SANYO LC75808

Ordering number : ENN6370A
CMOS IC
LC75808E, 75808W
1/8 to 1/10 Duty LCD Display Drivers
with Key Input Function
Overview
Package Dimensions
The LC75808E and LC75808W are 1/8 to 1/10 duty LCD
display drivers that can directly drive up to 600 segments
and can control up to four general-purpose output ports.
These products also incorporate a key scan circuit that
accepts input from up to 30 keys to reduce printed circuit
board wiring.
unit: mm
3151-QFP100E
0.825
[LC75808E]
23.2
20.0
0.3
0.65
0.575
1.6
0.575
0.15
80
81
51
50
15.6
0.825
31
1.6
30
21.6
0.1
0.8
1
3.0max
100
2.7
0.8
SANYO: QFP100E
unit: mm
3181B-SQFP100
[LC75808W]
16.0
14.0
1.0
0.5
1.0
1.0
75
0.145
51
50
76
0.5
16.0
14.0
1
0.2
25
0.5
1.6max
26
100
1.0
• Key input function for up to 30 keys (A key scan is
performed only when a key is pressed.)
• 1/8duty–1/4bias, 1/9duty–1/4bias, and 1/10duty–1/4bias
drive schemes can be controlled from serial data.
1/8duty–1/4bias: up to 480 segments
1/9duty–1/4bias: up to 540 segments
1/10duty–1/4bias: up to 600 segments
• Sleep mode and all segments off functions that are
controlled from serial data.
• Serial data I/O supports CCB format communication
with the system controller.
• Direct display of display data without the use of a
decoder provides high generality.
• Built-in display contrast adjustment circuit.
• Up to 4 general-purpose output ports are included.
• Independent LCD driver block power supply VLCD.
• Provision of an on-chip voltage-detection type reset
circuit prevents incorrect displays.
• The INH pin is provided. This pin turns off the display,
disables key scanning, and forces the general-purpose
output ports to the low level.
• RC oscillator circuit.
17.2
14.0
0.65
Features
1.4
0.1
0.5
SANYO: SQFP100
• CCB is a trademark of SANYO ELECTRIC CO., LTD.
• CCB is SANYO’s original bus format and all the bus
addresses are controlled by SANYO.
Any and all SANYO products described or contained herein do not have specifications that can handle
applications that require extremely high levels of reliability, such as life-support systems, aircraft’s
control systems, or other applications whose failure can be reasonably expected to result in serious
physical and/or material damage. Consult with your SANYO representative nearest you before using
any SANYO products described or contained herein in such applications.
SANYO assumes no responsibility for equipment failures that result from using products at values that
exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other
parameters) listed in products specifications of any and all SANYO products described or contained
herein.
SANYO Electric Co.,Ltd. Semiconductor Company
TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110-8534 JAPAN
31000RM (OT)/12800RM No. 6370 -1/39
LC75808E, 75808W
Pin Assignment
No. 6370 -2/39
LC75808E, 75808W
Specifications
Absolute Maximum Ratings at Ta=25°C, VSS=0V
Parameter
Maximum supply voltage
Input voltage
Output voltage
Output current
Allowable power dissipation
Symbol
Conditions
Ratings
Unit
VDD max
VDD
–0.3 to +7.0
VLCD max
VLCD
–0.3 to +12.0
VIN1
CE, CL, DI, INH
VIN2
OSC, KI1 to KI5, TEST
VIN3
VLCD1, VLCD2, VLCD3, VLCD4
–0.3 to +7.0
–0.3 to VDD +0.3
V
–0.3 to VLCD +0.3
VOUT1
DO
VOUT2
OSC, KS1 to KS6, P1 to P4
VOUT3
VLCD0, S1 to S60, COM1 to COM10
IOUT1
S1 to S60
IOUT2
COM1 to COM10
IOUT3
KS1 to KS6
1
IOUT4
P1 to P4
5
Pd max
V
–0.3 to +7.0
–0.3 to VDD +0.3
V
–0.3 to VLCD +0.3
300
µA
3
Ta = 85°C
200
mA
mW
Operating temperature
Topr
–40 to +85
°C
Storage temperature
Tstg
–55 to +125
°C
Allowable Operating Ranges at Ta = –40 to +85°C, VSS=0V
Parameter
Symbol
VDD
Supply voltage
Output voltage
Input voltage
Input high level voltage
Input low level voltage
VLCD
VLCD0
Ratings
Conditions
min
typ
max
VDD
4.5
6.0
VLCD, When the display contrast adjustment
circuit is used
7.0
11.0
VLCD, When the display contrast adjustment
circuit is not used
4.5
11.0
VLCD0
V
VLCD4 + 4.5
VLCD
VLCD1
VLCD1
3/4
(VLCD0–VLCD4)
VLCD2
VLCD2
2/4
(VLCD0–VLCD4)
VLCD0
VLCD3
VLCD3
1/4
(VLCD0–VLCD4)
VLCD0
VLCD4
VLCD4
VLCD0
0
1.5
VIH1
CE, CL, DI, INH
0.8 VDD
6.0
VIH2
KI1 to KI5
0.6 VDD
VDD
VIL
CE, CL, DI, INH, KI1 to KI5
Recommended external resistance
ROSC
OSC
Recommended external capacitance
COSC
OSC
Guaranteed oscillation range
fOSC
OSC
Unit
0
0.2 VDD
43
50
V
V
V
kΩ
680
25
V
pF
100
kHz
Data setup time
tds
CL, DI
:Figure 2
160
Data hold time
tdh
CL, DI
:Figure 2
160
ns
ns
CE wait time
tcp
CE, CL
:Figure 2
160
ns
CE setup time
tcs
CE, CL
:Figure 2
160
ns
CE hold time
tch
CE, CL
:Figure 2
160
ns
High level clock pulse width
tøH
CL
:Figure 2
160
ns
Low level clock pulse width
tøL
CL
:Figure 2
160
DO output delay time
tdc
DO, RPU = 4.7 kΩ, CL = 10 pF *1 :Figure 2
1.5
µs
DO rise time
tdr
DO, RPU = 4.7 kΩ, CL = 10 pF *1 :Figure 2
1.5
µs
ns
Note: *1. Since DO is an open-drain output, these values depend on the resistance of the pull-up resistor RPU and the load capacitance CL.
No. 6370 -3/39
LC75808E, 75808W
Electrical Characteristics for the Allowable Operating Ranges
Parameter
Hysteresis
Power-down detection voltage
Symbol
VH
Conditions
Input low level current
IIL
CE, CL, DI, INH: VI = 0 V
Input floating voltage
VIF
KI1 to KI5
Pull-down resistance
RPD
KI1 to KI5: VDD = 5.0 V
Output high level voltage
Output low level voltage
Output middle level voltage *2
Oscillator frequency
Current drain
IOFFH
DO: VO = 6.0 V
VOH1
S1 to S60: IO = –20 µA
Unit
max
0.1 VDD
2.5
CE, CL, DI, INH: VI = 6.0 V
Output off leakage current
typ
CE, CL, DI, INH, KI1 to KI5
VDET
IIH
Input high level current
Ratings
min
3.0
V
3.5
V
5.0
µA
–5.0
µA
0.05 VDD
50
100
kΩ
6.0
µA
VLCD0 – 0.6
VOH2
COM1 to COM10: IO = –100 µA
VLCD0 – 0.6
VOH3
KS1 to KS6: IO = –500 µA
VDD – 1.0
VOH4
P1 to P4: IO = –1 mA
VDD – 1.0
VOL1
S1 to S60: IO = 20 µA
VOL2
COM1 to COM10: IO = 100 µA
VOL3
KS1 to KS6: IO = 25 µA
VOL4
P1 to P4: IO = 1 mA
VOL5
DO: IO = 1mA
VDD – 0.5
VDD – 0.2
VLCD4 + 0.6
0.2
0.5
1.5
0.1
0.5
S1 to S60: IO = ±20 µA
VMID2
COM1 to COM10: IO = ±100 µA
3/4
(VLCD0 – VLCD4)
–0.6
3/4
(VLCD0 – VLCD4)
+0.6
VMID3
COM1 to COM10: IO = ±100 µA
1/4
(VLCD0 – VLCD4)
–0.6
1/4
(VLCD0 – VLCD4)
+0.6
OSC: ROSC = 43 kΩ, COSC = 680 pF
VDD :Sleep mode
V
1.0
VMID1
fosc
V
VLCD4 + 0.6
2/4
(VLCD0 – VLCD4)
–0.6
IDD1
V
250
40
50
2/4
(VLCD0 – VLCD4)
+0.6
60
V
kHz
100
IDD2
VDD: VDD = 6.0 V, outputs open,fosc = 50 kHz
ILCD1
VLCD : Sleep mode
250
500
ILCD2
VLCD : VLCD = 11.0 V
Outputs open
fosc = 50 kHz
(When the display contrast adjustment circuit is used.)
500
1000
ILCD3
VLCD : VLCD = 11.0 V
Outputs open
fosc = 50 kHz
(When the display contrast adjustment circuit is not
used.)
250
500
5
µA
Note: *2. Excluding the bias voltage generation divider resistor built into VLCD0, VLCD1, VLCD2 , VLCD3, and VLCD4. (See Figure 1.)
No. 6370 -4/39
LC75808E, 75808W
To the common and segment drivers
Excluding these resistors.
Figure 1
1. When CL is stopped at the low level
2. When CL is stopped at the high level
Figure 2
No. 6370 -5/39
LC75808E, 75808W
Block Diagram
No. 6370 -6/39
LC75808E, 75808W
Pin Functions
Pin
Pin No.
LC75808E
Function
LC75808W
Active
I/O
Handling
when unused
S1 to S60
3 to 62
1 to 60
Segment driver outputs.
—
●
OPEN
COM1 to COM10
72 to 63
70 to 61
Common driver outputs.
—
●
OPEN
—
O
OPEN
KS1 to KS6
73 to 78
71 to 76
Key scan outputs.
Although normal key scan timing lines require diodes to be inserted in
the timing lines to prevent shorts, since these outputs are unbalanced
CMOS transistor outputs, these outputs will not be damaged by shorting
when these outputs are used to form a key matrix.
KI1 to KI5
79 to 83
77 to 81
Key scan inputs.
These pins have built-in pull-down resistors.
H
I
GND
P1 to P4
84 to 87
82 to 85
General-purpose output ports.
—
●
OPEN
Oscillator connection.
An oscillator circuit is formed by connecting an external resistor and
capacitor at this pin.
—
I/O
VDD
H
I
▲
I
—
I
—
O
OPEN
L
I
VDD
OSC
97
95
CE
100
98
CL
1
99
DI
2
100
DO
99
97
Serial data interface connections to the controller. Note that DO, being
an open-drain output, requires a pull-up resistor.
CE :Chip enable
CL :Synchronization clock
DI :Transfer data
DO :Output data
GND
INH
98
96
Input that turns the display off, disables key scanning, and forces the
general-purpose output ports low.
• When INH is low (VSS):
• Display off
S1 to S60 = “L” (VLCD4).
COM1 to COM10 = “L” (VLCD4).
• General-purpose output ports P1 to P4 = low (VSS)
• Key scanning is disabled: KS1 to KS6 = low (VSS)
• All the key data is reset to low.
• When INH is high (VDD):
• Display on
• The states of the general-purpose output ports can be set by
the PC1 to PC4 control data.
• Key scanning is enabled.
However, serial data can be transferred when the INH pin is low.
TEST
96
94
This pin must be connected to ground.
—
I
—
—
0
OPEN
VLCD0
90
88
LCD drive 4/4 bias voltage (high level) supply pin. The level on this pin
can be changed by the display contrast adjustment circuit.
However, (VLCD0 – VLCD4) must be greater than or equal to 4.5 V.
Also,external power must not be applied to this pin since the pin circuit
includes the display contrast adjustment circuit.
VLCD1
91
89
LCD drive 3/4 bias voltage (middle level) supply pin. This pin can be
used to supply the 3/4 (VLCD0 – VLCD4) voltage level externally.
—
I
OPEN
VLCD2
92
90
LCD drive 2/4 bias voltage (middle level) supply pin. This pin can be
used to supply the 2/4 (VLCD0 – VLCD4) voltage level externally.
—
I
OPEN
VLCD3
93
91
LCD drive 1/4 bias voltage (middle level) supply pin. This pin can be
used to supply the 1/4 (VLCD0 – VLCD4) voltage level externally.
—
I
OPEN
—
I
GND
VLCD4
94
92
LCD drive 0/4 bias voltage (low level) supply pin. Fine adjustment of the
display contrast can be implemented by connecting an external variable
resistor to this pin.
However, (VLCD0 – VLCD4) must be greater than or equal to 4.5 V, and
VLCD4 must be in the range 0 V to 1.5 V, inclusive.
VDD
88
86
Logic block power supply connection. Provide a voltage of between 4.5
and 6.0V.
—
—
—
VLCD
89
87
LCD driver block power supply connection. Provide a voltage of between
7.0 and 11.0 V when the display contrast adjustment circuit is used and
provide a voltage of between 4.5 and 11.0 V when the circuit is not used.
—
—
—
VSS
95
93
Power supply connection. Connect to ground.
—
—
—
No. 6370 -7/39
LC75808E, 75808W
Serial Data Input
1. 1/8 duty
① When CL is stopped at the low level.
• When the display data is transferred.
Display data
Fixed data
Display data
Fixed data
Display data
Fixed data
Display data
Fixed data
• When the control data is transferred.
Control data
Note: B0 to B3,A0 to A3 ........ CCB address
DD ................................ Direction data
No. 6370 -8/39
LC75808E, 75808W
② When CL is stopped at the high level.
• When the display data is transferred.
Display data
Fixed data
Display data
Fixed data
Display data
Fixed data
Display data
Fixed data
• When the control data is transferred.
Control data
Note: B0 to B3,A0 to A3 ........ CCB address
DD ................................ Direction data
• CCB address: ....42H
• D1 to D480: ........ Display data
• KC1 to KC6: ........ Key scan output state setting data
• PC1 to PC4: ........ General-purpose output port state setting data
• CT0 to CT3, CTC: Display contrast setting data
• SC: ...................... Segment on/off control data
• SP: ...................... Normal mode/sleep mode control data
• DT1, DT2: ............ Display technique setting data
No. 6370 -9/39
LC75808E, 75808W
2. 1/9 duty
① When CL is stopped at the low level.
• When the display data is transferred.
Display data
Fixed data
Display data
Fixed data
Display data
Fixed data
Display data
Fixed data
• When the control data is transferred.
Control data
Note: B0 to B3,A0 to A3 ........ CCB address
DD ................................ Direction data
No. 6370 -10/39
LC75808E, 75808W
② When CL is stopped at the high level.
• When the display data is transferred.
Display data
Fixed data
Display data
Fixed data
Display data
Fixed data
Display data
Fixed data
• When the control data is transferred.
Control data
Note: B0 to B3,A0 to A3 ........ CCB address
DD ................................ Direction data
• CCB address: ...... 42H
• D1 to D540: ........ Display data
• KC1 to KC6: ........ Key scan output state setting data
• PC1 to PC4: ........ General-purpose output port state setting data
• CT0 to CT3, CTC: Display contrast setting data
• SC: ...................... Segment on/off control data
• SP: ...................... Normal mode/sleep mode control data
• DT1, DT2: ............ Display technique setting data
No. 6370 -11/39
LC75808E, 75808W
3. 1/10 duty
① When CL is stopped at the low level.
• When the display data is transferred.
Display data
Fixed data
Display data
Fixed data
Display data
Fixed data
Display data
Fixed data
• When the control data is transferred.
Control data
Note: B0 to B3,A0 to A3 ........ CCB address
DD ................................ Direction data
No. 6370 -12/39
LC75808E, 75808W
② When CL is stopped at the high level.
• When the display data is transferred.
Display data
Fixed data
Display data
Fixed data
Display data
Fixed data
Display data
Fixed data
• When the control data is transferred.
Control data
Note: B0 to B3,A0 to A3 ........ CCB address
DD ................................ Direction data
• CCB address: ...... 42H
• D1 to D600: ........ Display data
• KC1 to KC6: ........ Key scan output state setting data
• PC1 to PC4: ........ General-purpose output port state setting data
• CT0 to CT3, CTC: Display contrast setting data
• SC: ...................... Segment on/off control data
• SP: ...................... Normal mode/sleep mode control data
• DT1, DT2: ............ Display technique setting data
No. 6370 -13/39
LC75808E, 75808W
Control Data Functions
1. KC1 to KC6: Key scan output state setting data
These control data bits set the states of the key scan output pins KS1 to KS6.
Output pin
KS1
KS2
KS3
KS4
KS5
KS6
Key scan output state setting data
KC1
KC2
KC3
KC4
KC5
KC6
For example, if KC1 to KC3 are set to 1, and KC4 to KC6 are set to 0, then the output pins KS1 to KS3 will output high
levels (VDD) and the output pins KS4 to KS6 will output low levels (VSS) in the key scan standby state.
Note that key scan output signal is not output from output pins that are set low.
2. PC1 to PC4: General-purpose output port state setting data
These control data bits set the states of the general-purpose output ports P1 to P4.
Output pin
P1
P2
P3
P4
General-purpose output port state setting data
PC1
PC2
PC3
PC4
For example, if PC1 and PC2 are set to 1, and PC3 and PC4 are set to 0, then the output pins P1 and P2 will output high
levels (VDD) and the output pins P3 and P4 will output low levels (VSS).
3. CT0 to CT3, CTC: Display contrast setting data
These control data bits set the display contrast.
CT0 to CT3: Display contrast setting (11 steps)
CT0
CT1
CT2
CT3
0
0
0
0
LCD drive 4/4 bias voltage supply VLCD0 level
0.94 VLCD = VLCD – (0.03 VLCD × 2)
1
0
0
0
0.91 VLCD = VLCD – (0.03 VLCD × 3)
0
1
0
0
0.88 VLCD = VLCD – (0.03 VLCD × 4)
1
1
0
0
0.85 VLCD = VLCD – (0.03 VLCD × 5)
0
0
1
0
0.82 VLCD = VLCD – (0.03 VLCD × 6)
1
0
1
0
0.79 VLCD = VLCD – (0.03 VLCD × 7)
0
1
1
0
0.76 VLCD = VLCD – (0.03 VLCD × 8)
1
1
1
0
0.73 VLCD = VLCD – (0.03 VLCD × 9)
0
0
0
1
0.70 VLCD = VLCD – (0.03 VLCD × 10)
1
0
0
1
0.67 VLCD = VLCD – (0.03 VLCD × 11)
0
1
0
1
0.64 VLCD = VLCD – (0.03 VLCD × 12)
CTC: Display contrast adjustment circuit state setting
CTC
Display contrast adjustment circuit state
0
The display contrast adjustment circuit is disabled, and the VLCD0 pin level is forced to the VLCD level.
1
The display contrast adjustment circuit operates, and the display contrast is adjusted.
Note that although the display contrast can be adjusted by operating the built-in display contrast adjustment circuit, it is
also possible to apply fine adjustments to the contrast by connecting an external variable resistor to the VLCD4 pin and
modifying the VLCD4 pin voltage. However, the following conditions must be met: (VLCD0 – VLCD4) ≥ 4.5 V, and 1.5 V
≥ VLCD4 ≥ 0 V.
No. 6370 -14/39
LC75808E, 75808W
4. SC: Segment on/off control data
This control data bit controls the on/off state of the segments.
SC
Display state
0
On
1
Off
However, note that when the segments are turned off by setting SC to 1, the segments are turned off by outputting segment off waveforms from the segment
output pins.
5. SP: Normal mode/sleep mode control data
This control data bit controls the normal mode and sleep mode.
SP
Mode
0
Normal mode
Sleep mode
The common and segment pins go to the VLCD4 level and the oscillator on the OSC pin is stopped (although it operates during key
scan operations) to reduce current drain. Note that the states of the general-purpose output ports P1 to P4 are set by PC1 to PC4 in
the control data during sleep mode as well as normal mode.
1
6. DT1, DT2: Display technique setting data
These control data bits set the display technique.
DT1
DT2
Output pins
Display technique
COM9
COM10
1/8 duty 1/4 bias drive
Fixed at the VLCD4 level
Fixed at the VLCD4 level
0
0
1
0
1/9 duty 1/4 bias drive
COM9
Fixed at the VLCD4 level
0
1
1/10 duty 1/4 bias drive
COM9
COM10
Note: COMn (n = 9 or 10): Common outputs
No. 6370 -15/39
LC75808E, 75808W
Display Data and Output Pin Correspondence
1. 1/8 duty
Output Pin
COM1
COM2
COM3
COM4
COM5
COM6
COM7
S1
D1
D2
D3
D4
D5
D6
D7
COM8
D8
S2
D9
D10
D11
D12
D13
D14
D15
D16
S3
D17
D18
D19
D20
D21
D22
D23
D24
S4
D25
D26
D27
D28
D29
D30
D31
D32
S5
D33
D34
D35
D36
D37
D38
D39
D40
S6
D41
D42
D43
D44
D45
D46
D47
D48
S7
D49
D50
D51
D52
D53
D54
D55
D56
S8
D57
D58
D59
D60
D61
D62
D63
D64
S9
D65
D66
D67
D68
D69
D70
D71
D72
S10
D73
D74
D75
D76
D77
D78
D79
D80
S11
D81
D82
D83
D84
D85
D86
D87
D88
S12
D89
D90
D91
D92
D93
D94
D95
D96
S13
D97
D98
D99
D100
D101
D102
D103
D104
S14
D105
D106
D107
D108
D109
D110
D111
D112
S15
D113
D114
D115
D116
D117
D118
D119
D120
S16
D121
D122
D123
D124
D125
D126
D127
D128
S17
D129
D130
D131
D132
D133
D134
D135
D136
S18
D137
D138
D139
D140
D141
D142
D143
D144
S19
D145
D146
D147
D148
D149
D150
D151
D152
S20
D153
D154
D155
D156
D157
D158
D159
D160
S21
D161
D162
D163
D164
D165
D166
D167
D168
S22
D169
D170
D171
D172
D173
D174
D175
D176
S23
D177
D178
D179
D180
D181
D182
D183
D184
S24
D185
D186
D187
D188
D189
D190
D191
D192
S25
D193
D194
D195
D196
D197
D198
D199
D200
S26
D201
D202
D203
D204
D205
D206
D207
D208
S27
D209
D210
D211
D212
D213
D214
D215
D216
S28
D217
D218
D219
D220
D221
D222
D223
D224
S29
D225
D226
D227
D228
D229
D230
D231
D232
S30
D233
D234
D235
D236
D237
D238
D239
D240
S31
D241
D242
D243
D244
D245
D246
D247
D248
S32
D249
D250
D251
D252
D253
D254
D255
D256
S33
D257
D258
D259
D260
D261
D262
D263
D264
S34
D265
D266
D267
D268
D269
D270
D271
D272
S35
D273
D274
D275
D276
D277
D278
D279
D280
S36
D281
D282
D283
D284
D285
D286
D287
D288
S37
D289
D290
D291
D292
D293
D294
D295
D296
S38
D297
D298
D299
D300
D301
D302
D303
D304
S39
D305
D306
D307
D308
D309
D310
D311
D312
S40
D313
D314
D315
D316
D317
D318
D319
D320
S41
D321
D322
D323
D324
D325
D326
D327
D328
S42
D329
D330
D331
D332
D333
D334
D335
D336
S43
D337
D338
D339
D340
D341
D342
D343
D344
S44
D345
D346
D347
D348
D349
D350
D351
D352
S45
D353
D354
D355
D356
D357
D358
D359
D360
Continued on next page.
No. 6370 -16/39
LC75808E, 75808W
Continued from preceding page.
Output Pin
COM1
COM2
COM3
COM4
COM5
COM6
COM7
COM8
S46
D361
D362
D363
D364
D365
D366
D367
D368
S47
D369
D370
D371
D372
D373
D374
D375
D376
S48
D377
D378
D379
D380
D381
D382
D383
D384
S49
D385
D386
D387
D388
D389
D390
D391
D392
S50
D393
D394
D395
D396
D397
D398
D399
D400
S51
D401
D402
D403
D404
D405
D406
D407
D408
S52
D409
D410
D411
D412
D413
D414
D415
D416
S53
D417
D418
D419
D420
D421
D422
D423
D424
S54
D425
D426
D427
D428
D429
D430
D431
D432
S55
D433
D434
D435
D436
D437
D438
D439
D440
S56
D441
D442
D443
D444
D445
D446
D447
D448
S57
D449
D450
D451
D452
D453
D454
D455
D456
S58
D457
D458
D459
D460
D461
D462
D463
D464
S59
D465
D466
D467
D468
D469
D470
D471
D472
S60
D473
D474
D475
D476
D477
D478
D479
D480
For example, the table below lists the segment output states for the S11 output pin.
Display data
Output pin state (S11)
D81
D82
D83
D84
D85
D86
D87
D88
0
0
0
0
0
0
0
0
The LCD segments for COM1 to COM8 are off.
1
0
0
0
0
0
0
0
The LCD segment for COM1 is on.
0
1
0
0
0
0
0
0
The LCD segment for COM2 is on.
0
0
1
0
0
0
0
0
The LCD segment for COM3 is on.
0
0
0
1
0
0
0
0
The LCD segment for COM4 is on.
0
0
0
0
1
0
0
0
The LCD segment for COM5 is on.
0
0
0
0
0
1
0
0
The LCD segment for COM6 is on.
0
0
0
0
0
0
1
0
The LCD segment for COM7 is on.
0
0
0
0
0
0
0
1
The LCD segment for COM8 is on.
1
1
1
1
1
1
1
1
The LCD segments for COM1 to COM8 are on.
No. 6370 -17/39
LC75808E, 75808W
2. 1/9 duty
Output Pin
COM1
COM2
COM3
COM4
COM5
COM6
COM7
COM8
S1
D1
D2
D3
D4
D5
D6
D7
D8
COM9
D9
S2
D10
D11
D12
D13
D14
D15
D16
D17
D18
S3
D19
D20
D21
D22
D23
D24
D25
D26
D27
S4
D28
D29
D30
D31
D32
D33
D34
D35
D36
S5
D37
D38
D39
D40
D41
D42
D43
D44
D45
S6
D46
D47
D48
D49
D50
D51
D52
D53
D54
S7
D55
D56
D57
D58
D59
D60
D61
D62
D63
S8
D64
D65
D66
D67
D68
D69
D70
D71
D72
S9
D73
D74
D75
D76
D77
D78
D79
D80
D81
S10
D82
D83
D84
D85
D86
D87
D88
D89
D90
S11
D91
D92
D93
D94
D95
D96
D97
D98
D99
S12
D100
D101
D102
D103
D104
D105
D106
D107
D108
S13
D109
D110
D111
D112
D113
D114
D115
D116
D117
S14
D118
D119
D120
D121
D122
D123
D124
D125
D126
S15
D127
D128
D129
D130
D131
D132
D133
D134
D135
S16
D136
D137
D138
D139
D140
D141
D142
D143
D144
S17
D145
D146
D147
D148
D149
D150
D151
D152
D153
S18
D154
D155
D156
D157
D158
D159
D160
D161
D162
S19
D163
D164
D165
D166
D167
D168
D169
D170
D171
S20
D172
D173
D174
D175
D176
D177
D178
D179
D180
S21
D181
D182
D183
D184
D185
D186
D187
D188
D189
S22
D190
D191
D192
D193
D194
D195
D196
D197
D198
S23
D199
D200
D201
D202
D203
D204
D205
D206
D207
S24
D208
D209
D210
D211
D212
D213
D214
D215
D216
S25
D217
D218
D219
D220
D221
D222
D223
D224
D225
S26
D226
D227
D228
D229
D230
D231
D232
D233
D234
S27
D235
D236
D237
D238
D239
D240
D241
D242
D243
S28
D244
D245
D246
D247
D248
D249
D250
D251
D252
S29
D253
D254
D255
D256
D257
D258
D259
D260
D261
S30
D262
D263
D264
D265
D266
D267
D268
D269
D270
S31
D271
D272
D273
D274
D275
D276
D277
D278
D279
S32
D280
D281
D282
D283
D284
D285
D286
D287
D288
S33
D289
D290
D291
D292
D293
D294
D295
D296
D297
S34
D298
D299
D300
D301
D302
D303
D304
D305
D306
S35
D307
D308
D309
D310
D311
D312
D313
D314
D315
S36
D316
D317
D318
D319
D320
D321
D322
D323
D324
S37
D325
D326
D327
D328
D329
D330
D331
D332
D333
S38
D334
D335
D336
D337
D338
D339
D340
D341
D342
S39
D343
D344
D345
D346
D347
D348
D349
D350
D351
S40
D352
D353
D354
D355
D356
D357
D358
D359
D360
S41
D361
D362
D363
D364
D365
D366
D367
D368
D369
S42
D370
D371
D372
D373
D374
D375
D376
D377
D378
S43
D379
D380
D381
D382
D383
D384
D385
D386
D387
S44
D388
D389
D390
D391
D392
D393
D394
D395
D396
S45
D397
D398
D399
D400
D401
D402
D403
D404
D405
Continued on next page.
No. 6370 -18/39
LC75808E, 75808W
Continued from preceding page.
Output Pin
COM1
COM2
COM3
COM4
COM5
COM6
COM7
COM8
COM9
S46
D406
D407
D408
D409
D410
D411
D412
D413
D414
S47
D415
D416
D417
D418
D419
D420
D421
D422
D423
S48
D424
D425
D426
D427
D428
D429
D430
D431
D432
S49
D433
D434
D435
D436
D437
D438
D439
D440
D441
S50
D442
D443
D444
D445
D446
D447
D448
D449
D450
S51
D451
D452
D453
D454
D455
D456
D457
D458
D459
S52
D460
D461
D462
D463
D464
D465
D466
D467
D468
S53
D469
D470
D471
D472
D473
D474
D475
D476
D477
S54
D478
D479
D480
D481
D482
D483
D484
D485
D486
S55
D487
D488
D489
D490
D491
D492
D493
D494
D495
S56
D496
D497
D498
D499
D500
D501
D502
D503
D504
S57
D505
D506
D507
D508
D509
D510
D511
D512
D513
S58
D514
D515
D516
D517
D518
D519
D520
D521
D522
S59
D523
D524
D525
D526
D527
D528
D529
D530
D531
S60
D532
D533
D534
D535
D536
D537
D538
D539
D540
For example, the table below lists the segment output states for the S11 output pin.
Display data
Output pin state (S11)
D91
D92
D93
D94
D95
D96
D97
D98
D99
0
0
0
0
0
0
0
0
0
The LCD segments for COM1 to COM9 are off.
1
0
0
0
0
0
0
0
0
The LCD segment for COM1 is on.
0
1
0
0
0
0
0
0
0
The LCD segment for COM2 is on.
0
0
1
0
0
0
0
0
0
The LCD segment for COM3 is on.
0
0
0
1
0
0
0
0
0
The LCD segment for COM4 is on.
0
0
0
0
1
0
0
0
0
The LCD segment for COM5 is on.
0
0
0
0
0
1
0
0
0
The LCD segment for COM6 is on.
0
0
0
0
0
0
1
0
0
The LCD segment for COM7 is on.
0
0
0
0
0
0
0
1
0
The LCD segment for COM8 is on.
0
0
0
0
0
0
0
0
1
The LCD segment for COM9 is on.
1
1
1
1
1
1
1
1
1
The LCD segments for COM1 to COM9 are on.
No. 6370 -19/39
LC75808E, 75808W
3. 1/10 duty
Output Pin
COM1
COM2
COM3
COM4
COM5
COM6
COM7
COM8
COM9
COM10
S1
D1
D2
D3
D4
D5
D6
D7
D8
D9
D10
S2
D11
D12
D13
D14
D15
D16
D17
D18
D19
D20
S3
D21
D22
D23
D24
D25
D26
D27
D28
D29
D30
S4
D31
D32
D33
D34
D35
D36
D37
D38
D39
D40
S5
D41
D42
D43
D44
D45
D46
D47
D48
D49
D50
S6
D51
D52
D53
D54
D55
D56
D57
D58
D59
D60
S7
D61
D62
D63
D64
D65
D66
D67
D68
D69
D70
S8
D71
D72
D73
D74
D75
D76
D77
D78
D79
D80
S9
D81
D82
D83
D84
D85
D86
D87
D88
D89
D90
S10
D91
D92
D93
D94
D95
D96
D97
D98
D99
D100
S11
D101
D102
D103
D104
D105
D106
D107
D108
D109
D110
S12
D111
D112
D113
D114
D115
D116
D117
D118
D119
D120
S13
D121
D122
D123
D124
D125
D126
D127
D128
D129
D130
S14
D131
D132
D133
D134
D135
D136
D137
D138
D139
D140
S15
D141
D142
D143
D144
D145
D146
D147
D148
D149
D150
S16
D151
D152
D153
D154
D155
D156
D157
D158
D159
D160
S17
D161
D162
D163
D164
D165
D166
D167
D168
D169
D170
S18
D171
D172
D173
D174
D175
D176
D177
D178
D179
D180
S19
D181
D182
D183
D184
D185
D186
D187
D188
D189
D190
S20
D191
D192
D193
D194
D195
D196
D197
D198
D199
D200
S21
D201
D202
D203
D204
D205
D206
D207
D208
D209
D210
S22
D211
D212
D213
D214
D215
D216
D217
D218
D219
D220
S23
D221
D222
D223
D224
D225
D226
D227
D228
D229
D230
S24
D231
D232
D233
D234
D235
D236
D237
D238
D239
D240
S25
D241
D242
D243
D244
D245
D246
D247
D248
D249
D250
S26
D251
D252
D253
D254
D255
D256
D257
D258
D259
D260
S27
D261
D262
D263
D264
D265
D266
D267
D268
D269
D270
S28
D271
D272
D273
D274
D275
D276
D277
D278
D279
D280
S29
D281
D282
D283
D284
D285
D286
D287
D288
D289
D290
S30
D291
D292
D293
D294
D295
D296
D297
D298
D299
D300
S31
D301
D302
D303
D304
D305
D306
D307
D308
D309
D310
S32
D311
D312
D313
D314
D315
D316
D317
D318
D319
D320
S33
D321
D322
D323
D324
D325
D326
D327
D328
D329
D330
S34
D331
D332
D333
D334
D335
D336
D337
D338
D339
D340
S35
D341
D342
D343
D344
D345
D346
D347
D348
D349
D350
S36
D351
D352
D353
D354
D355
D356
D357
D358
D359
D360
S37
D361
D362
D363
D364
D365
D366
D367
D368
D369
D370
S38
D371
D372
D373
D374
D375
D376
D377
D378
D379
D380
S39
D381
D382
D383
D384
D385
D386
D387
D388
D389
D390
S40
D391
D392
D393
D394
D395
D396
D397
D398
D399
D400
S41
D401
D402
D403
D404
D405
D406
D407
D408
D409
D410
S42
D411
D412
D413
D414
D415
D416
D417
D418
D419
D420
S43
D421
D422
D423
D424
D425
D426
D427
D428
D429
D430
S44
D431
D432
D433
D434
D435
D436
D437
D438
D439
D440
S45
D441
D442
D443
D444
D445
D446
D447
D448
D449
D450
Continued on next page.
No. 6370 -20/39
LC75808E, 75808W
Continued from preceding page.
Output Pin
COM1
COM2
COM3
COM4
COM5
COM6
COM7
COM8
COM9
COM10
S46
D451
D452
D453
D454
D455
D456
D457
D458
D459
D460
S47
D461
D462
D463
D464
D465
D466
D467
D468
D469
D470
S48
D471
D472
D473
D474
D475
D476
D477
D478
D479
D480
S49
D481
D482
D483
D484
D485
D486
D487
D488
D489
D490
S50
D491
D492
D493
D494
D495
D496
D497
D498
D499
D500
S51
D501
D502
D503
D504
D505
D506
D507
D508
D509
D510
S52
D511
D512
D513
D514
D515
D516
D517
D518
D519
D520
S53
D521
D522
D523
D524
D525
D526
D527
D528
D529
D530
S54
D531
D532
D533
D534
D535
D536
D537
D538
D539
D540
S55
D541
D542
D543
D544
D545
D546
D547
D548
D549
D550
S56
D551
D552
D553
D554
D555
D556
D557
D558
D559
D560
S57
D561
D562
D563
D564
D565
D566
D567
D568
D569
D570
S58
D571
D572
D573
D574
D575
D576
D577
D578
D579
D580
S59
D581
D582
D583
D584
D585
D586
D587
D588
D589
D590
S60
D591
D592
D593
D594
D595
D596
D597
D598
D599
D600
For example, the table below lists the segment output states for the S11 output pin.
Display data
Output pin state (S11)
D101
D102
D103
D104
D105
D106
D107
D108
D109
D110
0
0
0
0
0
0
0
0
0
0
The LCD segments for COM1 to COM10 are off.
1
0
0
0
0
0
0
0
0
0
The LCD segment for COM1 is on.
0
1
0
0
0
0
0
0
0
0
The LCD segment for COM2 is on.
0
0
1
0
0
0
0
0
0
0
The LCD segment for COM3 is on.
0
0
0
1
0
0
0
0
0
0
The LCD segment for COM4 is on.
0
0
0
0
1
0
0
0
0
0
The LCD segment for COM5 is on.
0
0
0
0
0
1
0
0
0
0
The LCD segment for COM6 is on.
0
0
0
0
0
0
1
0
0
0
The LCD segment for COM7 is on.
0
0
0
0
0
0
0
1
0
0
The LCD segment for COM8 is on.
0
0
0
0
0
0
0
0
1
0
The LCD segment for COM9 is on.
0
0
0
0
0
0
0
0
0
1
The LCD segment for COM10 is on.
1
1
1
1
1
1
1
1
1
1
The LCD segments for COM1 to COM10 are on.
No. 6370 -21/39
LC75808E, 75808W
Serial Data Output
1. When CL is stopped at the low level
2. When CL is stopped at the high level
Note: B0 to B3, A0 to A3······CCB address ‘43H’
KD1 to KD30 ............ Key data
SA ............................ Sleep acknowledge data
Note: If a key data read operation is executed when DO is high, the read key data (KD1 to KD30) and sleep acknowledge data(SA) will be invalid.
Output Data
1. KD1 to KD30 : Key data
When a key matrix of up to 30 keys is formed from the KS1 to KS6 output pins and the KI1 to KI5 input pins and
one of those keys is pressed, the key output data corresponding to that key will be set to 1. The table shows the
relationship between those pins and the key data bits.
KS1
KI1
KI2
KI3
KI4
KI5
KD1
KD2
KD3
KD4
KD5
KS2
KD6
KD7
KD8
KD9
KD10
KS3
KD11
KD12
KD13
KD14
KD15
KS4
KD16
KD17
KD18
KD19
KD20
KS5
KD21
KD22
KD23
KD24
KD25
KS6
KD26
KD27
KD28
KD29
KD30
When the states of the KS1 to KS6 output pins during key scan standby are set to low for KS1 and KS2 and to high
for KS3 to KS6 by the KC1 to KC6 bits in the control data and a key matrix of up to 20 keys is formed from the KS3
to KS6 output pins and the KI1 to KI5 input pins, the KD1 to KD10 key data bits will be set to 0.
2. SA : Sleep acknowledge data
This output data bit is set to the state when the key was pressed. Also, while DO will be low in this case, if serial data
is input and the mode is set (to normal or sleep mode) during this period, that mode will be set. SA will be 1 in sleep
mode and 0 in normal mode.
No. 6370 -22/39
LC75808E, 75808W
Key Scan Operation Functions
1. Key scan timing
The key scan period is 384T(s). To reliably determine the on/off state of the keys, the LC75808E/W scans the keys
twice and determines that a key has been pressed when the key data agrees. It outputs a key data read request (a low
level on DO) 800T(s) after starting a key scan. If the key data dose not agree and a key was pressed at that point, it
scans the keys again. Thus the LC75808E/W cannot detect a key press shorter than 800T(s).
*3
*3
*3
*3
*3
*3
*3
*3
*3
*3
*3
*3
Note: *3. Note that the high/low states of these pins are determined by the KC1 to KC6 bits in the control data, and that key scan output signals are not
output from pins that are set to low.
2. In normal mode
• The pins KS1 to KS6 are set to high or low by the KC1 to KC6 bits in the control data.
• If a key on one of the lines corresponding to a KS1 to KS6 pin which is set high is pressed, a key scan is started
and the keys are scanned until all keys are released. Multiple key presses are recognized by determining whether
multiple key data bits are set.
1 ) the LC75808E/W outputs a key data read request (a
• If a key is pressed for longer than 800T(s) (Where T= ——
fosc
low level on DO) to the controller. The controller acknowledges this request and reads the key data. However, if
CE is high during a serial data transfer, DO will be set high.
• After the controller reads the key data, the key data read request is cleared (DO is set high) and the LC75808E/W
performs another key scan. Also note that DO, being an open-drain output, requires a pull-up resistor (between
1 kΩ and 10 kΩ).
No. 6370 -23/39
LC75808E, 75808W
3. In sleep mode
• The pins KS1 to KS6 are set to high or low by the KC1 to KC6 bits in the control data.
• If a key on one of the lines corresponding to a KS1 to KS6 pin which is set high is pressed, the oscillator on the
OSC pin is started and a key scan is performed. Keys are scanned until all keys are released. Multiple key presses
are recognized by determining whether multiple key data bits are set.
1 ) the LC75808E/W outputs a key data read request (a
• If a key is pressed for longer than 800T(s)(where T= ——
fosc
low level on DO) to the controller. The controller acknowledges this request and reads the key data. However, if
CE is high during a serial data transfer, DO will be set high.
• After the controller reads the key data, the key data read request is cleared (DO is set high) and the LC75808E/W
performs another key scan. However, this dose not clear sleep mode. Also note that DO, being an open-drain
output, requires a pull-up resistor (between 1 kΩ and 10 kΩ).
• Sleep mode key scan example
Example: When the control data bits KC1 to KC5 are 0, KC6 is 1, and SP is 1. (sleep with only KS6 high)
[L]
[L]
[L]
[L]
[L]
[H]
Note: *4.These diodes are required to reliable recognize multiple key presses on the KS6 line when sleep mode state with only KS6 high, as in the above
example. That is, these diodes prevent incorrect operations due to sneak currents in the KS6 key scan output signal when keys on the KS1 to KS5
lines are pressed at the same time.
Multiple Key Presses
Although the LC75808E/W is capable of key scanning without inserting diodes for dual key presses, triple key presses on
the KI1 to KI5 input pin lines, or multiple key presses on the KS1 to KS6 output pin lines, multiple presses other than
these cases may result in keys that were not pressed recognized as having been pressed. Therefore, a diode must be
inserted in series with each key. Applications that do not recognize multiple key presses of three or more keys should
check the key data for three or more 1 bits and ignore such data.
No. 6370 -24/39
LC75808E, 75808W
1/8 Duty, 1/4 Bias Drive Technique
COM1
COM2
..
..
..
..
..
..
..
..
.
COM8
LCD driver output when all LCD segments
corresponding to COM1 to COM8 are turned off
LCD driver output when only LCD segments
corresponding to COM1 are turned on
LCD driver output when only LCD segments
corresponding to COM2 are turned on
LCD driver output when all LCD segments
corresponding to COM1 to COM8 are turned on
No. 6370 -25/39
LC75808E, 75808W
1/9 Duty, 1/4 Bias Drive Technique
COM1
COM2
..
..
..
..
..
..
..
..
.
COM9
LCD driver output when all LCD segments
corresponding to COM1 to COM9 are turned off
LCD driver output when only LCD segments
corresponding to COM1 are turned on
LCD driver output when only LCD segments
corresponding to COM2 are turned on
LCD driver output when all LCD segments
corresponding to COM1 to COM9 are turned on
No. 6370 -26/39
LC75808E, 75808W
1/10 Duty, 1/4 Bias Drive Technique
COM1
COM2
..
..
..
..
..
..
..
..
.
COM10
LCD driver output when all LCD segments
corresponding to COM1 to COM10 are turned off
LCD driver output when only LCD segments
corresponding to COM1 are turned on
LCD driver output when only LCD segments
corresponding to COM2 are turned on
LCD driver output when all LCD segments
corresponding to COM1 to COM10 are turned on
No. 6370 -27/39
LC75808E, 75808W
Voltage Detection Type Reset Circuit (VDET)
This circuit generates an output signal and resets the system when logic block power is first applied and when the voltage
drops, i.e., when the logic block power supply voltage is less than or equal to the power down detection voltage VDET,
which is 3.0V, typical. To assure that this function operates reliably, a capacitor must be added to the logic block power
supply line so that the logic block power supply voltage VDD rise time when the logic block power is first applied and the
logic block power supply voltage VDD fall time when the voltage drops are both at least 1 ms. (See Figure 3, 4, and 5.)
Power Supply Sequence
The following sequences must be observed when power is turned on and off. (See Figure 3, 4, and 5.)
• Power on :Logic block power supply(VDD) on → LCD driver block power supply(VLCD) on
• Power off:LCD driver block power supply(VLCD) off → Logic block power supply(VDD) off
However, if the logic and LCD driver blocks use a shared power supply, then the power supplies can be turned on and off
at the same time.
System Reset
1. Reset Function
The LC75808E/W performs a system reset with the VDET. When a system reset is applied, the display is turned off, key
scanning is disabled, the key data is reset, and the general-purpose output ports are set to and held at the low level (VSS).
These states that are created as a result of the system reset can be cleared by executing the instruction described below.
(See figure 3, 4, and 5.)
• Clearing the display off state
Transferring all the serial data (the display data and the control data) creates a state in which the display is turned on.
• Clearing the key scan disabled and key data reset states
Transferring the control data not only creates a state in which key scanning can be performed, but also clears the key
data reset.
• Clearing the general-purpose output ports locked at the low level (VSS) state
Transferring the control data clears the general-purpose output ports locked at the low level (VSS) state and sets the
states of the general-purpose output ports.
• 1/8 duty
VDD
VLCD
CE
Internal data (KC1 to KC6, PC1 to
PC4, CT0 to CT3, CTC,
SC, SP, DT1, DT2)
Undefined
Defined
Undefined
Internal data (D1 to D120)
Undefined
Defined
Undefined
Internal data (D121 to D240)
Undefined
Defined
Undefined
Internal data (D241 to D360)
Undefined
Defined
Undefined
Internal data (D361 to D480)
Undefined
Defined
Undefined
Key scan
General-purpose output ports
Display state
Execution enabled
Disabled
Fixed at the low level (VSS)
Can be set to either the high (VDD) or low (VSS) level.
Display off
Display on
• t1 ≥ 1 ms (Logic block power supply voltage VDD rise time)
• t2 ≥ 0
• t3 ≥ 0
• t4 ≥ 1 ms (Logic block power supply voltage VDD fall time)
Figure 3
No. 6370 -28/39
LC75808E, 75808W
• 1/9 duty
VDD
VLCD
CE
Internal data (KC1 to KC6, PC1 to
PC4, CT0 to CT3, CTC,
SC, SP, DT1, DT2)
Undefined
Defined
Undefined
Internal data (D1 to D135)
Undefined
Defined
Undefined
Internal data (D136 to D270)
Undefined
Defined
Undefined
Internal data (D271 to D405)
Undefined
Defined
Undefined
Internal data (D406 to D540)
Undefined
Defined
Undefined
Key scan
Execution enabled
Disabled
General-purpose output ports
Fixed at the low level (VSS)
Can be set to either the high (VDD) or low (VSS) level.
Display state
Display on
Display off
• t1 ≥ 1 ms (Logic block power supply voltage VDD rise time)
• t2 ≥ 0
• t3 ≥ 0
• t4 ≥ 1 ms (Logic block power supply voltage VDD fall time)
Figure 4
• 1/10 duty
VDD
VLCD
CE
Internal data (KC1 to KC6, PC1 to
PC4, CT0 to CT3, CTC,
SC, SP, DT1, DT2)
Undefined
Defined
Undefined
Internal data (D1 to D150)
Undefined
Defined
Undefined
Internal data (D151 to D300)
Undefined
Defined
Undefined
Internal data (D301 to D450)
Undefined
Defined
Undefined
Internal data (D451 to D600)
Undefined
Defined
Undefined
Key scan
General-purpose output ports
Display state
Disabled
Execution enabled
Fixed at the low level (VSS)
Can be set to either the high (VDD) or low (VSS) level.
Display off
Display on
• t1 ≥ 1 ms (Logic block power supply voltage VDD rise time)
• t2 ≥ 0
• t3 ≥ 0
• t4 ≥ 1 ms (Logic block power supply voltage VDD fall time)
Figure 5
No. 6370 -29/39
LC75808E, 75808W
2. LC75808E/W internal block states during the system reset
• CLOCK GENERATOR
Reset is applied and the base clock is stopped. However, the OSC pin state (normal or sleep mode) is determined
after the SP control data bit is transferred.
• COMMON DRIVER, SEGMENT DRIVER & LATCH
Reset is applied and the display is turned off. However, display data can be input to the latch circuit in this state.
• CONTRAST ADJUSTER
Reset is applied and operation of the display contrast adjustment circuit is disabled. After that, once CT0 to CT3
and CTC in the control data have been transferred to the IC it will then be possible to set the display contrast.
• KEY SCAN, KEY BUFFER
Reset is applied, these circuits are forcibly initialized internally, and key scan operation is disabled. Also, the key
data is all set to 0. After that, once KC1 to KC6 in the control data have been transferred to the IC it will then be
possible to perform key scan operations.
• GENERAL PORT
Reset is applied and the states of the general-purpose output ports are held fixed at the low level (VSS).
• CCB INTERFACE, SHIFT REGISTER, CONTROL REGISTER
Since serial data transfer is possible, these circuits are not reset.
Blocks that are reset
No. 6370 -30/39
LC75808E, 75808W
3. Output pin states during the system reset
Output pin
State during reset
S1 to S60
L (VLCD4)
COM1 to COM10
L (VLCD4)
KS1 to KS6
L (VSS)
P1 to P4
L (VSS)
DO
H *5
Note: *5.
Since this output pin is an open-drain output, a pull-up resistor of between 1 kΩ and 10 kΩ is required. This pin is held at the high level even if a
key data read operation is performed before the KC1 to KC6 control data has been transferred to the IC.
Sample Application Circuit 1
1/8 duty, 1/4 bias drive technique (for use with normal panels)
LCD panel
+5 V
*6
+8 V
*7
C ≥ 0.047 µF
*8
From the controller
general-purpose output ports
To the controller
To the controller
power supply
Used with the backlight
controller or other circuit.
*9
Key matrix
(up to 30 keys)
Note: *6.
*7.
*8.
*9.
Add a capacitor to the logic block power supply line so that the logic block power supply voltage VDD rise time when power is applied and the
logic block power supply voltage VDD fall time when power drops are both at least 1 ms, as the LC75808E/W is reset by the VDET.
If a variable resistor is not used for display contrast fine adjustment, the VLCD4 pin must be connected to ground.
If the function of the INH pin is not used, the INH pin must be connected to the logic block power supply VDD.
The DO pin, being an open-drain output, requires a pull-up resistor. Select a resistance (between 1 kΩ to 10 kΩ) appropriate for the capacitance
of the external wiring so that signal waveforms are not degraded.
No. 6370 -31/39
LC75808E, 75808W
Sample Application Circuit 2
1/8 duty, 1/4 bias drive technique (for use with large panels)
LCD panel
+5 V
*6
+8 V
*7
C ≥ 0.047 µF
10 kΩ ≥ R ≥ 2.2 kΩ
*8
From the controller
general-purpose output ports
To the controller
To the controller
power supply
Used with the backlight
controller or other circuit.
*9
Key matrix
(up to 30 keys)
Note: *6.
*7.
*8.
*9.
Add a capacitor to the logic block power supply line so that the logic block power supply voltage VDD rise time when power is applied and the
logic block power supply voltage VDD fall time when power drops are both at least 1 ms, as the LC75808E/W is reset by the VDET.
If a variable resistor is not used for display contrast fine adjustment, the VLCD4 pin must be connected to ground.
If the function of the INH pin is not used, the INH pin must be connected to the logic block power supply VDD.
The DO pin, being an open-drain output, requires a pull-up resistor. Select a resistance (between 1 kΩ to 10 kΩ) appropriate for the capacitance
of the external wiring so that signal waveforms are not degraded.
No. 6370 -32/39
LC75808E, 75808W
Sample Application Circuit 3
1/9 duty, 1/4 bias drive technique (for use with normal panels)
LCD panel
+5 V
*6
+8 V
*7
C ≥ 0.047 µF
*8
From the controller
general-purpose output ports
To the controller
To the controller
power supply
Used with the backlight
controller or other circuit.
*9
Key matrix
(up to 30 keys)
Note: *6.
*7.
*8.
*9.
Add a capacitor to the logic block power supply line so that the logic block power supply voltage VDD rise time when power is applied and the
logic block power supply voltage VDD fall time when power drops are both at least 1 ms, as the LC75808E/W is reset by the VDET.
If a variable resistor is not used for display contrast fine adjustment, the VLCD4 pin must be connected to ground.
If the function of the INH pin is not used, the INH pin must be connected to the logic block power supply VDD.
The DO pin, being an open-drain output, requires a pull-up resistor. Select a resistance (between 1 kΩ to 10 kΩ) appropriate for the capacitance
of the external wiring so that signal waveforms are not degraded.
No. 6370 -33/39
LC75808E, 75808W
Sample Application Circuit 4
1/9 duty, 1/4 bias drive technique (for use with large panels)
LCD panel
+5 V
*6
+8 V
*7
C ≥ 0.047 µF
10 kΩ ≥ R ≥ 2.2 kΩ
*8
From the controller
general-purpose output ports
To the controller
To the controller
power supply
Used with the backlight
controller or other circuit.
*9
Key matrix
(up to 30 keys)
Note: *6.
*7.
*8.
*9.
Add a capacitor to the logic block power supply line so that the logic block power supply voltage VDD rise time when power is applied and the
logic block power supply voltage VDD fall time when power drops are both at least 1 ms, as the LC75808E/W is reset by the VDET.
If a variable resistor is not used for display contrast fine adjustment, the VLCD4 pin must be connected to ground.
If the function of the INH pin is not used, the INH pin must be connected to the logic block power supply VDD.
The DO pin, being an open-drain output, requires a pull-up resistor. Select a resistance (between 1 kΩ to 10 kΩ) appropriate for the capacitance
of the external wiring so that signal waveforms are not degraded.
No. 6370 -34/39
LC75808E, 75808W
Sample Application Circuit 5
1/10 duty, 1/4 bias drive technique (for use with normal panels)
LCD panel
+5 V
*6
+8 V
*7
C ≥ 0.047 µF
*8
From the controller
general-purpose output ports
To the controller
To the controller
power supply
Used with the backlight
controller or other circuit.
*9
Key matrix
(up to 30 keys)
Note: *6.
*7.
*8.
*9.
Add a capacitor to the logic block power supply line so that the logic block power supply voltage VDD rise time when power is applied and the
logic block power supply voltage VDD fall time when power drops are both at least 1 ms, as the LC75808E/W is reset by the VDET.
If a variable resistor is not used for display contrast fine adjustment, the VLCD4 pin must be connected to ground.
If the function of the INH pin is not used, the INH pin must be connected to the logic block power supply VDD.
The DO pin, being an open-drain output, requires a pull-up resistor. Select a resistance (between 1 kΩ to 10 kΩ) appropriate for the capacitance
of the external wiring so that signal waveforms are not degraded.
No. 6370 -35/39
LC75808E, 75808W
Sample Application Circuit 6
1/10 duty, 1/4 bias drive technique (for use with large panels)
LCD panel
+5 V
*6
+8 V
*7
C ≥ 0.047 µF
10 kΩ ≥ R ≥ 2.2 kΩ
*8
From the controller
general-purpose output ports
To the controller
To the controller
power supply
Used with the backlight
controller or other circuit.
*9
Key matrix
(up to 30 keys)
Note: *6.
*7.
*8.
*9.
Add a capacitor to the logic block power supply line so that the logic block power supply voltage VDD rise time when power is applied and the
logic block power supply voltage VDD fall time when power drops are both at least 1 ms, as the LC75808E/W is reset by the VDET.
If a variable resistor is not used for display contrast fine adjustment, the VLCD4 pin must be connected to ground.
If the function of the INH pin is not used, the INH pin must be connected to the logic block power supply VDD.
The DO pin, being an open-drain output, requires a pull-up resistor. Select a resistance (between 1 kΩ to 10 kΩ) appropriate for the capacitance
of the external wiring so that signal waveforms are not degraded.
Notes on Transferring Display Data from the Controller
The display data is transferred to the LC75808E/W in four operations. All of the display data should be transferred within
30 ms to maintain the quality of the displayed image.
No. 6370 -36/39
LC75808E, 75808W
Notes on the Controller Key Data Read Techniques
1. Timer based key data acquisition
• Flowchart
CE = [ L ]
DO = [ L ]
• Timing chart
t5: Key scan execution time when the key data agreed for two key scans. (800T(s))
t6: Key scan execution time when the key data did not agree for two key scans and the key scan was executed again.
(1600T(s))
t7: Key address (43H) transfer time
1
T = ———
t8: Key data read time
fosc
• Explanation
In this technique, the controller uses a timer to determine key on/off states and read the key data. The controller must
check the DO state when CE is low every t9 period without fail. If DO is low, the controller recognizes that a key has
been pressed and executes the key data read operation.
The period t9 in this technique must satisfy the following condition.
t9 > t6 + t7 + t8
If a key data read operation is executed when DO is high, the read key data (KD1 to KD30) and sleep acknowledge
data (SA) will be invalid.
No. 6370 -37/39
LC75808E, 75808W
2. Interrupt based key data acquisition
• Flowchart
CE = [ L ]
DO = [ L ]
CE = [ L ]
DO = [ H ]
• Timing chart
t5: Key scan execution time when the key data agreed for two key scans. (800T(S))
t6: Key scan execution time when the key data did not agree for two key scans and the key scan was executed again.
(1600T(S))
t7: Key address (43H) transfer time
1
T = ———
t8: Key data read time
fosc
No. 6370 -38/39
LC75808E, 75808W
• Explanation
In this technique, the controller uses interrupts to determine key on/off states and read the key data. The controller must
check the DO state when CE is low. If DO is low, the controller recognizes that a key has been pressed and executes
the key data read operation. After that the next key on/off determination is performed after the time t10 has elapsed by
checking the DO state when CE is low and reading the key data. The period t10 in this technique must satisfy the
following condition.
t10 > t6
If a key data read operation is executed when DO is high, the read key data (KD1 to KD30) and sleep acknowledge
data (SA) will be invalid.
Specifications of any and all SANYO products described or contained herein stipulate the performance,
characteristics, and functions of the described products in the independent state, and are not guarantees
of the performance, characteristics, and functions of the described products as mounted in the customer’s
products or equipment. To verify symptoms and states that cannot be evaluated in an independent device,
the customer should always evaluate and test devices mounted in the customer’s products or equipment.
SANYO Electric Co., Ltd. strives to supply high-quality high-reliability products. However, any and all
semiconductor products fail with some probability. It is possible that these probabilistic failures could
give rise to accidents or events that could endanger human lives, that could give rise to smoke or fire,
or that could cause damage to other property. When designing equipment, adopt safety measures so
that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective
circuits and error prevention circuits for safe design, redundant design, and structural design.
In the event that any or all SANYO products (including technical data, services) described or contained
herein are controlled under any of applicable local export control laws and regulations, such products must
not be exported without obtaining the export license from the authorities concerned in accordance with the
above law.
No part of this publication may be reproduced or transmitted in any form or by any means, electronic or
mechanical, including photocopying and recording, or any information storage or retrieval system,
or otherwise, without the prior written permission of SANYO Electric Co., Ltd.
Any and all information described or contained herein are subject to change without notice due to
product/technology improvement, etc. When designing equipment, refer to the “Delivery Specification”
for the SANYO product that you intend to use.
Information (including circuit diagrams and circuit parameters) herein is for example only; it is not
guaranteed for volume production. SANYO believes information herein is accurate and reliable, but
no guarantees are made or implied regarding its use or any infringements of intellectual property rights
or other rights of third parties.
This catalog provides information as of March, 2000. Specifications and information herein are subject to
change without notice.
PS No. 6370 -39/39