Order this document by MTD20P06HDL/D SEMICONDUCTOR TECHNICAL DATA ! Motorola Preferred Device TMOS POWER FET LOGIC LEVEL 15 AMPERES 60 VOLTS RDS(on) = 175 MΩ P–Channel Enhancement–Mode Silicon Gate This advanced high–cell density HDTMOS E–FET is designed to withstand high energy in the avalanche and commutation modes. The new energy efficient design also offers a drain–to–source diode with a fast recovery time. Designed for low–voltage, high–speed switching applications in power supplies, converters and PWM motor controls, and other inductive loads. The avalanche energy capability is specified to eliminate the guesswork in designs where inductive loads are switched, and to offer additional safety margin against unexpected voltage transients. • • • • • Ultra Low RDS(on), High–Cell Density, HDTMOS Diode is Characterized for Use in Bridge Circuits IDSS and VDS(on) Specified at Elevated Temperature Avalanche Energy Specified Surface Mount Package Available in 16 mm, 13–inch/2500 Unit, Tape & Reel, Add T4 Suffix to Part Number D G CASE 369A–13, Style 2 DPAK S MAXIMUM RATINGS (TC = 25°C unless otherwise noted) Symbol Value Unit Drain–Source Voltage Rating VDSS 60 Vdc Drain–Gate Voltage (RGS = 1.0 MΩ) VDGR 60 Vdc Gate–Source Voltage — Continuous Gate–Source Voltage — Non–Repetitive (tp ≤ 10 ms) VGS VGSM ± 15 ± 20 Vdc Vpk Drain Current — Continuous Drain Current — Continuous @ 100°C Drain Current — Single Pulse (tp ≤ 10 µs) ID ID IDM 15 9.0 45 Adc Total Power Dissipation Derate above 25°C Total Power Dissipation @ TC = 25°C (1) PD 72 0.58 1.75 Watts W/°C Watts TJ, Tstg – 55 to 150 °C Single Pulse Drain–to–Source Avalanche Energy — Starting TJ = 25°C (VDD = 25 Vdc, VGS = 5.0 Vdc, IL = 15 Apk, L = 2.7 mH, RG = 25 Ω) EAS 300 mJ Thermal Resistance — Junction to Case Thermal Resistance — Junction to Ambient Thermal Resistance — Junction to Ambient (1) RθJC RθJA RθJA 1.73 100 71.4 °C/W TL 260 °C Operating and Storage Temperature Range Maximum Temperature for Soldering Purposes, 1/8″ from case for 10 seconds Apk (1) When surface mounted to an FR4 board using the minimum recommended pad size. Designer’s Data for “Worst Case” Conditions — The Designer’s Data Sheet permits the design of most circuits entirely from the information presented. SOA Limit curves — representing boundaries on device characteristics — are given to facilitate “worst case” design. Designer’s, E–FET and HDTMOS are trademarks of Motorola Inc. TMOS is a registered trademark of Motorola Inc. Thermal Clad is a trademark of the Bergquist Company. Preferred devices are Motorola recommended choices for future use and best overall value. REV 1 TMOS Motorola Motorola, Inc. 1995 Power MOSFET Transistor Device Data 1 MTD20P06HDL ELECTRICAL CHARACTERISTICS (TJ = 25°C unless otherwise noted) Characteristic Symbol Min Typ Max Unit 60 — — 81.3 — — — — — — 1.0 10 — — 100 1.0 — 1.7 3.9 2.0 — mV/°C — 143 175 mΩ — — 2.3 1.6 3.0 2.0 gFS 9.0 11 — mhos pF OFF CHARACTERISTICS Drain–Source Breakdown Voltage (VGS = 0 Vdc, ID = 250 µAdc) Temperature Coefficient (Positive) V(BR)DSS Zero Gate Voltage Drain Current (VDS = 60 Vdc, VGS = 0 Vdc) (VDS = 60 Vdc, VGS = 0 Vdc, TJ = 125°C) IDSS Gate–Body Leakage Current (VGS = ±15 Vdc, VDS = 0) IGSS Vdc mV/°C µAdc nAdc ON CHARACTERISTICS (1) Gate Threshold Voltage (VDS = VGS, ID = 250 µAdc) Temperature Coefficient (Negative) VGS(th) Static Drain–Source On–Resistance (VGS = 5.0 Vdc, ID = 7.5 Adc) RDS(on) Drain–Source On–Voltage (VGS = 5.0 Vdc) (ID = 15 Adc) (ID = 7.5 Adc, TJ = 125°C) VDS(on) Forward Transconductance (VDS = 10 Vdc, ID = 7.5 Adc) Vdc Vdc DYNAMIC CHARACTERISTICS Input Capacitance Output Capacitance (VDS = 25 Vdc, VGS = 0 Vdc, f = 1.0 MHz) Reverse Transfer Capacitance Ciss — 850 1190 Coss — 210 290 Crss — 66 130 td(on) — 19 38 SWITCHING CHARACTERISTICS (2) Turn–On Delay Time Rise Time Turn–Off Delay Time (VDS = 30 Vdc, ID = 15 Adc, VGS = 5.0 Vdc, RG = 9.1 Ω) Fall Time Gate Charge (VDS = 48 Vdc, ID = 15 Adc, VGS = 5.0 Vdc) tr — 175 350 td(off) — 41 82 tf — 68 136 QT — 20.6 29 Q1 — 3.7 — Q2 — 7.6 — Q3 — 8.4 — — — 2.5 1.9 3.0 — trr — 64 — ta — 50 — ns nC SOURCE–DRAIN DIODE CHARACTERISTICS Forward On–Voltage (IS = 15 Adc, VGS = 0 Vdc) (IS = 15 Adc, VGS = 0 Vdc, TJ = 125°C) Reverse Recovery Time (IS = 15 Adc, VGS = 0 Vdc, dIS/dt = 100 A/µs) VSD Vdc ns tb — 14 — QRR — 0.177 — µC Internal Drain Inductance (Measured from the drain lead 0.25″ from package to center of die) LD — 4.5 — nH Internal Source Inductance (Measured from the source lead 0.25″ from package to source bond pad) LS — 7.5 — nH Reverse Recovery Stored Charge INTERNAL PACKAGE INDUCTANCE (1) Pulse Test: Pulse Width ≤ 300 µs, Duty Cycle ≤ 2%. (2) Switching characteristics are independent of operating junction temperature. 2 Motorola TMOS Power MOSFET Transistor Device Data MTD20P06HDL TYPICAL ELECTRICAL CHARACTERISTICS 30 VGS = 10 V TJ = 25°C 30 9V 20 15 6V 10 5V 5 4V 0 1 0.40 2 3 4 5 6 7 8 9 VDS ≥ 5 V 25 25°C TJ = – 55°C 20 100°C 15 10 5 0 10 2 1 4 3 5 6 VDS, DRAIN–TO–SOURCE VOLTAGE (VOLTS) VGS, GATE–TO–SOURCE VOLTAGE (VOLTS) Figure 1. On–Region Characteristics Figure 2. Transfer Characteristics VGS = 5 V 0.32 0.24 TJ = 100°C 25°C 0.16 – 55°C 0.08 0 0 5 10 15 20 25 30 0.275 TJ = 25°C 0.250 0.225 0.200 0.175 VGS = 5 V 0.150 10 V 0.125 0.100 0 5 10 15 20 25 30 ID, DRAIN CURRENT (AMPS) ID, DRAIN CURRENT (AMPS) Figure 3. On–Resistance versus Drain Current and Temperature Figure 4. On–Resistance versus Drain Current and Gate Voltage 100 1.8 1.6 VGS = 0 V VGS = 5 V ID = 7.5 A 1.4 I DSS, LEAKAGE (nA) RDS(on) , DRAIN–TO–SOURCE RESISTANCE (OHMS) 0 R DS(on) , DRAIN–TO–SOURCE RESISTANCE (NORMALIZED) 7V RDS(on) , DRAIN–TO–SOURCE RESISTANCE (OHMS) I D , DRAIN CURRENT (AMPS) 25 I D , DRAIN CURRENT (AMPS) 8V 1.2 1 0.8 0.6 TJ = 125°C 10 100°C 0.4 0.2 0 – 50 – 25 0 25 50 75 100 125 150 1 0 10 20 30 40 50 TJ, JUNCTION TEMPERATURE (°C) VDS, DRAIN–TO–SOURCE VOLTAGE (VOLTS) Figure 5. On–Resistance Variation with Temperature Figure 6. Drain–To–Source Leakage Current versus Voltage Motorola TMOS Power MOSFET Transistor Device Data 60 3 MTD20P06HDL POWER MOSFET SWITCHING Switching behavior is most easily modeled and predicted by recognizing that the power MOSFET is charge controlled. The lengths of various switching intervals (∆t) are determined by how fast the FET input capacitance can be charged by current from the generator. The capacitance (Ciss) is read from the capacitance curve at a voltage corresponding to the off–state condition when calculating td(on) and is read at a voltage corresponding to the on–state when calculating td(off). The published capacitance data is difficult to use for calculating rise and fall because drain–gate capacitance varies greatly with applied voltage. Accordingly, gate charge data is used. In most cases, a satisfactory estimate of average input current (IG(AV)) can be made from a rudimentary analysis of the drive circuit so that At high switching speeds, parasitic circuit elements complicate the analysis. The inductance of the MOSFET source lead, inside the package and in the circuit wiring which is common to both the drain and gate current paths, produces a voltage at the source which reduces the gate drive current. The voltage is determined by Ldi/dt, but since di/dt is a function of drain current, the mathematical solution is complex. The MOSFET output capacitance also complicates the mathematics. And finally, MOSFETs have finite internal gate resistance which effectively adds to the resistance of the driving source, but the internal resistance is difficult to measure and, consequently, is not specified. The resistive switching time variation versus gate resistance (Figure 9) shows how typical switching performance is affected by the parasitic circuit elements. If the parasitics were not present, the slope of the curves would maintain a value of unity regardless of the switching speed. The circuit used to obtain the data is constructed to minimize common inductance in the drain and gate circuit loops and is believed readily achievable with board mounted components. Most power electronic loads are inductive; the data in the figure is taken with a resistive load, which approximates an optimally snubbed inductive load. Power MOSFETs may be safely operated into an inductive load; however, snubbing reduces switching losses. t = Q/IG(AV) During the rise and fall time interval when switching a resistive load, VGS remains virtually constant at a level known as the plateau voltage, VSGP. Therefore, rise and fall times may be approximated by the following: tr = Q2 x RG/(VGG – VGSP) tf = Q2 x RG/VGSP where VGG = the gate drive voltage, which varies from zero to VGG RG = the gate drive resistance and Q2 and VGSP are read from the gate charge curve. During the turn–on and turn–off delay times, gate current is not constant. The simplest calculation uses appropriate values from the capacitance curves in a standard equation for voltage change in an RC network. The equations are: td(on) = RG Ciss In [VGG/(VGG – VGSP)] td(off) = RG Ciss In (VGG/VGSP) 2500 VDS = 0 V TJ = 25°C VGS = 0 V Ciss C, CAPACITANCE (pF) 2000 1500 Crss Ciss 1000 500 Coss Crss 0 10 5 5 0 VGS 10 15 20 25 VDS GATE–TO–SOURCE OR DRAIN–TO–SOURCE VOLTAGE (Volts) Figure 7. Capacitance Variation 4 Motorola TMOS Power MOSFET Transistor Device Data 50 QT 45 5 40 35 4 VDS 30 VGS 3 25 Q1 Q2 2 15 10 1 0 20 ID = 15 A TJ = 25°C Q3 0 4 5 8 12 16 0 24 20 1000 VDD = 30 V ID = 15 A VGS = 5.0 V TJ = 25°C 100 tr tf t, TIME (ns) 6 VDS , DRAIN–TO–SOURCE VOLTAGE (VOLTS) VGS, GATE–TO–SOURCE VOLTAGE (VOLTS) MTD20P06HDL td(off) td(on) 10 1 1 10 QG, TOTAL GATE CHARGE (nC) RG, GATE RESISTANCE (Ohms) Figure 8. Gate–To–Source and Drain–To–Source Voltage versus Total Charge Figure 9. Resistive Switching Time Variation versus Gate Resistance 100 DRAIN–TO–SOURCE DIODE CHARACTERISTICS The switching characteristics of a MOSFET body diode are very important in systems using it as a freewheeling or commutating diode. Of particular interest are the reverse recovery characteristics which play a major role in determining switching losses, radiated noise, EMI and RFI. System switching losses are largely due to the nature of the body diode itself. The body diode is a minority carrier device, therefore it has a finite reverse recovery time, trr, due to the storage of minority carrier charge, QRR, as shown in the typical reverse recovery wave form of Figure 12. It is this stored charge that, when cleared from the diode, passes through a potential and defines an energy loss. Obviously, repeatedly forcing the diode through reverse recovery further increases switching losses. Therefore, one would like a diode with short t rr and low QRR specifications to minimize these losses. The abruptness of diode reverse recovery effects the amount of radiated noise, voltage spikes, and current ringing. The mechanisms at work are finite irremovable circuit parasitic inductances and capacitances acted upon by high di/dts. The diode’s negative di/dt during ta is directly controlled by the device clearing the stored charge. However, the positive di/dt during tb is an uncontrollable diode characteristic and is usually the culprit that induces current ringing. Therefore, when comparing diodes, the ratio of tb/ta serves as a good indicator of recovery abruptness and thus gives a comparative estimate of probable noise generated. A ratio of 1 is considered ideal and values less than 0.5 are considered snappy. Compared to Motorola standard cell density low voltage MOSFETs, high cell density MOSFET diodes are faster (shorter trr), have less stored charge and a softer reverse recovery characteristic. The softness advantage of the high cell density diode means they can be forced through reverse recovery at a higher di/dt than a standard cell MOSFET diode without increasing the current ringing or the noise generated. In addition, power dissipation incurred from switching the diode will be less due to the shorter recovery time and lower switching losses. I S , SOURCE CURRENT (AMPS) 15 VGS = 0 V TJ = 25°C 12 9 6 3 0 0.5 0.75 1 1.25 1.5 1.75 2 2.25 2.5 VSD, SOURCE–TO–DRAIN VOLTAGE (Volts) Figure 10. Diode Forward Voltage versus Current Motorola TMOS Power MOSFET Transistor Device Data 5 MTD20P06HDL di/dt = 300 A/µs Standard Cell Density trr I S , SOURCE CURRENT High Cell Density trr tb ta t, TIME Figure 11. Reverse Recovery Time (trr) SAFE OPERATING AREA The Forward Biased Safe Operating Area curves define the maximum simultaneous drain–to–source voltage and drain current that a transistor can handle safely when it is forward biased. Curves are based upon maximum peak junction temperature and a case temperature (TC) of 25°C. Peak repetitive pulsed power limits are determined by using the thermal response data in conjunction with the procedures discussed in AN569, “Transient Thermal Resistance – General Data and Its Use.” Switching between the off–state and the on–state may traverse any load line provided neither rated peak current (IDM) nor rated voltage (VDSS) is exceeded, and that the transition time (tr, tf) does not exceed 10 µs. In addition the total power averaged over a complete switching cycle must not exceed (TJ(MAX) – TC)/(RθJC). A power MOSFET designated E–FET can be safely used in switching circuits with unclamped inductive loads. For reli- able operation, the stored energy from circuit inductance dissipated in the transistor while in avalanche must be less than the rated limit and must be adjusted for operating conditions differing from those specified. Although industry practice is to rate in terms of energy, avalanche energy capability is not a constant. The energy rating decreases non–linearly with an increase of peak current in avalanche and peak junction temperature. Although many E–FETs can withstand the stress of drain– to–source avalanche at currents up to rated pulsed current (IDM), the energy rating is specified at rated continuous current (ID), in accordance with industry custom. The energy rating must be derated for temperature as shown in the accompanying graph (Figure 13). Maximum energy at currents below rated continuous ID can safely be assumed to equal the values indicated. 300 VGS = 20 V SINGLE PULSE TC = 25°C 1 ms 10 ms dc 1.0 0.1 0.1 6 100 µs 10 RDS(on) LIMIT THERMAL LIMIT PACKAGE LIMIT 1.0 10 100 EAS, SINGLE PULSE DRAIN–TO–SOURCE AVALANCHE ENERGY (mJ) I D , DRAIN CURRENT (AMPS) 100 ID = 15 A 240 180 120 60 0 25 50 75 100 125 150 VDS, DRAIN–TO–SOURCE VOLTAGE (VOLTS) TJ, STARTING JUNCTION TEMPERATURE (°C) Figure 12. Maximum Rated Forward Biased Safe Operating Area Figure 13. Maximum Avalanche Energy versus Starting Junction Temperature Motorola TMOS Power MOSFET Transistor Device Data MTD20P06HDL r(t), EFFECTIVE TRANSIENT THERMAL RESISTANCE (NORMALIZED) TYPICAL ELECTRICAL CHARACTERISTICS 1.0 D = 0.5 0.2 0.1 0.1 P(pk) 0.05 0.02 t1 0.01 t2 DUTY CYCLE, D = t1/t2 SINGLE PULSE 0.01 1.0E–05 1.0E–04 1.0E–03 1.0E–02 t, TIME (s) 1.0E–01 RθJC(t) = r(t) RθJC D CURVES APPLY FOR POWER PULSE TRAIN SHOWN READ TIME AT t1 TJ(pk) – TC = P(pk) RθJC(t) 1.0E+00 1.0E+01 Figure 14. Thermal Response di/dt IS trr ta tb TIME 0.25 IS tp IS Figure 15. Diode Reverse Recovery Waveform Motorola TMOS Power MOSFET Transistor Device Data 7 MTD20P06HDL INFORMATION FOR USING THE DPAK SURFACE MOUNT PACKAGE RECOMMENDED FOOTPRINT FOR SURFACE MOUNTED APPLICATIONS Surface mount board layout is a critical portion of the total design. The footprint for the semiconductor packages must be the correct size to ensure proper solder connection interface 0.165 4.191 between the board and the package. With the correct pad geometry, the packages will self align when subjected to a solder reflow process. 0.100 2.54 0.118 3.0 0.063 1.6 0.190 4.826 0.243 6.172 inches mm POWER DISSIPATION FOR A SURFACE MOUNT DEVICE PD = TJ(max) – TA RθJA The values for the equation are found in the maximum ratings table on the data sheet. Substituting these values into the equation for an ambient temperature TA of 25°C, one can calculate the power dissipation of the device. For a DPAK device, PD is calculated as follows. PD = 150°C – 25°C = 1.75 Watts 71.4°C/W The 71.4°C/W for the DPAK package assumes the use of the recommended footprint on a glass epoxy printed circuit board to achieve a power dissipation of 1.75 Watts. There are other alternatives to achieving higher power dissipation from the surface mount packages. One is to increase the area of the drain pad. By increasing the area of the drain pad, the power 8 dissipation can be increased. Although one can almost double the power dissipation with this method, one will be giving up area on the printed circuit board which can defeat the purpose of using surface mount technology. For example, a graph of RθJA versus drain pad area is shown in Figure 16. 100 RθJA , THERMAL RESISTANCE, JUNCTION TO AMBIENT (°C/W) The power dissipation for a surface mount device is a function of the drain pad size. These can vary from the minimum pad size for soldering to a pad size given for maximum power dissipation. Power dissipation for a surface mount device is determined by TJ(max), the maximum rated junction temperature of the die, RθJA, the thermal resistance from the device junction to ambient, and the operating temperature, TA. Using the values provided on the data sheet, PD can be calculated as follows: Board Material = 0.0625″ G–10/FR–4, 2 oz Copper 1.75 Watts 80 TA = 25°C 60 3.0 Watts 40 5.0 Watts 20 0 2 4 6 A, AREA (SQUARE INCHES) 8 10 Figure 16. Thermal Resistance versus Drain Pad Area for the DPAK Package (Typical) Another alternative would be to use a ceramic substrate or an aluminum core board such as Thermal Clad. Using a board material such as Thermal Clad, an aluminum core board, the power dissipation can be doubled using the same footprint. Motorola TMOS Power MOSFET Transistor Device Data ÇÇÇÇÇÇ ÇÇÇÇÇÇÇÇ ÇÇÇÇÇÇÇÇ ÇÇÇÇÇÇÇÇ ÇÇÇÇÇÇÇÇ ÇÇÇÇÇÇÇÇ ÇÇÇÇÇÇÇÇ SOLDER STENCIL GUIDELINES Prior to placing surface mount components onto a printed circuit board, solder paste must be applied to the pads. Solder stencils are used to screen the optimum amount. These stencils are typically 0.008 inches thick and may be made of brass or stainless steel. For packages such as the SC–59, SC–70/SOT–323, SOD–123, SOT–23, SOT–143, SOT–223, SO–8, SO–14, SO–16, and SMB/SMC diode packages, the stencil opening should be the same as the pad size or a 1:1 registration. This is not the case with the DPAK and D2PAK packages. If one uses a 1:1 opening to screen solder onto the drain pad, misalignment and/or “tombstoning” may occur due to an excess of solder. For these two packages, the opening in the stencil for the paste should be approximately 50% of the tab area. The opening for the leads is still a 1:1 registration. Figure 17 shows a typical stencil for the DPAK and D2PAK packages. The pattern of the opening in the stencil for the drain pad is not critical as long as it allows approximately 50% of the pad to be covered with paste. MTD20P06HDL ÇÇ ÇÇ ÇÇ ÇÇ SOLDER PASTE OPENINGS STENCIL Figure 17. Typical Stencil for DPAK and D2PAK Packages SOLDERING PRECAUTIONS The melting temperature of solder is higher than the rated temperature of the device. When the entire device is heated to a high temperature, failure to complete soldering within a short time could result in device failure. Therefore, the following items should always be observed in order to minimize the thermal stress to which the devices are subjected. • Always preheat the device. • The delta temperature between the preheat and soldering should be 100°C or less.* • When preheating and soldering, the temperature of the leads and the case must not exceed the maximum temperature ratings as shown on the data sheet. When using infrared heating with the reflow soldering method, the difference shall be a maximum of 10°C. • The soldering temperature and time shall not exceed 260°C for more than 10 seconds. Motorola TMOS Power MOSFET Transistor Device Data • When shifting from preheating to soldering, the maximum temperature gradient shall be 5°C or less. • After soldering has been completed, the device should be allowed to cool naturally for at least three minutes. Gradual cooling should be used as the use of forced cooling will increase the temperature gradient and result in latent failure due to mechanical stress. • Mechanical stress or shock should not be applied during cooling. * Soldering a device without preheating can cause excessive thermal shock and stress which can result in damage to the device. * Due to shadowing and the inability to set the wave height to incorporate other surface mount components, the D2PAK is not recommended for wave soldering. 9 MTD20P06HDL TYPICAL SOLDER HEATING PROFILE For any given circuit board, there will be a group of control settings that will give the desired heat pattern. The operator must set temperatures for several heating zones, and a figure for belt speed. Taken together, these control settings make up a heating “profile” for that particular circuit board. On machines controlled by a computer, the computer remembers these profiles from one operating session to the next. Figure 18 shows a typical heating profile for use when soldering a surface mount device to a printed circuit board. This profile will vary among soldering systems but it is a good starting point. Factors that can affect the profile include the type of soldering system in use, density and types of components on the board, type of solder used, and the type of board or substrate material being used. This profile shows temperature versus time. The STEP 1 PREHEAT ZONE 1 “RAMP” 200°C STEP 2 STEP 3 VENT HEATING “SOAK” ZONES 2 & 5 “RAMP” DESIRED CURVE FOR HIGH MASS ASSEMBLIES line on the graph shows the actual temperature that might be experienced on the surface of a test board at or near a central solder joint. The two profiles are based on a high density and a low density board. The Vitronics SMD310 convection/infrared reflow soldering system was used to generate this profile. The type of solder used was 62/36/2 Tin Lead Silver with a melting point between 177 –189°C. When this type of furnace is used for solder reflow work, the circuit boards and solder joints tend to heat first. The components on the board are then heated by conduction. The circuit board, because it has a large surface area, absorbs the thermal energy more efficiently, then distributes this energy to the components. Because of this effect, the main body of a component may be up to 30 degrees cooler than the adjacent solder joints. STEP 5 STEP 4 HEATING HEATING ZONES 3 & 6 ZONES 4 & 7 “SPIKE” “SOAK” 170°C STEP 6 VENT STEP 7 COOLING 205° TO 219°C PEAK AT SOLDER JOINT 160°C 150°C 150°C 100°C 140°C 100°C SOLDER IS LIQUID FOR 40 TO 80 SECONDS (DEPENDING ON MASS OF ASSEMBLY) DESIRED CURVE FOR LOW MASS ASSEMBLIES 50°C TIME (3 TO 7 MINUTES TOTAL) TMAX Figure 18. Typical Solder Heating Profile 10 Motorola TMOS Power MOSFET Transistor Device Data MTD20P06HDL PACKAGE DIMENSIONS –T– C B V NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. SEATING PLANE E R Z A S U K F J L H D G STYLE 2: PIN 1. 2. 3. 4. 2 PL 0.13 (0.005) M T GATE DRAIN SOURCE DRAIN DIM A B C D E F G H J K L R S U V Z INCHES MIN MAX 0.235 0.250 0.250 0.265 0.086 0.094 0.027 0.035 0.033 0.040 0.037 0.047 0.180 BSC 0.034 0.040 0.018 0.023 0.102 0.114 0.090 BSC 0.175 0.215 0.020 0.050 0.020 ––– 0.030 0.050 0.138 ––– MILLIMETERS MIN MAX 5.97 6.35 6.35 6.73 2.19 2.38 0.69 0.88 0.84 1.01 0.94 1.19 4.58 BSC 0.87 1.01 0.46 0.58 2.60 2.89 2.29 BSC 4.45 5.46 0.51 1.27 0.51 ––– 0.77 1.27 3.51 ––– CASE 369A–13 ISSUE W Motorola TMOS Power MOSFET Transistor Device Data 11 MTD20P06HDL Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters can and do vary in different applications. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. How to reach us: USA / EUROPE: Motorola Literature Distribution; P.O. Box 20912; Phoenix, Arizona 85036. 1–800–441–2447 JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, Toshikatsu Otsuki, 6F Seibu–Butsuryu–Center, 3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 03–3521–8315 MFAX: [email protected] – TOUCHTONE (602) 244–6609 INTERNET: http://Design–NET.com HONG KONG: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298 12 ◊ *MTD20P06HDL/D* Motorola TMOS Power MOSFET Transistor Device Data MTD20P06HDL/D