74VHCT05A HEX INVERTER (OPEN DRAIN) ■ ■ ■ ■ ■ ■ ■ ■ HIGH SPEED: tPD = 3.2 ns (TYP.) at VCC = 5V LOW POWER DISSIPATION: ICC = 2 µA (MAX.) at TA = 25 oC COMPATIBLE WITH TTL OUTPUTS: VIH = 2V (MIN), VIL = 0.8V (MAX) POWER DOWN PROTECTION ON INPUTS OPERATING VOLTAGE RANGE: VCC (OPR) = 4.5V to 5.5V PIN AND FUNCTION COMPATIBLE WITH 74 SERIES 05 IMPROVED LATCH-UP IMMUNITY LOW NOISE: VOLP = 0.8V (Max.) DESCRIPTION The 74VHCT05A is an advanced high-speed CMOS OPEN DRAIN HEX INVERTER fabricated with sub-micron silicon gate and double-layer metal wiring C2MOS technology. The internal circuit is composed of 3 stages including buffer output, which provides high noise immunity and stable output. M (Micro Package) T (TSSOP Package) ORDER CODES : 74VHCT05AM 74VHCT05AT Power down protection is provided on all inputs and 0 to 7V can be accepted on inputs with no regard to the supply voltage. This device can be used to interface 5V to 3V. All inputs and outputs are equipped with protection circuits against static discharge, giving them 2KV ESD immunity and transient excess voltage. PIN CONNECTION AND IEC LOGIC SYMBOLS August 1999 1/7 74VHCT05A INPUT EQUIVALENT CIRCUIT PIN DESCRIPTION PIN No SYMBOL 1, 3, 5, 9, 11, 13 1A to 6A Data Inputs NAME AND FUNCT ION 2, 4, 6, 8, 10, 12 1Y to 6Y Data Outputs 7 GND Ground (0V) 14 VCC Positive Supply Voltage TRUTH TABLE A Y L Z H L Z: High Impedance ABSOLUTE MAXIMUM RATINGS Symbol Value Unit Supply Voltage -0.5 to +7.0 V VI DC Input Voltage -0.5 to +7.0 V VO DC Output Voltage -0.5 to VCC + 0.5 V IIK DC Input Diode Current - 20 mA IOK DC Output Diode Current ± 20 mA IO DC Output Current 25 mA ± 50 mA VCC Parameter ICC or IGND DC VCC or Ground Current Tstg TL Storage Temperature Lead Temperature (10 sec) -65 to +150 o 300 o C C Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these condition is not implied. RECOMMENDED OPERATING CONDITIONS Symbol VCC Parameter Supply Voltage VI Input Voltage VO Output Voltage Top Operating Temperature dt/dv Input Rise and Fall Time (see note 1) (V CC = 5.0 ± 0.5V) 1) VIN from 0.8V to 2 V 2/7 Valu e Unit 4.5 to 5.5 V 0 to 5.5 V 0 to VCC -40 to +85 0 to 20 V o C ns/V 74VHCT05A DC SPECIFICATIONS Symb ol Parameter T est Cond ition s Min. 2 VIH High Level Input Voltage 4.5 to 5.5 VIL Low Level Input Voltage 4.5 to 5.5 VOL Low Level Output Voltage IOZ High Impedance Output Leakage Current Value T A = 25 o C V CC (V) Typ . Un it -40 to 85 o C Max. Min . Max. 2 0.8 V 0.8 V 4.5 I O=50 µA 0.1 0.1 4.5 IO=8 mA 0.36 0.44 VI = VIH or VIL VO = 0V to 5.5V ±0.25 ±2.5 µA 5.5 0 to 5.5 VI = 5.5V or GND 0.0 V ±0.1 ±1.0 µA ICC Quiescent Supply Current 5.5 VI = VCC or GND 2 20 µA ∆ICC Additional Worst Case Supply Current 5.5 One Input at 3.4V, other input at VCC or GND 1.35 1.5 mA II Input Leakage Current AC ELECTRICAL CHARACTERISTICS (Input t r = tf =3 ns) Symb ol tPZL tPLZ Parameter Test Co ndition V CC (*) CL (pF ) (V) Propagation Delay Time 5.0 15 Value T A = 25 o C Min. Typ . Max. 3.2 4.2 Un it 5.0 50 4.2 5.5 1.0 6.4 Propagation Delay Time 5.0 50 7.5 9.8 1.0 11.3 -40 to 85 o C Min . Max. 1.0 4.8 ns ns (*) Voltage range is 5V ± 0.5V CAPACITIVE CHARACTERISTICS Symb ol Parameter T est Cond ition s Value T A = 25 o C Min. Un it -40 to 85 o C Typ . Max. 10 Min . Max. Input Capacitance 4 COUT Output Capacitance 5 pF CPD Power Dissipation Capacitance (note 1) 6 pF C IN 10 pF 1) CPD isdefined as the value of the IC’sinternal equivalent capacitance which is calculated fromthe operating current consumption without load. (Referto Test Circuit).Average operating current can be obtained by the following equation. ICC(opr) = CPD • VCC • fIN + ICC/6 (per Gate) 3/7 74VHCT05A DYNAMIC SWITCHING CHARACTERISTICS Symb ol Parameter T est Cond ition s Dynamic Low Voltage Quiet Output (note 1, 2) 5.0 VIHD Dynamic High Voltage Input (note 1, 3) 5.0 VILD Dynamic Low Voltage Input (note 1, 3) 5.0 VOLP VOLV Value T A = 25 o C V CC (V) Min. -0.8 C L = 50 pF Un it -40 to 85 o C Typ . Max. 0.4 0.8 Min . Max. -0.4 2.0 V 0.8 1) Worst case package. 2) Max number of outputs defined as (n). Data inputs are driven 0V to 3.0, (n -1) outputs switching and one output atGND. 3) Max number of data inputs (n) switching. (n-1) switching 0V to3.0V. Inputs under test switching: 3.0V to threshold (VILD), 0V to threshold (VIHD), f=1MHz. TEST CIRCUIT CL = 15/50 pF or equivalent (includes jig and probe capacitance) RL = R1 = 1KΩ or equivalent RT = ZOUT of pulse generator (typically 50Ω) WAVEFORM: PROPAGATION DELAYS (f=1MHz; 50% duty cycle) 4/7 74VHCT05A SO-14 MECHANICAL DATA mm DIM. MIN. TYP. A a1 inch MAX. MIN. TYP. 1.75 0.1 0.068 0.2 a2 MAX. 0.003 0.007 1.65 0.064 b 0.35 0.46 0.013 0.018 b1 0.19 0.25 0.007 0.010 C 0.5 0.019 c1 45 (typ.) D 8.55 8.75 0.336 0.344 E 5.8 6.2 0.228 0.244 e 1.27 e3 0.050 7.62 0.300 F 3.8 4.0 0.149 0.157 G 4.6 5.3 0.181 0.208 L 0.5 1.27 0.019 0.050 M S 0.68 0.026 8 (max.) P013G 5/7 74VHCT05A TSSOP14 MECHANICAL DATA mm DIM. MIN. inch TYP. A MAX. MIN. MAX. 1.1 0.433 A1 0.05 0.10 0.15 0.002 0.004 0.006 A2 0.85 0.9 0.95 0.335 0.354 0.374 b 0.19 0.30 0.0075 0.0118 c 0.09 0.20 0.0035 0.0079 D 4.9 5 5.1 0.193 0.197 0.201 E 6.25 6.4 6.5 0.246 0.252 0.256 E1 4.3 4.4 4.48 0.169 0.173 0.176 e 0.65 BSC 0.0256 BSC K 0o 4o 8o 0o 4o 8o L 0.50 0.60 0.70 0.020 0.024 0.028 A A2 A1 b e K c E1 PIN 1 IDENTIFICATION 1 L E D 6/7 TYP. 74VHCT05A Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specification mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a trademark of STMicroelectronics 1999 STMicroelectronics – Printed in Italy – All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - Canada - China - France - Germany - Italy - Japan - Korea - Malaysia - Malta - Mexico - Morocco - The Netherlands Singapore - Spain - Sweden - Switzerland - Taiwan - Thailand - United Kingdom - U.S.A. http://www.st.com . 7/7