January 1999 USB100 Programmable Low-Cost USB Machine (PLUM) Single Chip Controller for Mouse, Trackball, Joystick and Gamepad Applications General Description Features The USB100 is a Low cost, fully customizable controller for USB HID-class pointing devices. It is in full compliance with REV 1.0 of the USB standard and implements the HID class specification for mice, trackballs, joysticks and gamepads. This device interprets the commands specified in the HID class document and provides appropriate responses from an On-Chip EEPROM. It also provides ability to customize the device according to individual needs of the designers. Programming utilities supplied with this device allow HID manufacturers to easily create the necessary data to be programmed into the device. ■ USB 1.0 standard compliant ■ Has the necessary on-chip transceivers ■ Support for 2D and 3D mice with 2, 3 or more buttons ■ Supports 3 potentiometer mechanisms for joysticks ■ Up to 16 buttons for digital gamepads ■ Choice of 18-pin and 24-pin packages ■ Choice of 2Kbit and 4Kbit EEPROM densities The device includes the necessary transceiver for USB operation and meets all of the active and standby current specifications for a bus-powered device. Block Diagram POWER USB COMMAND PROCESSOR (HID) TX-FIFO SERIAL INTERFACE ENGINE X C V R USB CABLE (D+, D-, POWER & GROUND) RX-FIFO STATE MACHINE EEPROM UP TO 3 ROLLER/ POTENTIOMETER MECHANISMS UP TO 16 BUTTONS Use "A Diagram Number" Style Sheet" USB100 rev.D © 1999 Fairchild Semiconductor Corporation 1 www.fairchildsemi.com USB100 Programmable Low-Cost USB Machine (PLUM) PRELIMINARY 24 Pin Package OSC1 OSC2 H4 B8/F RESET H3 H1 H2 V1 V2 O2 GND 18 Pin 3D Package OSC2 H4 F RESET H3 H1 H2 V1 V2 VDD B6 USBD+ USBDGND B7 B5 B1 B2 B3 B4 O1 OSC1 VDD USBD+ USBDGND B1 B2 B3 O1 Pin Description Pin Type Description H4 I Roller/Button/Joystick input. H3 I Roller/Button/Joystick input. O2 I/O OSC1 I Crystal input number 1. Register output pin / Button input. OSC2 I Crystal input number 2 B4 I Button input Reset I Active high reset pin H1 I Roller/Button/Joystick input. H2 I Roller/Button/Joystick input. V1 I Roller/Button/Joystick input. V2 I Roller/Button/Joystick input. GND I Ground B7 I Button input B6 I Button input B5 I Button input VDD I Positive power supply USBD+ O USB D + line USBD- O USB D – line GND I Ground B8/F I/O B1/CS I Button input / LED driver Button input and chip select to internal EEPROM.* B2/SK I Button input and system clock to internal EEPROM.* B3/DI I Button input and data in to internal EEPROM.* O1/DO O Button input and data out to read from internal EEPROM.* * See Programming internal EEPROM section USB100 rev.D 2 www.fairchildsemi.com USB100 Programmable Low-Cost USB Machine (PLUM) Pinout Operating Conditions Ambient Storage Temperatures -65°C to + 150°C Ambient Operating Temperature All Input or Output Voltages with respect to ground VCC + 1 to – 0.3V Power Supply (VCC) Range Lead Temperature (Soldering, 10 seconds) +300% ESD Rating 2000V 0°C to +70°C 4.4V to 5.5V DC and AC Electrical Characteristics 4.4V ≤ VCC ≤ 5.5V Symbol Parameter Conditions Min Max Units ICCA Operating Current USB interface in active mode 40 mA ICCS Standby Current USB interface in suspend 500 µA VIL Input Low Voltage VIH Input High Voltage VOL Output Low Voltage VOH Output High Voltage 0.8 2 V V 0.4 2.4 V V IIL Input Leakage Current 2.5 µA IOL Output Leakage Current 2.5 µA 1 MHz FSK SK Clock Frequency TSKH SK High Time Note 3 250 0 ns TSKL SK Low Time 250 ns TCS Minimum CS Low Time 250 ns TCSS CS Setup Time 50 ns TDH DO Hold Time 70 ns Note 4 TDIS DI Setup Time 100 ns TCSH CS Hold Time 0 ns TDIH DI Hold Time 20 ns TPD1 Output Delay to “1” 500 ns TPD0 Output Delay to “0” 500 ns TSY CS to Status Valid 500 ns TDF CS to DO in TRI-STATE 100 ns TWP Write Cycle Time 10 ms AC Test Conditions Output Load Input Pulse Levels Timing Measurements Reference Level 1 TTL Gate Input 0.4V and 2.4V Output 1V and 2V 0.8V and 2.0V Note 1: Stress ratings above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and operation of the device at these or any other conditions above those indicated in the operational sections of the specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Note 2: The shortest allowable S clock period = 1/fSK (as shown under the fSK parameter). Maximum SK clock speed (minimum SK period) is determined by the interaction of several AC parameters stated in the datasheet. Within this SK period, both tSKH and tSKL limits must be observed. Therefore, it is not allowable to set 1/fSK = tSKH(minimum) + tSKL(minimum) for shorter SK cycle time operation. Note 3: CS (Chip Select) must be brought low (to VIL) for an interval of tCS in order to reset all internal device registers (device reset) prior to beginning another opcode cycle. (This is shown in the opcode diagrams in the following pages.) USB100 rev.D 3 www.fairchildsemi.com USB100 Programmable Low-Cost USB Machine (PLUM) Absolute Maximum Ratings O1, O2 Functionality. ICB register 1[3:2] H1, H2, H3, H4, V1, V2 (Roller/Joystick inputs) IOM[1:0] Function When configured as roller inputs these pins function in pairs, H1 and H2, H3 and H4, V1 and V2 to allow photo diodes to be attached in a mouse or trackball application. See the section “Roller Movement Reporting” for a more detailed description. When configured for a joystick only one of the inputs pairs is used. A potentiometer is attached to track the movements of a joystick lever. When these inputs are configured as buttons they all act independently as active low button inputs. All of them have internal pull-ups and debounce circuitry which can be programmed using the ICB registers. These inputs also contain current sink features so no external resistor is needed to sink current from the photo diode. 00 Both O1 and O2 function as programmable outputs. 01 O1 is a programmable output but O2 is a standard button input. 11 Both O1 and O2 are standard inputs. In case these are selected as outputs, their state (1 or 0) can be set using the USB set_report command. These outputs are opencollector. A typical use of these outputs is using them to drive LEDs (for example, a drag-lock function in a trackball). These pins have a programmable current sink capability. B1, B2, B3, B4, B5, B6, B7, B8/F (Button inputs) B8/F The button inputs to the USB100 have internal pull up resistors, with active low inputs to the chip. These inputs also contain debounce circuitry which can be programmed by the ICB registers. When this pin is configured as an input it will behave as a standard button input. But if the pin is disabled in the ICB registers then this pin can be used to control the roller LEDS in powersave mode. Using the B8/F pin to control the LEDs Key Debounce Select Table (ICB register3[3:2]) VDD KD[1:0] 00 15 ms 01 30 ms 10 45 ms 11 60 ms USB100 F USBD -, USBD + This allows the LEDs to be shut off during powersave mode which allows the USB100 to draw very little current. The official name for powersave mode on a USB device is known as suspend mode which is discussed in the section labeled Suspend Mode Operation. These inputs are the serial bus lines which USB data is communicated. These bi – directional lines connect to the host, through a USB type A or type B connector, and are used to communicate all USB information to and from the host. The two lines must both be wired through a 27 ohm resistor before being attached to the USB connector. See Recommended Configuration for a detailed diagram. OSC1, OSC2 These two pins are the clock inputs into the USB100. The speed at which the chip runs at is 6MHz. The clock sign can be generated two ways. The first is to use a parallel resonant, fundamental mode crystal circuit or a ceramic resonator circuit connected to the OSC1 and OSC2 inputs. The other method is to use a crystal oscillator connected to the OSC2 input and leaving the OSC1 input unconnected Reset This pin is used to reset the entire chip. It must be held high for more than 10ns, to reset the chip and then brought low for the reset of normal chip operation. O1, O2 USB modes of operation These two pins are wired to internal registers which can be programmed with either a “1” or a “0” by a USB request. If this command is sent to the USB100. INSERT COMMAND FROM INSPECTOR. Then the O1 and O2 pins will be programmed with the values that are in the second data package. These two pins can also be configured as standard button inputs by one of the ICB registers. USB100 rev.D The USB100 loads up its configuration from the EEPROM on power-on reset, or when a USB reset command is issued. Upon completion of reset, the device is in a operational mode, and responds correctly to the various commands described in the USB spec rev 1.0. The USB100 supports two endpoints – the default endpoint (endpoint 0) and the interrupt endpoint (endpoint 1). The supported packet size on both endpoints is 8 bytes. The endpoint 1 is an “IN” endpoint. 4 www.fairchildsemi.com USB100 Programmable Low-Cost USB Machine (PLUM) Interface Pin Descriptions IS[3:0] Current The USB100 supports all of the required standard requests. These requests are sent to the device using control transfers to endpoint 0. 0000 0.1 mA 0001 0.2 mA In USB terminology, the data transmitted by the mouse when movement is detected is called a report. The reports are generated by the USB100 device in accordance to the USB HID spec 1.0 Final. 0010 0.3 mA 0011 0.4 mA 0100 0.5 mA Programming the EEPROM 0101 0.6 mA 0110 0.7 mA 0111 0.8 mA 1000 0.9mA 1001 1.0mA The on-chip EEPROM can be programmed in a special mode which defines some of the button inputs/output as a microwire port.. In this mode, these inputs behave as a conventional Microwire serial port. Data can be easily programmed and verified, by executing simple EEPROM programming commands. Initial Configuration Bytes (ICB) register description Input Pin Configuration Byte 0 (ICB0) (Address 1) The first five bytes in the EEPROM are used to configure the physical characteristics of the USB100 device, and are called the Initial configuration Byte registers. Some of the bits in these registers are reserved, and are referred to as RFU (reserved for future use) in the following section. D6 D5 D4 IS3 IS2 IS1 IS0 D3 D2 IOM1 IOM0 D6 D5 D4 D3 D2 D1 D0 B8 B7 B6 B5 B4 B3 B2 B1 B[7:0]: Input Pin Report Generator. A ‘1’ causes this bit to be reported in the corresponding report generated when the device is polled for the status. The device accepts only the following bit patterns as valid. B[7:0] control the functionality for pin inputs B[8:1] respectively. Roller Configuration Byte (Address 0) D7 D7 D1 D0 00000000 R1 R0 00000001 R[1:0]: No of roller pairs. This pair of bits configure the functionality of the three roller pair inputs – <H1, H2>, <V1,V2> and <H3, H4>. 00000011 00: No rollers on this device, all roller inputs are available as general purpose inputs 00011111 01: H1, H2 are the only roller mechanism active. The other roller inputs are available as general purpose inputs. 01111111 00000111 00001111 00111111 11111111 10: H1, H2 and V1 and V2 are defined as roller mechanism pairs. The other pair is still available as general purpose inputs. Input Pin Configuration Byte 1 (ICB1) (Address 2) 11: All the three pairs of roller inputs function as roller inputs. It must be noted that the reassignment of the rollers must be done only as follows: If the application needs to use only one roller – use H1 and H2. Two rollers – use H1, H2 and V1, V2, Three rollers – use H1, H2, V1, V2 and H3, H4. Any other choice for roller use is illegal and results in unpredictable device behavior. D7 D6 D5 D4 D3 D2 D1 D0 IO1 IO0 EB5 EB4 EB3 EB2 EB1 EB0 EB[5:0]: Input Pin Report Generator, Extended byte. The functionality of this register is influenced by the roller configuration byte. A ‘1’ causes this bit to be reported in the corresponding report generated when the device is polled for the status. EB0 corresponds to H3 and EB1 corresponds to H4. EB2 corresponds to V1 and EB3 corresponds to V2. EB4 corresponds to H1 and EB5 corresponds to H2. IOM[1:0]: I/O functionality of the O0 and O1 pins. When IOM0 is set to ‘0’, the O0 bit functions as an output. When set to ‘1’ it becomes an input. . When IOM1 is set to ‘0’, the O1 bit functions as an output. When set to ‘1’ it becomes an input. The only valid combinations for these bits are 00, 01 and 11 respectively. 00000000 00000001 00000011 IS[3:0]: This 4-bit value is to set the amount of current that an external device can sink into the H1, H2, V1, V2 and H3 and H4 inputs When these bits are set to 0000 the current sink is set to 0.1 mA on each of the inputs. In can be varied in steps of 0.1mA up to a max of 1 mA. USB100 rev.D 00000111 00001111 00011111 00111111 5 www.fairchildsemi.com USB100 Programmable Low-Cost USB Machine (PLUM) Standard Requests Descriptor Setup IO[1:0]: When the IO pins are reconfigured as inputs, a ‘1’ in the corresponding bit position will cause the input to be included in the report generator. The EEPROM stores a Descriptor Description Table (DDT) followed by the actual descriptors (DES). The DDT begins at byte address 8 in the EEPROM. It consists of 14 Words. Each Word consists of two bytes – The first byte is a byte indicating the type of descriptor (these byte values are indicated in the USB specification). The second byte is an address. This address indicates the first byte of this descriptor in the EEPROM. An unimplemented descriptor table entry begins with a 00. The following table shows a possible configuration. Application Configuration Byte (Address 3) D7 D6 D5 D4 D3 D2 D1 D0 FIS3 FIS2 FIS1 FIS0 KD1 KD0 F1 F0 F[1:0]: Function Select. Selects between the following Address Map 00 : Mouse operation Memory AddressRange 01: RFU 10: Joystick Operation. Data type 08-35 Descriptor Description Table 36-53 Device Descriptor 54-62 Config Descriptor 63-71 Interface Descriptor 10: 45 Ms 72-78 Mouse HID Class Descriptor 11: 60 Ms 79-86 Endpoint Descriptor 87-118 String Descriptor 11: Digital Gamepad operation KD[1:0]: Key Debounce Select: 00: 15 Ms 01: 30 Ms FIS[3:0]: These bits select the amount of current that the ‘F’ pin can sink, in 1 mA increments. When FIS[3:0] = “0000” The current sink is set at 2 mA. Incrementing this count by 1 will cause the current to be increased by 1mA The maximum value is 10 mA. Descriptor Description Table (for above example) Remote Resume Config Byte (Address 4) D7 D6 D5 D4 RFU RFU RFU RFU D3 D2 D1 D0 Address Descriptor type Memory Offset 08 Device 36 10 Config 54 12 Interface 63 14 Mouse-HID 72 16 Endpoint 78 18 String 87 20 00 00 22 00 00 24 00 00 26 00 00 28 00 00 30 00 00 011: 60 ms 32 00 00 100: 75 ms 34 00 00 RRES RRES RRES RRES _EN 2 1 0 RRES_EN: Remote_resume enable. This bit, when set, enables remote resume operation. RRES[2:0]: Duration Select. When the device has entered in suspend mode, these bits select the duration after which an internal “momentary wakeup” is done to check whether there has been any movement on the rollers in the mouse mode or the potentiometers in the joystick mode. The RRES_EN bit must be set to 1 to enable this feature. 000: 15 ms 001: 30 ms 010: 45 ms 101: 90 ms Roller Movement Reporting 110: 105 ms The roller mechanism built on the USB100 is capable of interfacing either to a LED-chopper wheel-Phototransistor system or a mechanical system using a commutator with wiper contacts. 111: Reserved for future use (do not use this combination, unpredictable operation could result) USB100 rev.D 6 www.fairchildsemi.com USB100 Programmable Low-Cost USB Machine (PLUM) RFU: Reserved for future use, must be set to 0. USB100 Programmable Low-Cost USB Machine (PLUM) H1 or V1 or H3 H2 or V2 or H4 Negative Counting H1 or V1 or H3 H2 or V2 or H4 Positive Counting v USB100 Q1 D1 Q2 H1 D2 H2 F Schematic 1: Roller Mode of Operation Hardware Features When the Roller configuration register is used to define an input pair as roller inputs, the corresponding roller movement reporting is enabled. In this case, internally, the roller wheel pulses are counted and registered into an 8 bit register. One register is available per input pair. A total of three rollers movement registers (RMRs) are available, corresponding to the three roller mechanisms available. On all the input pairs (H1, H2 or V1, V2 or H3, H4) the positive counting sequence is defined as (0,0), (0,1), (1,1) and (0,0) and the same sequence repeating over again. Negative counting sequence is defined as (0,0), (1,0), (1,1) and (0,1) and the same sequence repeating again. Each of the above transitions will result in the counter incrementing or decrementing by one depending on whether the rollers are moving in the positive or negative direction. Each time an IN query is sent on endpoint 1, the counter contents are transferred to a temporary holding register and queued for transmission on the USB. When an ACK is received for the current transaction, the counter is cleared. Roller / Potentiometer Interface One of the key differences between the mouse and joystick hardware implementation is that themouse uses optical encoding v P1 USB100 P2 H1 V1 Schematic 2 : Potentiometer Mode of Operation for Joystick USB100 rev.D 7 www.fairchildsemi.com Suspend mode operation When the PLUM device determines that the necessary conditions (laid down in the USB standard), it goes into the suspend mode. It wakes up on USB bus activity, or when any of the buttons are depressed. There exists an internal timer, whose timing operation could be selected via bits 3 through 0 in ICB register 5. The PLUM device wakes up on the expiration of the timer. It senses the roller/ potentiometer interface to determine if these inputs have changed since the last poll. It does a remote wakeup, when such a movement has occurred. to set the bits. In a mouse mode, the H1, H2, V1,V2 and H3 & H4 inputs are selected for the roller mechanism decode.In the joystick mode, it selects the potentiometer interface. The state machine uses a different algorithm for interpreting the inputs to the chip. This function selection also affects the format of the report that is generated.The roller mode is shown in schematic 1 and the potentiometer mode is shown in schematic 2. In case of the roller mode of operation (mouse/trackball), the transitions on the Hx and Vx pairs are used in the counting process to generate a digital estimate of the motion of the ball. In the joystick mode of operation, the RC timing constant changes the width of an internal digital pulse whose width is measured and reported back. All of the buttons feature an internal pullup. The actual switches used is a push button switch with one terminal connected to a button input and the second terminal connected to ground. Remote Wakeup Support This device supports the remote wakeup feature. This is indicated to the host via the corresponding descriptor. Internally, the state machine uses the values of the RRES_EN and RRES[2:0] bits in the Remote Resume configuration byte to enable this feature, and the amount of time between the “polls” to the roller/potentiometer ports to determine whether the necessary conditions for wakeup have been met. Crystal / Crystal Oscillator combination OSC1 OSC2 The above configuration is the recommended configuration for use with a crystal or a ceramic resonator. The capacitors are optional and if used, must be in the 10-30pf range. The resistor is necessary and its value is 1MΩ. A metal-can oscillator may be used too. In this case, the output of the oscillator must be connected to OSC1 and OSC2 must be left unconnected. Life Support Policy Fairchild's products are not authorized for use as critical components in life support devices or systems without the express written approval of the President of Fairchild Semiconductor Corporation. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform, when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. Fairchild Semiconductor Americas Customer Response Center Tel. 1-888-522-5372 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. Fairchild Semiconductor Europe Fax: +44 (0) 1793-856858 Deutsch Tel: +49 (0) 8141-6102-0 English Tel: +44 (0) 1793-856856 Français Tel: +33 (0) 1-6930-3696 Italiano Tel: +39 (0) 2-249111-1 Fairchild Semiconductor Hong Kong 8/F, Room 808, Empire Centre 68 Mody Road, Tsimshatsui East Kowloon. Hong Kong Tel; +852-2722-8338 Fax: +852-2722-8383 Fairchild Semiconductor Japan Ltd. 4F, Natsume Bldg. 2-18-6, Yushima, Bunkyo-ku Tokyo, 113-0034 Japan Tel: 81-3-3818-8840 Fax: 81-3-3818-8841 Fairchild does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and Fairchild reserves the right at any time without notice to change said circuitry and specifications. USB100 rev.D 8 www.fairchildsemi.com USB100 Programmable Low-Cost USB Machine (PLUM) and a roller wheel to detect mouse movement. In contrast, joystick uses a potentiometer to detect angular motion. The function select bits [F1:0] allow the designer