74AUP1G126 Low-power buffer/line driver; 3-state Rev. 01 — 25 July 2005 Product data sheet 1. General description The 74AUP1G126 is a high-performance, low-power, low-voltage, Si-gate CMOS device, superior to most advanced CMOS compatible TTL families. Schmitt-trigger action at all inputs makes the circuit tolerant to slower input rise and fall times across the entire VCC range from 0.8 V to 3.6 V. This device ensures a very low static and dynamic power consumption across the entire VCC range from 0.8 V to 3.6 V. This device is fully specified for partial Power-down applications using IOFF. The IOFF circuitry disables the output, preventing the damaging backflow current through the device when it is powered down. The 74AUP1G126 provides the single non-inverting buffer/line driver with 3-state output. The 3-state output is controlled by the output enable input (OE). A LOW level at pin OE causes the output to assume a high-impedance OFF-state. This device has the input-disable feature, which allows floating input signals. The inputs are disabled when the output enable input OE is LOW. 2. Features ■ Wide supply voltage range from 0.8 V to 3.6 V ■ High noise immunity ■ Complies with JEDEC standards: ◆ JESD8-12 (0.8 V to 1.3 V) ◆ JESD8-11 (0.9 V to 1.65 V) ◆ JESD8-7 (1.2 V to 1.95 V) ◆ JESD8-5 (1.8 V to 2.7 V) ◆ JESD8-B (2.7 V to 3.6 V) ■ ESD protection: ◆ HBM JESD22-A114-C exceeds 2000 V ◆ MM JESD22-A115-A exceeds 200 V ◆ CDM JESD22-C101-C exceeds 1000 V ■ Low static power consumption; ICC = 0.9 µA (maximum) ■ Latch-up performance exceeds 100 mA per JESD 78 Class II ■ Inputs accept voltages up to 3.6 V ■ Low noise overshoot and undershoot < 10 % of VCC ■ Input-disable feature allows floating input conditions 74AUP1G126 Philips Semiconductors Low-power buffer/line driver; 3-state ■ IOFF circuitry provides partial Power-down mode operation ■ Multiple package options ■ Specified from −40 °C to +85 °C and −40 °C to +125 °C 3. Quick reference data Table 1: Quick reference data GND = 0 V; Tamb = 25 °C; tr = tf ≤ 3 ns. Symbol Parameter Conditions Min Typ Max Unit - 20.6 - ns CL = 5 pF; RL = 1 MΩ; VCC = 1.1 V to 1.3 V 2.8 5.5 11.8 ns CL = 5 pF; RL = 1 MΩ; VCC = 1.4 V to 1.6 V 2.2 3.9 7.0 ns CL = 5 pF; RL = 1 MΩ; VCC = 1.65 V to 1.95 V 1.9 3.2 5.5 ns CL = 5 pF; RL = 1 MΩ; VCC = 2.3 V to 2.7 V 1.7 2.6 4.2 ns CL = 5 pF; RL = 1 MΩ; VCC = 3.0 V to 3.6 V 1.7 2.4 3.7 ns - 0.9 - pF VCC = 1.8 V - 3.6 - pF VCC = 3.3 V - 4.4 - pF - 0 - pF tPHL, tPLH propagation delay CL = 5 pF; RL = 1 MΩ; A to Y VCC = 0.8 V input capacitance Ci power dissipation capacitance CPD f = 10 MHz; output enabled f = 10 MHz; output disabled [1] [2] [1] [2] VCC = 0.8 V to 3.6 V [1] CPD is used to determine the dynamic power dissipation (PD in µW). PD = CPD × VCC2 × fi × N + Σ(CL × VCC2 × fo) where: fi = input frequency in MHz; fo = output frequency in MHz; CL = output load capacitance in pF; VCC = supply voltage in V; N = number of inputs switching; Σ(CL × VCC2 × fo) = sum of the outputs. [2] The condition is VI = GND to VCC. 4. Ordering information Table 2: Ordering information Type number Package Temperature range Name Description Version 74AUP1G126GW −40 °C to +125 °C TSSOP5 plastic thin shrink small outline package; 5 leads; body width 1.25 mm SOT353-1 74AUP1G126GM −40 °C to +125 °C XSON6 plastic extremely thin small outline package; no leads; SOT886 6 terminals; body 1 × 1.45 × 0.5 mm 9397 750 14686 Product data sheet © Koninklijke Philips Electronics N.V. 2005. All rights reserved. Rev. 01 — 25 July 2005 2 of 20 74AUP1G126 Philips Semiconductors Low-power buffer/line driver; 3-state 5. Marking Table 3: Marking Type number Marking code 74AUP1G126GW pN 74AUP1G126GM pN 6. Functional diagram 2 A 1 OE Y 4 2 4 1 OE mna126 mna125 Fig 1. Logic symbol Fig 2. IEC logic symbol A Y OE 001aad069 Fig 3. Logic diagram 7. Pinning information 7.1 Pinning 126 OE A GND 1 2 5 VCC 1 6 VCC A 2 5 n.c. GND 3 4 Y 126 3 4 Y 001aab653 Fig 4. Pin configuration SOT353-1 (TSSOP5) 9397 750 14686 Product data sheet OE 001aab654 Transparent top view Fig 5. Pin configuration SOT886 (XSON6) © Koninklijke Philips Electronics N.V. 2005. All rights reserved. Rev. 01 — 25 July 2005 3 of 20 74AUP1G126 Philips Semiconductors Low-power buffer/line driver; 3-state 7.2 Pin description Table 4: Pin description Symbol Pin Description TSSOP5 XSON6 OE 1 1 output enable input A 2 2 data input A GND 3 3 ground (0 V) Y 4 4 data output Y n.c. - 5 not connected VCC 5 6 supply voltage 8. Functional description 8.1 Function table Table 5: Function table [1] Input Output OE A Y H L L H H H L X Z [1] H = HIGH voltage level; L = LOW voltage level; X = Don’t care; Z = high-impedance OFF-state. 9. Limiting values Table 6: Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to GND (ground = 0 V). Symbol Parameter Conditions VCC supply voltage IIK input clamping current VI input voltage IOK output clamping current VO > VCC or VO < 0 V VO output voltage active mode Power-down mode Max Unit −0.5 +4.6 V - −50 mA −0.5 +4.6 V - ±50 mA [1] −0.5 VCC + 0.5 V [1] −0.5 +4.6 V - ±20 mA - +50 mA VI < 0 V [1] IO output current VO = 0 V to VCC ICC quiescent supply current 9397 750 14686 Product data sheet Min © Koninklijke Philips Electronics N.V. 2005. All rights reserved. Rev. 01 — 25 July 2005 4 of 20 74AUP1G126 Philips Semiconductors Low-power buffer/line driver; 3-state Table 6: Limiting values …continued In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to GND (ground = 0 V). Symbol Parameter Conditions IGND ground current Tstg storage temperature Ptot total power dissipation Tamb = −40 °C to +125 °C [2] Min Max Unit - −50 mA −65 +150 °C - 250 mW [1] The input and output voltage ratings may be exceeded if the input and output current ratings are observed. [2] For TSSOP5 packages: above 87.5 °C the value of Ptot derates linearly with 4.0 mW/K. For XSON6 packages: above 45 °C the value of Ptot derates linearly with 2.4 mW/K. 10. Recommended operating conditions Table 7: Recommended operating conditions Symbol Parameter Min Max Unit VCC supply voltage Conditions 0.8 3.6 V VI input voltage 0 3.6 V VO output voltage active mode 0 VCC V Power-down mode; VCC = 0 V 0 3.6 V Tamb ambient temperature −40 +125 °C tr, tf input rise and fall times 0 200 ns/V VCC = 0.8 V to 3.6 V 11. Static characteristics Table 8: Static characteristics At recommended operating conditions; voltages are referenced to GND (ground = 0 V). Symbol Parameter Conditions Min VCC = 0.8 V Typ Max Unit 0.70 × VCC - - V VCC = 0.9 V to 1.95 V 0.65 × VCC - - V Tamb = 25 °C VIH VIL HIGH-state input voltage LOW-state input voltage VCC = 2.3 V to 2.7 V 1.6 - - V VCC = 3.0 V to 3.6 V 2.0 - - V VCC = 0.8 V - - 0.30 × VCC V VCC = 0.9 V to 1.95 V - - 0.35 × VCC V VCC = 2.3 V to 2.7 V - - 0.7 V VCC = 3.0 V to 3.6 V - - 0.9 V 9397 750 14686 Product data sheet © Koninklijke Philips Electronics N.V. 2005. All rights reserved. Rev. 01 — 25 July 2005 5 of 20 74AUP1G126 Philips Semiconductors Low-power buffer/line driver; 3-state Table 8: Static characteristics …continued At recommended operating conditions; voltages are referenced to GND (ground = 0 V). Symbol Parameter Conditions VOH VI = VIH or VIL VOL HIGH-state output voltage LOW-state output voltage Min Typ Max Unit IO = −20 µA; VCC = 0.8 V to 3.6 V VCC − 0.1 - - V IO = −1.1 mA; VCC = 1.1 V 0.75 × VCC - - V IO = −1.7 mA; VCC = 1.4 V 1.11 - - V IO = −1.9 mA; VCC = 1.65 V 1.32 - - V IO = −2.3 mA; VCC = 2.3 V 2.05 - - V IO = −3.1 mA; VCC = 2.3 V 1.9 - - V IO = −2.7 mA; VCC = 3.0 V 2.72 - - V IO = −4.0 mA; VCC = 3.0 V 2.6 - - V VI = VIH or VIL IO = 20 µA; VCC = 0.8 V to 3.6 V - - 0.1 V IO = 1.1 mA; VCC = 1.1 V - - 0.3 × VCC V IO = 1.7 mA; VCC = 1.4 V - - 0.31 V IO = 1.9 mA; VCC = 1.65 V - - 0.31 V IO = 2.3 mA; VCC = 2.3 V - - 0.31 V IO = 3.1 mA; VCC = 2.3 V - - 0.44 V IO = 2.7 mA; VCC = 3.0 V - - 0.31 V IO = 4.0 mA; VCC = 3.0 V - - 0.44 V ILI input leakage current VI = GND to 3.6 V; VCC = 0 V to 3.6 V - - ±0.1 µA IOZ 3-state output OFF-state current VI = VIH or VIL; VO = 0 V to 3.6 V; VCC = 0 V to 3.6 V - - ±0.1 µA IOFF power-off leakage current VI or VO = 0 V to 3.6 V; VCC = 0 V - - ±0.2 µA ∆IOFF additional power-off leakage current VI or VO = 0 V to 3.6 V; VCC = 0 V to 0.2 V - - ±0.2 µA ICC quiescent supply current VI = GND or VCC; IO = 0 A; VCC = 0.8 V to 3.6 V - - 0.5 µA ∆ICC additional quiescent supply data input; VI = VCC − 0.6 V; IO = 0 A; current VCC = 3.3 V [1] - - 40 µA OE input; VI = VCC − 0.6 V; IO = 0 A; VCC = 3.3 V [1] - - 110 µA all inputs; VI = GND to 3.6 V; OE = GND; VCC = 0.8 V to 3.6 V [2] - - 1 µA Ci input capacitance VCC = 0 V to 3.6 V; VI = GND or VCC - 0.9 - pF Co output capacitance output enabled; VO = GND; VCC = 0 V - 1.7 - pF output disabled; VCC = 0 V to 3.6 V; VO = GND or VCC - 1.5 - pF VCC = 0.8 V 0.70 × VCC - - V VCC = 0.9 V to 1.95 V 0.65 × VCC - - V VCC = 2.3 V to 2.7 V 1.6 - - V VCC = 3.0 V to 3.6 V 2.0 - - V Tamb = −40 °C to +85 °C VIH HIGH-state input voltage 9397 750 14686 Product data sheet © Koninklijke Philips Electronics N.V. 2005. All rights reserved. Rev. 01 — 25 July 2005 6 of 20 74AUP1G126 Philips Semiconductors Low-power buffer/line driver; 3-state Table 8: Static characteristics …continued At recommended operating conditions; voltages are referenced to GND (ground = 0 V). Symbol Parameter Conditions Min Typ Max VIL VCC = 0.8 V - - 0.30 × VCC V VCC = 0.9 V to 1.95 V - - 0.35 × VCC V VCC = 2.3 V to 2.7 V - - 0.7 V VCC = 3.0 V to 3.6 V - - 0.9 V IO = −20 µA; VCC = 0.8 V to 3.6 V VCC − 0.1 - - V VOH VOL LOW-state input voltage HIGH-state output voltage LOW-state output voltage Unit VI = VIH or VIL IO = −1.1 mA; VCC = 1.1 V 0.7 × VCC - - V IO = −1.7 mA; VCC = 1.4 V 1.03 - - V IO = −1.9 mA; VCC = 1.65 V 1.30 - - V IO = −2.3 mA; VCC = 2.3 V 1.97 - - V IO = −3.1 mA; VCC = 2.3 V 1.85 - - V IO = −2.7 mA; VCC = 3.0 V 2.67 - - V IO = −4.0 mA; VCC = 3.0 V 2.55 - - V VI = VIH or VIL IO = 20 µA; VCC = 0.8 V to 3.6 V - - 0.1 V IO = 1.1 mA; VCC = 1.1 V - - 0.3 × VCC V IO = 1.7 mA; VCC = 1.4 V - - 0.37 V IO = 1.9 mA; VCC = 1.65 V - - 0.35 V IO = 2.3 mA; VCC = 2.3 V - - 0.33 V IO = 3.1 mA; VCC = 2.3 V - - 0.45 V IO = 2.7 mA; VCC = 3.0 V - - 0.33 V IO = 4.0 mA; VCC = 3.0 V - - 0.45 V ILI input leakage current VI = GND to 3.6 V; VCC = 0 V to 3.6 V - - ±0.5 µA IOZ 3-state output OFF-state current VI = VIH or VIL; VO = 0 V to 3.6 V; VCC = 0 V to 3.6 V - - ±0.5 µA IOFF power-off leakage current VI or VO = 0 V to 3.6 V; VCC = 0 V - - ±0.5 µA ∆IOFF additional power-off leakage current VI or VO = 0 V to 3.6 V; VCC = 0 V to 0.2 V - - ±0.6 µA ICC quiescent supply current VI = GND or VCC; IO = 0 A; VCC = 0.8 V to 3.6 V - - 0.9 µA ∆ICC additional quiescent supply data input; VI = VCC − 0.6 V; IO = 0 A; current VCC = 3.3 V [1] - - 50 µA OE input; VI = VCC − 0.6 V; IO = 0 A; VCC = 3.3 V [1] - - 120 µA all inputs; VI = GND to 3.6 V; OE = GND; VCC = 0.8 V to 3.6 V [2] - - 1 µA VCC = 0.8 V 0.75 × VCC - - V VCC = 0.9 V to 1.95 V 0.70 × VCC - - V VCC = 2.3 V to 2.7 V 1.6 - - V VCC = 3.0 V to 3.6 V 2.0 - - V Tamb = −40 °C to +125 °C VIH HIGH-state input voltage 9397 750 14686 Product data sheet © Koninklijke Philips Electronics N.V. 2005. All rights reserved. Rev. 01 — 25 July 2005 7 of 20 74AUP1G126 Philips Semiconductors Low-power buffer/line driver; 3-state Table 8: Static characteristics …continued At recommended operating conditions; voltages are referenced to GND (ground = 0 V). Symbol Parameter Conditions Min Typ Max VIL VCC = 0.8 V - - 0.25 × VCC V VCC = 0.9 V to 1.95 V - - 0.30 × VCC V VCC = 2.3 V to 2.7 V - - 0.7 V VCC = 3.0 V to 3.6 V - - 0.9 V LOW-state input voltage VOH HIGH-state output voltage LOW-state output voltage VOL Unit VI = VIH or VIL IO = −20 µA; VCC = 0.8 V to 3.6 V VCC − 0.11 - - V IO = −1.1 mA; VCC = 1.1 V 0.6 × VCC - - V IO = −1.7 mA; VCC = 1.4 V 0.93 - - V IO = −1.9 mA; VCC = 1.65 V 1.17 - - V IO = −2.3 mA; VCC = 2.3 V 1.77 - - V IO = −3.1 mA; VCC = 2.3 V 1.67 - - V IO = −2.7 mA; VCC = 3.0 V 2.40 - - V IO = −4.0 mA; VCC = 3.0 V 2.30 - - V V VI = VIH or VIL IO = 20 µA; VCC = 0.8 V to 3.6 V - - 0.11 IO = 1.1 mA; VCC = 1.1 V - - 0.33 × VCC V IO = 1.7 mA; VCC = 1.4 V - - 0.41 V IO = 1.9 mA; VCC = 1.65 V - - 0.39 V IO = 2.3 mA; VCC = 2.3 V - - 0.36 V IO = 3.1 mA; VCC = 2.3 V - - 0.50 V IO = 2.7 mA; VCC = 3.0 V - - 0.36 V IO = 4.0 mA; VCC = 3.0 V - - 0.50 V ILI input leakage current VI = GND to 3.6 V; VCC = 0 V to 3.6 V - - ±0.75 µA IOZ 3-state output OFF-state current VI = VIH or VIL; VO = 0 V to 3.6 V; VCC = 0 V to 3.6 V - - ±0.75 µA IOFF power-off leakage current VI or VO = 0 V to 3.6 V; VCC = 0 V - - ±0.75 µA ∆IOFF additional power-off leakage current VI or VO = 0 V to 3.6 V; VCC = 0 V to 0.2 V - - ±0.75 µA ICC quiescent supply current VI = GND or VCC; IO = 0 A; VCC = 0.8 V to 3.6 V - - 1.4 µA ∆ICC additional quiescent supply data input; VI = VCC − 0.6 V; IO = 0 A; current VCC = 3.3 V [1] - - 75 µA OE input; VI = VCC − 0.6 V; IO = 0 A; VCC = 3.3 V [1] - - 180 µA all inputs; VI = GND to 3.6 V; OE = GND; VCC = 0.8 V to 3.6 V [2] - - 1 µA [1] One input at VCC − 0.6 V, other input at VCC or GND. [2] To show ICC remains very low when the input-disable feature is enabled. 9397 750 14686 Product data sheet © Koninklijke Philips Electronics N.V. 2005. All rights reserved. Rev. 01 — 25 July 2005 8 of 20 74AUP1G126 Philips Semiconductors Low-power buffer/line driver; 3-state 12. Dynamic characteristics Table 9: Dynamic characteristics Voltages are referenced to GND (ground = 0 V); for test circuit see Figure 8 Symbol Parameter Conditions Min Typ VCC = 0.8 V - VCC = 1.1 V to 1.3 V VCC = 1.4 V to 1.6 V [1] Max Unit 20.6 - ns 2.8 5.5 11.8 ns 2.2 3.9 7.0 ns Tamb = 25 °C; CL = 5 pF tPHL, tPLH tPZH, tPZL tPHZ, tPLZ propagation delay A to Y 3-state output enable time OE to Y 3-state output disable time OE to Y see Figure 6 VCC = 1.65 V to 1.95 V 1.9 3.2 5.5 ns VCC = 2.3 V to 2.7 V 1.7 2.6 4.2 ns VCC = 3.0 V to 3.6 V 1.7 2.4 3.7 ns see Figure 7 VCC = 0.8 V - 71.6 - ns VCC = 1.1 V to 1.3 V 3.1 6.2 13.7 ns VCC = 1.4 V to 1.6 V 2.3 4.2 7.7 ns VCC = 1.65 V to 1.95 V 1.9 3.3 5.9 ns VCC = 2.3 V to 2.7 V 1.5 2.4 4.1 ns VCC = 3.0 V to 3.6 V 1.3 2.0 3.4 ns VCC = 0.8 V - 10.3 - ns VCC = 1.1 V to 1.3 V 2.6 4.2 7.0 ns VCC = 1.4 V to 1.6 V 2.1 3.2 5.0 ns VCC = 1.65 V to 1.95 V 2.1 3.1 4.7 ns VCC = 2.3 V to 2.7 V 1.7 2.4 3.6 ns VCC = 3.0 V to 3.6 V 2.1 2.8 4.2 ns VCC = 0.8 V - 24.0 - ns VCC = 1.1 V to 1.3 V 3.2 6.4 13.7 ns VCC = 1.4 V to 1.6 V 2.1 4.5 8.1 ns VCC = 1.65 V to 1.95 V 1.9 3.8 6.3 ns VCC = 2.3 V to 2.7 V 2.2 3.2 4.9 ns VCC = 3.0 V to 3.6 V 2.1 3.0 4.5 ns VCC = 0.8 V - 75.3 - ns VCC = 1.1 V to 1.3 V 3.5 7.1 15.5 ns VCC = 1.4 V to 1.6 V 2.2 4.8 8.7 ns VCC = 1.65 V to 1.95 V 1.8 3.9 6.7 ns VCC = 2.3 V to 2.7 V 1.5 2.9 4.8 ns VCC = 3.0 V to 3.6 V 1.4 2.6 4.1 ns see Figure 7 Tamb = 25 °C; CL = 10 pF tPHL, tPLH tPZH, tPZL propagation delay A to Y 3-state output enable time OE to Y see Figure 6 see Figure 7 9397 750 14686 Product data sheet © Koninklijke Philips Electronics N.V. 2005. All rights reserved. Rev. 01 — 25 July 2005 9 of 20 74AUP1G126 Philips Semiconductors Low-power buffer/line driver; 3-state Table 9: Dynamic characteristics …continued Voltages are referenced to GND (ground = 0 V); for test circuit see Figure 8 Symbol Parameter Conditions Min Typ tPHZ, tPLZ 3-state output disable time OE to Y see Figure 7 VCC = 0.8 V - VCC = 1.1 V to 1.3 V VCC = 1.4 V to 1.6 V [1] Max Unit 12.2 - ns 3.5 5.3 8.5 ns 2.2 4.1 6.1 ns VCC = 1.65 V to 1.95 V 2.4 4.2 6.2 ns VCC = 2.3 V to 2.7 V 1.9 3.2 4.7 ns VCC = 3.0 V to 3.6 V 2.4 4.1 5.9 ns VCC = 0.8 V - 27.4 - ns VCC = 1.1 V to 1.3 V 3.6 7.2 15.5 ns VCC = 1.4 V to 1.6 V 3.0 5.1 9.1 ns VCC = 1.65 V to 1.95 V 2.2 4.3 7.1 ns VCC = 2.3 V to 2.7 V 2.0 3.7 5.6 ns VCC = 3.0 V to 3.6 V 2.0 3.5 5.2 ns VCC = 0.8 V - 79.2 - ns VCC = 1.1 V to 1.3 V 4.0 7.8 17.2 ns VCC = 1.4 V to 1.6 V 3.0 5.4 9.7 ns VCC = 1.65 V to 1.95 V 2.1 4.3 7.4 ns VCC = 2.3 V to 2.7 V 1.8 3.4 5.4 ns VCC = 3.0 V to 3.6 V 1.6 3.1 4.7 ns VCC = 0.8 V - 14.9 - ns VCC = 1.1 V to 1.3 V 4.3 6.4 10.0 ns VCC = 1.4 V to 1.6 V 3.0 5.0 7.2 ns Tamb = 25 °C; CL = 15 pF tPHL, tPLH tPZH, tPZL tPHZ, tPLZ propagation delay A to Y 3-state output enable time OE to Y 3-state output disable time OE to Y see Figure 6 see Figure 7 see Figure 7 VCC = 1.65 V to 1.95 V 3.1 5.4 7.7 ns VCC = 2.3 V to 2.7 V 2.4 4.0 5.8 ns VCC = 3.0 V to 3.6 V 3.2 5.3 7.7 ns VCC = 0.8 V - 37.6 - ns VCC = 1.1 V to 1.3 V 4.8 9.6 20.8 ns VCC = 1.4 V to 1.6 V 4.0 6.7 12.0 ns Tamb = 25 °C; CL = 30 pF tPHL, tPLH propagation delay A to Y see Figure 6 VCC = 1.65 V to 1.95 V 2.9 5.6 9.4 ns VCC = 2.3 V to 2.7 V 2.7 4.8 7.3 ns VCC = 3.0 V to 3.6 V 2.7 4.6 6.4 ns 9397 750 14686 Product data sheet © Koninklijke Philips Electronics N.V. 2005. All rights reserved. Rev. 01 — 25 July 2005 10 of 20 74AUP1G126 Philips Semiconductors Low-power buffer/line driver; 3-state Table 9: Dynamic characteristics …continued Voltages are referenced to GND (ground = 0 V); for test circuit see Figure 8 Symbol Parameter Conditions tPZH, tPZL 3-state output enable time OE to Y see Figure 7 tPHZ, tPLZ 3-state output disable time OE to Y [1] Min Typ Max Unit VCC = 0.8 V - 90.6 - ns VCC = 1.1 V to 1.3 V 5.1 10.0 22.1 ns VCC = 1.4 V to 1.6 V 4.0 6.9 12.3 ns VCC = 1.65 V to 1.95 V 2.8 5.6 9.4 ns VCC = 2.3 V to 2.7 V 2.4 4.5 7.0 ns VCC = 3.0 V to 3.6 V 2.4 4.2 6.4 ns VCC = 0.8 V - 51.6 - ns VCC = 1.1 V to 1.3 V 6.0 9.8 14.9 ns VCC = 1.4 V to 1.6 V 4.5 7.7 10.7 ns VCC = 1.65 V to 1.95 V 5.2 8.8 12.2 ns VCC = 2.3 V to 2.7 V 3.9 6.4 9.1 ns VCC = 3.0 V to 3.6 V 5.5 9.0 12.9 ns VCC = 0.8 V - 3.2 - pF VCC = 1.1 V to 1.3 V - 3.4 - pF VCC = 1.4 V to 1.6 V - 3.5 - pF VCC = 1.65 V to 1.95 V - 3.6 - pF VCC = 2.3 V to 2.7 V - 4.0 - pF VCC = 3.0 V to 3.6 V - 4.4 - pF - 0 - pF see Figure 7 Tamb = 25 °C power dissipation capacitance f = 10 MHz CPD [2] [3] output enabled output disabled VCC = 3.0 V to 3.6 V [1] All typical values are measured at nominal VCC. [2] CPD is used to determine the dynamic power dissipation (PD in µW). PD = CPD × VCC2 × fi × N + Σ(CL × VCC2 × fo) where: fi = input frequency in MHz; fo = output frequency in MHz; CL = output load capacitance in pF; VCC = supply voltage in V; N = number of inputs switching; Σ(CL × VCC2 × fo) = sum of the outputs. [3] The condition is VI = GND to VCC. 9397 750 14686 Product data sheet © Koninklijke Philips Electronics N.V. 2005. All rights reserved. Rev. 01 — 25 July 2005 11 of 20 74AUP1G126 Philips Semiconductors Low-power buffer/line driver; 3-state Table 10: Dynamic characteristics Voltages are referenced to GND (ground = 0 V); for test circuit see Figure 8 Symbol Parameter −40 °C to +85 °C Conditions −40 °C to +125 °C Unit Min Max Min Max VCC = 1.1 V to 1.3 V 2.6 13.2 2.6 14.5 ns VCC = 1.4 V to 1.6 V 2.0 8.2 2.0 9.0 ns VCC = 1.65 V to 1.95 V 1.7 6.5 1.7 7.2 ns VCC = 2.3 V to 2.7 V 1.5 5.0 1.5 5.5 ns VCC = 3.0 V to 3.6 V 1.5 4.4 1.5 4.9 ns VCC = 1.1 V to 1.3 V 2.9 16.2 2.9 17.9 ns VCC = 1.4 V to 1.6 V 2.2 8.9 2.2 9.8 ns VCC = 1.65 V to 1.95 V 1.7 6.8 1.7 7.5 ns VCC = 2.3 V to 2.7 V 1.4 4.8 1.4 5.3 ns VCC = 3.0 V to 3.6 V 1.2 4.0 1.2 4.4 ns VCC = 1.1 V to 1.3 V 2.9 7.7 2.9 8.5 ns VCC = 1.4 V to 1.6 V 2.2 5.6 2.2 6.2 ns VCC = 1.65 V to 1.95 V 1.7 5.4 1.7 6.0 ns VCC = 2.3 V to 2.7 V 1.4 4.2 1.4 4.7 ns VCC = 3.0 V to 3.6 V 1.2 4.7 1.2 5.2 ns VCC = 1.1 V to 1.3 V 3.0 15.4 3.0 17.0 ns VCC = 1.4 V to 1.6 V 1.9 9.5 1.9 10.5 ns CL = 5 pF tPHL, tPLH tPZH, tPZL tPHZ, tPLZ propagation delay A to Y 3-state output enable time OE to Y 3-state output disable time OE to Y see Figure 6 see Figure 7 see Figure 7 CL = 10 pF tPHL, tPLH tPZH, tPZL tPHZ, tPLZ propagation delay A to Y 3-state output enable time OE to Y 3-state output disable time OE to Y see Figure 6 VCC = 1.65 V to 1.95 V 1.7 7.6 1.7 8.4 ns VCC = 2.3 V to 2.7 V 1.6 5.9 1.6 6.5 ns VCC = 3.0 V to 3.6 V 1.6 5.3 1.6 5.9 ns see Figure 7 VCC = 1.1 V to 1.3 V 3.3 18.1 3.3 20.0 ns VCC = 1.4 V to 1.6 V 2.1 10.0 2.1 11.0 ns VCC = 1.65 V to 1.95 V 1.7 7.8 1.7 8.6 ns VCC = 2.3 V to 2.7 V 1.4 5.6 1.4 6.2 ns VCC = 3.0 V to 3.6 V 1.3 4.9 1.3 5.4 ns VCC = 1.1 V to 1.3 V 3.3 9.4 3.3 10.4 ns VCC = 1.4 V to 1.6 V 2.1 6.9 2.1 7.6 ns see Figure 7 VCC = 1.65 V to 1.95 V 1.7 7.0 1.7 7.7 ns VCC = 2.3 V to 2.7 V 1.4 5.3 1.4 5.9 ns VCC = 3.0 V to 3.6 V 1.3 6.6 1.3 7.3 ns 9397 750 14686 Product data sheet © Koninklijke Philips Electronics N.V. 2005. All rights reserved. Rev. 01 — 25 July 2005 12 of 20 74AUP1G126 Philips Semiconductors Low-power buffer/line driver; 3-state Table 10: Dynamic characteristics …continued Voltages are referenced to GND (ground = 0 V); for test circuit see Figure 8 Symbol Parameter −40 °C to +85 °C Conditions −40 °C to +125 °C Unit Min Max Min Max VCC = 1.1 V to 1.3 V 3.4 17.5 3.4 19.3 ns VCC = 1.4 V to 1.6 V 2.5 10.8 2.5 11.9 ns VCC = 1.65 V to 1.95 V 2.0 8.6 2.0 9.5 ns VCC = 2.3 V to 2.7 V 1.8 6.7 1.8 7.4 ns VCC = 3.0 V to 3.6 V 1.8 6.1 1.8 6.8 ns VCC = 1.1 V to 1.3 V 3.7 19.9 3.7 21.9 ns VCC = 1.4 V to 1.6 V 2.5 11.1 2.5 12.3 ns VCC = 1.65 V to 1.95 V 2.0 8.6 2.0 9.5 ns VCC = 2.3 V to 2.7 V 1.7 6.3 1.7 7.0 ns VCC = 3.0 V to 3.6 V 1.5 5.6 1.5 6.2 ns VCC = 1.1 V to 1.3 V 3.7 11.0 3.7 12.1 ns VCC = 1.4 V to 1.6 V 2.5 8.1 2.5 9.0 ns VCC = 1.65 V to 1.95 V 2.0 8.6 2.0 9.5 ns VCC = 2.3 V to 2.7 V 1.7 6.5 1.7 7.2 ns VCC = 3.0 V to 3.6 V 1.5 8.5 1.5 9.4 ns CL = 15 pF tPHL, tPLH tPZH, tPZL tPHZ, tPLZ propagation delay A to Y 3-state output enable time OE to Y 3-state output disable time OE to Y see Figure 6 see Figure 7 see Figure 7 CL = 30 pF tPHL, tPLH tPZH, tPZL tPHZ, tPLZ propagation delay A to Y 3-state output enable time OE to Y 3-state output disable time OE to Y see Figure 6 VCC = 1.1 V to 1.3 V 4.4 23.5 4.4 25.9 ns VCC = 1.4 V to 1.6 V 3.0 14.2 3.0 15.7 ns VCC = 1.65 V to 1.95 V 2.6 11.3 2.6 12.5 ns VCC = 2.3 V to 2.7 V 2.5 8.8 2.5 9.7 ns VCC = 3.0 V to 3.6 V 2.5 8.1 2.5 9.0 ns VCC = 1.1 V to 1.3 V 4.7 25.2 4.7 27.8 ns VCC = 1.4 V to 1.6 V 3.0 14.1 3.0 15.6 ns VCC = 1.65 V to 1.95 V 2.6 11.0 2.6 12.1 ns VCC = 2.3 V to 2.7 V 2.3 8.4 2.3 9.3 ns VCC = 3.0 V to 3.6 V 2.2 7.6 2.2 8.4 ns see Figure 7 see Figure 7 VCC = 1.1 V to 1.3 V 4.7 16.5 4.7 18.2 ns VCC = 1.4 V to 1.6 V 3.0 11.9 3.0 13.1 ns VCC = 1.65 V to 1.95 V 2.6 13.5 2.6 14.9 ns VCC = 2.3 V to 2.7 V 2.3 10.0 2.3 11.0 ns VCC = 3.0 V to 3.6 V 2.2 14.1 2.2 15.6 ns 9397 750 14686 Product data sheet © Koninklijke Philips Electronics N.V. 2005. All rights reserved. Rev. 01 — 25 July 2005 13 of 20 74AUP1G126 Philips Semiconductors Low-power buffer/line driver; 3-state 13. Waveforms VI VM A input GND t PLH t PHL Y output VM 001aad070 Measurement points are given in Table 11. Logic levels: VOL and VOH are typical output voltage drop that occur with the output load. Fig 6. The data input (A) to output (Y) propagation delays Table 11: Measurement points Supply voltage Output Input VCC VM VM VI tr = tf 0.8 V to 3.6 V 0.5 × VCC 0.5 × VCC VCC ≤ 3.0 ns VI VM OE input GND tPLZ tPZL VCC output LOW-to-OFF OFF-to-LOW VM VX VOL tPHZ VOH tPZH VY output HIGH-to-OFF OFF-to-HIGH VM GND output enabled output disabled output enabled mna646 Measurement points are given in Table 12. Logic levels: VOL and VOH are typical output voltage drop that occur with the output load. Fig 7. Turn-on and turn-off times 9397 750 14686 Product data sheet © Koninklijke Philips Electronics N.V. 2005. All rights reserved. Rev. 01 — 25 July 2005 14 of 20 74AUP1G126 Philips Semiconductors Low-power buffer/line driver; 3-state Table 12: Measurement points Supply voltage Input Output VCC VM VM VX VY 0.8 V to 1.6 V 0.5 × VCC 0.5 × VCC VOL + 0.1 V VOH − 0.1 V 1.65 V to 2.7 V 0.5 × VCC 0.5 × VCC VOL + 0.15 V VOH − 0.15 V 3.0 V to 3.6 V 0.5 × VCC 0.5 × VCC VOL + 0.3 V VOH − 0.3 V VCC VEXT 5 kΩ PULSE GENERATOR VI VO DUT RT CL RL 001aac521 Test data is given in Table 13. Definitions for test circuit: RL = Load resistor CL = Load capacitance including jig and probe capacitance RT = Termination resistance should be equal to the output impedance Zo of the pulse generator Fig 8. Load circuitry for switching times Table 13: Test data Supply voltage Load VCC CL 0.8 V to 3.6 V 5 pF, 10 pF, 5 kΩ or 1 MΩ open 15 pF and 30 pF [1] VEXT RL [1] tPZH, tPHZ tPZL, tPLZ GND 2 × VCC For measuring enable and disable times RL = 5 kΩ, for measuring propagation delays, setup and hold times and pulse width RL = 1 MΩ. 9397 750 14686 Product data sheet tPLH, tPHL © Koninklijke Philips Electronics N.V. 2005. All rights reserved. Rev. 01 — 25 July 2005 15 of 20 74AUP1G126 Philips Semiconductors Low-power buffer/line driver; 3-state 14. Package outline TSSOP5: plastic thin shrink small outline package; 5 leads; body width 1.25 mm E D SOT353-1 A X c y HE v M A Z 5 4 A2 A (A3) A1 θ 1 Lp 3 L e w M bp detail X e1 0 1.5 3 mm scale DIMENSIONS (mm are the original dimensions) UNIT A max. A1 A2 A3 bp c D(1) E(1) e e1 HE L Lp v w y Z(1) θ mm 1.1 0.1 0 1.0 0.8 0.15 0.30 0.15 0.25 0.08 2.25 1.85 1.35 1.15 0.65 1.3 2.25 2.0 0.425 0.46 0.21 0.3 0.1 0.1 0.60 0.15 7° 0° Note 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. OUTLINE VERSION SOT353-1 REFERENCES IEC JEDEC JEITA MO-203 SC-88A EUROPEAN PROJECTION ISSUE DATE 00-09-01 03-02-19 Fig 9. Package outline SOT353-1 (TSSOP5) 9397 750 14686 Product data sheet © Koninklijke Philips Electronics N.V. 2005. All rights reserved. Rev. 01 — 25 July 2005 16 of 20 74AUP1G126 Philips Semiconductors Low-power buffer/line driver; 3-state XSON6: plastic extremely thin small outline package; no leads; 6 terminals; body 1 x 1.45 x 0.5 mm SOT886 b 1 2 3 4× (2) L L1 e 6 5 e1 4 e1 6× A (2) A1 D E terminal 1 index area 0 1 2 mm scale DIMENSIONS (mm are the original dimensions) UNIT A (1) max A1 max b D E e e1 L L1 mm 0.5 0.04 0.25 0.17 1.5 1.4 1.05 0.95 0.6 0.5 0.35 0.27 0.40 0.32 Notes 1. Including plating thickness. 2. Can be visible in some manufacturing processes. OUTLINE VERSION SOT886 REFERENCES IEC JEDEC JEITA EUROPEAN PROJECTION ISSUE DATE 04-07-15 04-07-22 MO-252 Fig 10. Package outline SOT886 (XSON6) 9397 750 14686 Product data sheet © Koninklijke Philips Electronics N.V. 2005. All rights reserved. Rev. 01 — 25 July 2005 17 of 20 74AUP1G126 Philips Semiconductors Low-power buffer/line driver; 3-state 15. Abbreviations Table 14: Abbreviations Acronym Description CMOS Complementary Metal Oxide Semiconductor TTL Transistor Transistor Logic HBM Human Body Model ESD ElectroStatic Discharge MM Machine Model CDM Charged Device Model 16. Revision history Table 15: Revision history Document ID Release date Data sheet status Change notice Doc. number Supersedes 74AUP1G126_1 20050725 Product data sheet - 9397 750 14686 - 9397 750 14686 Product data sheet © Koninklijke Philips Electronics N.V. 2005. All rights reserved. Rev. 01 — 25 July 2005 18 of 20 74AUP1G126 Philips Semiconductors Low-power buffer/line driver; 3-state 17. Data sheet status Level Data sheet status [1] Product status [2] [3] Definition I Objective data Development This data sheet contains data from the objective specification for product development. Philips Semiconductors reserves the right to change the specification in any manner without notice. II Preliminary data Qualification This data sheet contains data from the preliminary specification. Supplementary data will be published at a later date. Philips Semiconductors reserves the right to change the specification without notice, in order to improve the design and supply the best possible product. III Product data Production This data sheet contains data from the product specification. Philips Semiconductors reserves the right to make changes at any time in order to improve the design, manufacturing and supply. Relevant changes will be communicated via a Customer Product/Process Change Notification (CPCN). [1] Please consult the most recently issued data sheet before initiating or completing a design. [2] The product status of the device(s) described in this data sheet may have changed since this data sheet was published. The latest information is available on the Internet at URL http://www.semiconductors.philips.com. [3] For data sheets describing multiple type numbers, the highest-level product status determines the data sheet status. 18. Definitions customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application. Short-form specification — The data in a short-form specification is extracted from a full data sheet with the same type number and title. For detailed information see the relevant data sheet or data handbook. Right to make changes — Philips Semiconductors reserves the right to make changes in the products - including circuits, standard cells, and/or software - described or contained herein in order to improve design and/or performance. When the product is in full production (status ‘Production’), relevant changes will be communicated via a Customer Product/Process Change Notification (CPCN). Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. Limiting values definition — Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 60134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information — Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or modification. 20. Trademarks 19. Disclaimers Notice — All referenced brands, product names, service names and trademarks are the property of their respective owners. Life support — These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips Semiconductors 21. Contact information For additional information, please visit: http://www.semiconductors.philips.com For sales office addresses, send an email to: [email protected] 9397 750 14686 Product data sheet © Koninklijke Philips Electronics N.V. 2005. All rights reserved. Rev. 01 — 25 July 2005 19 of 20 74AUP1G126 Philips Semiconductors Low-power buffer/line driver; 3-state 22. Contents 1 2 3 4 5 6 7 7.1 7.2 8 8.1 9 10 11 12 13 14 15 16 17 18 19 20 21 General description . . . . . . . . . . . . . . . . . . . . . . 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Quick reference data . . . . . . . . . . . . . . . . . . . . . 2 Ordering information . . . . . . . . . . . . . . . . . . . . . 2 Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Functional diagram . . . . . . . . . . . . . . . . . . . . . . 3 Pinning information . . . . . . . . . . . . . . . . . . . . . . 3 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 4 Functional description . . . . . . . . . . . . . . . . . . . 4 Function table . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 4 Recommended operating conditions. . . . . . . . 5 Static characteristics. . . . . . . . . . . . . . . . . . . . . 5 Dynamic characteristics . . . . . . . . . . . . . . . . . . 9 Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Package outline . . . . . . . . . . . . . . . . . . . . . . . . 16 Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Revision history . . . . . . . . . . . . . . . . . . . . . . . . 18 Data sheet status . . . . . . . . . . . . . . . . . . . . . . . 19 Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Contact information . . . . . . . . . . . . . . . . . . . . 19 © Koninklijke Philips Electronics N.V. 2005 All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent- or other industrial or intellectual property rights. Date of release: 25 July 2005 Document number: 9397 750 14686 Published in The Netherlands