Ordering number : ENN6266A CMOS IC LC75804E, LC75804W 1/3, 1/4 Duty LCD Display Drivers with Key Input Function Overview Package Dimensions The LC75804E and LC75804W are 1/3 duty and 1/4 duty LCD display drivers that can directly drive up to 300 segments and can control up to eight general-purpose output ports. These products also incorporate a key scan circuit that accepts input from up to 30 keys to reduce printed circuit board wiring. unit: mm 3151A-QFP100E [LC75804E] 23.2 51 50 14.0 Features 100 17.2 81 31 1 30 0.65 0.15 0.3 0.1 3.0max (2.7) (0.58) SANYO: QFP100E(QIP100E) unit: mm 3181C-SQFP100 [LC75804W] 16.0 0.5 14.0 51 50 100 26 14.0 76 1 0.5 0.2 16.0 75 25 0.145 0.1 (1.4) (1.0) 1.6max • Key input function for up to 30 keys (A key scan is performed only when a key is pressed.) • 1/3 duty and 1/4 duty drive schemes can be controlled from serial data. • 1/2 bias and 1/3 bias drive schemes can be controlled from serial data. • Capable of driving up to 228 segments using 1/3 duty and up to 300 segments using 1/4 duty. • Sleep mode and all segments off functions that are controlled from serial data. • Segment output port/general-purpose output port function switching that is controlled from serial data. • Serial data I/O supports CCB format communication with the system controller. • Direct display of display data without the use of a decoder provides high generality. • Independent VLCD for the LCD driver block (VLCD can be set to in the range VDD – 0.5 to 6.0 volts.) • Provision of an on-chip voltage-detection type reset circuit prevents incorrect displays. • RES pin provided for forcibly initializing the IC internal circuits. • RC oscillator circuit. 0.8 20.0 80 • CCB is a trademark of SANYO ELECTRIC CO., LTD. SANYO: SQFP100 • CCB is SANYO’s original bus format and all the bus addresses are controlled by SANYO. Any and all SANYO products described or contained herein do not have specifications that can handle applications that require extremely high levels of reliability, such as life-support systems, aircraft’s control systems, or other applications whose failure can be reasonably expected to result in serious physical and/or material damage. Consult with your SANYO representative nearest you before using any SANYO products described or contained herein in such applications. SANYO assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all SANYO products described or contained herein. SANYO Electric Co.,Ltd. Semiconductor Company TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110-8534 JAPAN 51003AS / D2599TH (OT) No. 6266-1/37 LC75804E, LC75804W Specifications Absolute Maximum Ratings at Ta=25°C, VSS=0V Parameter Maximum supply voltage Input voltage Output voltage Output current Allowable power dissipation Symbol Conditions Ratings Unit VDD max VDD –0.3 to +7.0 VLCD max VLCD –0.3 to +7.0 VIN1 CE, CL, DI, RES VIN2 OSC,TEST VIN3 VLCD1, VLCD2, KI1 to KI5 –0.3 to +7.0 –0.3 to VDD +0.3 V –0.3 to VLCD +0.3 VOUT1 DO VOUT2 OSC VOUT3 S1 to S76, COM1 to COM4, KS1 to KS6, P1 to P8 IOUT1 S1 to S76 IOUT2 COM1 to COM4 3 IOUT3 KS1 to KS6 1 IOUT4 P1 to P8 5 Pd max V –0.3 to +7.0 –0.3 to VDD +0.3 V –0.3 to VLCD +0.3 300 Ta = 85°C 200 µA mA mW Operating temperature Topr –40 to +85 °C Storage temperature Tstg –55 to +125 °C Allowable Operating Ranges at Ta = –40 to +85°C, VSS=0V Parameter Supply voltage Input voltage Input high level voltage Input low level voltage Symbol Ratings Conditions min typ Unit max VDD VDD VLCD VLCD VLCD1 VLCD1 2/3 VLCD VLCD VLCD2 VLCD2 1/3 VLCD VLCD 4.5 6.0 VDD – 0.5 6.0 VIH1 CE, CL, DI, RES 0.8 VDD 6.0 VIH2 KI1 to KI5 0.6 VDD VLCD VIL CE, CL, DI, RES, KI1 to KI5 Recommended external resistance ROSC OSC Recommended external capacitance COSC OSC Guaranteed oscillator range fOSC OSC 0 0.2 VDD 39 38 V V V kΩ 1000 19 V pF 76 kHz Data setup time tds CL, DI :Figure 2 160 ns Data hold time tdh CL, DI :Figure 2 160 ns CE wait time tcp CE, CL :Figure 2 160 ns CE setup time tcs CE, CL :Figure 2 160 ns CE hold time tch CE, CL :Figure 2 160 ns High level clock pulse width tøH CL :Figure 2 160 ns Low level clock pulse width tøL CL :Figure 2 160 ns Rise time tr CE, CL, DI :Figure 2 160 Fall time tf CE, CL, DI :Figure 2 160 ns ns DO output delay time tdc DO RPU=4.7 kΩ, CL=10pF *1 :Figure 2 1.5 µs DO rise time tdr DO RPU=4.7 kΩ, CL=10pF *1 :Figure 2 1.5 µs Note: *1. Since DO is an open-drain output, these values depend on the resistance of the pull-up resistor RPU and the load capacitance CL. No. 6266-2/37 LC75804E, LC75804W Electrical Characteristics for the Allowable Operating Ranges Parameter Hysteresis Power-down detection voltage Input high level current Symbol VH Conditions IIH CE, CL, DI, RES: VI = 6.0 V IIL CE, CL, DI, RES: VI = 0 V VIF KI1 to KI5 Pull-down resistance RPD KI1 to KI5: VDD = 5.0 V Output low level voltage Output middle level voltage *2 Oscillator frequency Unit max 0.1 VDD 2.5 Input low level current Output high level voltage typ CE, CL, DI, RES, KI1 to KI5 VDET Input floating voltage Output off leakage current Ratings min 3.0 V 3.5 V 5.0 µA –5.0 µA 0.05 VDD 50 100 kΩ 6.0 µA IOFFH DO: VO = 6.0 V VOH1 KS1 to KS6: IO = –500 µA VLCD – 1.0 VLCD – 0.5 VLCD – 0.2 VOH2 P1 to P8: IO = –1 mA VLCD – 1.0 VOH3 S1 to S76: IO = –20 µA VLCD – 1.0 VOH4 COM1 to COM4: IO = –100 µA VLCD – 1.0 VOL1 KS1 to KS6: IO = 25 µA VOL2 P1 to P8: IO = 1 mA VOL3 S1 to S76: IO = 20 µA 1.0 VOL4 COM1 to COM4: IO = 100 µA 1.0 0.2 V 0.5 1.5 1.0 VOL5 DO: IO = 1 mA VMID1 COM1 to COM4: 1/2 bias, IO = ±100 µA 1/2 VLCD – 1.0 1/2 VLCD + 1.0 VMID2 S1 to S76: 1/3 bias,IO = ±20 µA 2/3 VLCD – 1.0 2/3 VLCD + 1.0 VMID3 S1 to S76: 1/3 bias, IO = ±20 µA 1/3 VLCD – 1.0 1/3 VLCD + 1.0 VMID4 COM1 to COM4: 1/3 bias,IO = ±100 µA 2/3 VLCD – 1.0 2/3 VLCD + 1.0 VMID5 COM1 to COM4: 1/3 bias,IO = ±100 µA 1/3 VLCD – 1.0 fosc OSC: ROSC = 39 kΩ, COSC = 1000 pF IDD1 VDD :Sleep mode 0.1 30.4 V 0.5 V 1/3 VLCD + 1.0 38 45.6 kHz 100 IDD2 VDD: VDD = 6.0 V, output open,fosc = 38 kHz ILCD1 VLCD : Sleep mode ILCD2 VLCD: VLCD = 6.0 V, output open, 1/2 bias, fosc = 38 kHz 200 400 ILCD3 VLCD: VLCD = 6.0 V, output open, 1/3 bias, fosc = 38 kHz 120 240 Current drain V 250 270 540 5 µA Nete: *2. Excluding the bias voltage generation divider resistor built into VLCD1 and VLCD2. (See Figure 1.) No. 6266-3/37 LC75804E, LC75804W VLCD VLCD1 To the common segment driver VLCD2 Excluding these registors. Figure 1 1. When CL is stopped at the low level VIH1 CE CL VIL tøH VIH1 50% VIL tøL tr DI tf tcp tcs tch VIH1 VIL tds tdh tdc DO D0 tdr D1 2. When CL is stopped at the high level VIH1 CE VIL tø L tø H CL tf tr tcp tcs tch VIH1 VIL DI tds DO VIH1 50% VIL tdh D0 D1 tdc tdr Figure 2 No. 6266-4/37 LC75804E, LC75804W KS1/S75 COM1 COM2 COM3 COM4/S74 S73 S72 S71 S70 S69 S68 S67 S66 S65 S64 S63 S62 S61 S60 S59 S58 S57 S56 S55 S54 S53 S52 S51 S50 S49 Pin Assignments 80 51 81 50 S76/KS2 KS3 KS4 KS5 KS6 KI1 KI2 KI3 KI4 KI5 VDD VLCD VLCD1 VLCD2 VSS TEST OSC RES DO CE S48 S47 S46 S45 S44 S43 S42 S41 S40 S39 S38 S37 S36 S35 S34 S33 S32 S31 S30 S29 LC75804E (QFP100E) 100 31 30 (Top view) COM3 COM4/S74 S73 S72 S71 S70 S69 S68 S67 S66 S65 S64 S63 S62 S61 S60 S59 S58 S57 S56 S55 S54 S53 S52 S51 CL DI P1/S1 P2/S2 P3/S3 P4/S4 P5/S5 P6/S6 P7/S7 P8/S8 S9 S10 S11 S12 S13 S14 S15 S16 S17 S18 S19 S20 S21 S22 S23 S24 S25 S26 S27 S28 1 75 51 76 50 COM2 COM1 S75/KS1 S76/KS2 KS3 KS4 KS5 KS6 KI1 KI2 KI3 KI4 KI5 VDD VLCD VLCD1 VLCD2 VSS TEST OSC RES DO CE CL DI S50 S49 S48 S47 S46 S45 S44 S43 S42 S41 S40 S39 S38 S37 S36 S35 S34 S33 S32 S31 S30 S29 S28 S27 S26 LC75804W (SQFP100) 100 26 25 P1/S1 P2/S2 P3/S3 P4/S4 P5/S5 P6/S6 P7/S7 P8/S8 S9 S10 S11 S12 S13 S14 S15 S16 S17 S18 S19 S20 S21 S22 S23 S24 S25 1 (Top view) No. 6266-5/37 LC75804E, LC75804W S1/P1 S2/P2 S9 S8/P8 S73 COM1 COM2 COM3 COM4/S74 Block Diagram VLCD SEGMENT DRIVER & LATCH VLCD1 COMMON DRIVER VLCD2 SHIFT REGISTER VSS TEST CLOCK GENERATOR OSC CONTROL REGISTER DO CCB INTERFACE DI CL CE KEY BUFFER VDD VDET KS6 KS5 KS4 KS3 S76/KS2 S75/KS1 KI5 KI4 KI3 KI2 KI1 RES KEY SCAN No. 6266-6/37 LC75804E, LC75804W Pin Functions Pin Pin No. LC75804E LC75804W S1/P1 to S8/P8 S9 to S73 3 to 10 1 to 8 11 to 75 9 to 73 COM1 COM2 COM3 COM4/S74 79 78 77 76 77 76 75 74 Function Active I/O Handling when unused Segment outputs for displaying the display data transferred by serial data input. The S1/P1 to S8/P8 pins can be used as general-purpose output ports under serial data control. — ● OPEN Common driver outputs The frame frequency fo is given by : fo = (fOSC/384)Hz. The COM4/S74 pin can be used as a segment output in 1/3 duty. — ● OPEN — O OPEN KS1/S75 KS2/S76 KS3 to KS6 80 81 82 to 85 78 79 80 to 83 Key scan outputs Although normal key scan timing lines require diodes to be inserted in the timing lines to prevent shorts, since these outputs are unbalanced CMOS transistor outputs, these outputs will not be damaged by shorting when these outputs are used to form a key matrix. The KS1/S75 and KS2/S76 pins can be used as segment outputs when so specified by the control data. KI1 to KI5 86 to 90 84 to 88 Key scan inputs These pins have built-in pull-down resistors. H I GND OSC 97 95 Oscillator connection An oscillator circuit is formed by connecting an external resistor and capacitor at this pin. — I/O VDD CE 100 98 H I CL 1 99 ▲ I DI 2 100 — I DO 99 97 — O OPEN Reset signal input RES = low.....Display off Key scan disabled All key data is reset to low RES = high....Display on Key scan enabled However, serial data can be transferred when RES is low. L I VDD Serial data interface connections to the controller. Note that DO, being an open-drain output, requires a pull-up resistor. CE :Chip enable CL :Synchronization clock DI :Transfer data DO :Output data GND RES 98 96 TEST 96 94 This pin must be connected to ground. — I — — I OPEN VLCD1 93 91 Used for applying the LCD drive 2/3 bias voltage externally. Must be connected to VLCD2 when a 1/2 bias drive scheme is used. VLCD2 94 92 Used for applying the LCD drive 1/3 bias voltage externally. Must be connected to VLCD1 when a 1/2 bias drive scheme is used. — I OPEN VDD 91 89 Logic block power supply connection. Provide a voltage of between 4.5 and 6.0V. — — — VLCD 92 90 LCD driver block power supply connection. Provide a voltage of between VDD – 0.5 and 6.0V. — — — VSS 95 93 Power supply connection. Connect to ground. — — — No. 6266-7/37 LC75804E, LC75804W Serial Data Input 1. 1/3 duty ① When CL is stopped at the low level CE CL DI 0 1 0 0 0 0 1 0 D1 D2 D73 D74 D75 D76 D77 D78 0 B0 B1 B2 B3 A0 A1 A2 A3 0 0 0 0 S0 S1 K0 K1 P0 P1 P2 P3 SC DR DT Display data Control data 0 0 DD DO 0 1 0 0 0 0 1 0 B0 B1 B2 B3 A0 A1 A2 A3 0 1 0 0 0 0 1 0 B0 B1 B2 B3 A0 A1 A2 A3 D79 D80 D151 D152 D153 0 0 0 0 0 0 0 0 Display data D154 D155 D226 D227 D228 0 Display data 0 0 0 0 0 0 0 0 0 0 0 Fixed data 0 0 0 0 0 0 0 0 0 0 Fixed data 0 1 DD 0 0 0 0 0 0 0 0 1 0 DD Note: B0 to B3, A0 to A3 ...... CCB address DD ................................ Direction data No. 6266-8/37 LC75804E, LC75804W ② When CL is stopped at the high level CE CL DI 0 1 0 0 0 0 1 0 D1 D2 D73 D74 D75 D76 D77 D78 B0 B1 B2 B3 A0 A1 A2 A3 0 0 0 0 0 S0 S1 K0 K1 P0 P1 P2 P3 SC DR DT Display data 0 0 DD Control data DO 0 1 0 0 0 0 1 0 D79 D80 B0 B1 B2 B3 A0 A1 A2 A3 0 1 0 0 0 0 1 0 B0 B1 B2 B3 A0 A1 A2 A3 D151 D152 D153 0 0 0 0 0 0 0 0 D154 D155 D226 D227 D228 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Display data 0 0 0 0 Fixed data 0 1 DD Fixed data Display data 0 0 0 0 0 0 0 0 1 0 DD Note: B0 to B3, A0 to A3 ...... CCB address DD ................................ Direction data CCB address ............ 42H D1 to D228 .............. Display data S0, S1 ...................... Sleep control data K0, K1 ...................... Key scan output/segment output selection data P0 to P3 .................. Segment output port/general-purpose output port selection data SC ............................ Segment on/off control data DR ............................ 1/2 bias or 1/3 bias drive selection data DT ............................ 1/3 duty or 1/4 duty drive selection data No. 6266-9/37 LC75804E, LC75804W 2. 1/4duty ① When CL is stopped at the low level CE CL DI 0 1 0 0 0 0 1 0 D1 D72 D73 D74 D75 D76 0 B0 B1 B2 B3 A0 A1 A2 A3 0 0 0 0 0 0 S0 S1 K0 K1 P0 P1 P2 P3 SC DR DT 0 0 DD Control data Display data DO 0 1 0 0 0 0 1 0 D77 B0 B1 B2 B3 A0 A1 A2 A3 0 1 0 0 0 0 1 0 D153 B0 B1 B2 B3 A0 A1 A2 A3 0 1 0 0 0 0 1 0 B0 B1 B2 B3 A0 A1 A2 A3 D148 D149 D150 D151 D152 0 0 0 0 0 0 0 0 Display data D224 D225 D226 D227 D228 0 0 0 0 0 0 0 0 Display data D229 D300 0 Display data 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Fixed data 0 1 1 0 DD Fixed data 0 0 DD Fixed data 0 0 0 0 0 0 0 0 1 1 DD Note: B0 to B3, A0 to A3 ...... CCB address DD ................................ Direction data No. 6266-10/37 LC75804E, LC75804W ② When CL is stopped at the high level CE CL DI 0 1 0 0 0 0 1 0 D1 B0 B1 B2 B3 A0 A1 A2 A3 D72 D73 D74 D75 D76 0 0 0 0 0 0 0 S0 S1 K0 K1 P0 P1 P2 P3 SC DR DT 0 0 DD Control data Display data DO 0 1 0 0 0 0 1 0 D77 B0 B1 B2 B3 A0 A1 A2 A3 0 1 0 0 0 0 1 0 D153 B0 B1 B2 B3 A0 A1 A2 A3 0 1 0 0 0 0 1 0 B0 B1 B2 B3 A0 A1 A2 A3 D148 D149 D150 D151 D152 0 0 0 0 0 0 0 0 Display data D224 D225 D226 D227 D228 0 0 0 0 0 0 0 0 D300 0 Display data 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Fixed data 0 0 0 1 DD 0 0 0 0 0 0 0 Fixed data Display data D229 0 Fixed data 1 0 DD 0 0 0 0 0 0 0 1 1 DD Note: B0 to B3, A0 to A3 ...... CCB address DD ................................ Direction data CCB address ............ 42H D1 to D300 .............. Display data S0, S1 ...................... Sleep control data K0, K1 ...................... Key scan output/segment output selection data P0 to P3 .................. Segment output port/general-purpose output port selection data SC ............................ Segment on/off control data DR ............................ 1/2 bias or 1/3 bias drive selection data DT ............................ 1/3 duty or 1/4 duty drive selection data No. 6266-11/37 LC75804E, LC75804W Control Data Functions 1. S0, S1 : Sleep control data These control data bits switch between normal mode and sleep mode and set the states of the KS1 to KS6 key scan outputs during key scan standby. Control data Output pin states during key scan standby Mode OSC oscillator Segment outputs Common outputs KS1 KS2 KS3 KS4 KS5 KS6 0 Normal Operating Operating H H H H H H 0 1 Sleep Stopped L L L L L L H 1 0 Sleep Stopped L L L L L H H 1 1 Sleep Stopped L H H H H H H S0 S1 0 Note: This assumes that the KS1/S75 and KS2/S76 output pins are selected for key scan output. 2. K0, K1 : Key scan output /segment output selection data These control data bits switch the functions of the KS1/S75 and KS2/S76 output pins between key scan output and segment output. Control data Output pin state K0 K1 KS1/S75 KS2/S76 Maximum number of input keys 0 0 KS1 KS2 30 0 1 S75 KS2 25 1 X S75 S76 20 X: don’t care Note: KSn(n = 1 or 2) : Key scan output Sn (n = 75 or 76): Segment output 3. P0 to P3 : Segment output port/general-purpose output port selection data These control data bits switch the functions of the S1/P1 to S8/P8 output pins between the segment output port and the general-purpose output port. Control data Output pin state P0 P1 P2 P3 S1/P1 S2/P2 S3/P3 S4/P4 S5/P5 S6/P6 S7/P7 S8/P8 0 0 0 0 S1 S2 S3 S4 S5 S6 S7 S8 0 0 0 1 P1 S2 S3 S4 S5 S6 S7 S8 0 0 1 0 P1 P2 S3 S4 S5 S6 S7 S8 0 0 1 1 P1 P2 P3 S4 S5 S6 S7 S8 0 1 0 0 P1 P2 P3 P4 S5 S6 S7 S8 0 1 0 1 P1 P2 P3 P4 P5 S6 S7 S8 0 1 1 0 P1 P2 P3 P4 P5 P6 S7 S8 0 1 1 1 P1 P2 P3 P4 P5 P6 P7 S8 1 0 0 0 P1 P2 P3 P4 P5 P6 P7 P8 Note: Sn(n=1 to 8): Segment output port Pn(n=1 to 8): General-purpose output port The table below lists the correspondence between the display data and the output pins when these pins are selected to be general-purpose output ports. Output pin Corresponding display data 1/3 duty 1/4 duty S1/P1 D1 D1 S2/P2 D4 D5 S3/P3 D7 D9 S4/P4 D10 D13 S5/P5 D13 D17 S6/P6 D16 D21 S7/P7 D19 D25 S8/P8 D22 D29 For example, if the circuit is operated in 1/4 duty and the S4/P4 output pin is selected to be a general-purpose output port, the S4/P4 output pin will output a high level (VLCD) when the display data D13 is 1, and will output a low level (Vss) when D13 is 0. No. 6266-12/37 LC75804E, LC75804W 4. SC : Segment on/off control data This control data bit controls the on/off state of the segments. SC Display state 0 on 1 off However, note that when the segments are turned off by setting SC to 1, the segments are turned off by outputting segment off waveforms from the segment output pins. 5. DR : 1/2 bias or 1/3 bias drive selection data This control data bit switches between LCD 1/2 bias or 1/3 bias drive. DR Bias drive scheme 0 1/3 bias drive 1 1/2 bias drive 6. DT : 1/3 duty or 1/4 duty drive selection data This control data bit switches between LCD 1/3 duty or 1/4 duty drive. DT Duty drive scheme Output pin state (COM4/S74) 0 1/4 duty drive COM4 1 1/3 duty drive S74 Note: COM4: Common output S74 : Segment output Display Data and Output Pin Correspondence 1. 1/3 duty Output pin COM1 COM2 COM3 Output pin COM1 COM2 COM3 Output pin COM1 COM2 COM3 S1/P1 D1 D2 D3 S27 D79 D80 D81 S53 D157 D158 D159 S2/P2 D4 D5 D6 S28 D82 D83 D84 S54 D160 D161 D162 S3/P3 D7 D8 D9 S29 D85 D86 D87 S55 D163 D164 D165 S4/P4 D10 D11 D12 S30 D88 D89 D90 S56 D166 D167 D168 S5/P5 D13 D14 D15 S31 D91 D92 D93 S57 D169 D170 D171 S6/P6 D16 D17 D18 S32 D94 D95 D96 S58 D172 D173 D174 S7/P7 D19 D20 D21 S33 D97 D98 D99 S59 D175 D176 D177 S8/P8 D22 D23 D24 S34 D100 D101 D102 S60 D178 D179 D180 S9 D25 D26 D27 S35 D103 D104 D105 S61 D181 D182 D183 S10 D28 D29 D30 S36 D106 D107 D108 S62 D184 D185 D186 S11 D31 D32 D33 S37 D109 D110 D111 S63 D187 D188 D189 S12 D34 D35 D36 S38 D112 D113 D114 S64 D190 D191 D192 S13 D37 D38 D39 S39 D115 D116 D117 S65 D193 D194 D195 S14 D40 D41 D42 S40 D118 D119 D120 S66 D196 D197 D198 S15 D43 D44 D45 S41 D121 D122 D123 S67 D199 D200 D201 S16 D46 D47 D48 S42 D124 D125 D126 S68 D202 D203 D204 S17 D49 D50 D51 S43 D127 D128 D129 S69 D205 D206 D207 S18 D52 D53 D54 S44 D130 D131 D132 S70 D208 D209 D210 S19 D55 D56 D57 S45 D133 D134 D135 S71 D211 D212 D213 S20 D58 D59 D60 S46 D136 D137 D138 S72 D214 D215 D216 S21 D61 D62 D63 S47 D139 D140 D141 S73 D217 D218 D219 S22 D64 D65 D66 S48 D142 D143 D144 COM4/S74 D220 D221 D222 S23 D67 D68 D69 S49 D145 D146 D147 KS1/S75 D223 D224 D225 S24 D70 D71 D72 S50 D148 D149 D150 KS2/S76 D226 D227 D228 S25 D73 D74 D75 S51 D151 D152 D153 S26 D76 D77 D78 S52 D154 D155 D156 Note: This is for the case where the output pins S1/P1 to S8/P8, COM4/S74, KS1/S75 and KS2/S76 are selected for use as segment outputs. No. 6266-13/37 LC75804E, LC75804W For example, the table below lists the segment output states for the S11 output pin. Display data Output pin state (S11) D31 D32 D33 0 0 0 The LCD segments for COM1, COM2 and COM3 are off. 0 0 1 The LCD segment for COM3 is on. 0 1 0 The LCD segment for COM2 is on. 0 1 1 The LCD segments for COM2 and COM3 are on. 1 0 0 The LCD segment for COM1 is on. 1 0 1 The LCD segments for COM1 and COM3 are on. 1 1 0 The LCD segments for COM1 and COM2 are on. 1 1 1 The LCD segments for COM1, COM2 and COM3 are on. 2. 1/4 duty Output pin COM1 COM2 COM3 COM4 Output pin COM1 COM2 COM3 COM4 S1/P1 D1 D2 D3 D4 S39 D153 D154 D155 D156 S2/P2 D5 D6 D7 D8 S40 D157 D158 D159 D160 S3/P3 D9 D10 D11 D12 S41 D161 D162 D163 D164 S4/P4 D13 D14 D15 D16 S42 D165 D166 D167 D168 S5/P5 D17 D18 D19 D20 S43 D169 D170 D171 D172 S6/P6 D21 D22 D23 D24 S44 D173 D174 D175 D176 S7/P7 D25 D26 D27 D28 S45 D177 D178 D179 D180 S8/P8 D29 D30 D31 D32 S46 D181 D182 D183 D184 S9 D33 D34 D35 D36 S47 D185 D186 D187 D188 S10 D37 D38 D39 D40 S48 D189 D190 D191 D192 S11 D41 D42 D43 D44 S49 D193 D194 D195 D196 S12 D45 D46 D47 D48 S50 D197 D198 D199 D200 S13 D49 D50 D51 D52 S51 D201 D202 D203 D204 S14 D53 D54 D55 D56 S52 D205 D206 D207 D208 S15 D57 D58 D59 D60 S53 D209 D210 D211 D212 S16 D61 D62 D63 D64 S54 D213 D214 D215 D216 S17 D65 D66 D67 D68 S55 D217 D218 D219 D220 S18 D69 D70 D71 D72 S56 D221 D222 D223 D224 S19 D73 D74 D75 D76 S57 D225 D226 D227 D228 S20 D77 D78 D79 D80 S58 D229 D230 D231 D232 S21 D81 D82 D83 D84 S59 D233 D234 D235 D236 S22 D85 D86 D87 D88 S60 D237 D238 D239 D240 S23 D89 D90 D91 D92 S61 D241 D242 D243 D244 S24 D93 D94 D95 D96 S62 D245 D246 D247 D248 S25 D97 D98 D99 D100 S63 D249 D250 D251 D252 S26 D101 D102 D103 D104 S64 D253 D254 D255 D256 S27 D105 D106 D107 D108 S65 D257 D258 D259 D260 S28 D109 D110 D111 D112 S66 D261 D262 D263 D264 S29 D113 D114 D115 D116 S67 D265 D266 D267 D268 S30 D117 D118 D119 D120 S68 D269 D270 D271 D272 S31 D121 D122 D123 D124 S69 D273 D274 D275 D276 S32 D125 D126 D127 D128 S70 D277 D278 D279 D280 S33 D129 D130 D131 D132 S71 D281 D282 D283 D284 S34 D133 D134 D135 D136 S72 D285 D286 D287 D288 S35 D137 D138 D139 D140 S73 D289 D290 D291 D292 S36 D141 D142 D143 D144 KS1/S75 D293 D294 D295 D296 S37 D145 D146 D147 D148 KS2/S76 D297 D298 D299 D300 S38 D149 D150 D151 D152 Note: This is for the case where the output pins S1/P1 to S8/P8, KS1/S75 and KS2/S76 are selected for use as segment outputs. No. 6266-14/37 LC75804E, LC75804W For example, the table below lists the segment output states for the S11 output pin. Display data D41 D42 D43 D44 Output pin state (S11) 0 0 0 0 The LCD segments for COM1,COM2,COM3 and COM4 are off. 0 0 0 1 The LCD segment for COM4 is on. 0 0 1 0 The LCD segment for COM3 is on. 0 0 1 1 The LCD segments for COM3 and COM4 are on. 0 1 0 0 The LCD segment for COM2 is on. 0 1 0 1 The LCD segments for COM2 and COM4 are on. 0 1 1 0 The LCD segments for COM2 and COM3 are on. 0 1 1 1 The LCD segments for COM2,COM3 and COM4 are on. 1 0 0 0 The LCD segment for COM1 is on. 1 0 0 1 The LCD segments for COM1 and COM4 are on. 1 0 1 0 The LCD segments for COM1 and COM3 are on. 1 0 1 1 The LCD segments for COM1,COM3 and COM4 are on. 1 1 0 0 The LCD segments for COM1 and COM2 are on. 1 1 0 1 The LCD segments for COM1,COM2 and COM4 are on. 1 1 1 0 The LCD segments for COM1,COM2 and COM3 are on. 1 1 1 1 The LCD segments for COM1,COM2,COM3 and COM4 are on. Serial Data Output 1. When CL is stopped at the low level CE CL DI 1 1 0 0 0 0 1 0 B0 B1 B2 B3 A0 A1 A2 A3 DO X KD1 KD2 KD27 KD28 KD29 KD30 SA Output data X: don't care Note: B0 to B3, A0 to A3······CCB address 2. When CL is stopped at the high level CE CL DI 1 1 0 0 0 0 1 0 B0 B1 B2 B3 A0 A1 A2 A3 DO KD28 KD29 KD30 SA X KD1 KD2 KD3 X Output data X: don't care Note: B0 to B3, A0 to A3······CCB address CCB address ...... 43H KD1 to KD30 ........ Key data SA ........................ Sleep acknowledge data Note: If a key data read operation is executed when DO is high, the read key data (KD1 to KD30) and sleep acknowledge data(SA) will be invalid. No. 6266-15/37 LC75804E, LC75804W Output Data 1. KD1 to KD30 : Key data When a key matrix of up to 30 keys is formed from the KS1 to KS6 output pins and the KI1 to KI5 input pins and one of those keys is pressed, the key output data corresponding to that key will be set to 1. The table shows the relationship between those pins and the key data bits. KS1/S75 KI1 KI2 KI3 KI4 KI5 KD1 KD2 KD3 KD4 KD5 KS2/S76 KD6 KD7 KD8 KD9 KD10 KS3 KD11 KD12 KD13 KD14 KD15 KS4 KD16 KD17 KD18 KD19 KD20 KS5 KD21 KD22 KD23 KD24 KD25 KS6 KD26 KD27 KD28 KD29 KD30 When the KS1/S75 and KS2/S76 output pins are selected to be segment outputs by control data bits K0 and K1 and a key matrix of up to 20 keys is formed using the KS3 to KS6 output pins and the KI1 to KI5 input pins, the KD1 to KD10 key data bits will be set to 0. 2. SA : Sleep acknowledge data This output data bit is set to the state when the key was pressed. Also, while DO will be low in this case, if serial data is input and the mode is set (to normal or sleep mode) during this period, that mode will be set. SA will be 1 in sleep mode and 0 in normal mode. Sleep Mode Functions Sleep mode is set up by setting S0 or S1 in the control data to 1. The segment outputs will all go low and the common outputs will also go low, and the oscillator on the OSC pin will stop (it will be started by a key press). This reduces power dissipation. This mode is cleared by sending control data with both S0 and S1 set to 0. However, note that the S1/P1 to S8/P8 outputs can be used as general-purpose output ports according to the state of the P0 to P3 control data bits, even in sleep mode. (See the control data description for details.) No. 6266-16/37 LC75804E, LC75804W Key Scan Operation Functions 1. Key scan timing The key scan period is 288T(s). To reliably determine the on/off state of the keys, the LC75804E/W scans the keys twice and determines that a key has been pressed when the key data agrees. It outputs a key data read request (a low level on DO) 615T(s) after starting a key scan. If the key data dose not agree and a key was pressed at that point, it scans the keys again. Thus the LC75804E/W cannot detect a key press shorter than 615T(s). KS1 *3 KS2 *3 KS3 *3 1 1 *3 2 2 *3 3 3 *3 T= KS4 *3 KS5 *3 4 4 *3 5 KS6 5 6 Key on 1 fosc *3 6 576T[s] Note: *3. In sleep mode the high/low state of these pins is determined by the S0 and S1 bits in the control data. Key scan output signals are not output from pins that are set low. 2. In normal mode • The pins KS1 to KS6 are set high. • When a key is pressed a key scan is started and the keys are scanned until all keys are released. Multiple key presses are recognized by determining whether multiple key data bits are set. 1 ) the LC75804E/W outputs a key data read request (a • If a key is pressed for longer than 615T(s) (Where T= —— fosc low level on DO) to the controller. The controller acknowledges this request and reads the key data. However, if CE is high during a serial data transfer, DO will be set high. • After the controller reads the key data, the key data read request is cleared (DO is set high) and the LC75804E/W performs another key scan. Also note that DO, being an open-drain output, requires a pull-up resistor (between 1 and 10 kΩ). Key input 1 Key input 2 Key scan 615T[s] 615T[s] 615T[s] CE Serial data transfer Serial data transfer Key address (43H) Serial data transfer Key address Key address DI DO Key data read Key data read request Key data read Key data read request Key data read Key data read request 1 T= fosc No. 6266-17/37 LC75804E, LC75804W 3. In sleep mode • The pins KS1 to KS6 are set to high or low by the S0 and S1 bits in the control data. (See the control data description for details.) • If a key on one of the lines corresponding to a KS1 to KS6 pin which is set high is pressed, the oscillator on the OSC pin is started and a key scan is performed. Keys are scanned until all keys are released. Multiple key presses are recognized by determining whether multiple key data bits are set. 1 • If a key is pressed for longer than 615T(s)(Where T= —— fosc ) the LC75804E/W outputs a key data read request (a low level on DO) to the controller. The controller acknowledges this request and reads the key data. However, if CE is high during a serial data transfer, DO will be set high. • After the controller reads the key data, the key data read request is cleared (DO is set high) and the LC75804E/W performs another key scan. However, this dose not clear sleep mode. Also note that DO, being an open-drain output, requires a pull-up resistor (between 1 and 10 kΩ). • Sleep mode key scan example Example: S0 = 0, S1 = 1 (sleep with only KS6 high) [L] KS1 [L] KS2 [L] KS3 [L] KS4 [L] KS5 [H] KS6 When any one of these keys is pressed, the oscillator on the OSC pin is started and the keys are scanned. *4 KI1 KI2 KI3 KI4 KI5 Note: *4. These diodes are required to reliable recognize multiple key presses on the KS6 line when sleep mode state with only KS6 high, as in the above example. That is, these diodes prevent incorrect operations due to sneak currents in the KS6 key scan output signal when keys on the KS1 to KS5 lines are pressed at the same time. Key input (KS6 line) Key scan 615T[s] 615T[s] CE Serial data transfer Serial data transfer Key address (43H) Serial data transfer Key address DI T= 1 fosc DO Key data read Key data read request Key data read Key data read request Multiple Key Presses Although the LC75804E/W is capable of key scanning without inserting diodes for dual key presses, triple key presses on the KI1 to KI5 input pin lines, or multiple key presses on the KS1 to KS6 output pin lines, multiple presses other than these cases may result in keys that were not pressed recognized as having been pressed. Therefore, a diode must be inserted in series with each key. Applications that do not recognize multiple key presses of three or more keys should check the key data for three or more 1 bits and ignore such data. No. 6266-18/37 LC75804E, LC75804W 1/3 Duty, 1/2 Bias Drive Technique fosc 384 [Hz] COM1 VLCD VLCD1,VLCD2 0V COM2 VLCD VLCD1,VLCD2 0V COM3 VLCD VLCD1,VLCD2 0V LCD driver output when all LCD segments corresponding to COM1, COM2 and COM3 are turned off. VLCD VLCD1,VLCD2 0V LCD driver output when only LCD segments corresponding to COM1 are on VLCD VLCD1,VLCD2 0V LCD driver output when only LCD segments corresponding to COM2 are on. VLCD VLCD1,VLCD2 0V LCD driver output when LCD segments corresponding to COM1 and COM2 are on. VLCD VLCD1,VLCD2 0V LCD driver output when only LCD segments corresponding to COM3 are on. VLCD VLCD1,VLCD2 0V LCD driver output when LCD segments corresponding to COM1 and COM3 are on. VLCD VLCD1,VLCD2 0V LCD driver output when LCD segments corresponding to COM2 and COM3 are on. VLCD VLCD1,VLCD2 0V LCD driver output when all LCD segments corresponding to COM1, COM2 and COM3 are on. VLCD VLCD1,VLCD2 0V 1/3 Duty, 1/2 Bias Waveforms No. 6266-19/37 LC75804E, LC75804W 1/3 Duty, 1/3 Bias Drive Technique fosc 384 [Hz] COM1 VLCD VLCD1 VLCD2 0V COM2 VLCD VLCD1 VLCD2 0V COM3 VLCD VLCD1 VLCD2 0V LCD driver output when all LCD segments corresponding to COM1, COM2 and COM3 are turned off. VLCD VLCD1 VLCD2 0V LCD driver output when only LCD segments corresponding to COM1 are on. VLCD VLCD1 VLCD2 0V LCD driver output when only LCD segments corresponding to COM2 are on. VLCD VLCD1 VLCD2 0V LCD driver output when LCD segments corresponding to COM1 and COM2 are on. VLCD VLCD1 VLCD2 0V LCD driver output when only LCD segments corresponding to COM3 are on. VLCD VLCD1 VLCD2 0V LCD driver output when LCD segments corresponding to COM1 and COM3 are on. VLCD VLCD1 VLCD2 0V LCD driver output when LCD segments corresponding to COM2 and COM3 are on. VLCD VLCD1 VLCD2 0V LCD driver output when all LCD segments corresponding to COM1, COM2 and COM3 are on. VLCD VLCD1 VLCD2 0V 1/3 Duty, 1/3 Bias Waveforms No. 6266-20/37 LC75804E, LC75804W 1/4 Duty, 1/2 Bias Drive Technique fosc 384 [Hz] VLCD VLCD1,VLCD2 0V VLCD VLCD1,VLCD2 0V COM1 COM2 COM3 VLCD VLCD1,VLCD2 0V COM4 VLCD VLCD1,VLCD2 0V VLCD VLCD1,VLCD2 0V VLCD VLCD1,VLCD2 0V VLCD VLCD1,VLCD2 0V VLCD VLCD1,VLCD2 0V LCD driver output when all LCD segments corresponding to COM1, COM2, COM3 and COM4 are turned off. LCD driver output when only LCD segments corresponding to COM1 are on. LCD driver output when only LCD segments corresponding to COM2 are on. LCD driver output when LCD segments corresponding to COM1 and COM2 are on. LCD driver output when only LCD segments corresponding to COM3 are on. VLCD VLCD1,VLCD2 0V LCD driver output when LCD segments corresponding to COM1 and COM3 are on. VLCD VLCD1,VLCD2 0V VLCD VLCD1,VLCD2 0V VLCD VLCD1,VLCD2 0V VLCD VLCD1,VLCD2 0V VLCD VLCD1,VLCD2 0V LCD driver output when LCD segments corresponding to COM2 and COM3 are on. LCD driver output when LCD segments corresponding to COM1, COM2 and COM3 are on. LCD driver output when only LCD segments corresponding to COM4 are on. LCD driver output when LCD segments corresponding to COM2 and COM4 are on. VLCD VLCD1,VLCD2 0V LCD driver output when all LCD segments corresponding to COM1, COM2, COM3 and COM4 are on. 1/4 Duty, 1/2 Bias Waveforms No. 6266-21/37 LC75804E, LC75804W 1/4 Duty, 1/3 Bias Drive Technique fosc 384 [Hz] VLCD VLCD1 VLCD2 0V VLCD VLCD1 VLCD2 0V VLCD VLCD1 VLCD2 0V VLCD VLCD1 VLCD2 0V VLCD VLCD1 VLCD2 0V VLCD VLCD1 VLCD2 0V VLCD VLCD1 VLCD2 0V VLCD VLCD1 VLCD2 0V VLCD VLCD1 VLCD2 0V VLCD VLCD1 VLCD2 0V VLCD VLCD1 VLCD2 0V VLCD VLCD1 VLCD2 0V VLCD VLCD1 VLCD2 0V VLCD VLCD1 VLCD2 0V VLCD VLCD1 VLCD2 0V COM1 COM2 COM3 COM4 LCD driver output when all LCD segments corresponding to COM1, COM2, COM3 and COM4 are turned off. LCD driver output when only LCD segments corresponding to COM1 are on. LCD driver output when only LCD segments corresponding to COM2 are on. LCD driver output when LCD segments corresponding to COM1 and COM2 are on. LCD driver output when only LCD segments corresponding to COM3 are on. LCD driver output when LCD segments corresponding to COM1 and COM3 are on. LCD driver output when LCD segments corresponding to COM2 and COM3 are on. LCD driver output when LCD segments corresponding to COM1, COM2 and COM3 are on. LCD driver output when only LCD segments corresponding to COM4 are on. LCD driver output when LCD segments corresponding to COM2 and COM4 are on. LCD driver output when all LCD segments corresponding to COM1, COM2, COM3 and COM4 are on. 1/4 Duty, 1/3 Bias Waveforms No. 6266-22/37 LC75804E, LC75804W Voltage Detection Type Reset Circuit (VDET) This circuit generates an output signal and resets the system when logic block power is first applied and when the voltage drops, i.e., when the logic block power supply voltage is less than or equal to the power down detection voltage VDET, which is 3.0V, typical. To assure that this function operates reliably, a capacitor must be added to the logic block power supply line so that the logic block power supply voltage VDD rise time when the logic block power is first applied and the logic block power supply voltage VDD fall time when the voltage drops are both at least 1 ms. (See Figure 3 and Figure 4.) Power Supply Sequence The following sequences must be observed when power is turned on and off. (See Figure 3 and Figure 4.) • Power on :Logic block power supply(VDD) on → LCD driver block power supply(VLCD) on • Power off:LCD driver block power supply(VLCD) off → Logic block power supply(VDD) off However, if the logic and LCD driver block use a shared power supply, then the power supplies can be turned on and off at the same time. System Reset The LC75804E/W supports the reset methods described below. When a system reset is applied, display is turned off, key scanning is stopped, and all the key data is reset to low. When the reset is cleared, display is turned on and key scanning become possible. 1. Reset methods (1) Reset at power-on and power-down If at least 1 ms is assured as the logic block supply voltage VDD rise time when logic block power is applied, a system reset will be applied by the VDET output signal when the logic block supply voltage is brought up. If at least 1 ms is assured as the logic block supply voltage VDD fall time when logic block power drops, a system reset will be applied in the same manner by the VDET output signal when the supply voltage is lowered. Note that the reset is cleared at the point when all the serial data (1/3 duty: the display data D1 to D228 and the control data, 1/4 duty: the display data D1 to D300 and the control data) has been transferred, i.e., on the fall of the CE signal on the transfer of the last direction data, after all the direction data has been transferred. However, the above operations will be performed regardless of the state (high or low) of the RES pin. If RES is high, the reset will be cleared at the point the above operations are completed. On the other hand, if RES is low, the system will remain in the reset period as long as RES is not set high, even if the above operations are completed. (See Figure 3 and Figure 4.) No. 6266-23/37 LC75804E, LC75804W • 1/3 duty t1 t2 t3 t4 VDD VDET VDET VLCD CE Internal data D1 to D78 S0, S1, K0, K1 P0 to P3, SC, DR, DT VIL Display and control data transfer Undefined Defined Undefined Internal data (D79 to D153) Undefined Defined Undefined Internal data (D154 to D228) Undefined Defined Undefined System reset period Note: t1 ≥ 1 [ms] (Logic block power supply voltage VDD rise time) t2 ≥ 0 t3 ≥ 0 t4 ≥ 1 [ms] (Logic block power supply voltage VDD fall time) Figure 3 • 1/4 duty t1 t2 t3 t4 VDD VDET VDET VLCD CE Internal data D1 to D76 S0, S1, K0, K1 P0 to P3, SC, DR, DT VIL Display and control data transfer Undefined Defined Undefined Internal data (D77 to D152) Undefined Defined Undefined Internal data (D153 to D228) Undefined Defined Undefined Internal data (D229 to D300) Undefined Defined Undefined System reset period Note: t1 ≥ 1 [ms] (Logic block power supply voltage VDD rise time) t2 ≥ 0 t3 ≥ 0 t4 ≥ 1 [ms] (Logic block power supply voltage VDD fall time) Figure 4 No. 6266-24/37 LC75804E, LC75804W (2) Reset when the logic block power supply voltage is in the allowable operating range (VDD = 4.5 to 6.0V) The system is reset when the RES pin is set low, and the reset is cleared by setting RES pin high. 2. LC75804E/W internal block states during the reset period • CLOCK GENERATOR Reset is applied and the base clock is stopped. However, the OSC pin state (normal or sleep mode) is determined after the S0 and S1 control data bits are transferred. • COMMON DRIVER, SEGMENT DRIVER & LATCH Reset is applied and the display is turned off. However, display data can be input to the latch circuit in this state. • KEY SCAN Reset is applied, the circuit is set to the initial state, and at the same time the key scan operation is disabled. • KEY BUFFER Reset is applied and all the key data is set to low. • CCB INTERFACE, CONTROL REGISTER, SHIFT REGISTER Since serial data transfer is possible, these circuits are not reset. No. 6266-25/37 S1/P1 S2/P2 S9 S8/P8 S73 COM1 COM2 COM3 COM4/S74 LC75804E, LC75804W VLCD SEGMENT DRIVER & LATCH VLCD1 COMMON DRIVER VLCD2 SHIFT REGISTER VSS TEST CLOCK GENERATOR OSC CONTROL REGISTER DO CCB INTERFACE DI CL CE KEY BUFFER VDD VDET KS6 KS5 KS4 KS3 S76/KS2 S75/KS1 KI5 KI4 KI3 KI2 KI1 RES KEY SCAN Blocks that are reset 3. Output pin states during the reset period Output pin State during reset S1/P1 to S8/P8 L *5 S9 to S73 L COM1 to COM3 L COM4/S74 L *6 KS1/S75, KS2/S76 L *5 KS3 to KS5 X *7 KS6 H DO H *8 X: don’t care Notes:*5. These output pins are forcibly set to the segment output function and held low. *6. When power is first applied, this output pin is forcibly set to the common output function and held low. However, when the DT control data bit is transferred, either the common output or the segment output function is selected. *7. When power is first applied, these output pins are undefined until the S0 and S1 control data bits have been transferred. *8. Since this output pin is an open-drain output, a pull-up resistor of between 1 and 10 kΩ is required. This pin remains high during the reset period even if a key data read operation is performed. No. 6266-26/37 LC75804E, LC75804W Sample Application Circuit 1 1/3 duty, 1/2 bias (for use with normal panels) (P1) (P2) (P8) VDD OSC *9 VSS TEST VLCD +5.5V VLCD1 VLCD2 C ≥ 0.047 µF C RES *10 CE CL KKKKK DI DO I I I I I 54321 From the controller To the controller To the controller power supply COM1 COM2 COM3 P1/S1 P2/S2 P8/S8 S9 S73 COM4/S74 SS 77 65 / / KKKKKK SSSSSS 654321 Used with the backlight controller or other circuit. LCD panel (up to 228 segments) +5V (general-purpose output ports) (S75) (S76) *11 Key matrix (up to 30 keys) Notes:*9. Add a capacitor to the logic block power supply line so that the logic block power supply voltage VDD rise time when power is applied and the logic block power supply voltage VDD fall time when power drops are both at least 1 ms, as the LC75804E/W is reset by the VDET. *10. If the RES pin is not used for system reset, it must be connected to the logic block power supply VDD. *11. The DO pin, being an open-drain output, requires a pull-up resistor. Select a resistance (between 1 to 10 kΩ) appropriate for the capacitance of the external wiring so that signal waveforms are not degraded. No. 6266-27/37 LC75804E, LC75804W Sample Application Circuit 2 1/3 duty, 1/2 bias (for use with large panels) (P1) (P2) (P8) VDD OSC *9 10 kΩ ≥ R ≥ 1 kΩ C ≥ 0.047 µF VSS TEST VLCD +5.5V R C R VLCD1 To the controller P8/S8 S9 VLCD2 S73 COM4/S74 RES *10 CE CL KKKKK DI DO I I I I I 54321 From the controller To the controller power supply COM1 COM2 COM3 P1/S1 P2/S2 SS 77 65 / / KKKKKK SSSSSS 654321 Used with the backlight controller or other circuit. LCD panel (up to 228 segments) +5V (general-purpose output ports) (S75) (S76) *11 Key matrix (up to 30 keys) Notes:*9. Add a capacitor to the logic block power supply line so that the logic block power supply voltage VDD rise time when power is applied and the logic block power supply voltage VDD fall time when power drops are both at least 1 ms, as the LC75804E/W is reset by the VDET. *10. If the RES pin is not used for system reset, it must be connected to the logic block power supply VDD. *11. The DO pin, being an open-drain output, requires a pull-up resistor. Select a resistance (between 1 to 10 kΩ) appropriate for the capacitance of the external wiring so that signal waveforms are not degraded. No. 6266-28/37 LC75804E, LC75804W Sample Application Circuit 3 1/3 duty, 1/3 bias (for use with normal panels) (P1) (P2) (P8) VDD OSC *9 VSS TEST VLCD +5.5V VLCD1 VLCD2 C ≥ 0.047 µF C C RES *10 CE CL KKKKK DI DO I I I I I 54321 From the controller To the controller To the controller power supply COM1 COM2 COM3 P1/S1 P2/S2 P8/S8 S9 S73 COM4/S74 SS 77 65 / / KKKKKK SSSSSS 654321 Used with the backlight controller or other circuit. LCD panel (up to 228 segments) +5V (general-purpose output ports) (S75) (S76) *11 Key matrix (up to 30 keys) Notes:*9. Add a capacitor to the logic block power supply line so that the logic block power supply voltage VDD rise time when power is applied and the logic block power supply voltage VDD fall time when power drops are both at least 1 ms, as the LC75804E/W is reset by the VDET. *10. If the RES pin is not used for system reset, it must be connected to the logic block power supply VDD. *11. The DO pin, being an open-drain output, requires a pull-up resistor. Select a resistance (between 1 to 10 kΩ) appropriate for the capacitance of the external wiring so that signal waveforms are not degraded. No. 6266-29/37 LC75804E, LC75804W Sample Application Circuit 4 1/3 duty, 1/3 bias (for use with large panels) (P1) (P2) (P8) VDD *9 10 kΩ ≥ R ≥ 1 kΩ C ≥ 0.047 µF VSS TEST +5.5V R R C C To the controller COM1 COM2 COM3 P1/S1 P2/S2 VLCD VLCD1 VLCD2 R RES *10 CE CL KKKKK DI DO I I I I I 54321 From the controller To the controller power supply OSC P8/S8 S9 S73 COM4/S74 SS 77 65 / / KKKKKK SSSSSS 654321 Used with the backlight controller or other circuit. LCD panel (up to 228 segments) +5V (general-purpose output ports) (S75) (S76) *11 Key matrix (up to 30 keys) Notes:*9. Add a capacitor to the logic block power supply line so that the logic block power supply voltage VDD rise time when power is applied and the logic block power supply voltage VDD fall time when power drops are both at least 1 ms, as the LC75804E/W is reset by the VDET. *10. If the RES pin is not used for system reset, it must be connected to the logic block power supply VDD. *11. The DO pin, being an open-drain output, requires a pull-up resistor. Select a resistance (between 1 to 10 kΩ) appropriate for the capacitance of the external wiring so that signal waveforms are not degraded. No. 6266-30/37 LC75804E, LC75804W Sample Application Circuit 5 1/4 duty, 1/2 bias (for use with normal panels) (P1) (P2) (P8) VDD OSC *9 VSS TEST VLCD +5.5V VLCD1 VLCD2 C ≥ 0.047 µF P8/S8 S9 C RES *10 CE CL KKKKK DI DO I I I I I 54321 From the controller To the controller To the controller power supply COM1 COM2 COM3 S74/COM4 P1/S1 P2/S2 S S S73 77 65 / / KKKKKK SSSSSS 654321 Used with the backlight controller or other circuit. LCD panel (up to 300 segments) +5V (general-purpose output ports) (S75) (S76) *11 Key matrix (up to 30 keys) Notes:*9. Add a capacitor to the logic block power supply line so that the logic block power supply voltage VDD rise time when power is applied and the logic block power supply voltage VDD fall time when power drops are both at least 1 ms, as the LC75804E/W is reset by the VDET. *10. If the RES pin is not used for system reset, it must be connected to the logic block power supply VDD. *11. The DO pin, being an open-drain output, requires a pull-up resistor. Select a resistance (between 1 to 10 kΩ) appropriate for the capacitance of the external wiring so that signal waveforms are not degraded. No. 6266-31/37 LC75804E, LC75804W Sample Application Circuit 6 1/4 duty, 1/2 bias (for use with large panels) (P1) (P2) (P8) VDD OSC *9 VSS TEST 10 kΩ ≥ R ≥ 1 kΩ C ≥ 0.047 µF VLCD +5.5V R C VLCD2 RES *10 CE CL KKKKK DI DO I I I I I 54321 From the controller To the controller To the controller power supply R VLCD1 COM1 COM2 COM3 S74/COM4 P1/S1 P2/S2 P8/S8 S9 S S S73 77 65 / / KKKKKK SSSSSS 654321 Used with the backlight controller or other circuit. LCD panel (up to 300 segments) +5V (general-purpose output ports) (S75) (S76) *11 Key matrix (up to 30 keys) Notes:*9. Add a capacitor to the logic block power supply line so that the logic block power supply voltage VDD rise time when power is applied and the logic block power supply voltage VDD fall time when power drops are both at least 1 ms, as the LC75804E/W is reset by the VDET. *10. If the RES pin is not used for system reset, it must be connected to the logic block power supply VDD. *11. The DO pin, being an open-drain output, requires a pull-up resistor. Select a resistance (between 1 to 10 kΩ) appropriate for the capacitance of the external wiring so that signal waveforms are not degraded. No. 6266-32/37 LC75804E, LC75804W Sample Application Circuit 7 1/4 duty, 1/3 bias (for use with normal panels) (P1) (P2) (P8) VDD OSC *9 VSS TEST +5.5V VLCD VLCD1 VLCD2 C ≥ 0.047 µF C To the controller To the controller power supply P8/S8 S9 C RES *10 CE CL KKKKK DI DO I I I I I 54321 From the controller COM1 COM2 COM3 S74/COM4 P1/S1 P2/S2 S S S73 77 65 / / KKKKKK SSSSSS 654321 Used with the backlight controller or other circuit. LCD panel (up to 300 segments) +5V (general-purpose output ports) (S75) (S76) *11 Key matrix (up to 30 keys) Notes:*9. Add a capacitor to the logic block power supply line so that the logic block power supply voltage VDD rise time when power is applied and the logic block power supply voltage VDD fall time when power drops are both at least 1 ms, as the LC75804E/W is reset by the VDET. *10. If the RES pin is not used for system reset, it must be connected to the logic block power supply VDD. *11. The DO pin, being an open-drain output, requires a pull-up resistor. Select a resistance (between 1 to 10 kΩ) appropriate for the capacitance of the external wiring so that signal waveforms are not degraded. No. 6266-33/37 LC75804E, LC75804W Sample Application Circuit 8 1/4 duty, 1/3 bias (for use with large panels) (P1) (P2) (P8) OSC COM1 COM2 COM3 S74/COM4 P1/S1 P2/S2 *9 10 kΩ ≥ R ≥ 1 kΩ C ≥ 0.047 µF VSS TEST +5.5V VLCD R VLCD1 P8/S8 S9 R C VLCD2 R RES *10 CE CL KKKKK DI DO I I I I I 54321 From the controller To the controller To the controller power supply C S S S73 77 65 / / KKKKKK SSSSSS 654321 Used with the backlight controller or other circuit. LCD panel (up to 300 segments) VDD +5V (general-purpose output ports) (S75) (S76) *11 Key matrix (up to 30 keys) Notes:*9. Add a capacitor to the logic block power supply line so that the logic block power supply voltage VDD rise time when power is applied and the logic block power supply voltage VDD fall time when power drops are both at least 1 ms, as the LC75804E/W is reset by the VDET. *10. If the RES pin is not used for system reset, it must be connected to the logic block power supply VDD. *11. The DO pin, being an open-drain output, requires a pull-up resistor. Select a resistance (between 1 to 10 kΩ) appropriate for the capacitance of the external wiring so that signal waveforms are not degraded. Notes on transferring display data from the controller When using the LC75804E/W in 1/3 duty, applications transfer the display data (D1 to D228) in three operations, and in 1/4 duty, they transfer the display data (D1 to D300) in four operations. In either case, applications should transfer all of the display data within 30 ms to maintain the quality of the displayed image. No. 6266-34/37 LC75804E, LC75804W Notes on the controller key data read techniques 1. Timer based key data acquisition (1) Flowchart CE = [L] NO DO = [L] YES Key data read processing (2) Timing chart Key on Key on Key input Key scan t5 t6 t5 t5 CE t8 t8 t8 Key address DI t7 Key data read t7 t7 DO Key data read request t9 Controller determination (Key on) t9 Controller determination (Key on) t9 Controller determination (Key off) t9 Controller determination (Key on) Controller determination (Key off) t5: Key scan execution time when the key data agreed for two key scans. (615T(s)) t6: Key scan execution time when the key data did not agree for two key scans and the key scan was executed again. (1230T(s)) t7: Key address (43H) transfer time 1 T = ——— t8: Key data read time fosc (3) Explanation In this technique, the controller uses a timer to determine key on/off states and read the key data. The controller must check the DO state when CE is low every t9 period without fail. If DO is low, the controller recognizes that a key has been pressed and executes the key data read operation. The period t9 in this technique must satisfy the following condition. t9>t6+t7+t8 If a key data read operation is executed when DO is high, the read key data (KD1 to KD30) and sleep acknowledge data (SA) will be invalid. No. 6266-35/37 LC75804E, LC75804W 2. Interrupt based key data acquisition (1) Flowchart CE = [L] NO DO = [L] YES Key data read processing Wait for at least t10 CE = [L] NO DO = [H] YES Key OFF (2) Timing chart Key on Key on Key input Key scan t5 t5 t6 t5 CE t8 t8 t8 t8 Key address DI t7 Key data read t7 t7 t7 DO Key data read request t10 Controller determination (Key on) Controller determination (Key off) t10 Controller determination (Key on) Controller determination (Key on) t10 Controller determination (Key on) t10 Controller determination (Key off) t5: Key scan execution time when the key data agreed for two key scans. (615T(s)) t6: Key scan execution time when the key data did not agree for two key scans and the key scan was executed again. (1230T(s)) t7: Key address (43H) transfer time 1 T = ——— t8: Key data read time fosc No. 6266-36/37 LC75804E, LC75804W (3) Explanation In this technique, the controller uses interrupts to determine key on/off states and read the key data. The controller must check the DO state when CE is low. If DO is low, the controller recognizes that a key has been pressed and executes the key data read operation. After that the next key on/off determination is performed after the time t10 has elapsed by checking the DO state when CE is low and reading the key data. The period t10 in this technique must satisfy the following condition. t10 > t6 If a key data read operation is executed when DO is high, the read key data (KD1 to KD30) and sleep acknowledge data (SA) will be invalid. Specifications of any and all SANYO products described or contained herein stipulate the performance, characteristics, and functions of the described products in the independent state, and are not guarantees of the performance, characteristics, and functions of the described products as mounted in the customer’s products or equipment. To verify symptoms and states that cannot be evaluated in an independent device, the customer should always evaluate and test devices mounted in the customer’s products or equipment. SANYO Electric Co., Ltd. strives to supply high-quality high-reliability products. However, any and all semiconductor products fail with some probability. It is possible that these probabilistic failures could give rise to accidents or events that could endanger human lives, that could give rise to smoke or fire, or that could cause damage to other property. When designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective circuits and error prevention circuits for safe design, redundant design, and structural design. In the event that any or all SANYO products (including technical data, services) described or contained herein are controlled under any of applicable local export control laws and regulations, such products must not be exported without obtaining the export license from the authorities concerned in accordance with the above law. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise, without the prior written permission of SANYO Electric Co., Ltd. Any and all information described or contained herein are subject to change without notice due to product/technology improvement, etc. When designing equipment, refer to the “Delivery Specification” for the SANYO product that you intend to use. Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed for volume production. SANYO believes information herein is accurate and reliable, but no guarantees are made or implied regarding its use or any infringements of intellectual property rights or other rights of third parties. This catalog provides information as of May, 2003. Specifications and information herein are subject to change without notice. PS No. 6266-37/37