Ordering number: EN5376 Monolithic Linear IC LA5314 Variable Divided Voltage Generator for LCD Use Overview Package Dimensions unit : mm The LA5314 is a valiable diveded voltage generator IC for multiple drive of LCD matrix. 3222-HSOP28 [LA5314] Features . Power supply for variable bias LCD matrix. (1/5 to 1/20 bias by built-in resistances) . available Five operational amplifiers to deliver 5 voltage outputs . Low current drain (1.6 mA typ) . Miniflat package for miniturization SANYO : HSOP28 Specifications Maximum Ratings at Ta = 25 °C Parameter Symbol Conditions Maximum supply voltage VCC max VCC – VEE Maximum output current lOUT max V0 to V4 Allowable power dissipation Ratings 38 Pd max Unit V *±25 mA 600 mW Operating temperature Topr –20 to +75 °C Storage temperature Tstg –30 to +150 °C Note: 1. Continuous operation (non breakdown) is guaranteed when operated at the maximum ratings shown above. 2. *The maximum output current is a value specified under the conditions otherwise specified separately. Operating Conditions at Ta = 25°C Parameter Symbol Conditions Ratings Unit Supply voltage VCC lOUT0, 1 V0, V1 –0.5 to +10 Output current lOUT2, 3 V2, V3 –10 to +10 mA V4 –15 to +0.5 mA lOUT4 VCC – VEE 10 to 35 V mA Note: 3. Set VCC and VEE so that |V0–V1| and |V4| become 1V or greater. SANYO Electric Co.,Ltd. Semiconductor Bussiness Headquarters TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110 JAPAN 83096HA(II) No.5376-1/5 LA5314 Operating Chararcteristics at Ta = 25°C, VCC – VEE = 20 V, VREF = VCC, RX = 8R Parameter Current drain Output voltage difference 1 Output voltage difference 2 Output voltage ratio 1 Output voltage ratio 2 Output voltage ratio 3 Output voltage ratio 4 Internal resistnace ratio 1 Internal resistance ratio 2 Internal resistance ratio 3 Internal resistance ratio 4 Symbol ICC, IEE Vd1 Vd2 Rb1 Rb2 Rb3 Rb4 8R 12R 14R 15R Resistance Load Load Load Load Load regulation regulation regulation regulation regulation R 1 2 3 4 5 ∆V0 ∆V1 ∆V2 ∆V3 ∆V4 Conditions VCC, VEE:VCC – VEE = 20 V, RX = 8R (V0 – V1) – (V1 – V2) (V3 – V4) – (V4 – VEE) V0/(V0 – V1) V0/(V0 – V2) V0/V3 V0/V4 RX1 – RX2* RX1 – RX3* RX1 – RX4* RX1 – VIN3* R value when 0.6 V is applied across RX5 – RX6 : RX5 – RX6 V0: –0.2 mA < IOUT0 < +10.0 mA V1: –0.2 mA < IOUT1 < +10.0 mA V2: –10.0 mA < IOUT2 < +10.0 mA V3: –10.0 mA < IOUT3 < +10.0 mA V4: –10.0 mA < IOUT4 < +0.2 mA min –30 –30 11.64 5.82 5.82 11.64 typ 1.6 12.00 6.00 6.00 12.00 8 12 14 15 max 3 +30 +30 12.36 6.18 6.18 12.36 20 –20 –20 –20 –20 –20 Unit mA mV mV — — — — — — — — kΩ +20 +20 +20 +20 +20 mV mV mV mV mV Allowable power dissipation, Pd max — W Note* : Referenced to R between RX4 and VIN3 Pd max — Ta Temperature, Ta — °C Pin Assignment T00025 No.5376-2/5 LA5314 Block Diagram Note: Use the IC so that VRX1 ^ VRX2 ^ VRX3 ^ VRX4 is obeyed. No.5376-3/5 LA5314 Maximum Output Current Load Test Conditions Input 1 Input 2 VCC – VEE = 20 V, RX = 8R C1 = 5 µF, C2 = 10 µF, C3 = 10 µF, C4 = 5 µF, C5 = 10 µF, C6 = 33 µF TR1 to TR5: 2SA984 E or F rank TR6 to TR11: 2SC2274 E or F rank Unit (resistance: Ω, capacitance: F) Output load resistances R1 to R10 are set in order that current of 30 mA max. are supplied to both source and sink sides when an on-level input is applied to the inputs 1 or 2. Input 1 Input 2 No.5376-4/5 LA5314 VOUT – IOUT (Source side) Output current, IOUT – mA Output voltage ratio – Ta Output voltage ratio, Rb2, Rb3 Output current, IOUT – mA Output voltage difference , Vd1, Vd2 — mV Output voltage , VOUT – V Supply voltage, VCC – V VOUT – IOUT (Sink side) Output voltage ratio, Rb1, Rb4 Current drain, ICC – mA Output voltage, VOUT – V ICC – VCC Ambient temperature, Ta – °C No products described or contained herein are intended for use in surgical implants, life-support systems, aerospace equipment, nuclear power control systems, vehicles, disaster/crime-prevention equipment and the like, the failure of which may directly or indirectly cause injury, death or property loss. Anyone purchasing any products described or contained herein for an above-mentioned use shall: 1 Accept full responsibility and indemnify and defend SANYO ELECTRIC CO., LTD., its affiliates, subsidiaries and distributors and all their officers and employees, jointly and severally, against any and all claims and litigation and all damages, cost and expenses associated with such use: 2 Not impose any responsibility for any fault or negligence which may be cited in any such claim or litigation on SANYO ELECTRIC CO., LTD., its affiliates, subsidiaries and distributors or any of their officers and employees jointly or severally. Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed for volume production. SANYO believes information herein is accurate and reliable, but no guarantees are made or implied regarding its use or any infringements of intellectual property rights or other rights of third parties. This catalog provides information as of August, 1996. Specifications and information herein are subject to change without notice. No.5376-5/5