User Guide for FEBFL7701_L30U003A 2.4W LED Ballast Using FL7701 Featured Fairchild Product: FL7701 Direct questions or comments about this evaluation board to: “Worldwide Direct Support” Fairchild Semiconductor.com © 2012 Fairchild Semiconductor Corporation 1 FEBFL7701_L30U003A • Rev.1.0.2 Table of Contents 1. Introduction ............................................................................................................................... 3 1.1. General Description.......................................................................................................... 3 1.2. Key Features ..................................................................................................................... 3 1.3. Internal Block Diagram .................................................................................................... 4 2. General Specifications for Evaluation Board ........................................................................... 5 3. Photographs of the Evaluation Board ....................................................................................... 6 4. Printed Circuit Board ................................................................................................................ 7 5. Schematic .................................................................................................................................. 8 6. Bill of Materials ........................................................................................................................ 9 7. Test Condition & Test Equipment ............................................................................................ 9 8. Test Waveforms ...................................................................................................................... 10 8.1. 8.2. 8.3. 8.4. 8.5. Typical Waveforms: Startup .......................................................................................... 10 Operating frequency & minimum duty .......................................................................... 11 Typical waveforms: Steady State ................................................................................... 12 Typical waveforms: Abnormal Mode(LED Open) ........................................................ 15 Typical waveforms: Abnormal Mode (Inductor Short Condition) ................................ 16 9. Performance of Evaluation Board ........................................................................................... 17 9.1. 9.2. 9.3. 9.4. 9.5. Power Factor at Rated Load Condition .......................................................................... 17 System Efficiency .......................................................................................................... 18 THD Performance .......................................................................................................... 19 Thermal Performance ..................................................................................................... 20 EMI Results .................................................................................................................... 22 10. Revision History ..................................................................................................................... 24 © 2012 Fairchild Semiconductor Corporation 2 FEBFL7701_L30U003A • Rev. 1.0.2 This user guide supports the Evaluation kit for the FL7701. It should be used in conjunction with the FL7701 datasheet as well as Fairchild’s application notes and technical support team. Please visit Fairchild’s website at www.fairchildsemi.com. 1. Introduction This document describes the proposed solution for a universal-input 2.4W LED ballast using the FL7701. The input voltage range is 90VRMS – 265VRMS and there is one DC output with a constant current of 85mA at 28VMAX. This document contains general description of FL7701, the power supply specification, schematic, bill of materials, and the typical operating characteristics. 1.1. General Description The FL7701 LED lamp driver is a simple IC with PFC function. The special “adopted digital” technique automatically detects input voltage condition and sends an internal reference signal, resulting in high power factor. When an AC input voltage is applied to the IC, the PFC function is automatically enabled. Otherwise, when a DC input is applied to the IC, the PFC function is automatically disabled. The FL7701 does not require a bulk capacitor (electrolytic capacitor) for supply rail stability, which can significantly affect LED reliability. 1.2. Key Features Digitally Implemented Active PFC Function Built-in Self-Biasing HV Startup Circuit Application Input Range: 80VAC ~ 308VAC AOCP Function with Auto-Restart Mode Built-in Over-Temperature Protection Cycle-by-Cycle Current Limit Current-Sense Pin Open Protection Low Operating Current: 0.85mA (Typical) Under-Voltage Lockout with 5V Hysteresis Programmable Oscillator Frequency Programmable LED Current Analog Dimming Function Fixed Soft-Start Function Precise Internal Reference: ±3% © 2012 Fairchild Semiconductor Corporation 3 FEBFL7701_L30U003A • Rev. 1.0.2 1.3. Internal Block Diagram Figure 1. Internal Block Diagram Pin Descriptions Pin Symbol 1 CS 2 OUT Output. Connects to the MOSFET gate. 3 VCC Supply Voltage. Supply pin for stable IC operation; ZCD signal detection used for accurate PFC function. 4 RT Resistor. Programmable operating frequency using an external resistor connected to this PIN and the IC has fixed frequency when this pin is left open or floating. 5 ADIM Analog Dimming. Connects to the internal current source and can change the output current using an external resistor. If ADIM is not used, connect a 0.1µF bypass capacitor between ADIM and GND. 6 GND GROUND. Ground for the IC. 7 NC No Connection 8 HV High Voltage. Connect to the high-voltage line and supply current to the IC © 2012 Fairchild Semiconductor Corporation Description Current Sense. Limits output current, depending on the sensing resistor voltage. The CS pin is also used to set the LED current regulation. 4 FEBFL7701_L30U003A • Rev. 1.0.2 2. General Specifications for Evaluation Board All data for this table was measured at an ambient temperature of 25°C Table 1. Summary of Features and Performance Description Input Voltage Range AC Input Frequency Output Voltage/Current Output Power Symbol Value VIN,min 90V VIN,nom 220V VIN,max 265V fIN,min 47Hz fIN,max 64Hz VOUT 28V IOUT 85mA Output Power 2.41W Note 2 >78% At full load Efficiency Temperature Comments TFL7701 < 71.5°C TMOSFET < 59.5°C TINDUCTOR < 57.5°C Note 1 At full load (all at open frame, room temperature / still air) PCB Size 20mm (width) x 32mm (length) x 13mm (height) Initial Application LED bulb Notes: 1. The output current has ILEDPK ripple. To reduce ripple current, use a large electrolytic capacitor in parallel with the LED. Ensure the capacitor voltage rating is high enough to withstand an open-LED condition or use a Zener diode for protection. 2. The output power is not equal to the apparent power due to the slight phase shift between the output voltage and current. © 2012 Fairchild Semiconductor Corporation 5 FEBFL7701_L30U003A • Rev. 1.0.2 3. Photographs of the Evaluation Board Figure 2. Photograph Top View (20mm x 32mm x 13mm) Figure 3. Photograph Bottom View (20mm x 32mm x 13mm) Figure 4. Photograph Side View (20mm x 32mm x 13mm) © 2012 Fairchild Semiconductor Corporation 6 FEBFL7701_L30U003A • Rev. 1.0.2 4. Printed Circuit Board Figure 5. PCB, Top Side Figure 6. PCB, Bottom Side © 2012 Fairchild Semiconductor Corporation 7 FEBFL7701_L30U003A • Rev. 1.0.2 5. Schematic Figure 7. Schematic of Evaluation © 2012 Fairchild Semiconductor Corporation 8 FEBFL7701_L30U003A • Rev. 1.0.2 6. Bill of Materials Qty Reference Part Number Value Description Manufacturer Controller Fairchild Semiconductor PCB Silkscreen 1 U1 FL7701 1 BD MB6S 0.5A / 600V Diode, Bridge, 600V, 0.5A Fairchild Semiconductor 1 C1 MPE 630V223K 22nF Capacitor, 630VAC, 10%, Polypropylene Sungho C1 1 C2 MPE 630V333K 33nF Capacitor, 630VAC, 10%, Polypropylene Sungho C2 1 C3 C0805C101K3RACTU 100pF Capacitor, SMD, Ceramic, 25V, X7R Kemet ADIM 1 C4 C1206C225K3PACTU 2.2µF Capacitor, SMD, Ceramic, 25V, X7R Kemet VCC 1 D1 UF4007 1A / 1kV Diode, 1kV, 1A Ultra-Fast Recovery Fairchild Semiconductor FRD 1 D2 1N4148 1A / 100V 100V/1A, Small-Signal Diode Fairchild Semiconductor 4148 2 L1, L2 R06153KT00 15mH Inductor, Radial, R6.5x7.5 Bosung L1, L2 1 L3 R06402KT00 4mH Inductor, Radial, R6.5x7.5 Bosung L3 1 R1 RC1206JR-07680RL 680R Resistor,SMD,1/4W,1206 Yageo 1 R2 RC1206JR-0710KL 10k Resistor,SMD,1/4W,1206 Yageo 1 R3 RC0805JR-0724KL 24k Resistor,SMD,1/8W,0805 Yageo RT 1 R4 RC0805JR-07510RL 510R Resistor,SMD,1/8W,0805 Yageo RG 1 R5 RC1206JR-073RL 3.0R Resistor,SMD,1/4W,1206 Yageo RCS 7. Test Condition & Test Equipment Evaluation Board FEBFL7701_L30U003A Test Date 2012.01.19 Test Temperature TA = 25°C Test Equipments AC Source: PCR500L by Kikusui Power Meter: PZ4000 by Yokogawa Oscilloscope: Waverunner 64Xi by Lecroy EMI Test Receiver: ESCS30 by ROHDE & SCHWARZ Two-Line V-Network: ENV216 by ROHDE & SCHWARZ Thermometer: CAM SC640 by FLIR SYSTEMS LED: EHP-AX08EL/GT01H-P03 (3W) by Everlight © 2012 Fairchild Semiconductor Corporation 9 FEBFL7701_L30U003A • Rev. 1.0.2 8. Test Waveforms 8.1. Typical Waveforms: Startup Figure 8 through Figure 11 show the typical startup performance at different input voltage conditions. When AC input voltage is applied to the system, the FL7701 automatically operates in AC Mode after finishing an internally fixed, seven-cycle, softstart period. Figure 10 and Figure 11 show the soft-start characteristics when a DC input voltage is applied. CH1: VCC, CH2: VDRAIN, CH3: VLED, CH4: ILED CH1: VCC, CH2: VDRAIN, CH3: VLED, CH4: ILED Figure 8. Soft-Start Characteristics, AC Mode, 90VAC Figure 9. Soft-Start Characteristics, AC Mode, 265VAC CH1: VCC, CH2: VDRAIN, CH3: VLED, CH4: ILED CH1: VCC, CH2: VDRAIN, CH3: VLED, CH4: ILED Figure 10. Soft-Start Characteristics, DC Mode, 100VDC Figure 11. Soft-Start Characteristics, DC Mode, 200VDC © 2012 Fairchild Semiconductor Corporation 10 FEBFL7701_L30U003A • Rev. 1.0.2 8.2. Operating Frequency & Minimum Duty The programmable switching frequency is between 20kHz ~ 250kHz, determined by selecting the RT resistor value. If no RT resistor is used (RT pin OPEN), the FL7701 default switching frequency is set to 45kHz. The maximum duty ratio is fixed below 50% and has a fixed minimum typical on-time of 400ns. There are two crucial points to design properly. The first is consideration of the minimum duty ratio at minimum input voltage because the FL7701 is limited to 50% duty ratio. The second consideration is minimum on-time at maximum input voltage condition. The FL7701 cannot control output power when the operating conditions are such that the required on-time is less than the 400ns minimum on-time. Minimum on time: 1.12µs Switching frequency: 69.91kHz CH1: VCC, CH2: VDRAIN, CH3: VLED, CH4: ILED Figure 12. Operating Frequency & Minimum Duty © 2012 Fairchild Semiconductor Corporation 11 FEBFL7701_L30U003A • Rev. 1.0.2 8.3. Typical Waveforms: Steady State Figure 13 through Figure 22 show the normal operation waveform by input voltage & input frequency. The output voltage and current maintains a certain output level with 120Hz ripple, as shown in the test results in Table 2. CH1: VCC, CH2: VDRAIN, CH3: VLED, CH4: ILED CH1: VCC, CH2: VDRAIN, CH3: VLED, CH4: ILED Figure 13. Input Voltage: 90VAC, Input Frequency: 47Hz Figure 14. Input Voltage: 90VAC, Input Frequency: 64Hz H1: VCC, CH2: VDRAIN, CH3: VLED, CH4: ILED H1: VCC, CH2: VDRAIN, CH3: VLED, CH4: ILED Figure 15. Input Voltage: 110VAC, Input Frequency: 47Hz Figure 16. Input Voltage: 110VAC, Input Frequency: 64Hz © 2012 Fairchild Semiconductor Corporation 12 FEBFL7701_L30U003A • Rev. 1.0.2 Typical Operating Waveforms: Output Characteristics CH1: VCC, CH2: VDRAIN, CH3: VLED, CH4: ILED CH1: VCC, CH2: VDRAIN, CH3: VLED, CH4: ILED Figure 17. Input Voltage: 180VAC, Input Frequency: 47Hz Figure 18. Input Voltage: 180VAC, Input Frequency: 64Hz CH1: VCC, CH2: VDRAIN, CH3: VLED, CH4: ILED CH1: VCC, CH2: VDRAIN, CH3: VLED, CH4: ILED Figure 19. Input Voltage: 220VAC, Input Frequency: 47Hz Figure 20. Input Voltage: 220VAC, Input Frequency: 64Hz H1: VCC, CH2: VDRAIN, CH3: VLED, CH4: ILED Figure 21. Input Voltage: 265VAC, Input Frequency: 47Hz H1: VCC, CH2: VDRAIN, CH3: VLED, CH4: ILED Figure 22. Input Voltage: 265VAC, Input Frequency: 64Hz © 2012 Fairchild Semiconductor Corporation 13 FEBFL7701_L30U003A • Rev. 1.0.2 Table 2. Output Characteristics by Input Voltage & Frequency 47Hz 64Hz VLED(RMS) ILED(RMS) VLED(RMS) ILED(RMS) 90VAC 27.91V 84.45mA 27.90V 84.58mA 110VAC 27.99V 84.41mA 28.02V 84.49mA 180VAC 28.13V 84.94mA 28.10V 84.86mA 220VAC 28.12V 85.66mA 28.14V 85.77mA 265VAC 28.17V 87.05mA 28.13V 87.05mA © 2012 Fairchild Semiconductor Corporation 14 FEBFL7701_L30U003A • Rev. 1.0.2 8.4. Typical Waveforms: Abnormal Mode (LED Open) Figure 23 and Figure 24 show the open-load condition test method and result. When the LED disconnects from the system, the IC cannot operate because the HV pin is disconnected. Figure 23. Open-Load Condition Test CH1: VCC, CH2: VDRAIN, CH3: VLED, CH4: ILED Figure 24. © 2012 Fairchild Semiconductor Corporation Test Results of Open-Load Condition 15 FEBFL7701_L30U003A • Rev. 1.0.2 8.5. Typical Waveforms: Abnormal Mode (Inductor Short Condition) Figure 25 and Figure 26 show the test method and result of an inductor short condition. The FL7701 uses an abnormal over-current protection (AOCP) function, limiting the current on RCS in the event of an inductor short condition. Figure 25. Inductor Short Condition When CS pin voltage reached 2.5V, AOCP operates after internal delay time 70ns (typical) CH1: VCS, CH2: VDRAIN, CH3: VLED, CH4: ILED Figure 26. © 2012 Fairchild Semiconductor Corporation Test Results of Inductor Short Condition 16 FEBFL7701_L30U003A • Rev. 1.0.2 9. Performance of Evaluation Board 9.1. Power Factor at Rated Load Condition Figure 27 shows the system PF performance for the entire input voltage range (90V to 265V) at different input frequency conditions (47Hz, 64Hz). The PF slightly changes according to the input frequency but can achieve over 86% at 265VAC condition. 100 95 90 85 80 [%] 75 PF_47Hz 70 PF_64Hz 65 60 55 50 90 110 180 220 264 [VAC] Figure 27. Power Factor Table 3. PF Test Results Input Voltage 90VAC 110VAC 180VAC 220VAC 265VAC © 2012 Fairchild Semiconductor Corporation Power Factor 47Hz 96.31 64Hz 97.34 47Hz 96.72 64Hz 96.89 47Hz 94.41 64Hz 93.74 47Hz 92.49 64Hz 91.09 47Hz 89.71 64Hz 86.56 17 FEBFL7701_L30U003A • Rev. 1.0.2 9.2. System Efficiency Figure 28 shows system efficiency results for different AC input voltage frequency conditions. As shown, the input frequency has negligible effect on system efficiency. 100 95 90 85 80 [%] Efficiency_47Hz 75 Efficiency_64Hz 70 65 60 55 50 90 110 180 220 264 [VAC] Figure 28. System Efficiency Table 4. Efficiency Test Results Input Voltage 90VAC 110VAC 180VAC 220VAC 265VAC © 2012 Fairchild Semiconductor Corporation 18 Frequency Efficiency (%) 47Hz 83.56 64Hz 83.83 47Hz 83.36 64Hz 83.46 47Hz 80.04 64Hz 80.06 47Hz 77.68 64Hz 77.69 47Hz 75.11 64Hz 75.22 FEBFL7701_L30U003A • Rev. 1.0.2 9.3. THD Performance Figure 29 shows the THD performance at different input frequencies. Test results are quite similar, except the 90VAC condition, but meets international regulations (under 30%). 30 25 [%] 20 THD_47Hz 15 THD_64Hz 10 5 0 90 110 180 220 264 [VAC] Figure 29. THD Performance Table 5. THD Test Results Input Voltage 90VAC 110VAC 180VAC 220VAC 265VAC © 2012 Fairchild Semiconductor Corporation 19 Frequency THD (%) 47Hz 20.99 64Hz 21.82 47Hz 22.26 64Hz 22.46 47Hz 24.96 64Hz 25.31 47Hz 25.50 64Hz 25.84 47Hz 25.75 64Hz 26.72 FEBFL7701_L30U003A • Rev. 1.0.2 9.4. Thermal Performance Figure 30 through Figure 37 show the steady-state thermal results with different input voltage conditions. Inductor L3 has the highest temperature on the top side of the PCB due to copper resistance. The FL7701 has the highest temperature on the bottom side of the PCB due to power loss associated with the high-voltage device. The IC temperature is 66.5°C for the 220VAC input condition. Figure 30. Thermal Test Result, Bottom-Side Temperature at 90VAC Condition (IC) Figure 31. Thermal Test Result, Top-Side Temperature at 90VAC Condition (Inductor) Figure 32. Thermal Test Result, Bottom-Side Temperature at 110VAC Condition (IC) Figure 33. Thermal Test Result, Top-Side Temperature at 110VAC Condition (Inductor) © 2012 Fairchild Semiconductor Corporation 20 FEBFL7701_L30U003A • Rev. 1.0.2 Figure 34. Thermal Test Result, Bottom-Side Temperature at 220VAC Condition (IC) Figure 35. Thermal Test Result, Top-Side Temperature at 220VAC Condition (Inductor) Figure 36. Thermal Test Result, Bottom-Side Temperature at 264VAC Condition (IC) Figure 37. Thermal Test Result, Top-Side Temperature at 264VAC Condition (Inductor) Table 6. Temperature performance by Input voltage Input Voltage TIC TMOSFET TINDUCTOR 90VAC 47.6°C 46.2°C 47.8°C 110VAC 51.4°C 46.9°C 47.8°C 220VAC 66.5°C 55.0°C 54.6°C 265VAC 71.5°C 59.5°C 57.7°C © 2012 Fairchild Semiconductor Corporation 21 FEBFL7701_L30U003A • Rev. 1.0.2 9.5. EMI Results EMI test measurements were conducted in observance of CISPR22 criteria, which has tighter stricter limits than CISPR15 for lighting applications. Figure 38. Figure 39. © 2012 Fairchild Semiconductor Corporation EMI Test Results, Conducted Emission-Line at 110VAC Input Condition, Full Load (10-LED Series) EMI Test Results, Conducted Emission-Neutral at 110VAC Input Condition, Full Load (10-LED Series) 22 FEBFL7701_L30U003A • Rev. 1.0.2 Figure 40. EMI Test Results, Conducted Emission-Neutral at 220VAC Input Condition, Full Load (10-LED Series) Figure 41. EMI Test Results, Conducted Emission-Neutral at 220VAC Input Condition, Full Load (10-LED Series) © 2012 Fairchild Semiconductor Corporation 23 FEBFL7701_L30U003A • Rev. 1.0.2 10. Revision History Rev. Date 0.0.1 2011.11.16 1.0.1 2011.11.30 Update IC temperature 2012.2.20 Modified, edited, formatted document. Changed User Guide number from FEB_L030 to FEBFL7701_L30U003A 1.0.2 Description First issue WARNING AND DISCLAIMER Replace components on the Evaluation Board only with those parts shown on the parts list (or Bill of Materials) in the Users’ Guide. Contact an authorized Fairchild representative with any questions. This board is intended to be used by certified professionals, in a lab environment, following proper safety procedures. Use at your own risk. The Evaluation board (or kit) is for demonstration purposes only and neither the Board nor this User’s Guide constitute a sales contract or create any kind of warranty, whether express or implied, as to the applications or products involved. Fairchild warrantees that its products meet Fairchild’s published specifications, but does not guarantee that its products work in any specific application. Fairchild reserves the right to make changes without notice to any products described herein to improve reliability, function, or design. Either the applicable sales contract signed by Fairchild and Buyer or, if no contract exists, Fairchild’s standard Terms and Conditions on the back of Fairchild invoices, govern the terms of sale of the products described herein. DISCLAIMER FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION, OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS. LIFE SUPPORT POLICY FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, or (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. ANTI-COUNTERFEITING POLICY Fairchild Semiconductor Corporation's Anti-Counterfeiting Policy. Fairchild's Anti-Counterfeiting Policy is also stated on our external website, www.fairchildsemi.com, under Sales Support. Counterfeiting of semiconductor parts is a growing problem in the industry. All manufacturers of semiconductor products are experiencing counterfeiting of their parts. Customers who inadvertently purchase counterfeit parts experience many problems such as loss of brand reputation, substandard performance, failed applications, and increased cost of production and manufacturing delays. Fairchild is taking strong measures to protect ourselves and our customers from the proliferation of counterfeit parts. Fairchild strongly encourages customers to purchase Fairchild parts either directly from Fairchild or from Authorized Fairchild Distributors who are listed by country on our web page cited above. Products customers buy either from Fairchild directly or from Authorized Fairchild Distributors are genuine parts, have full traceability, meet Fairchild's quality standards for handling and storage and provide access to Fairchild's full range of up-to-date technical and product information. Fairchild and our Authorized Distributors will stand behind all warranties and will appropriately address any warranty issues that may arise. Fairchild will not provide any warranty coverage or other assistance for parts bought from Unauthorized Sources. Fairchild is committed to combat this global problem and encourage our customers to do their part in stopping this practice by buying direct or from authorized distributors. EXPORT COMPLIANCE STATEMENT These commodities, technology, or software were exported from the United States in accordance with the Export Administration Regulations for the ultimate destination listed on the commercial invoice. Diversion contrary to U.S. law is prohibited. U.S. origin products and products made with U.S. origin technology are subject to U.S Re-export laws. In the event of re-export, the user will be responsible to ensure the appropriate U.S. export regulations are followed. © 2012 Fairchild Semiconductor Corporation 24 FEBFL7701_L30U003A • Rev. 1.0.2