Ordering number : EN4817A CMOS LSI LC78211, 78212, 78213 Analog Function Switch Applications Package Dimensions Function switching under serial data control in amplifiers, receivers, and other electronic equipment unit: mm 3061-DIP30S Features [LC78211, 78212, 78213] • Two sets of eight (or in the LC78213, seven) built-in circuits with three switching configurations available based on differing internal connections • Control according to serial data sent from a microprocessor, and easy connection to 5 V microprocessors • Two identical products can be connected to a shared bus due to the provision of a select pin (S). • A reset pin that turns off all analog switches • A ±20 V withstand voltage rating allows these products to provide a wide dynamic range. SANYO: DIP30S Specifications Absolute Maximum Ratings at Ta = 25°C Parameter Maximum supply voltage Maximum input voltage Analog switch potential difference when on Allowable power dissipation Symbol Conditions Ratings Unit VDD max VDD –0.3 to +20 V VEE max VEE –20 to +0.3 V V I1 DI, CL, CE, S, RES –0.3 to +20 V V I2 L1 to L8, R1 to R8, LCOM1 to LCOM4, RCOM1 to RCOM4 VEE – 0.3 to VDD + 0.3 V ∆VON Pd max With the switch on 0.5 V Ta ≤ 75°C 100 mW Operating temperature range Topr –30 to +75 °C Storage temperature range Tstg –40 to +125 °C SANYO Electric Co.,Ltd. Semiconductor Bussiness Headquarters TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110 JAPAN 73096HA (OT)/72994 TH (OT) No. 4817-1/6 LC78211, 78212, 78213 Pin Assignments Top view Allowable Operating Ranges at Ta = 25°C, VSS = 0 V, | VDD | ≥ | VEE | Parameter Maximum supply voltage Symbol Conditions min typ max Unit VDD VDD – VEE ≥ 12 V: VDD 6.0 18.5 V VEE VDD – VEE ≥ 12 V: VEE –18.5 0 V VIH1 DI, CL, CE V VIH2 S, RES VIL1 4.0 18.5 0.7 VDD VDD V DI, CL, CE 0 0.7 V VIL2 S, RES 0 0.3 VDD V VIN L1 to L8, R1 to R8, LCOM1 to LCOM4, RCOM1 to RCOM4 VEE VDD V Low level clock pulse width tøL CL 0.5 µs High level clock pulse width tøH CL 0.5 µs tset up CL, DI 0.5 µs t1* CL, CE 0.5 µs Input high level voltage Input low level voltage Analog switch input voltage range Setup time Minimum reset pulse width Hysteresis t2* CL, CE 0.5 µs t3* CL, CE 0.5 µs VDD ≥ 6 V: RES 1.0 µs CL, CE, DI 0.3 V twRES VH Note: * CE, CL and DI waveforms No. 4817-2/6 LC78211, 78212, 78213 Electrical Characteristics at Ta = 25°C, VSS = 0 V Parameter Symbol Conditions min typ max Unit RON1 I = 1 mA, VDD – VEE = 12 V: L1 to L8, R1 to R8, LCOM1 to LCOM4, RCOM1 to RCOM4 150 Ω RON2 I = 1 mA, VDD – VEE = 37 V: L1 to L8, R1 to R8, LCOM1 to LCOM4, RCOM1 to RCOM4 70 Ω THD1 VIN = 1 Vrms, f = 1 kHz, VDD – VEE = 37 V: L1 to L8, R1 to R8, LCOM1 to LCOM4, RCOM1 to RCOM4 THD2 VIN = 0.1 Vrms, f = 1 kHz, VDD – VEE = 37 V: L1 to L8, R1 to R8, LCOM1 to LCOM4, RCOM1 to RCOM4 Analog switch on resistance Total harmonic distortion 0.0015 0.01 % 0.01 0.05 % Feedthrough FTH VIN = 0 dBV, f = 10 kHz, VDD – VEE = 37 V: L1 to L8, R1 to R8, LCOM1 to LCOM4, RCOM1 to RCOM4 55 dB Crosstalk CT VIN = 0 dBV, f = 10 kHz, VDD – VEE = 37 V: L1 to L8, R1 to R8, LCOM1 to LCOM4, RCOM1 to RCOM4 75 dB Input high level current IIH VI = 18.5 V: DI, CL, CE, S, RES Input low level current IIL VI = 0 V: DI, CL, CE, S, RES –10 –10 Analog switch leakage current (off state) IOFF VI = VEE to VEE + 37 V: L1 to L8, R1 to R8, LCOM1 to LCOM4, RCOM1 to RCOM4 Current drain IDD VDD +10 µA µA +10 µA 1.0 mA Equivalent Circuit Block Diagrams Continued on next page. No. 4817-3/6 LC78211, 78212, 78213 Continued from preceding page. No. 4817-4/6 LC78211, 78212, 78213 Pin Functions Pin I/O Internal equivalent circuit VDD, VSS, VEE Pin function Power supply L1 to L8, R1 to R8, LCOM1 to LCOM4, RCOM1 to RCOM4 See the block diagram. CL, DI, CE Analog switch input and output Serial data input (Schmitt buffer) CL..............Clock input DI...............Data input CE .............Chip enable I Selection of one of two chips The address is set to the values shown in the table below according to the level input to the S pin. Product S I LC78211 LC78212 LC78213 RES Address S pin level A0 A1 A2 L 0 1 0 1 H 1 1 0 1 A3 L 0 0 1 1 H 1 0 1 1 L 0 1 1 1 H 1 1 1 1 Reset input The states of the analog switches are undefined when power is first applied. Setting this pin low will force all switches the off state. I Operation 1. Data Input Procedure The LC78211, LC78212 and LC78213 are controlled by inputting specified data to the CL, DI and CE pins. The input data consists of 12 bits, of which four bits are address and eight bits are data. Bits correspond to the L1 to L8 and R1 to R8 analog switches, and a value of one turns the corresponding switch on, and a value of zero turns it off. 0.........Off 1.........On The address is used when the chip is connected to a shared bus. The data (address) that must be transmitted depends on the S pin and the particular product as shown in the table below. Product LC78211 LC78212 LC78213 Address S pin level A0 A1 A2 L 0 1 0 1 H 1 1 0 1 A3 L 0 0 1 1 H 1 0 1 1 L 0 1 1 1 H 1 1 1 1 Note: The bit for switch eight in the LC78213 is a “don’t care” bit, that is it can be either 0 or 1 without affecting chip function. This is because the LC78213 has two sets of seven (not eight) circuits. No. 4817-5/6 LC78211, 78212, 78213 2. DI, CL and CE Timing Data is read in on the rising edge of CL and latched on the falling edge of CE. 3. Notes on the Reset Pin The states of the analog switches are undefined when power is first applied. However, it is possible to use the reset pin to force all switches to the off state by connecting an RC circuit to this pin. 4. Using a CCB Bus with Multiple ICs The LC78211, LC78212 and LC78213 retain their prior state until they receive data with a matching address. 5. Replacing Earlier Models Caution is required when replacing an LC7821N, LC7823N and LC7823N with an LC78211, LC78212 and LC78213, since the S pin threshold levels differ. 6. Handling of Unused Input Pins We recommend connecting any unused switch pin to VSS through a resistor of up to a few 100 kΩ to prevent damage from static electricity. ■ No products described or contained herein are intended for use in surgical implants, life-support systems, aerospace equipment, nuclear power control systems, vehicles, disaster/crime-prevention equipment and the like, the failure of which may directly or indirectly cause injury, death or property loss. ■ Anyone purchasing any products described or contained herein for an above-mentioned use shall: ① Accept full responsibility and indemnify and defend SANYO ELECTRIC CO., LTD., its affiliates, subsidiaries and distributors and all their officers and employees, jointly and severally, against any and all claims and litigation and all damages, cost and expenses associated with such use: ➁ Not impose any responsibility for any fault or negligence which may be cited in any such claim or litigation on SANYO ELECTRIC CO., LTD., its affiliates, subsidiaries and distributors or any of their officers and employees jointly or severally. ■ Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed for volume production. SANYO believes information herein is accurate and reliable, but no guarantees are made or implied regarding its use or any infringements of intellectual property rights or other rights of third parties. This catalog provides information as of July, 1996. Specifications and information herein are subject to change without notice. No. 4817-6/6