
the power–down state. Power–down occurs approximately
2 ms after the last frame sync pulse is received. An alternative way to put these devices in power–down is to hold the
MCLK R /PDN pin high. When the chip is powered down, the
D X , TS X , and GS X outputs are high impedance, the VF R O,
VPO–, and VPO+ operational amplifiers are biased with a
trickle current so that their respective outputs remain stable
at analog ground. To return the chip to the power–up state,
MCLK R/PDN must be low or clocking and at least one of the
frame sync pulses must be present. The D X and TS X outputs
will remain in a high–impedance state until the second FSX
pulse after power–up.
Table 2. PCM Data Format
Mu–Law (MC145554/64)
A–Law (MC145557/67)
Level
Sign Bit
Chord Bits
Step Bits
Sign Bit
Chord Bits
Step Bits
+ Full Scale
1
000
0000
1
010
1010
+ Zero
1
111
1111
1
101
0101
– Zero
0
111
1111
0
101
0101
– Full Scale
0
000
0000
0
010
1010
MOTOROLA
MC145554•MC145557•MC145564•MC145567
5
MAXIMUM RATINGS (Voltage Referenced to GNDA)
Rating
Value
Unit
– 0.5 to + 13
– 0.3 to + 7.0
– 7.0 to + 0.3
V
Voltage on Any Analog Input or Output Pin
VBB – 0.3 to
VCC + 0.3
V
Voltage on Any Digital Input or Output Pin
GNDA – 0.3 to
VCC + 0.3
V
TA
– 40 to + 85
°C
Tstg
– 85 to + 150
°C
DC Supply Voltage
Symbol
VCC to VBB
VCC to GNDA
VBB to GNDA
Operating Temperature Range
Storage Temperature Range
This device contains circuitry to protect
against damage due to high static voltages or
electric fields; however, it is advised that
normal precautions be taken to avoid application of any voltage higher than maximum
rated voltages to this high impedance circuit.
For proper operation it is recommended that
Vin and Vout be constrained to the range VSS
≤ (Vin or Vout) ≤ VDD.
Unused inputs must always be tied to an
appropriate logic voltage level (e.g., VBB,
GNDA, or VCC).
POWER SUPPLY (TA = – 40 to + 85°C)
Characteristic
DC Supply Voltage
VCC
VBB
Min
Typ
Max
Unit
4.75
– 4.75
5.0
– 5.0
5.25
– 5.25
V
Active Power Dissipation (No Load)
MC145554/57
MC145564/67
MC145564/67, VPI = VBB
—
—
—
40
45
40
60
70
60
mW
Power–Down Dissipation (No Load)
MC145554/57
MC145564/67
MC145564/67, VPI = VBB
—
—
—
1.0
2.0
1.0
3.0
5.0
3.0
mW
Symbol
Min
Max
Unit
Input Low Voltage
VIL
—
0.6
V
Input High Voltage
VIH
2.2
—
V
DIGITAL LEVELS (VCC = 5 V ± 5%, VBB = – 5 V ± 5%, GNDA = 0 V, TA = – 40 to + 85°C)
Characteristic
Output Low Voltage
DX or TSX, IOL = 3.2 mA
VOL
—
0.4
V
Output High Voltage
DX, IOH = – 3.2 mA
IOH = – 1.6 mA
VOH
2.4
VCC – 0.5
—
—
V
Input Low Current
GNDA ≤ Vin ≤ VCC
IIL
– 10
+ 10
µA
Input High Current
GNDA ≤ Vin ≤ VCC
IIH
– 10
+ 10
µA
Output Current in High Impedance State
GNDA ≤ DX ≤ VCC
IOZ
– 10
+ 10
µA
MC145554•MC145557•MC145564•MC145567
6
MOTOROLA
ANALOG ELECTRICAL CHARACTERISTICS
(VCC = + 5 V ± 5%, VBB = – 5 V ± 5%, VFXI – Connected to GSX, TA = – 40 to + 85°C)
Characteristic
Min
Typ
Max
Unit
Input Current (– 2.5 ≤ Vin ≤ + 2.5 V)
VFXI +, VFXI –
—
± 0.05
± 0.2
µA
AC Input Impedance to GNDA (1 kHz)
VFXI +, VFXI –
10
20
—
MΩ
Input Capacitance
VFXI +, VFXI –
—
—
10
pF
Input Offset Voltage of GSX Op Amp
VFXI +, VFXI –
—
—
± 25
mV
Input Common Mode Voltage Range
VFXI +, VFXI –
– 2.5
—
2.5
V
Input Common Mode Rejection Ratio
VFXI +, VFXI –
—
65
—
dB
Unity Gain Bandwidth of GSX Op Amp (Rload ≥ 10 kΩ)
—
1000
—
kHz
DC Open Loop Gain of GSX Op Amp (Rload ≥ 10 kΩ)
75
—
—
dB
Equivalent Input Noise (C–Message) Between VFXI+ and VFXI– at GSX
—
– 20
—
dBrnC0
Output Load Capacitance for GSX Op Amp
0
—
100
pF
Rload = 10 kΩ to GNDA
Rload = 600 Ω to GNDA
– 3.5
– 2.8
—
—
+ 3.5
+ 2.8
V
GSX, VFRO
± 5.0
—
—
mA
—
1
—
Ω
Output Load Capacitance for VFRO
0
—
500
pF
VFRO Output DC Offset Voltage Referenced to GNDA
—
—
± 100
mV
Transmit Power Supply Rejection
Positive, 0 to 100 kHz, C–Message
Negative, 0 to 100 kHz, C–Message
45
45
—
—
—
—
dBC
Receive Power Supply Rejection
Positive, 0 to 100 kHz, C–Message
Positive, 4 kHz to 25 kHz
Positive, 25 kHz to 50 kHz
Negative, 0 to 100 kHz, C–Message
Negative, 4 kHz to 25 kHz
Negative, 25 kHz to 50 kHz
50
50
43
50
45
38
—
—
—
—
—
—
—
—
—
—
—
—
dBC
dB
dB
dBC
dB
dB
Input Current (– 1 V ≤ VPI ≤ + 1 V)
VPI
—
± 0.05
± 0.5
µA
Input Resistance (– 1 V ≤ VPI ≤ + 1 V)
VPI
5
10
—
MΩ
Input Offset Voltage (VPI Connected to VPO–)
VPI
—
—
± 50
mV
VPO+ or VPO–
—
1
—
Ω
VPO–
—
400
—
kHz
VPO+ or VPO– to GNDA
0
—
1000
pF
Gain from VPO– to VPO+ (Rload = 300 Ω, VPO+ to GNDA Level at VPO–
= 1.77 Vrms, +3 dBm0)
—
–1
—
V/V
Maximum 0 dBm0 Level for Better than ± 0.1 dB Linearity Over the
Range – 10 dBm0 to + 3 dBm0 (For Rload between VPO+
and VPO–)
Rload = 600 Ω
Rload = 1200 Ω
Rload = 10 kΩ
3.3
3.5
4.0
—
—
—
—
—
—
Vrms
Power Supply Rejection of VCC or VBB (VPO– Connected to VPI)
VPO + or VPO – to GNDA
0 to 4 kHz
4 to 50 kHz
55
35
—
—
—
—
dB
Differential Power Supply Rejection of VCC or VBB (VPO– Connected to VPI)
VPO+ to VPO–, 0 to 50 kHz
50
—
—
Output Voltage Range for GSX
Output Current (– 2.8 V ≤ Vout ≤ + 2.8 V)
Output Impedance VFRO (0 to 3.4 kHz)
MC145564/67 Power Drivers
Output Resistance, Inverted Unity Gain
Unity Gain Bandwidth, Open Loop
Load Capacitance (∞ Ω ≥ Rload ≥ 300 Ω)
MOTOROLA
dB
MC145554•MC145557•MC145564•MC145567
7
ANALOG TRANSMISSION PERFORMANCE
(VCC = + 5 V ± 5%, VBB = – 5 V ± 5%, GNDA = 0 V, 0 dBm0 = 1.2276 Vrms = + 4 dBm @ 600 Ω, FSX = FSR = 8 kHz,
BCLKX = MCLKX = 2.048 MHz Synchronous Operation, VFXI – Connected to GSX, TA = – 40 to + 85°C Unless Otherwise Noted)
End–to–End
Characteristic
A/D
D/A
Min
Max
Min
Max
Min
Max
Unit
Absolute Gain (0 dBm0 @ 1.02 kHz, TA = 25°C, VCC = 5 V, VBB = – 5 V)
—
—
– 0.25
– 0.25
– 0.25
+ 0.25
dB
Absolute Gain Variation with Temperature
—
—
—
—
—
—
± 0.03
± 0.06
—
—
± 0.03
± 0.06
dB
—
—
—
± 0.02
—
± 0.02
dB
0 to 70°C
– 40 to + 85°C
Absolute Gain Variation with Power Supply (VCC = 5 V, ± 5%,
VBB = – 5 V, ± 5%)
Gain vs Level Tone (Relative to – 10 dBm0, 1.02 kHz)
+ 3 to – 40 dBm0
– 40 to – 50 dBm0
– 50 to – 55 dBm0
– 0.4
– 0.8
– 1.6
+ 0.4
+ 0.8
+ 1.6
– 0.2
– 0.4
– 0.8
+ 0.2
+ 0.4
+ 0.8
– 0.2
– 0.4
– 0.8
+ 0.2
+ 0.4
+ 0.8
dB
Gain vs Level Pseudo Noise CCITT G.712
(MC145557/67 A–Law Relative to – 10 dBm0)
– 10 to – 40 dBm0
– 40 to – 50 dBm0
– 50 to – 55 dBm0
—
—
—
—
—
—
– 0.25
– 0.30
– 0.45
+ 0.25
+ 0.30
+ 0.45
– 0.25
– 0.30
– 0.45
+ 0.25
+ 0.30
+ 0.45
dB
+ 3 dBm0
0 to – 30 dBm0
– 40 dBm0
– 45 dBm0
– 55 dBm0
33
35
29
24
15
—
—
—
—
—
33
36
30
25
15
—
—
—
—
—
33
36
30
25
15
—
—
—
—
—
dBC
27.5
35
33.1
28.2
13.2
—
—
—
—
—
28
35.5
33.5
28.5
13.5
—
—
—
—
—
28.5
36
34.2
30
15
—
—
—
—
—
dB
—
—
15
– 70
—
—
15
– 70
—
—
7
– 83
dBrnC0
dBm0p
Total Distortion, 1.02 kHz Tone (C–Message)
Total Distortion With Pseudo Noise CCITT G.714
(MC145557/67 A–Law)
– 3 dBm0
– 6 to – 27 dBm0
– 34 dBm0
– 40 dBm0
– 55 dBm0
Idle Channel Noise (For End–End and A/D, Note 1)
(MC145554/64 Mu–Law, C–Message Weighted)
(MC145557/67 A–Law, Psophometric Weighted)
Frequency Response (Relative to 1.02 kHz @ 0 dBm0)
15 Hz
50 Hz
60 Hz
200 Hz
300 to 3000 Hz
3300 Hz
3400 Hz
4000 Hz
4600 Hz
—
—
—
—
– 0.3
– 0.70
– 1.6
—
—
– 40
– 30
– 26
—
0.3
+ 0.3
0
– 28
– 60
—
—
—
– 1.0
– 0.15
– 0.35
– 0.8
—
—
– 40
– 30
– 26
– 0.4
+ 0.15
+ 0.15
0
– 14
– 32
– 0.15
– 0.15
– 0.15
– 0.15
– 0.15
– 0.35
– 0.8
—
—
0
0
0
0
+ 0.15
+ 0.15
0
– 14
– 30
dB
In–Band Spurious
(1.02 kHz @ 0 dBm0, Transmit and Receive)
300 to 3000 Hz
—
– 48
—
– 48
—
– 48
dBm0
Out–of–Band Spurious at VFRO (300 – 3400 Hz @ 0 dBm0 In)
4600 to 7600 Hz
7600 to 8400 Hz
8400 to 100,000 Hz
—
—
—
– 30
– 40
– 30
—
—
—
—
—
—
—
—
—
– 30
– 40
– 30
Idle Channel Noise Selective (8 kHz, Input = GNDA, 30 Hz Bandwidth)
—
– 70
—
—
—
– 70
dBm0
Absolute Delay (1600 Hz)
—
—
—
315
—
215
µs
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
220
145
75
40
75
105
155
– 40
– 40
– 40
– 30
—
—
—
—
—
—
—
90
125
175
µs
Crosstalk of 1020 Hz @ 0 dBm0 from A/D or D/A (Note 2)
—
—
—
– 75
—
– 75
dB
Intermodulation Distortion of Two Frequencies of Amplitudes
– 4 to – 21 dBm0 from the Range 300 to 3400 Hz
—
– 41
—
– 41
—
– 41
dB
Group Delay Referenced to 1600 Hz
500 to 600 Hz
600 to 800 Hz
800 to 1000 Hz
1000 to 1600 Hz
1600 to 2600 Hz
2600 to 2800 Hz
2800 to 3000 Hz
dB
NOTES:
1. Extrapolated from a 1020 Hz @ – 50 dBm0 distortion measurement to correct for encoder enhancement.
2. Selectively measured while the A/D is stimulated with 2667 Hz @ – 50 dBm0.
MC145554•MC145557•MC145564•MC145567
8
MOTOROLA
DIGITAL SWITCHING CHARACTERISTICS
(VCC = 5 V ± 5%, VBB = – 5 V ± 5%, GNDA = 0 V, All Signals Referenced to GNDA; TA = – 40 to + 85°C, Cload = 150 pF Unless Otherwise
Noted)
Characteristic
Symbol
Min
Typ
Max
Unit
Master Clock Frequency
MCLKX or MCLKR
fM
—
—
—
1.536
1.544
2.048
—
—
—
MHz
Minimum Pulse Width High or Low
MCLKX or MCLKR
tw(M)
100
—
—
ns
Minimum Pulse Width High or Low
BCLKX or BCLKR
tw(B)
50
—
—
ns
FSX or FSR
Minimum Pulse WIdth Low
tw(FL)
50
—
—
ns
Rise Time for all Digital Signals
tr
—
—
50
ns
Fall Time for all Digital Signals
tf
—
—
50
ns
fB
128
—
4096
kHz
Setup Time from BCLKX Low to MCLKR High
tsu(BRM)
50
—
—
ns
Setup Time from MCLKX High to BCLKX Low
tsu(MFB)
20
—
—
ns
Hold Time from BCLKX (BCLKR) Low to FSX (FSR) High
th(BF)
20
—
—
ns
Setup Time for FSX (FSR) High to BCLKX (BCLKR) Low for Long Frame
tsu(FB)
80
—
—
ns
Delay Time from BCLKX High to DX Data Valid
td(BD)
20
60
140
ns
Delay Time from BCLKX High to TSX Low
td(BTS)
20
50
140
ns
Delay Time from the 8th BCLKX Low of FSX Low to DX Output Disabled
td(ZC)
50
70
140
ns
Delay Time to Valid Data from FSX or BCLKX, Whichever is Later
td(ZF)
20
60
140
ns
Bit Clock Data Rate
BCLKX or BCLKR
Setup Time from DR Valid to BCLKX Low
tsu(DB)
0
—
—
ns
Hold Time from BCLKR Low to DR Invalid
th(BD)
50
—
—
ns
Setup Time from FSX (FSR) High to BCLKX (BCLKR) Low in Short Frame
tsu(F)
50
—
—
ns
Hold Time from BCLKX (BCLKR) Low to FSX (FSR) Low in Short Frame
th(F)
50
—
—
ns
Hold Time from 2nd Period of BCLKX (BCLKR) Low to FSX (FSR) Low in
Long Frame
th(BFI)
50
—
—
ns
MOTOROLA
MC145554•MC145557•MC145564•MC145567
9
TSX
td(BTS)
tw(M)
tw(M)
td(ZC)
MCLKX
MCLKR
tsu(MFB)
tw(B)
tw(B)
tsu(BRM)
BCLKX
1
th(BF)
tsu(F)
2
3
4
5
6
8
7
9
th(F)
FSX
td(ZC)
td(BD)
MSB
DX
BCLKR
1
th(BF)
CH1
2
CH2
3
CH3
4
ST1
5
ST2
6
ST3
7
LSB
8
9
th(F)
tsu(F)
FSR
th(BD)
th(BD)
tsu(DB)
DR
MSB
CH1
CH2
CH3
ST1
ST2
ST3
LSB
Figure 1. Short Frame Sync Timing
MC145554•MC145557•MC145564•MC145567
10
MOTOROLA
MCLKX
MCLKR
tsu(MFB)
tsu(BRM)
BCLKX
2
1
3
tsu(FB)
4
5
6
8
7
9
th(BFI)
th(BF)
FSX
td(ZF)
td(BD)
td(ZC)
td(ZC)
td(ZF)
DX
MSB
1
BCLKR
CH1
2
CH2
3
th(BF)
CH3
4
ST1
5
ST3
ST2
6
7
LSB
8
9
th(BFI)
tsu(FB)
FSR
th(BD)
th(BD)
tsu(DB)
DR
MSB
CH1
CH2
CH3
ST1
ST2
ST3
LSB
Figure 2. Long Frame Sync Timing
MOTOROLA
MC145554•MC145557•MC145564•MC145567
11
–5V
1
2
ANALOG OUT
+5V
3
VFXI +
VBB
GNDA
VFRO
4
VCC
MC145554/57
5
FSR
6
DR
7
BCLKR/ CLKSEL
8
MCLKR/ PDN
16
15
VFXI –
14
GSX
13
TSX
12
FSX
11
DX
10
BCLKX
9
MCLKX
ANALOG IN
TX TIME SLOT
8 kHz
1
2
3
1.544 MHz/
2.048 MHz
ADCPM IN
POWER–DOWN
4
5
6
MODE
VDD
DDO
EDO
DDE
EOE
DDC
DDI
DIE
7
PD/RESET
8 V
SS
MC145532
16
+5V
15
14
ADPCM OUT
13
EDC
12
EDI
11
EIE
10
SPC
9
ADP
20.48 MHz
Figure 3. ADPCM Transcoder Application
MC145554•MC145557•MC145564•MC145567
12
MOTOROLA
MC33120
20
19
1N4002
18
MJD253
15
VDD
VCC
EP PDI/ST2 12
13
ST1
BP
14
VDG
1N4002
– 48 V
0.01 µF
50 V
VAG
100
1/4 W
1k
17
9.1 k 16
TIP
9.1 k
RING
1k
5
4
+5V
+
RXI
+5V
MC145554/7
CN
RFO
10
MJD243
1N4002
3
2
– 48 V
20.6 k
47.4 k
1
BN
CF
EN
VQB
VEE
1 µF
11
49.0 k 16
300 Ω
6
+
20 Ω
15
14
10 k
7
1.0 µF, 50 V
10 µF, 50 V
VFRO
FSX
FSR
1 µF
TXO
1N4002
3
8
100
1/4 W
0.01 µF
50 V
VCC
48.5 k
4.7 k
RSI
5 µF, 16 V
9
CP
TSI
HOOK STATUS/
FAULT INDICATION
2
4
12
8 kHz SYNC
5
10
BCLKX
7
BCLKR
8
MCLKR
9
MCLKX
11
DX
VFXI–
6
DR
GSX
13
VFXI+
TSX
1
GNDA
VBB
DATA CLOCK
MC145554 =
1.544 MHZ
MC145557 =
2.048 MHz
TO PCM HWY
–5V
+
NOTE: Six resistors and two capacitors on the two–wire side can be 5% tolerance.
Figure 4. A Complete Single Party Channel Unit Using MC145554/57 PCM Codec–Filter and MC33120 SLIC
MOTOROLA
MC145554•MC145557•MC145564•MC145567
13
“S” TRANSCEIVER
MC145474P
+5V
17
33 k
2
+5V
S INTERFACE
7Ω
VDD
ISET
TE/NT
SYNC
7Ω
21
TX+
CLK
+5V
7Ω
RX
7Ω
20
TX
TX–
DREQ
+5V
DGRT
1 kΩ
1 kΩ
2
SEL
RX+
CLK
+5V
RX
1 kΩ
1 kΩ
3
6
RX–
VSS
XTAL
TX
IRQ
RESET
EXTAL
4
8
9
10
11
7
5
15
14
13
12
19
15.36 MHz
30 pF
HANDSET
RJ–1
1
+ RCVR
(WHITE)
3
+5V
500 Ω
+ MIC (RED)
– RCVR
(WHITE)
– MIC (BLK)
MC145554P
500 Ω
10 kΩ
15
14
0.1 µF
16
2
VFRO
VFXI–
GSX
VFXI+
GNDA
30 pF
+5V
4
VCC
12, 5
FSX, FSR
10, 7, 8, 9
MCLK, BCLK
11
DX
6
DR
13
TSX
1
VBB
CODEC–FILTER
LAP–D/LAP–B CONTROLLER
MC145488
52, 2, 9
D0 10
VDD
D1 11
D2 12
60, 44
SYNC 0, 1 D3 13
59, 45
CLK 0, 1
D4 14
55, 49
D5 15
TX 0, 1
D6 16
56, 48
RX 0, 1
D7 17
47
DREQ 1
D8 18
46
D9 19
DGNT 1
D10 20
50 SCPE 1
D11 22
D12 23
53
SCPE 0
D13 24
57
SCP CLK D14 25
54
D15 26
MPU
SCP TXD
A1 8
58
BUS
SCP RXD
A2 7
A3 6
A4 5
A5 4
A6 3
A7 1
A8 68
A9 67
A10 66
A11 65
A12 64
A13 63
A14 62
A15 61
OWN0 42
OWN1 43
MCLK 27
CS 28
R/W 29
AS 30
LDS 31
UDS 32
RST 33
IACK 34
IRQ 36
DTACK 37
BERR 38
BR 39
51, 36, 21
VSS
BG 40
BGACK 41
+5V +5V
–5V
Figure 5. ISDN Voice/Data Terminal
MC145554•MC145557•MC145564•MC145567
14
MOTOROLA
Table 3. Mu–Law Encode–Decode Characteristics
Chord
Number
Number
of Steps
Step
Size
Normalized
Encode
Decision
Levels
Digital Code
1
2
3
4
5
6
7
8
Sign
Chord
Chord
Chord
Step
Step
Step
Step
Normalized
Decode
Levels
1
0
0
0
0
0
0
0
8031
1
0
0
0
1
1
1
1
4191
1
0
0
1
1
1
1
1
2079
1
0
1
0
1
1
1
1
1023
1
0
1
1
1
1
1
1
495
1
1
0
0
1
1
1
1
231
1
1
0
1
1
1
1
1
1
1
1
0
1
1
1
1
1
1
1
1
1
1
1
0
2
1
1
1
1
1
1
1
1
0
8159
256
…
16
…
8
…
7903
4319
7
16
128
…
…
…
4063
2143
6
16
64
…
…
…
2015
1055
5
16
32
…
…
…
991
511
4
16
16
…
…
…
479
239
3
16
8
…
…
…
223
103
99
2
16
4
…
…
…
95
35
33
1
15
2
…
…
…
31
3
1
1
1
0
NOTES:
1. Characteristics are symmetrical about analog zero with sign bit = 0 for negative analog values.
2. Digital code includes inversion of all magnitude bits.
MOTOROLA
MC145554•MC145557•MC145564•MC145567
15
Table 4. A–Law Encode–Decode Characteristics
Chord
Number
Number
of Steps
Step
Size
Normalized
Encode
Decision
Levels
Digital Code
1
2
3
4
5
6
7
8
Sign
Chord
Chord
Chord
Step
Step
Step
Step
Normalized
Decode
Levels
1
0
1
0
1
0
1
0
4032
1
0
1
0
0
1
0
1
2112
1
0
1
1
0
1
0
1
1056
1
0
0
0
0
1
0
1
528
1
0
0
1
0
1
0
1
264
1
1
1
0
0
1
0
1
132
1
1
1
1
0
1
0
1
1
1
0
1
0
1
0
1
4096
128
…
16
…
7
…
3968
2176
6
16
64
…
…
…
2048
1088
5
16
32
…
…
…
1024
544
4
16
16
…
…
…
512
272
3
16
8
…
…
…
256
136
2
16
4
…
…
…
128
68
66
1
32
2
…
…
…
64
2
1
0
NOTES:
1. Characteristics are symmetrical about analog zero with sign bit = 0 for negative analog values.
2. Digital code includes alternate bit inversion, as specified by CCITT.
MC145554•MC145557•MC145564•MC145567
16
MOTOROLA
PACKAGE DIMENSIONS
L SUFFIX
CERAMIC PACKAGE
CASE 620–09
(MC145554/57)
-A16
9
1
8
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. DIMENSION L TO CENTER OF LEAD WHEN
FORMED PARALLEL.
4. DIMENSION F MAY NARROW TO 0.76 (0.030)
WHERE THE LEAD ENTERS THE CERAMIC
BODY.
-BL
C
DIM
A
B
C
D
E
F
G
J
K
L
M
N
-TK
SEATING
PLANE
M
N
E
J 16 PL
G
D 16 PL
F
0.25 (0.010)
0.25 (0.010)
M
T A
M
T B
S
INCHES
MIN
MAX
0.750 0.770
0.240 0.290
—
0.165
0.015 0.021
0.050 BSC
0.055 0.070
0.100 BSC
0.009
0.011
—
0.200
0.300 BSC
0°
15°
0.015 0.035
MILLIMETERS
MIN
MAX
19.05 19.55
7.36
6.10
4.19
—
0.53
0.39
1.27 BSC
1.77
1.40
2.54 BSC
0.27
0.23
5.08
—
7.62 BSC
15°
0°
0.39
0.88
S
P SUFFIX
PLASTIC DIP
CASE 648–08
(MC145554/57)
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. DIMENSION L TO CENTER OF LEADS WHEN
FORMED PARALLEL.
4. DIMENSION B DOES NOT INCLUDE MOLD FLASH.
5. ROUNDED CORNERS OPTIONAL.
–A–
16
9
1
8
B
F
C
L
S
–T–
K
H
G
D
J
16 PL
0.25 (0.010)
MOTOROLA
SEATING
PLANE
M
T A
M
M
DIM
A
B
C
D
F
G
H
J
K
L
M
S
INCHES
MIN
MAX
0.740
0.770
0.250
0.270
0.145
0.175
0.015
0.021
0.040
0.70
0.100 BSC
0.050 BSC
0.008
0.015
0.110
0.130
0.295
0.305
0_
10 _
0.020
0.040
MILLIMETERS
MIN
MAX
18.80
19.55
6.35
6.85
3.69
4.44
0.39
0.53
1.02
1.77
2.54 BSC
1.27 BSC
0.21
0.38
2.80
3.30
7.50
7.74
0_
10 _
0.51
1.01
MC145554•MC145557•MC145564•MC145567
17
DW SUFFIX
SOG PACKAGE
CASE 751G–02
(MC145554/57)
–A–
16
9
–B–
8X
P
0.010 (0.25)
1
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSIONS A AND B DO NOT INCLUDE MOLD
PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER
SIDE.
5. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.13 (0.005) TOTAL IN
EXCESS OF D DIMENSION AT MAXIMUM
MATERIAL CONDITION.
M
B
M
8
16X
J
D
0.010 (0.25)
M
T A
S
B
S
F
R X 45 _
C
–T–
14X
G
M
SEATING
PLANE
K
DIM
A
B
C
D
F
G
J
K
M
P
R
MILLIMETERS
MIN
MAX
10.15
10.45
7.40
7.60
2.35
2.65
0.35
0.49
0.50
0.90
1.27 BSC
0.25
0.32
0.10
0.25
0_
7_
10.05
10.55
0.25
0.75
INCHES
MIN
MAX
0.400
0.411
0.292
0.299
0.093
0.104
0.014
0.019
0.020
0.035
0.050 BSC
0.010
0.012
0.004
0.009
0_
7_
0.395
0.415
0.010
0.029
L SUFFIX
CERAMIC PACKAGE
CASE 732–03
(MC145564/67)
20
11
1
10
NOTES:
1. LEADS WITHIN 0.25 (0.010) DIAMETER, TRUE
POSITION AT SEATING PLANE, AT MAXIMUM
MATERIAL CONDITION.
2. DIMENSION L TO CENTER OF LEADS WHEN
FORMED PARALLEL.
3. DIMENSIONS A AND B INCLUDE MENISCUS.
B
A
L
C
F
N
H
D
G
K
J
M
DIM
A
B
C
D
F
G
H
J
K
L
M
N
MILLIMETERS
MIN
MAX
23.88
25.15
6.60
7.49
3.81
5.08
0.38
0.56
1.40
1.65
2.54 BSC
0.51
1.27
0.20
0.30
3.18
4.06
7.62 BSC
0_
15 _
0.25
1.02
INCHES
MIN
MAX
0.940
0.990
0.260
0.295
0.150
0.200
0.015
0.022
0.055
0.065
0.100 BSC
0.020
0.050
0.008
0.012
0.125
0.160
0.300 BSC
0_
15_
0.010
0.040
SEATING
PLANE
MC145554•MC145557•MC145564•MC145567
18
MOTOROLA
P SUFFIX
PLASTIC DIP
CASE 738–03
(MC145564/67)
-A20
11
1
10
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. DIMENSION L TO CENTER OF LEAD WHEN
FORMED PARALLEL.
4. DIMENSION B DOES NOT INCLUDE MOLD
FLASH.
B
C
-T-
L
DIM
A
B
C
D
E
F
G
J
K
L
M
N
K
SEATING
PLANE
M
E
G
N
F
J 20 PL
0.25 (0.010)
D 20 PL
0.25 (0.010)
M
T A
M
T B
M
M
INCHES
MIN
MAX
1.010 1.070
0.240 0.260
0.150 0.180
0.015 0.022
0.050 BSC
0.050 0.070
0.100 BSC
0.008 0.015
0.110 0.140
0.300 BSC
15°
0°
0.020 0.040
MILLIMETERS
MIN
MAX
25.66 27.17
6.10
6.60
3.81
4.57
0.39
0.55
1.27 BSC
1.27
1.77
2.54 BSC
0.21
0.38
2.80
3.55
7.62 BSC
0°
15°
1.01
0.51
DW SUFFIX
SOG PACKAGE
CASE 751D–04
(MC145564/67)
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSIONS A AND B DO NOT INCLUDE
MOLD PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.150
(0.006) PER SIDE.
5. DIMENSION D DOES NOT INCLUDE
DAMBAR PROTRUSION. ALLOWABLE
DAMBAR PROTRUSION SHALL BE 0.13
(0.005) TOTAL IN EXCESS OF D DIMENSION
AT MAXIMUM MATERIAL CONDITION.
–A–
20
11
–B–
10X
P
0.010 (0.25)
1
M
B
M
10
20X
D
0.010 (0.25)
M
T A
B
S
J
S
F
R
C
–T–
18X
MOTOROLA
G
K
SEATING
PLANE
X 45 _
DIM
A
B
C
D
F
G
J
K
M
P
R
MILLIMETERS
MIN
MAX
12.65
12.95
7.40
7.60
2.35
2.65
0.35
0.49
0.50
0.90
1.27 BSC
0.25
0.32
0.10
0.25
0_
7_
10.05
10.55
0.25
0.75
INCHES
MIN
MAX
0.499
0.510
0.292
0.299
0.093
0.104
0.014
0.019
0.020
0.035
0.050 BSC
0.010
0.012
0.004
0.009
0_
7_
0.395
0.415
0.010
0.029
M
MC145554•MC145557•MC145564•MC145567
19
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding
the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit,
and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters can and do vary in different
applications. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. Motorola does
not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in
systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of
the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such
unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless
against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part.
Motorola and
are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer.
How to reach us:
USA/EUROPE: Motorola Literature Distribution;
P.O. Box 20912; Phoenix, Arizona 85036. 1–800–441–2447
JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, Toshikatsu Otsuki,
6F Seibu–Butsuryu–Center, 3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 03–3521–8315
MFAX: [email protected] – TOUCHTONE (602) 244–6609
INTERNET: http://Design–NET.com
HONG KONG: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park,
51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298
◊
MC145554•MC145557•MC145564•MC145567
20
*MC145554/D*
MC145554/D
MOTOROLA