SAMSUNG K9F2808U0M-YCB0

K9F2808U0M-YCB0, K9F2808U0M-YIB0
FLASH MEMORY
Document Title
16M x 8 Bit NAND Flash Memory
Revision History
Revision No. History
Draft Date
Remark
0.0
Initial issue.
April 10th 1998
Preliminary
1.0
1. Changed tPROG Parameter : 1ms(Max.) → 500µs(Max.)
2. Changed tBERS Parameter : 4ms(Max.) → 3ms(Max.)
3. Changed Input and Output Timing Level 0.8V and 2.0V → 1.5V
July 14th 1998
Final
1.1
1. Changed tR Parameter : 7µs(Max.) → 10µs(Max.)
2. Changed Nop : 10 cycles(Max.) → Main Array 2 cycles(Max.)
Spare Array 3 cycles(Max.)
3. Added CE don’t care mode during the data-loading and reading
April 10th 1999
Final
1.2
1. Revised real-time map-out algorithm(refer to technical notes)
June 30th 1999
Final
1.3
1. Changed device name
- KM29U128T -> K9F2808U0M-YCB0
- KM29U128IT -> K9F2808U0M-YIB0
Sep. 15th 1999
Final
1.4
1. Changed SE pin description
- SE is recommended to coupled to GND or Vcc and should not be
toggled during reading or programming.
July 17th 2000
Final
Note : For more detailed features and specifications including FAQ, please refer to Samsung’s Flash web site.
http://www.intl.samsungsemi.com/Memory/Flash/datasheets.html
The attached datasheets are prepared and approved by SAMSUNG Electronics. SAMSUNG Electronics CO., LTD. reserve the right
to change the specifications. SAMSUNG Electronics will evaluate and reply to your requests and questions about device. If you have
any questions, please contact the SAMSUNG branch office near you.
1
K9F2808U0M-YCB0, K9F2808U0M-YIB0
FLASH MEMORY
16M x 8 Bit NAND Flash Memory
FEATURES
GENERAL DESCRIPTION
• Voltage supply : 2.7V~3.6V
• Organization
- Memory Cell Array : (16M + 512K)bit x 8bit
- Data Register : (512 + 16)bit x8bit
• Automatic Program and Erase
- Page Program : (512 + 16)Byte
- Block Erase : (16K + 512)Byte
• 528-Byte Page Read Operation
- Random Access : 10µs(Max.)
- Serial Page Access : 50ns(Min.)
• Fast Write Cycle Time
- Program Time : 200µs(typ.)
- Block Erase Time : 2ms(typ.)
• Command/Address/Data Multiplexed I/O port
• Hardware Data Protection
- Program/Erase Lockout During Power Transitions
• Reliable CMOS Floating-Gate Technology
- Endurance : 1Million Program/Erase Cycles
- Data Retention : 10 years
• Command Register Operation
• Package : 48 - pin TSOP Type1 - 12 x 20 / 0.5 mm pitch
The K9F2808U0M is a 16M(16,777,216)x8bit NAND Flash
Memory with a spare 512K(524,288)x8bit. Its NAND cell provides the most cost-effective solution for the solid state mass
storage market. A program operation programs the 528-byte
page in typically 200µs and an erase operation can be performed in typically 2ms on a 16K-byte block. Data in the page
can be read out at 50ns cycle time per byte. The I/O pins serve
as the ports for address and data input/output as well as command inputs. The on-chip write controller automates all program and erase functions including pulse repetition, where
required, and internal verify and margining of data. Even the
write-intensive systems can take advantage of the
K9F2808U0M′s extended reliability of 1,000,000 program/erase
cycles by providing ECC(Error Correcting Code) with real time
mapping-out algorithm.
The K9F2808U0M is an optimum solution for large nonvolatile
storage applications such as solid state file storage, digital
voice recorder, digital still camera and other portable applications requiring non-volatility.
PIN CONFIGURATION
PIN DESCRIPTION
N.C
N.C
N.C
N.C
N.C
SE
R/B
RE
CE
N.C
N.C
Vcc
Vss
N.C
N.C
CLE
ALE
WE
WP
N.C
N.C
N.C
N.C
N.C
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
48-pin TSOP1
Standard Type
12mm x 20mm
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
N.C
N.C
N.C
N.C
I/O7
I/O6
I/O5
I/O4
N.C
N.C
N.C
Vcc
Vss
N.C
N.C
N.C
I/O3
I/O2
I/O1
I/O0
N.C
N.C
N.C
N.C
Pin Name
I/O0 ~ I/O7
Data Input/Outputs
CLE
Command Latch Enable
ALE
Address Latch Enable
CE
Chip Enable
RE
Read Enable
WE
Write Enable
WP
Write Protect
SE
Spare area Enable
R/B
Ready/Busy output
VCC
Power
VSS
Ground
N.C
No Connection
NOTE : Connect all VCC and V SS pins of each device to common power supply outputs.
Do not leave V CC or VSS disconnected.
2
Pin Function
K9F2808U0M-YCB0, K9F2808U0M-YIB0
FLASH MEMORY
Figure 1. FUNCTIONAL BLOCK DIAGRAM
VCC
VSS
Y-Gating
2nd half Page Register & S/A
X-Buffers
Latches
& Decoders
A9 - A23
128M + 4M Bit
NAND Flash
ARRAY
Y-Buffers
Latches
& Decoders
A0 - A7
(512 + 16)Byte x 32768
1st half Page Register & S/A
A8
Y-Gating
Command
Command
Register
CE
RE
WE
VCC
VSS
I/O Buffers & Latches
Control Logic
& High Voltage
Generator
Output
Driver
Global Buffers
I/0 0
I/0 7
CLE ALE WP
Figure 2. ARRAY ORGANIZATION
1 Block = 32 Row
(16K + 512) Bytes
32K Pages
(=1024 Blocks)
1st half Page Register
2nd half Page Register
(=256 Bytes)
(=256 Bytes)
1 Page = 528 Bytes
1 Block = 528 B x 32 Pages
= (16K + 512) Bytes
1 Device = 528B x 32Pages x 1024 Blocks
= 132 Mbits
8 bit
512 Bytes
16 Bytes
I/O 0 ~ I/O 7
Page Register
512 Bytes
1st Cycle
16 Bytes
I/O 0
I/O 1
I/O 2
I/O 3
I/O 4
I/O 5
I/O 6
I/O 7
A0
A1
A2
A3
A4
A5
A6
A7
2nd Cycle
A9
A10
A11
A12
A13
A14
A15
A16
3rd Cycle
A17
A18
A19
A20
A21
A22
A23
*X
NOTE : Column Address : Starting Address of the Register.
00h Command(Read) : Defines the starting address of the 1st half of the register.
01h Command(Read) : Defines the starting address of the 2nd half of the register.
* A8 is set to "Low" or "High" by the 00h or 01h Command.
* X can be High or Low.
3
Column Address
Row Address
(Page Address)
K9F2808U0M-YCB0, K9F2808U0M-YIB0
FLASH MEMORY
PRODUCT INTRODUCTION
The K9F2808U0M is a 132Mbit(138,412,032 bit) memory organized as 32,768 rows(pages) by 528 columns. Spare sixteen columns
are located from column address of 512 to 527. A 528-byte data register is connected to memory cell arrays accommodating data
transfer between the I/O buffers and memory during page read and page program operations. The memory array is made up of 16
cells that are serially connected to form a NAND structure. Each of the 16 cells resides in a different page. A block consists of the 32
pages formed by one NAND structures, totaling 8448 NAND structures of 16 cells. The array organization is shown in Figure 2. The
program and read operations are executed on a page basis, while the erase operation is executed on a block basis. The memory
array consists of 1024 separately erasable 16K-byte blocks. It indicates that the bit by bit erase operation is prohibited on the
K9F2808U0M.
The K9F2808U0M has addresses multiplexed into 8 I/O′s. This scheme dramatically reduces pin counts and allows systems
upgrades to future densities by maintaining consistency in system board design. Command, address and data are all written through
I/O′s by bringing WE to low while CE is low. Data is latched on the rising edge of WE. Command Latch Enable(CLE) and Address
Latch Enable(ALE) are used to multiplex command and address respectively, via the I/O pins. All commands require one bus cycle
except for Block Erase command which requires two cycles: one cycle for erase-setup and another for erase-execution after block
address loading. The 16M byte physical space requires 24 addresses, thereby requiring three cycles for byte-level addressing: column address, low row address and high row address, in that order. Page Read and Page Program need the same three address
cycles following the required command input. In Block Erase operation, however, only the two row address cycles are used. Device
operations are selected by writing specific commands into the command register. Table 1 defines the specific commands of the
K9F2808U0M.
Table 1. COMMAND SETS
Function
Read 1
1st. Cycle
2nd. Cycle
00h/01h
Read 2
50h
Acceptable Command during Busy
-
(1)
-
(2)
Read ID
90h
-
Reset
FFh
-
Page Program
80h
10h
Block Erase
60h
D0h
Read Status
70h
-
NOTE : 1. The 00h command defines starting address of the 1st half of registers.
The 01h command defines starting address of the 2nd half of registers.
After data access on the 2nd half of register by the 01h command, the status pointer is
automatically moved to the 1st half register(00h) on the next cycle.
2. The 50h command is valid only when the SE(pin 6) is low level.
4
O
O
K9F2808U0M-YCB0, K9F2808U0M-YIB0
FLASH MEMORY
PIN DESCRIPTION
Command Latch Enable(CLE)
The CLE input controls the path activation for commands sent to the command register. When active high, commands are latched
into the command register through the I/O ports on the rising edge of the WE signal.
Address Latch Enable(ALE)
The ALE input controls the activating path for address to the internal address registers. Addresses are latched on the rising edge of
WE with ALE high.
Chip Enable(CE)
The CE input is the device selection control. When CE goes high during a read operation the device is returned to standby mode.
However, when the device is in the busy state during program or erase, CE high is ignored, and does not return the device to
standby mode.
Write Enable(WE)
The WE input controls writes to the I/O port. Commands, address and data are latched on the rising edge of the WE pulse.
Read Enable(RE)
The RE input is the serial data-out control, and when active drives the data onto the I/O bus. Data is valid tREA after the falling edge
of RE which also increments the internal column address counter by one.
Spare Area Enable(SE)
The SE input controls the access of the spare area. When SE is high, the spare area is not accessible for reading or programming.
SE is recommended to be coupled to GND or Vcc and should not be toggled during reading or programming.
I/O Port : I/O 0 ~ I/O 7
The I/O pins are used to input command, address and data, and to output data during read operations. The I/O pins float to high-z
when the chip is deselected or when the outputs are disabled.
Write Protect(WP)
The WP pin provides inadvertent write/erase protection during power transitions. The internal high voltage generator is reset when
the WP pin is active low.
Ready/Busy(R/B)
The R/B output indicates the status of the device operation. When low, it indicates that a program, erase or random read operation is
in process and returns to high state upon completion. It is an open drain output and does not float to high-z condition when the chip
is deselected or when outputs are disabled.
5
K9F2808U0M-YCB0, K9F2808U0M-YIB0
FLASH MEMORY
ABSOLUTE MAXIMUM RATINGS
Parameter
Symbol
Voltage on any pin relative to VSS
Temperature Under Bias
K9F2808U0M-YCB0
Rating
VIN
-0.6 to + 4.6
VCC
-0.6 to + 4.6
V
-10 to +125
TBIAS
K9F2808U0M-YIB0
Storage Temperature
Unit
°C
-40 to +125
TSTG
°C
-65 to +150
NOTE :
1. Minimum DC voltage is -0.3V on input/output pins. During transitions, this level may undershoot to -2.0V for periods <30ns.
Maximum DC voltage on input/output pins is V CC+0.3V which, during transitions, may overshoot to VCC+2.0V for periods <20ns.
2. Permanent device damage may occur if ABSOLUTE MAXIMUM RATINGS are exceeded. Functional operation should be restricted to the conditions
as detailed in the operational sections of this data sheet. Exposure to absolute maximum rating conditions for extended periods may affect reliability.
RECOMMENDED OPERATING CONDITIONS
(Voltage reference to GND, K9F2808U0M-YCB0:TA=0 to 70°C, K9F2808U0M-YIB0 :TA=-40 to 85°C)
Parameter
Symbol
Min
Typ.
Max
Unit
Supply Voltage
VCC
2.7
3.3
3.6
V
Supply Voltage
VSS
0
0
0
V
DC AND OPERATING CHARACTERISTICS(Recommended operating conditions otherwise noted.)
Parameter
Operating
Current
Symbol
Test Conditions
Sequential Read
ICC1
tRC=50ns, CE=VIL, IOUT=0mA
Program
ICC2
-
Erase
ICC3
-
Min
Typ
Max
-
10
20
-
10
20
-
10
20
Stand-by Current(TTL)
ISB1
CE=VIH, WP=SE=0V/VCC
-
-
1
Stand-by Current(CMOS)
ISB2
CE=VCC-0.2, WP=SE=0V/V CC
-
10
50
Input Leakage Current
ILI
VIN=0 to 3.6V
-
-
±10
Output Leakage Current
ILO
VOUT=0 to 3.6V
-
-
±10
Input High Voltage
VIH
-
2.0
-
VCC+0.3
Input Low Voltage, All inputs
VIL
-
-0.3
-
0.8
Output High Voltage Level
VOH
IOH=-400µA
2.4
-
-
Output Low Voltage Level
VOL
IOL=2.1mA
-
-
0.4
Output Low Current(R/B)
IOL(R/B)
VOL=0.4V
8
10
-
6
Unit
mA
µA
V
mA
K9F2808U0M-YCB0, K9F2808U0M-YIB0
FLASH MEMORY
VALID BLOCK
Parameter
Valid Block Number
Symbol
Min
Typ.
Max
Unit
N VB
1004
-
1024
Blocks
NOTE :
1. The K9F2808U0M may include invalid blocks when first shipped. Additional invalid blocks may develop while being used. The number of valid
blocks is presented with both cases of invalid blocks considered. Invalid blocks are defined as blocks that contain one or more bad bits . Do not try
to access these invalid blocks for program and erase. Refer to the attached technical notes for a appropriate management of invalid blocks.
2. The 1st block, which is placed on 00h block address, is guaranteed to be a valid block
AC TEST CONDITION
(K9F2808U0M-YCB0:TA=0 to 70°C, K9F2808U0M-YIB0:T A=-40 to 85°C, VCC=2.7V~3.6V unless otherwise noted)
Parameter
Value
Input Pulse Levels
0.4V to 2.4V
Input Rise and Fall Times
5ns
Input and Output Timing Levels
1.5V
Output Load (3.0V +/-10%)
1 TTL GATE and CL=50pF
Output Load (3.3V +/-10%)
1 TTL GATE and CL=100pF
CAPACITANCE(TA=25°C, VCC=3.3V, f=1.0MHz)
Symbol
Test Condition
Min
Max
Unit
Input/Output Capacitance
Item
CI/O
VIL =0V
-
10
pF
Input Capacitance
CIN
VIN=0V
-
10
pF
NOTE : Capacitance is periodically sampled and not 100% tested.
MODE SELECTION
CLE
ALE
CE
WE
RE
SE
WP
H
L
L
H
X
X
L
H
L
H
X
X
H
L
L
H
X
H
L
H
L
H
X
H
H
Mode
Read Mode
Command Input
Address Input(3clock)
Write Mode
Command Input
Address Input(3clock)
L/H
(3)
L
L
L
L
L
L
H
H
Data Input
L/H
(3)
X
Sequential Read & Data Output
L/H
(3)
L
L
L
H
H
X
During Read(Busy)
(3)
X
X
X
X
X
L/H
H
During Program(Busy)
X
X
X
X
X
X
H
During Erase(Busy)
X
X(1)
X
X
X
X
L
Write Protect
X
X
H
X
X
0V/VCC(2) 0V/V CC(2) Stand-by
NOTE : 1. X can be V IL or VIH.
2. WP should be biased to CMOS high or CMOS low for standby.
3. When SE is high, spare area is deselected.
Program/Erase Characteristics
Parameter
Program Time
Number of Partial Program Cycles
in the Same Page
Block Erase Time
Main Array
Spare Array
Symbol
Min
Typ
Max
Unit
tPROG
-
200
500
µs
-
-
2
cycles
-
-
3
cycles
-
2
3
ms
Nop
tBERS
7
K9F2808U0M-YCB0, K9F2808U0M-YIB0
FLASH MEMORY
AC Timing Characteristics for Command / Address / Data Input
Parameter
Symbol
Min
Max
Unit
CLE Set-up Time
tCLS
0
-
ns
CLE Hold Time
tCLH
10
-
ns
CE Setup Time
tCS
0
-
ns
CE Hold Time
tCH
10
-
ns
WE Pulse Width
tWP
25
-
ns
ALE Setup Time
tALS
0
-
ns
ALE Hold Time
tALH
10
-
ns
Data Setup Time
tDS
20
-
ns
Data Hold Time
tDH
10
-
ns
Write Cycle Time
tWC
50
-
ns
WE High Hold Time
tWH
15
-
ns
AC Characteristics for Operation
Parameter
Symbol
Min
Max
Unit
tR
-
10
µs
Data Transfer from Cell to Register
ALE to RE Delay( ID read )
tAR1
100
-
ns
ALE to RE Delay(Read cycle)
tAR2
50
-
ns
CE to RE Delay( ID read)
tCR
100
-
ns
Ready to RE Low
tRR
20
-
ns
RE Pulse Width
tRP
30
-
ns
WE High to Busy
tWB
-
100
ns
Read Cycle Time
tRC
50
-
ns
RE Access Time
tREA
-
35
ns
RE High to Output Hi-Z
tRHZ
15
30
ns
CE High to Output Hi-Z
tCHZ
-
20
ns
RE High Hold Time
tREH
15
-
ns
tIR
0
-
ns
Last RE High to Busy(at sequential read)
tRB
-
100
ns
CE High to Ready(in case of interception by CE at read)
tCRY
-
50 +tr(R/B)(1)
ns
CE High Hold Time(at the last serial read) (2)
tCEH
100
-
ns
RE Low to Status Output
tRSTO
-
35
ns
CE Low to Status Output
tCSTO
-
45
ns
WE High to RE Low
tWHR
60
-
ns
Output Hi-Z to RE Low
RE access time(Read ID)
Device Resetting Time (Read/Program/Erase)
tREADID
-
35
ns
tRST
-
5/10/500
µs
NOTE :
1. The time to Ready depends on the value of the pull-up resistor tied R/B pin.
2. To break the sequential read cycle, CE must be held high for longer time than tCEH.
8
K9F2808U0M-YCB0, K9F2808U0M-YIB0
FLASH MEMORY
NAND Flash Technical Notes
Invalid Block(s)
Invalid blocks are defined as blocks that contain one or more invalid bits whose reliability is not guaranteed by Samsung. Typically,
an invalid block will contain a single bad bit. The information regarding the invalid block(s) is called as the invalid block information.
The invalid block information is written to the 1st or the 2nd page of the invalid block(s) with 00h data. Devices with invalid block(s)
have the same quality level or as devices with all valid blocks and have the same AC and DC characteristics. An invalid block(s)
does not affect the performance of valid block(s) because it is isolated from the bit line and the common source line by a select transistor. The system design must be able to mask out the invalid block(s) via address mapping. The 1st block of the NAND Flash, however, is fully guaranteed to be a valid block.
Identifying Invalid Block(s)
All device locations are erased(FFh) except locations where the invalid block information is written prior to shipping. Since the invalid
block information is also erasable in most cases, it is impossible to recover the information once it has been erased. Therefore, the
system must be able to recognize the invalid block(s) based on the original invalid block information and create the invalid block
table via the following suggested flow chart(Figure 1). Any intentional erasure of the original invalid block information is prohibited.
Start
Set Block Address = 0
Increment Block Address
Create (or update)
Invalid Block(s) Table
No
Check "FFh" ?
*
Check "FFh" on the 1st and 2nd page
Yes
No
Last Block ?
Yes
End
Figure 1. Flow chart to create invalid block table.
9
K9F2808U0M-YCB0, K9F2808U0M-YIB0
FLASH MEMORY
NAND Flash Technical Notes (Continued)
Error in write or read operation
Over its life time, the additional invalid blocks may develop with NAND Flash memory. Refer to the qualification report for the actual
data.The following possible failure modes should be considered to implement a highly reliable system. In the case of status read failure after erase or program, block replacement should be done. To improve the efficiency of memory space, it is recommended that
the read or verification failure due to single bit error be reclaimed by ECC without any block replacement. The said additional block
failure rate does not include those reclaimed blocks.
Failure Mode
Write
Read
ECC
Detection and Countermeasure sequence
Erase Failure
Status Read after Erase --> Block Replacement
Program Failure
Status Read after Program --> Block Replacement
Read back ( Verify after Program) --> Block Replacement
or ECC Correction
Single Bit Failure
Verify ECC -> ECC Correction
: Error Correcting Code --> Hamming Code etc.
Example) 1bit correction & 2bit detection
Program Flow Chart
If ECC is used, this verification
operation is not needed.
Start
Write 00h
Write 80h
Write Address
Write Address
Wait for tR Time
Write Data
Write 10h
Verify Data
Read Status Register
No
*
Program Error
Yes
Program Completed
I/O 6 = 1 ?
or R/B = 1 ?
*
Program Error
Yes
No
No
*
I/O 0 = 0 ?
Yes
10
: If program operation results in an error, map out
the block including the page in error and copy the
target data to another block.
K9F2808U0M-YCB0, K9F2808U0M-YIB0
FLASH MEMORY
NAND Flash Technical Notes (Continued)
Erase Flow Chart
Read Flow Chart
Start
Start
Write 60h
Write 00H
Write Block Address
Write Address
Write D0h
Read Data
Read Status Register
ECC Generation
No
I/O 6 = 1 ?
or R/B = 1 ?
*
Erase Error
Reclaim the Error
Verify ECC
Yes
Yes
No
No
Page Read Completed
I/O 0 = 0 ?
Yes
Erase Completed
*
: If erase operation results in an error, map out
the failing block and replace it with another block.
Block Replacement
Buffer
memory
error occurs
Page a
Block A
Block B
11
When the error happens with page "a" of Block "A", try
to write the data into another Block "B" from an external buffer. Then, prevent further system access to
Block "A" (by creating a "invalid block" table or other
appropriate scheme.)
K9F2808U0M-YCB0, K9F2808U0M-YIB0
FLASH MEMORY
Pointer Operation of K9F2808U0M
The K9F2808U0M has three modes to set the destination of the pointer. The pointer is set to "A" area by the "00h" command, to "B"
area by the "01h" command, and to "C" area by the "50h" command. Table 1 shows the destination of the pointer, and figure 2 shows
the block diagram of its operations.
"A" area
(00h plane)
"B" area
(01h plane)
256 Byte
256 Byte
"A"
"B"
"C" area
(50h plane)
Table 1. Destination of the pointer
Command
Pointer position
Area
00h
01h
50h
0 ~ 255 byte
256 ~ 511 byte
512 ~ 527 byte
1st half array(A)
2nd half array(B)
spare array(C)
16 Byte
"C"
Internal
Page Register
Pointer select
commnad
(00h, 01h, 50h)
Pointer
Figure 2. Block diagram of pointer Operation
Example of Programming with Successive Pointer Operation
(1) "A" area program
Address / Data input
50h
00h
"C" area
80h
10h
"A" area
Address / Data input
80h
(2) "B" area program
"A" area program
Address / Data input
00h
01h
"A" area
80h
10h
"B" area
Address / Data input
80h
"A" area program
Address / Data input
50h
"A" area
10h
"B" area program
(3) "C" area program
00h
10h
"A" area program
80h
10h
"C" area
Address / Data input
80h
"C" area program
Table 2. Pointer Status after each operation
Operation
Program
Pointer status after operation
With previous 00h, Device is set to 00h Plane
With previous 01h, Device is set to 00h Plane*
With previous 50h, Device is set to 50h Plane
Reset
"00h" Plane("A" area)
Power up
"00h" Plane("A" area)
* 01h command is valid just one time when it is used as a pointer for program/erase.
* Erase operation does not affect the pointer status. Previous pointer status is maintained.
12
10h
"C" area program
K9F2808U0M-YCB0, K9F2808U0M-YIB0
FLASH MEMORY
System Interface Using CE don’t-care.
For a easier system interface, CE may be inactive during the data-loading or sequential data-reading as shown below. The internal
528byte page registers are utilized as seperate buffers for this operation and the system design gets more flexible. In addition, for
voice or audio applications which use slow cycle time on the order of u-seconds, de-activating CE during the data-loading and reading would provide significant savings in power consumption.
Figure 3. Program Operation with CE don’t-care.
CLE
CE don’t-care
≈
≈
CE
WE
ALE
I/O0~7
80h
Start Add.(3Cycle)
Data Input
Data Input
(Min. 10ns)
10H
(Max. 45ns)
tCS
tCH
tCEA
CE
CE
tREA
RE
tWP
WE
I/O0~7
Timing requirements : If CE is is exerted high during data-loading,
tCS must be minimum 10ns and tWC must be increased accordingly.
out
Timing requirements : If CE is is exerted high during sequential
data-reading, the falling edge of CE to valid data(tCEA) must
be kept greater than 45ns.
Figure 4. Read Operation with CE don’t-care.
CLE
CE don’t-care
Must be held
low during tR.
≈
CE
RE
ALE
tR
R/B
WE
I/O 0~7
00H
Data Output(sequential)
Start Add.(3Cycle)
13
K9F2808U0M-YCB0, K9F2808U0M-YIB0
FLASH MEMORY
* Command Latch Cycle
CLE
tCLS
tCLH
tCS
tCH
CE
tWP
WE
tALH
tALS
ALE
tDH
tDS
Command
I/O0~7
* Address Latch Cycle
tCLS
CLE
tCS
tWC
tWC
CE
tWP
tWP
tWP
WE
tWH
tWH
tALH
tALS
ALE
tDS
I/O0~7
tDH
A0~A7
14
tDS
tDH
A 9~A 16
tDS
tDH
A17~A23
K9F2808U0M-YCB0, K9F2808U0M-YIB0
FLASH MEMORY
* Input Data Latch Cycle
tCLH
CLE
tCH
CE
tWC
tALS
tWP
tWP
≈
ALE
tWP
WE
tWH
tDH
tDS
tDH
tDS
tDH
≈
tDS
I/O0~7
DIN 511
DIN 1
≈
DIN 0
* Sequential Out Cycle after Read (CLE=L, WE=H, ALE=L)
tRC
≈
CE
tREH
≈
tREA
tREA
tCHZ*
tREA
RE
tRHZ
Dout
I/O0~7
Dout
≈
tRHZ*
Dout
≈
tRR
R/B
NOTES : Transition is measured ±200mV from steady state voltage with load.
This parameter is sampled and not 100% tested.
15
K9F2808U0M-YCB0, K9F2808U0M-YIB0
FLASH MEMORY
* Status Read Cycle
tCLS
CLE
tCLS
tCLH
tCS
CE
tCH
tWP
WE
tCSTO
tCHZ
tWHR
RE
tDH
tDS
I/O0~7
tIR
tRSTO
tRHZ
Status Output
70h
READ1 OPERATION (READ ONE PAGE)
CLE
tCEH
CE
tCHZ
tWC
WE
tWB
tCRY
tAR2
ALE
tRHZ
tRC
tR
≈
RE
I/O0~7
00h or 01h A0 ~ A7
A9 ~ A16
Column
Address
R/B
A17 ~ A23
Dout N
Page(Row)
Address
Busy
16
Dout N+1
Dout N+2
Dout N+3
≈ ≈
tRR
Dout 527
tRB
K9F2808U0M-YCB0, K9F2808U0M-YIB0
FLASH MEMORY
READ1 OPERATION(INTERCEPTED BY CE)
CLE
CE
WE
tWB
tCHZ
tAR2
ALE
tR
tRC
RE
tRR
I/O0~7
A9 ~ A16
00h or 01h A0 ~ A7
Column
Address
A17 ~ A23
Dout N
Dout N+1
Dout N+2
Dout N+3
Page(Row)
Address
Busy
R/B
READ2 OPERATION(READ ONE PAGE)
CLE
CE
WE
tR
tWB
tAR2
ALE
RE
I/O0~7
50h
A0 ~ A 7
Dout
511+M
A9 ~ A16 A17 ~ A23
R/B
Dout
511+M+1
≈
≈
tRR
Dout 527
Selected
Row
M Address
A0~A3 : Valid Address
A4~A7 : Don′t care
512
16
Start
address M
17
K9F2808U0M-YCB0, K9F2808U0M-YIB0
FLASH MEMORY
SEQUENTIAL ROW READ OPERATION
CLE
CE
WE
≈
ALE
I/O0~7
00h
Dout
N+1
Dout
N
A0 ~ A7 A9 ~ A16 A17 ~ A23
Dout
N+2
Dout
527
Dout
0
Busy
Busy
R/B
Dout
2
Dout
527
≈
Ready
Dout
1
≈
RE
M
M+1
Output
Output
N
PAGE PROGRAM OPERATION
CLE
CE
tWC
tWC
tWC
WE
tWB
tPROG
ALE
I/O0~7
80h
A0 ~ A7 A9 ~ A16 A17 ~ A23
Sequential Data Column
Input Command Address
Page(Row)
Address
Din
N
Din
N+1
≈≈
RE
1 up to 528 Byte Data
Serial Input
10h
70h
Program
Command
Read Status
Command
≈
R/B
Din
527
18
I/O0
I/O0=0 Successful Program
I/O0=1 Error in Program
K9F2808U0M-YCB0, K9F2808U0M-YIB0
FLASH MEMORY
BLOCK ERASE OPERATION (ERASE ONE BLOCK)
CLE
CE
tWC
tWC
WE
tBERS
tWB
ALE
RE
I/O 0~7
60h
A9 ~ A16 A17 ~ A23
DOH
70h
I/O 0
Busy
R/B
Auto Block Erase Setup Command
≈
Page(Row)
Address
Erase Command
Read Status
Command
MANUFACTURE & DEVICE ID READ OPERATION
CLE
CE
WE
ALE
RE
tREADID
I/O 0 ~ 7
90h
Read ID Command
00h
ECh
Address 1 Cycle
Maker Code
19
73h
Device Code
I/O0=0 Successful Erase
I/O0=1 Error in Erase
K9F2808U0M-YCB0, K9F2808U0M-YIB0
FLASH MEMORY
DEVICE OPERATION
PAGE READ
Upon initial device power up, the device defaults to Read1 mode. This operation is also initiated by writing 00H to the command register along with three address cycles. Once the command is latched, it does not need to be written for the following page read operation. Three types of operations are available : random read, serial page read and sequential row read.
The random read mode is enabled when the page address is changed. The 528 bytes of data within the selected page are transferred to the data registers in less than 10µs(tR). The system controller can detect the completion of this data transfer(tR) by analyzing the output of R/B pin. Once the data in a page is loaded into the registers, they may be read out in 50ns cycle time by sequentially
pulsing RE. High to low transitions of the RE clock output the data stating from the selected column address up to the last column
address(column 511 or 527 depending on the state of SE pin).
After the data of last column address is clocked out, the next page is automatically selected for sequential row read.
Waiting 10µs again allows reading the selected page. The sequential row read operation is terminated by bringing CE high. The
way the Read1 and Read2 commands work is like a pointer set to either the main area or the spare area. The spare area of bytes
512 to 527 may be selectively accessed by writing the Read2 command with SE pin low. Toggling SE during operation is prohibited.
Addresses A0 to A3 set the starting address of the spare area while addresses A4 to A7 are ignored. Unless the operation is aborted,
the page address is automatically incremented for sequential row read as in Read1 operation and spare sixteen bytes of each page
may be sequentially read. The Read1 command(00h/01h) is needed to move the pointer back to the main area. Figures 3 thru 6
show typical sequence and timings for each read operation.
Figure 3. Read1 Operation
CLE
CE
WE
ALE
tR
R/B
RE
I/O0~7
00h
Start Add.(3Cycle)
Data Output(Sequential)
A0 ~ A7 & A9 ~ A23
(00h Command)
1st half array
(01h Command)*
2st half array
Data Field
Spare Field
1st half array
2st half array
Data Field
Spare Field
* After data access on 2nd half array by 01h command, the start pointer is automatically moved to 1st half
array (00h) at next cycle.
20
K9F2808U0M-YCB0, K9F2808U0M-YIB0
FLASH MEMORY
Figure 4. Read2 Operation
CLE
CE
WE
ALE
tR
R/B
RE
I/O 0~7
50h
Start Add.(3Cycle)
Data Output(Sequential)
A0 ~ A3 & A9 ~ A23
Spare Field
(A4 ~ A7 :
Don′t Care)
Seek Time
Data Field
Spare Field
tR
≈
Figure 5. Sequential Row Read1 Operation
tR
tR
R/B
I/O0 ~ 7
00h
Start Add.(3Cycle)
01h
Data Output
Data Output
1st
2nd
(528 Byte)
Nth
(528 Byte)
A0 ~ A7 & A9 ~ A23
(SE=L, 01h Command)
(SE=L, 00h Command)
1st half array
Data Output
1st half array
2nd half array
Data Field
(SE=H, 00h Command)
2nd half array
1st half array
2nd half array
1st
2nd
1st
2nd
1st
2nd
Nth
Nth
Nth
Spare Field
Data Field
21
Spare Field
Data Field
Spare Field
K9F2808U0M-YCB0, K9F2808U0M-YIB0
FLASH MEMORY
I/O0~7
tR
tR
R/B
50h
≈
Figure 6. Sequential Row Read2 Operation (SE=fixed low)
Start Add.(3Cycle)
tR
Data Output
Data Output
Data Output
2nd
(16Byte)
1st
A0 ~ A3 & A9 ~ A23
Nth
(16Byte)
(A4 ~ A7 :
Don ′t Care)
1st
2nd
Nth
Data Field
Spare Field
PAGE PROGRAM
The device is programmed basically on a page basis, but it does allow multiple partial page programing of a byte or consecutive
bytes up to 528, in a single page program cycle. The number of consecutive partial page programming operation within the same
page without an intervening erase operation should not exceed 2 for main array and 3 for spare array. The addressing may be done
in any random order in a block. A page program cycle consists of a serial data loading period in which up to 528 bytes of data may be
loaded into the page register, followed by a non-volatile programming period where the loaded data is programmed into the appropriate cell. Serial data loading can be started from 2nd half array by moving pointer. About the pointer operation, please refer to the
attached technical notes.
In order to serial data loading period begins by inputting the Serial Data Input command(80h), followed by the three cycle address
input and then serial data loading. The bytes other than those to be programmed do not need to be loaded.The Page Program confirm command(10H) initiates the programming process. Writing 10H alone without previously entering the serial data will not initiate
the programming process. The internal write controller automatically executes the algorithms and timings necessary for program and
verify, thereby freeing the CPU for other tasks. Once the program process starts, the Read Status Register command may be
entered, with RE and CE low, to read the status register. The CPU can detect the completion of a program cycle by monitoring the
R/B output, or the Status bit(I/O 6) of the Status Register. Only the Read Status command and Reset command are valid while programming is in progress. When the Page Program is complete, the Write Status Bit(I/O 0) may be checked(Figure 7). The internal
write verify detects only errors for "1"s that are not successfully programmed to "0"s. The command register remains in Read Status
command mode until another valid command is written to the command register.
Figure 7. Program & Read Status Operation
tPROG
R/B
I/O0~7
80h
Address & Data Input
10h
70h
A0 ~ A7 & A9 ~ A23
528 Byte Data
I/O0
Fail
22
Pass
K9F2808U0M-YCB0, K9F2808U0M-YIB0
FLASH MEMORY
BLOCK ERASE
The Erase operation is done on a block(16K Byte) basis. Block address loading is accomplished in two cycles initiated by an Erase
Setup command(60h). Only address A14 to A23 is valid while A9 to A13 is ignored. The Erase Confirm command(D0h) following the
block address loading initiates the internal erasing process. This two-step sequence of setup followed by execution command
ensures that memory contents are not accidentally erased due to external noise conditions.
At the rising edge of WE after the erase confirm command input, the internal write controller handles erase, erase-verify and pulse
repetition where required. When the erase operation is completed, the Write Status Bit(I/O 0) may be checked.
Figure 8 details the sequence.
Figure 8. Block Erase Operation
tBERS
R/B
I/O 0~7
60h
Address Input(2Cycle)
I/O0
70h
D0h
Pass
Block Add. : A 9 ~ A23
Fail
READ STATUS
The device contains a Status Register which may be read to find out whether program or erase operation is completed, and whether
the program or erase operation is completed successfully. After writing 70h command to the command register, a read cycle outputs
the content of the Status Register to the I/O pins on the falling edge of CE or RE, whichever occurs last. This two line control allows
the system to poll the progress of each device in multiple memory connections even when R/B pins are common-wired. RE or CE
does not need to be toggled for updated status. Refer to table 2 for specific Status Register definitions. The Pass/Fail status on I/O 0
is only valid when the device is in the Ready state. The command register remains in Status Read mode until further commands are
issued to it. Therefore, if the status register is read during a random read cycle, a read command(00H or 50h) should be given before
sequential page read cycle.
Table2. Read Status Register Definition
I/O #
I/O 0
Status
Definition
"0" : Successful Program / Erase
Program / Erase
"1" : Error in Program / Erase
I/O 1
I/O 2
I/O 3
"0"
"0"
Reserved for Future
Use
"0"
I/O 4
"0"
I/O 5
"0"
I/O 6
Device Operation
I/O 7
Write Protect
23
"0" : Busy
"1" : Ready
"0" : Protected
"1" : Not Protected
K9F2808U0M-YCB0, K9F2808U0M-YIB0
FLASH MEMORY
READ ID
The device contains a product identification mode, initiated by writing 90h to the command register, followed by an address input of
00H. Two read cycles sequentially output the manufacture code(ECh), and the device code (73h) respectively. The command register
remains in Read ID mode until further commands are issued to it. Figure 9 shows the operation sequence.
Figure 9. Read ID Operation
CLE
tCR
CE
WE
tAR1
ALE
RE
I/O0~7
tREADID
90h
00h
ECh
Address. 1cycle
Maker code
73h
Device code
RESET
The device offers a reset feature, executed by writing FFh to the command register. When the device is in Busy state during random
read, program or erase mode, the reset operation will abort these operations. The contents of memory cells being altered are no
longer valid, as the data will be partially programmed or erased. The command register is cleared to wait for the next command, and
the Status Register is cleared to value C0h when WP is high. Refer to table 3 for device status after reset operation. If the device is
already in reset state a new reset command will not be accepted by the command register. The R/B pin transitions to low for tRST
after the Reset command is written. Reset command is not necessary for normal operation. Refer to Figure 10 below.
Figure 10. RESET Operation
tRST
R/B
I/O0~7
FFh
Table3. Device Status
Operation Mode
After Power-up
After Reset
Read 1
Waiting for next command
24
K9F2808U0M-YCB0, K9F2808U0M-YIB0
FLASH MEMORY
READY/BUSY
The device has a R/B output that provides a hardware method of indicating the completion of a page program, erase and random
read completion. The R/B pin is normally high but transitions to low after program or erase command is written to the command register or random read is started after address loading. It returns to high when the internal controller has finished the operation. The pin
is an open-drain driver thereby allowing two or more R/B outputs to be Or-tied. An appropriate pull-up resister is required for proper
operation and the value may be calculated by the following equation.
Rp
VCC
VCC(Max.) - VOL(Max.)
Rp =
R/B
open drain output
IOL +ΣIL
3.2V
=
8mA + ΣIL
where IL is the sum of the input currents of all devices tied to the
R/B pin.
GND
Device
DATA PROTECTION
The device is designed to offer protection from any involuntary program/erase during power-transitions. An internal voltage detector
disables all functions whenever Vcc is below about 2V. WP pin provides hardware protection and is recommended to be kept at VIL
during power-up and power-down as shown in Figure 11. The two step command sequence for program/erase provides additional
software protection.
≈
Figure 11. AC Waveforms for Power Transition
~ 2.5V
VCC
≈
High
WP
25
~ 2.5V
Package Dimensions
FLASH MEMORY
PACKAGE DIMENSIONS
48-PIN LEAD PLASTIC THIN SMALL OUT-LINE PACKAGE TYPE(I)
Unit :mm/Inch
0.10
MAX
0.004
48 - TSOP1 - 1220F
#48
#24
#25
0.50
0.0197
12.40
MAX
0.488
( 0.25 )
0.010
#1
12.00
0.472
+0.003
0.008-0.001
0.20 -0.03
+0.07
20.00 ±0.20
0.787±0.008
1.00±0.05
0.039 ±0.002
+0.075
0~8¡Æ
0.45~0.75
0.018~0.030
+0.003
0.005-0.001
18.40 ±0.10
0.724±0.004
0.125 0.035
0.25
0.010 TYP
1.20
0.047 MAX
( 0.50 )
0.020
26
0.05
MIN
0.002