Ordering number : ENN5905A Monolithic Linear IC LA4663 Two-Channel 16-W BTL General-Purpose Audio Power Amplifier Overview The LA4663 is a BTL 2-channel power amplifier IC that was developed for ease of use in general audio applications. In addition to providing improvements in a wide range of electrical characteristics, the LA4663 aims for improved listenability and an excellent costperformance ratio. (The startup time can be modified in end products by using this circuit in conjunction with the muting circuit described above.) • Full complement of built-in protection circuits (protection from shorting to ground, shorting to VCC, load shorting, and overheating) • High audio quality, minimal impulse noise Applications Package Dimensions Radio/cassette players with built-in CD/MD players, microcomponent stereo systems, active speakers, electronic musical instruments, and other audio devices. unit: mm 3113A-SIP14HZ [LA4663] Features 4.0 11.8 14.5max 5.2 4.6 8.4 7.8 • Wide operating supply voltage range (VCCop): 5.5 to 22 V (Certain conditions may apply.) • High ripple rejection ratio: 60 dB (typical) • Power: 16 W × 2 (VCC = 15 V/6Ω), 13 W × 2 (VCC = 12 V/4Ω), 6.5 W × 2 (VCC = 9 V/4Ω) • Built-in signal muting circuit (AC muting) reduces the number of external components and provides muting with minimal switching noise. • Startup circuit with a start time of 0.6 to 0.7 seconds. The LA4663 provides distortion-free startup, since output is only generated after the supply voltage reaches the midpoint at power on. R1.7 27.0 20.0 1 1.94 0.5 14 0.4 1.6 3.56 1.78 2.2 3.56 SANYO: SIP14HZ Specifications Maximum Ratings at Ta = 25°C Parameter Symbol Maximum supply voltage VCC max Maximum output current Allowable power dissipation Conditions Ratings Unit No signal 24 IO peak Per channel 3.5 V A Pd max With an arbitrarily large heat sink 37.5 W Operating temperature Topr –20 to +75 °C Storage temperature Tstg –40 to +150 °C Any and all SANYO products described or contained herein do not have specifications that can handle applications that require extremely high levels of reliability, such as life-support systems, aircraft’s control systems, or other applications whose failure can be reasonably expected to result in serious physical and/or material damage. Consult with your SANYO representative nearest you before using any SANYO products described or contained herein in such applications. SANYO assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all SANYO products described or contained herein. SANYO Electric Co.,Ltd. Semiconductor Company TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110-8534 JAPAN 42800TN (OT)/70898RM (OT) No. 5905-1/10 LA4663 Operating Conditions *1 at Ta = 25°C Parameter Symbol Recommended supply voltage Recommended load resistance range Allowable operating supply voltage range *2 Conditions Ratings Unit VCC 12, 15 V RL op 4 to 8 Ω When RL = 8 Ω 5.5 to 21 V When RL = 6 Ω 5.5 to 20 V When RL = 5 Ω 5.5 to 17 V When RL = 4 Ω 5.5 to 15 V VCC op Note *:1. When used with VCC, RL, and output level ranges such that Pd max for the heat sink actually used is not exceeded. 2. When both channels are operating with IO peak values that exceed 2 A per channel. If the IO peak value does not exceed 2 A per channel, a range of 5.5 to 22 V is allowed for any allowable RL (for ranges where Pd max is not exceeded). Operating Characteristics at Ta = 25°C, VCC = 15 V, RL = 4 Ω, f = 1 kHz, Rg = 600 Ω Parameter Symbol Ratings Conditions min Quiescent current ICCO Rg = 0, RL = open 60 Standby current Ist When standby is off and with no power supply capacitor Voltage gain VG VO = 0 dBm Total harmonic distortion Output power Output offset voltage 38 THD PO = 1 W, Filter = FLAT PO1 VCC = 15 V, THD = 10%, RL = 4 Ω PO2 PO3 VN offset 16 max 100 180 1 10 µA 40 42 dB 0.07 0.4 VCC = 12 V, THD = 10%, RL = 4 Ω 13 W VCC = 12 V, THD = 10%, RL = 6 Ω 10 Rg = 0 W –300 VNO SVRR Rg = 0, VR = 0 dBm, fR = 100 Hz 50 60 Channel separation CH sep Rg = 10 kΩ, VO = 0 dBm 50 60 14 20 Rg = 0, BPF = 20 Hz to 20 kHz +300 mV 0.5 mV 0.2 Ri dB dB 26 kΩ V Standby pin applied voltage VST Amplifier on (the pin 5 voltage) 2.5 10 Muting pin applied voltage VM Muting on (the pin 6 voltage) 1.5 3 Muting on (VO = 1 V rms), BPF = 20 Hz to 20 kHz 70 ATTM Pd max - Ta 35 With an arbitrarily large heat sink 30 25 20.8 θf=3°C/W 20 15 13.9 10.4 θf=7°C/W θf=10°C/W 10 5 No radiator fin 3.1 0 -20 0 20 40 60 80 100 120 Ambient temperature, Ta — °C 140 dB Al heat sink, t = 1.5 mm With mounting bolts tightened down with a torque of 39 N·cm and silicone grease applied. 2 10 θjc=2°C/W θf=4°C/W V 80 θf - Sf 3 With an Al heat sink with mounting bolts tightened down with a torque of 39 N·cm and silicone grease applied. Heat sink thermal resistance, θf — °C/W Allowable power dissipation, Pd max — W 40 % W Ripple rejection ratio Muting attenuation mA 20 Output noise voltage Input resistance Unit typ 160 7 5 3 2 2 3 5 7 100 2 3 5 7 1000 Heat sink area, Sf — cm2 No. 5905-2/10 LA4663 Usage Notes 1. Maximum ratings If the device is operated in the vicinity of the maximum ratings, it is possible for small changes in the operating conditions to result in the maximum ratings being exceeded. Since this can result in destruction of the device, applications should be designed with adequate margins in the supply voltage and other parameters so that the maximum ratings are never exceeded during device operation. 2. Protection circuits While the LA4663 includes a full complement of built-in protection circuits, care is required in the usage. In particular, be careful not to short any pairs of device pins together. [Notes on the shorting (power, ground, and load shorting) protection circuit] • This protection circuit operates whenever a power short (a short between the output and VCC), a ground short (a short between the output and ground), or a load short (shorting between the + and – outputs) is detected. Although there are cases where the protection circuit may not operate if the supply voltage is under 9 V, the thermal protection circuit will protect the device in this range. • The protection circuit continues to operate during the interval that the abnormal short continues, and automatically recovers when the error state is resolved. However, under certain usage conditions, there are situations where the protection circuit may lock and remain locked even after the problem has been resolved. In these cases, the circuit can be reset by switching to standby mode or turning off the power temporarily. • If the output is shorted to VCC with the IC in the standby state and furthermore, a VCC of 20 V or higher applied, an offset will be created between the + and – outputs. If a load is connected in this state, a current will flow in that load, and the IC may be destroyed. Applications should assure that this does not occur. • In the following situations, the operation of the protection circuit may result in a sound switching phenomenon at high output levels. This may be a problem, depending on the details of the end product circuit itself, and must be verified in an actual system. • At low load resistances RL (high loads) and at high VCC voltages, and with both channels operating at IO peak levels of over 2 A per channel. (This phenomenon is more likely to occur the higher the chip temperature.) For systems operating under the most sever conditions (high temperatures and high outputs), specific operating conditions such that the above phenomenon does no occur are listed in the “Allowable operating supply voltage range (VCC op)” item in the Operating Conditions section of the specifications. (Refer to the VCC op ranges for different RL values.) [Thermal protection circuit] • A thermal protection circuit is provided to prevent damage to or destruction of the IC itself when the IC generates abnormally high temperatures. This means that gradual attenuation is applied to the output signals by the thermal protection circuit if the IC junction temperature (Tj) rises above about 160°C due to insufficient heat sinking or other problems. 3. Notes on printed circuit boards • When designing the printed circuit board pattern, keep the input lines separated from both the VCC lines and the output lines. This is to prevent increased distortion and oscillation. • When high output levels are used, make power-ground lines as wide as possible and as short as possible to prevent the PWR GND pins potential from increasing with respect to pre-ground. (From the standpoint of IC stability, ideally, the ground pin potential should be the lowest potential in the system. This is to prevent trouble caused by several types of induced parasitic devices due to increases in the GND pin potential due to the structure of the IC.) No. 5905-3/10 LA4663 4. Notes on heat sink mounting • Use a tightening torque of between 39 and 59 N·cm. • Make the spacing of the heat sink mounting screw holes the same as the spacing of the IC mounting screw holes. Also, make the mounting screw hole spacing as short as possible within the range that still allows mounting, referring to the external dimensions L and R. L R + + A10629 • For mounting screws, use screws that correspond to either the truss screws or binding screws stipulated by the JIS (Japan Industrial Standards). Use washers to protect the IC case. • Do not allow any foreign matter, such as machining chips, to get between the IC (package internal) heat sink and the external heat sink. Also, if grease is applied to the junction, apply the grease as evenly as possible. 5. Other notes • The LA4663 is a BTL power amplifier IC. When connecting this IC to test equipment, do not allow the test equipment grounds for the input and output systems to be shared grounds. No. 5905-4/10 LA4663 Equivalent Circuit Block Diagram +5 V VCC + SIGNAL MUTE R1 22 kΩ – 5 7 8 STAND BY VCC1 VCC2 C5 2200 µF 25 V 6 + +5 V – C4 10 µF 10 V CH 1 +OUT1 C1 4.7 µF 10 V – 14 + 2 Output amplifier PWR 13 GND1 – Ri = 20 kΩ PRE GND –OUT1 Input amplifier + 12 R3 2.2 Ω 3 C7 0.1 µF ** VCC/ground shorting protection circuit Load shorting protection circuit Thermal protection circuit — Protection circuits — Polyester film capacitors Input amplifier IN2 R2 2.2 Ω ** +OUT2 – RL = 4 to 8 Ω ** IN1 + C2 4.7 µF 10 V C6 0.1 µF 9 C8 0.1 µF RL = 4 to 8 Ω ** + 4 PWR 10 GND2 Output amplifier – R4 2.2 Ω R5 2.2 Ω ** Ri = 20 kΩ –OUT2 11 CH 2 C9 0.1 µF Ripple Filter/ Starting Time 1 + – C3 47 µF 25 V A10630 Pin Voltages at VCC = 15 V, with 5 V applied to the STBY pin (pin 5), using a digital volt meter. Pin No. Pin Pin voltage (V) Pin No. Pin Pin voltage (V) 1 2 3 4 5 6 7 RF IN1 PRE-GND IN2 STAND-BY MUTE VCC1 14.32 3m 0 3m 5 21m 15 8 9 10 11 12 13 14 VCC2 +OUT2 PWR-GND2 –OUT2 –OUT1 PWR-GND1 +OUT1 15 6.84 0 6.84 6.84 0 6.84 No. 5905-5/10 LA4663 External Components C1 and C2 • These are input coupling capacitors, and we recommend that values under 4.7 µF be used. The LA4663 uses a zero bias type input circuit, and the input pin potential is about zero volts. Determine the polarity orientation of these capacitors based on the DC current from the circuit connected to the LA4663 front end. If the potential difference between across the + and – leads on the input capacitors is large, the charge time for the input capacitors can be reduced by using as small a value as possible without causing degradation of the low band frequency characteristics. This will shorten the time required to reach stable operation when power is first applied. C3 *1 • This capacitor functions both as a ripple filter and as the amplifier starting time capacitor. We recommend a value of 47 µF. When the recommended value is used, the BTL SVRR between outputs will be about 63 dB, and that between the outputs and ground will be about 47 dB. (These are values are for reference purposes.) Similarly, the starting time (the time between the point power is first applied and the point an output is generated) will be around 0.6 to 0.7 seconds. C4 and R1 *2 • These form an CR circuit used for muting function smoothing. C4 is required even if the muting function is not used. C5 • Power supply capacitor C6 to C9 and R2 to R5 • These components for oscillation prevention CR circuits. We recommend the use of polyester film capacitors (Mylar capacitors) with excellent temperature characteristics for C6 through C9. (R2 to R5 should all be 2.2-Ω 1/4-W resistors.) Notes: 1. Starting time • The LA4663 includes a built-in starting time circuit. The starting time can be varied somewhat by modifying the value of the external capacitor connected to pin 1. With the recommended value of 47 µF, the starting time will be between 0.6 and 0.7 second (although this will vary with the supply voltage, VCC) and this time can be lengthened to about 0.9 second by inserting a 10 µF capacitor in parallel. • We do not recommend using a value smaller than the recommended value for the pin 1 capacitor, since that could result in reducing the SVRR with respect to ground. 2. Signal muting function • When the recommended CR circuit (10 µF and 22 kΩ) is connected to pin 6, the signal muting function can be turned on, and a muting function with minimal impulse noise applied by applying a voltage of 5V. • The CR circuit determines the attack and recovery times for smoothing function. Note that this 10-µF capacitor is required even when the signal muting function is not used, since it is also used for smoothing after the starting time has elapsed.The influx current to pin 6 when this external resistor has a value of 22 kΩ will be about 170 µA when the applied voltage is +5 V. Although it is possible to modify the value of this resistor if a different applied voltage or if the capacity of the I microcontroller required it, it is possible for the level of the +5 V 22 kΩ 6 About 1.56 V impulse noise associated with the muting function to increase + if the pin 6 influx current becomes excessive. Be sure to take 10 µF – this influx current into account if the value of this resistor is modified. A10631 No. 5905-6/10 LA4663 Other Notes • Standby function VSTB Pin 5 in this IC is the standby pin, and applying a voltage of 2.0 V or higher will activate this function. The pin 5 influx current for an applied voltage of 5 V will be about 240 µA. About 1.4 V ISTB 5 (RSTB) 15 kΩ ISTB = 5 V – 1.4 V = 240 µA 15 k Insert an external current limiting resistor (RSTB) if it is necessary to limit this influx current when using a microcontroller. A10632 If this input voltage is applied by a circuit or device other than a microcontroller, calculate the value for RSTB from the following formula such that the pin 5 influx current due to the applied VSTB is under 500 µA. RSTB = Applied voltage (VSTB) – 1.4 V – 15 kΩ 500 µA Sample Printed Circuit Board Pattern (Copper surface) 14 1 VCC C5 IN1 C3 GND C1 PRE-GND —OUT1 R3 OUT2 C2 C4 OUT1 —OUT2 IN2 C7 R2 C6 R5 C9 R4 C8 GND R1 STBY MUTE No. 5905-7/10 LA4663 I CCO - VCC PO - VCC 40 f=1kHz 36 THD=10% Rg=600Ω RL=Open 140 Rg=0 VSTB= 5V 32 80 60 40 4Ω 12 4 4 8 12 16 20 24 0 4 28 6 8 10 Total harmonic distortion, THD — % 3 2 Both channels operating Filter= FLAT 1.0 7 5 f=10kHz 3 2 0.1 7 5 f=1kHz 3 2 0.1 f=100Hz 2 3 5 7 1.0 2 3 5 7 10 2 3 THD - PO (RL=8Ω) 5 3 2 Both channels operating Filter =FLAT 1.0 7 5 3 2 f=10kHz 0.1 7 5 3 2 0.1 f=1kHz f=100Hz 2 3 5 7 1.0 2 3 5 7 10 2 3 24 1.0 7 5 f=10kHz 3 2 0.1 7 5 3 2 0.1 f=1kHz f=100Hz 2 3 5 7 1.0 2 3 5 7 10 2 3 THD - f VCC=15V 2 RL=4Ω Rg=600Ω 1.0 PO=1W 7 5 Both channels operating Filter= FLAT 3 2 0.1 7 5 3 2 10 2 3 5 7 100 2 3 5 7 1k 2 3 5 710k 2 3 5 7100k 2 Input frequency, f — Hz f Response PO - f 28 VCC=15V 26 RL=4Ω Rg=600Ω Output power, PO — W VCC=15V 3 RL=4Ω 2 Rg=600Ω VO=0dBm 1 0 -1 22 Filter= FLAT Output power, PO — W 4 20 Both channels operating 3 Total harmonic distortion, THD — % 3 2 18 Output power, PO — W VCC=15V 10 RL=8Ω 7 R =600Ω g 5 16 VCC=15V 10 RL=6Ω 7 Rg=600Ω Output power, PO — W 2 14 THD - PO (RL=6Ω) 2 VCC=15V 10 RL=4Ω 7 R =600Ω g 5 12 Supply voltage, VCC — V THD - PO (RL=4Ω) 2 Total harmonic distortion, THD — % 6Ω 16 Supply voltage, VCC — V Total harmonic distortion, THD — % Ω =8 RL 20 8 20 0 0 Response — dB L= L= 24 R 100 Both channels operating 28 R 120 Output power, PO — W Quiescent current, ICCO — mA 160 Both channels operating -2 -3 -4 -5 24 Both channels operating 22 THD=10% 20 18 16 THD=1% 14 -6 12 -7 10 10 10 2 3 5 7 100 2 3 5 7 1k 2 3 5 710k 2 3 5 7100k 2 Input frequency, f — Hz 2 3 5 7 100 2 3 5 7 1k 2 3 5 7 10k 2 3 5 Input frequency, f — Hz No. 5905-8/10 LA4663 CH sep. - f -30 -40 2 CH 1 -50 CH 1 H2 CH C -60 -70 -80 -90 10 2 3 5 7 100 2 3 5 7 1k VNO - R g 0.5 VCC=15V RL=4Ω Rg=10kΩ VO=0dBm Output noise voltage, VNO — mV rms Channel separation, CHsep. — dB -20 VCC=15V RL=4Ω DIN AUDIO 0.4 0.3 0.2 0.1 0 100 2 3 5 7 10k 2 3 5 7 100k 2 2 3 5 7 1k -20 SVRR - VCC With a 1-µF power supply capacitor -40 CH1 -60 CH2 -80 -100 4 6 8 10 12 14 16 18 20 22 24 -20 2 With a 1-µF power supply capacitor CH1 -60 CH2 -80 2 3 5 7100 2 3 5 7 1k 2 3 5 7 10k 2 3 5 7 Ripple frequency, fR — Hz SVRR - VCCR 32 VCC=15V RL=4Ω Rg=0 fR=100Hz 28 With a 1-µF power supply capacitor Calculated as SVRR = 20·log VO/VCCR -40 -60 -80 24 Pd - PO (RL=4Ω) f=1kHz RL=4Ω Both channels operating Calculated as Pd = VCC × ICC – 2·PO VCC=15V 20 VCC=12V 16 12 8 4 -100 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 0 3 2.2 5 7 0.1 2 28 Pd - PO (RL=6Ω) 32 f=1kHz RL=6Ω 28 Both channels operating 24 Calculated as Pd = VCC × ICC – 2·PO Power dissipation, Pd — W 32 VCC=18V 20 VCC=15V 16 12 VCC=12V 8 4 0 3 3 5 7 1.0 2 3 5 7 10 2 3 5 2 3 5 Output power, PO — W Power supply ripple voltage, VCCR — V rms Power dissipation, Pd — W 5 7 100k -40 -100 10 26 Power dissipation, Pd — W Ripple rejection ratio, SVRR — dB -20 2 3 VCC=15V RL=4Ω Rg=0 VCCR=0dBm Supply voltage, VCC — V 0 5 7 10k SVRR - f R 0 RL=4Ω Rg=0 fR=100Hz VCCR=0dBm Ripple rejection ratio, SVRR — dB Ripple rejection ratio, SVRR — dB 0 2 3 Input resistance, Rg — Ω Input frequency, f — Hz 24 Pd - PO (RL=8Ω) f=1kHz RL=8Ω Both channels operating Calculated as Pd = VCC × ICC – 2·PO 20 VCC=18V 16 VCC=15V 12 VCC=12V 8 4 5 7 0.1 2 3 5 7 1.0 2 3 5 7 10 Output power, PO — W 2 3 5 0 3 5 7 0.1 2 3 5 7 1.0 2 3 5 7 10 Output power, PO — W No. 5905-9/10 LA4663 220 200 R RL L =4Ω =6 =8 Ω Ω 4 3 RL Current drain, ICC — A 5 I CC - PO VCC=15V Rg=600Ω Both channels operating f=1kHz Quiescent current, ICCO — mA 6 2 1 180 I CCO - Ta RL=Open Rg=0 VCC=15V 160 140 120 100 80 60 40 0 3 5 7 0.1 2 3 5 7 1.0 2 3 5 7 10 2 20 -60 3 -40 Output power, PO — W PO - Ta Output power, PO — W 24 20 16 12 8 VCC=15V RL=4Ω THD=10% Rg=600Ω f=1kHz 4 Both channels operating With a 3°C/W heat sink 0 -60 -40 -20 0 20 40 0 20 40 60 80 100 80 100 THD - Ta 2 Total harmonic distortion, THD — % 28 -20 Ambient temperature, Ta — °C 60 Ambient temperature, Ta — °C 80 100 1.0 7 5 f =10kHz 3 2 0.1 7 5 3 2 f =1kHz VCC=15V RL=4Ω Rg=600Ω f=1kHz PO=1W Both channels operating 0.01 -60 -40 -20 0 20 40 60 Ambient temperature, Ta — °C Specifications of any and all SANYO products described or contained herein stipulate the performance, characteristics, and functions of the described products in the independent state, and are not guarantees of the performance, characteristics, and functions of the described products as mounted in the customer’s products or equipment. To verify symptoms and states that cannot be evaluated in an independent device, the customer should always evaluate and test devices mounted in the customer’s products or equipment. SANYO Electric Co., Ltd. strives to supply high-quality high-reliability products. However, any and all semiconductor products fail with some probability. It is possible that these probabilistic failures could give rise to accidents or events that could endanger human lives, that could give rise to smoke or fire, or that could cause damage to other property. When designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective circuits and error prevention circuits for safe design, redundant design, and structural design. In the event that any or all SANYO products (including technical data, services) described or contained herein are controlled under any of applicable local export control laws and regulations, such products must not be exported without obtaining the export license from the authorities concerned in accordance with the above law. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise, without the prior written permission of SANYO Electric Co., Ltd. Any and all information described or contained herein are subject to change without notice due to product/technology improvement, etc. When designing equipment, refer to the “Delivery Specification” for the SANYO product that you intend to use. Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed for volume production. SANYO believes information herein is accurate and reliable, but no guarantees are made or implied regarding its use or any infringements of intellectual property rights or other rights of third parties. This catalog provides information as of April, 2000. Specifications and information herein are subject to change without notice. PS No. 5905-10/10