ESM1600B QUAD COMPARATOR INTERFACE CIRCUIT . .. .. MINIMUM HYSTERESIS VOLTAGE AT EACH INPUT : 0.3V OUTPUT CURRENT : 15 mA LARGE SUPPLY VOLTAGE RANGE : + 10V to + 35V INTERNAL THERMAL PROTECTION INPUT AND OUTPUT CLAMPING PROTECTION DIODES. DIP14 DESCRIPTION The ESM1600Bis a quadruplecomparatorintented to provide an interface between signal processing and transmitting lines in very noisy industrial surroundings. Outputof each comparator,used as line driver, supplies a constant current (PNP output stage) and is specially well protected against powerful overvoltages. The open collector output circuit allows the connectionof several comparators to a single transmitting line. The ESM1600B can operate as receiver on a line transmitting noisy high-voltage signals. Hysteresis effect, internally implemented on inputs of each comparator provides an excellent noise immunity. In addition, each input is also protected against overvoltages. SO16 ORDER ING NUMBERS: ESM1600B (DIP14) ESM1600BFP (SO16) The ESM1600B can operate in a wide supply voltage range (standard operational amplifier ± 15 V supply or single + 12 V or + 24 V supplies used in industrial electronic sets). Moreover, internal thermal protection circuitry cuts out the output current of the four comparatorswhen power dissipation becomes excessive. PIN CONNECTIONS (top view) DIP14 1 - Inverting input 1 2 - Non-inverting input 1 3 - Output 1 4 - Non-inverting input 2 5 - Inverting input 2 6 - Output 2 7 - GND 8 - Output 3 9 - Inverting input 3 10 - Non-inverting input 3 11 - Output 4 12 - Non-inverting input 4 13 - Inverting input 4 14 - VCC January 1997 SO16 1 - Inverting input 1 2 -Non-inverting input 1 3 - Output 1 4 - Non-inverting input 2 5 - Inverting input 2 6 - Output 2 7 - GND 8 - N.C. 9 - N.C. 10 - Output 3 11 - Inverting input 3 12 - Non-inverting input 3 13 - Output 4 14 - Non-inverting input 4 15 - Inverting input 4 16 - VCC 1/10 ESM1600B SCHEMATIC DIAGRAM ABSOLUTE MAXIMUM RATINGS Symbol Parameter Value Unit V VCC Supply Voltage 45 VID Differential Input Voltage 45 V VI Input Voltage –0.7 to +45 V mA Output Current Internally Limited Ptot Power Dissipation Internally Limited Top Operating Ambient Temperature Range IO (max) Tstg 2/10 Storage Temperature Range W –25 to +85 o –40 to +150 o C C ESM1600B ELECTRICAL CHARACTERISTICS VCC = +35V, -25oC ≤ Tamb ≤ +85oC (unless otherwise specified) Symbol Parameter Min. + VI VI – Input Voltage Range - Note 1 VC Input Control Voltage (2V < VCM < 33V) - Note 2 IIB Input Bias Current - Note 3 ISC Short-circuit Output Current VCC = +10 to +35 V VCC–VO Typ. Max. 0 2 33 33 150 500 1 5 6 1.5 IOL IOH Output Off-state Current (VI + = 2V, VI – = 33V) 1 5 ICC Supply Current R L = ∞ for the 4 Comparators R L Common for the 4 Comparators 3 9 5 12 SVO Output Slew-rate (R L = 3kΩ, Tamb = +25oC) VF Input Protective Diode Forward Voltage o (I = 20mA, Tamb = +25 C) 1.5 Energy of Pulses against which Circuit Output is Protected (Tamb = +25oC) - Note 4 20 Pulsed Current Applied to Protective Output Diodes (Tamb = +25oC) - Note 5 mV 1 µA mA 2 V 3 µA 4 mA 5 25 1 – Fig. V Non-inverting Input Inverting Input Output Saturation Voltage (high level) - (IO = –10mA) – Typ. 1 V/µs V mJ A 6 0.4 No tes : 1. When negative input is biased between 0 and 2 volts output is always low. 2. Comparator hysteresis voltage on positive input on the one hand and negative input on the other hand equals sum of input control voltages VC1 + VC2 or VC3 + VC4. 3. Input current flows out of the circuit owing to PNP input stage. This current is constant and independent of output level. So no load change is transmitted to inputs. 4. By definition, a circuit is immunized against powerful signals when no durable character istic change occurs after the application of these signals and when the circuit has not been destroyed. In industrial surroundings, parasitic signals contain usually high voltage (over 200 V) AC harmonics having variable impedance of 500 Ω to 10kΩ. The powerdissipation of thesesignals is divided between clamping diodes and the VCC. Simulationis used to determine the maximum energy level. The injected current value cannot in any case exceed 3A. 5. Output protective diodes are tested individually by means of positive and negative dischar ge voltages of a capacitor. The negative discharge control occurs through a single diode. During positive discharge, due to the properties of integration, a grounded collector PNP transistor appears in parallel with the clamping diode connected to VCC. A part of the current flows through this transistor, V CE being greater than VCC. If T is the total discharge duration, energy dissipated in the circuit is : T W =⌠ ⌡ [ i1 ⋅ vd + i2 (VCC + vd) ] dt O For a certain injected current, the lower the current I2, that is to say the lower the PNP current gain the smaller the energy is dissipated in the circuit. Topology and technological processes have been chosen to shorten this current gain. 3/10 ESM1600B 4/10 ESM1600B TYPICAL APPLICATIONS Figure 5 : Conversion of DTL, TTL, MOS Signals on a Transmitting Line. Figure 6 : Reception of Highly Noisy Signals. 5/10 ESM1600B TEST CIRCUIT Figure 7. Figure 8. Figure 10. 6/10 Figure 9. ESM1600B Figure 11. Figure 12. Figure 13 : Response Time. 7/10 ESM1600B DIP14 PACKAGE MECHANICAL DATA Millimeters Min. a1 0.51 B 1.39 Typ. Max. Min. Typ. Max. 0.020 1.65 0.055 0.065 b 0.5 0.020 b1 0.25 0.010 D 20 0.787 E 8.5 0.335 e 2.54 0.100 e3 15.24 0.600 F 7.1 0.280 i 5.1 0.201 L Z 8/10 Inches DIP14.TBL Dimensions 3.3 1.27 0.130 2.54 0.050 0.100 ESM1600B S016 PACKAGE MECHANICAL DATA Dimensions Millimeters Min. Typ. A Max. Min. Typ. 1.75 0.1 0.069 0.2 a2 Max. 0.004 0.008 1.6 0.063 b 0.35 0.46 0.014 0.018 b1 0.19 0.25 0.007 0.010 C 0.5 0.020 45o (typ.) c1 D 9.8 10 0.386 0.394 E 5.8 6.2 0.228 0.244 e 1.27 0.050 e3 8.89 0.350 F 3.8 4.0 0.150 0.157 G 4.6 5.3 0.181 0.209 L 0.5 1.27 0.020 0.050 M S 0.62 SO16.TBL a1 Inches 0.024 o 8 (max.) 9/10 ESM1600B Information furnished is believed to be accurate and reliable. However, SGS-THOMSON Microelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of SGS-THOMSON Microelectronics. Specification mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. SGS-THOMSON Microelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of SGS-THOMSON Microelectronics. 1997 SGS-THOMSON Microelectronics – Printed in Italy – All Rights Reserved SGS-THOMSON Microelectronics GROUP OF COMPANIES Australia - Brazil - Canada - China - France - Germany - Hong Kong - Italy - Japan - Korea - Malaysia - Malta - Morocco The Netherlands - Singapore - Spain - Sweden - Switzerland - Taiwan - Thailand - United Kingdom - U.S.A. 10/10