M54HC4538 M74HC4538 DUAL RETRIGGERABLE MONOSTABLE MULTIVIBRATOR . . . . . . . . HIGH SPEED tPD = 25 ns (TYP.) AT VCC = 5 V LOW POWER DISSIPATION STANDBY STATEICC =4 µA (MAX.) AT TA = 25 °C ACTIVE STATE ICC = 200 µA (TYP.) AT VCC = 5 V HIGH NOISE IMMUNITY VNIH = VNIL = 28 % VCC (MIN.) OUTPUT DRIVE CAPABILITY 10 LSTTL LOADS BALANCED PROPAGATION DELAYS tPLH = tPHL WIDE OUTPUT PULSE WIDTH RANGE tWOUT = 120 ns ~ 60 s OVER AT VCC = 4.5 V OUTPUT PULSE WIDTH INDEPENDENT FROM TRIGGER INPUT PULSE WIDTH PIN AND FUNCTION COMPATIBLE WITH 4538B B1R (Plastic Package) F1R (Ceramic Package) M1R (Micro Package) C1R (Chip Carrier) ORDER CODES : M54HC4538F1R M74HC4538M1R M74HC4538B1R M74HC4538C1R PIN CONNECTIONS (top view) DESCRIPTION The M54/74HC4538 is a high speed CMOS DUAL MONOSTABLEMULTIVIBRATOR fabricated in silicon gate C2MOS technology. It has the same high speed performance of LSTTL combined with true CMOS low power consumption. Each multivibrator features both a negative, A, and a positive, B, edge triggered input, either of which can be used as an inhibit input. Also included is a clear input that when taken low resets the one shot. The monostable multivibrators are retriggerable. That is, they may be triggered reapeatedly while their outputs are generating a pulse and the pulse will be extended. Pulse width stability over a wide range of temperature and supply is achieved using linear CMOS techniques. The output pulse equation is simply : PW = 0.7 (R)(C) where PW is in seconds, R in Ohms, and C is in Farads. All inputs are equipped with protection circuits against static discharge and transient excess voltage. October 1993 NC = No Internal Connection 1/14 M54/M74HC4538 SYSTEM DIAGRAM TIMING CHART 2/14 M54/ M74HC4538 BLOCK DIAGRAM Notes : 1. Cx, Rx, Dx are external components. 2. Dx is a clamping diode. 3. The external capacitor is charged to VCC in the stand-by state, i.e. no trigger. When the supply voltage is turned off Cx is discharged mainlythrough an internal parasitic diode (see figures). IfCx is sufficiently largeand VCC decreases rapidy, there willbesome possibility of damaging the I.C. with a surge current or latch-up. If the voltage supply filter capacitor is large enough and VCC decrease slowly, the surge current is automatically limited and damage the I.C. is avoided. The maximum forward current of the parasitic diode is approximately 20 mA. In cases where Cx is large the time taken for the supply voltage to fall to 0.4 VCC can be calculated as follows : tf ≥ (VCC – 0.7) ⋅ Cx/20 mA In cases where tf is too short an external champing diode is required to protect the I.C. from the surge current. FUNCTIONAL DESCRIPTION STAND-BY STATE The external capacitor, Cx, is fully charged to VCC in the stand-by state. Hence, before triggering, transistor Qp and Qn (connected to the Rx/Cx node) are both turned off. The two comparators that control the timing and the two reference voltage sources stop operating. The total supply current is therefore only leakage current. TRIGGER OPERATION Triggering occurs when : 1 st) A is ”low” and B has a falling edge ; 2 nd) B is ”high” and A has a rising edge ; After the multivibrator has been retriggered comparator C1 and C2 start operating and Qn is turned on. Cx then discharges through Qn. The voltage at the node Rx/Cx external falls. When it reaches VREFL the output of comparator C1 becomes low. This in turn resets the flip-flop and Qn is turned off. At this point C1 stops functioning but C2 continues to operate. The voltage at R/C external begins to rise with a time constant set by the external components Rx, Cx. Triggering the multivibrator causes Q to go high after internal delay due to the flip-flop and the gate. Q remains high until the voltage at R/C external rises again to VREFH. At this point C2 output goes low and G goes low. C2 stops operating. That means that after triggering when the voltage at R/C external returns to VREFH the multivibrator has returned to its MONOSTABLE STATE. In the case where Rx • Cx are large enough and the discharge time of the capacitor and the delay time in the I.C. can be ignored, the width of the output pulse tw (out) is as follows : tW(OUT) = 0.72 Cx • Rx RE-TRIGGER OPERATION When a second trigger pulse follows the first its effect will depend on the state of the multivibrator. If the capacitor Cx is being charged the voltage level of Rx/Cx external falls to VREFL again and Q remains high i.e. the retrigger pulse arrives in a time shorter than the period Rx • Cx seconds, the capacitor charging time constant. If the second trigger pulse is very close to the initial trigger pulse it is ineffective ; i.e., the second trigger must arrive in the capacitor discharge cycle to be ineffective. Hence the minimum time for a second trigger to be effective, trr (Min.) depends on VCC and Cx. 3/14 M54/M74HC4538 FUNCTIONAL DESCRIPTION (continued) RESET OPERATION CD is normally high. If CD is low, the trigger is not effective because Q output goes low and trigger control flip-flop is reset. Also transistor Op is turned on and Cx is charged quicky to VCC. This means if CD input goes low, the IC becomes waiting state both in operating and non operating state. TRUTH TABLE A INPUTS B CD H H L X H H X H L OUTPUTS Q Q OUTPUT ENABLE L L H H H X X L L H IEC LOGIC SYMBOL PIN No SYMBOL 1, 15 1T1, 2T1 External Capacitor Connections NAME AND FUNCTION 2, 14 1T2, 2T2 External Resistor/Capacitor Connections 3, 13 1CD, 2CD 4, 12 1A, 2A 5, 11 1B, 2B Direct Reset Inputs (Active LOW) Trigger Inputs (LOW to HIGH, Edge-Triggered) Trigger Inputs (HIGH to LOW, Edge-Triggered) 6, 10 Q1, Q2 Pulse Outputs 7, 9 8 Q1, Q2 GND Complementary Pulse Outputs Ground (0V) 16 VCC 4/14 Positive Supply Voltage INHIBIT INHIBIT OUTPUT ENABLE INPUT AND OUTPUT EQUIVALENT CIRCUIT PIN DESCRIPTION NOTE INHIBIT M54/ M74HC4538 ABSOLUTE MAXIMUM RATINGS Symbol Value Unit VCC VI Supply Voltage DC Input Voltage -0.5 to +7 -0.5 to VCC + 0.5 V V VO DC Output Voltage -0.5 to VCC + 0.5 V IIK IOK DC Input Diode Current DC Output Diode Current ± 20 ± 20 mA mA IO DC Output Source Sink Current Per Output Pin ± 25 mA DC VCC or Ground Current ± 50 mA 500 (*) mW ICC or IGND Parameter PD Power Dissipation Tstg TL Storage Temperature Lead Temperature (10 sec) -65 to +150 300 o o C C Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these condition isnotimplied. (*) 500 mW: ≅ 65 oC derate to 300 mW by 10mW/oC: 65 oC to 85 oC RECOMMENDED OPERATING CONDITIONS Symbol VCC Parameter Supply Voltage VI Input Voltage VO Top Output Voltage Operating Temperature: M54HC Series M74HC Series Input Rise and Fall Time (CLR only) tr, tf VCC = 2 V VCC = 4.5 V VCC = 6 V CX External Capacitor RX External Resistor Value 2 to 6 Unit V 0 to VCC V 0 to VCC -55 to +125 -40 to +85 0 to 1000 0 to 500 V C o C o ns 0 to 400 NO LIMITATION (*) VCC ≤ 3 V VCC > 3 V 5K to 1M (*) 1K to 1M (*) Ω (*) The maximum allowable values of Cx and Rx are a function of leakage of capacitor Cx, the leakage of device and leakage due to the board layout and surface resistance. Susceptibility to externally induced noise may occur for Rx > 1MΩ 5/14 M54/M74HC4538 DC SPECIFICATIONS Test Conditions Symbol VIH V IL Parameter High Level Input Voltage Low Level Input Voltage Value VCC (V) TA = 25 oC 54HC and 74HC Min. Typ. Max. 2.0 1.5 1.5 1.5 4.5 6.0 3.15 4.2 3.15 4.2 3.15 4.2 High Level Output Voltage 0.5 0.5 0.5 4.5 1.35 1.35 1.35 2.0 4.5 6.0 4.5 VOL Low Level Output Voltage 6.0 2.0 4.5 6.0 4.5 6.0 II II ICC ICC Input Leakage Current Input Leakage Current Quiescent Supply Current Quiescent Supply Current 6.0 6.0 6.0 2.0 4.5 6.0 6/14 1.8 1.8 Unit V 2.0 6.0 V OH -40 to 85 oC -55 to 125 oC 74HC 54HC Min. Max. Min. Max. V 1.8 1.9 2.0 1.9 1.9 VI = IO=-20 µA VIH or V IL IO=-4.0 mA 4.4 5.9 4.5 6.0 4.4 5.9 4.4 5.9 4.18 4.31 4.13 4.10 IO=-5.2 mA 5.68 5.8 0.0 5.63 5.60 V VI = IO= 20 µA VIH or V IL IO= 4.0 mA 0.1 0.1 0.1 0.0 0.1 0.1 0.1 0.0 0.17 0.1 0.26 0.1 0.37 0.1 0.40 IO= 5.2 mA 0.18 V 0.26 0.37 0.40 VI = VCC or GND ±0.1 ±1 ±1 µA VI = VCC or GND Rext/Cext VI = VCC or GND ±0.1 ±1 ±1 µA 4 40 80 µA VI = VCC or GND pins 2, 14 V I = V CC/2 40 120 160 µA 0.2 0.3 0.4 mA 0.3 0.6 0.8 mA M54/ M74HC4538 AC ELECTRICAL CHARACTERISTICS (C L = 50 pF, Input t r = tf = 6 ns) Test Conditions o TA = 25 C 54HC and 74HC Value -40 to 85 oC -55 to 125 oC 74HC 54HC Symbol Parameter VCC (V) tTLH tTHL Output Transition Time 2.0 4.5 Typ. 30 8 Max. 75 15 tPLH tPHL Propagation Delay Time (A, B - Q, Q) 6.0 2.0 4.5 6.0 7 120 30 25 13 250 50 43 16 315 63 54 19 375 75 64 tPLH tPHL Propagation Delay Time (CD - Q, Q) tWOUT Output Pulse Width 2.0 4.5 6.0 2.0 4.5 100 25 20 540 180 195 39 33 1200 250 245 49 42 1500 320 295 59 50 1800 375 150 83 77 77 200 96 85 85 70 69 69 260 96 85 85 70 69 69 320 96 85 85 µs 0.75 0.73 0.73 0.83 0.77 0.77 0.67 0.67 0.67 0.83 0.77 0.77 0.67 0.67 0.67 0.9 0.8 0.8 ms ∆tWOUT tW(H) tW(L) tW(L) tREM ts CIN CPD (*) Output Pulse Width Error Between Circuits (In same pack) Minimum Pulse Width (CLOCK) Minimum Pulse Width (CLEAR) Minimum Clear Removal Time Minimum Retrigger Time Input Capacitance Power Dissipation Capacitance Min. RX = 5KΩ CX = 0 RX = 1KΩ 6.0 2.0 4.5 6.0 RX = 1KΩ CX = 0.01 µF RX = 10KΩ 70 69 69 2.0 4.5 6.0 CX = 0.1 µF RX = 10KΩ 0.67 0.67 0.67 Min. Max. 95 19 Min. Max. 110 22 Unit ns ns ns ns ±1 % 2.0 30 75 95 110 4.5 6.0 8 7 15 13 19 16 22 19 2.0 4.5 30 8 75 15 95 19 110 22 ns 6.0 2.0 4.5 6.0 2.0 7 0 0 0 380 13 15 5 5 16 15 5 5 19 20 7 ns 4.5 6.0 2.0 4.5 6.0 CX = 0.1 µF RX = 1KΩ CX = 0.01 µF RX = 1KΩ 6 ns 92 72 6 1.4 1.2 5 70 ns µs 10 10 10 pF pF (*) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without load. (Refer to Test Circuit). Average operting current can be obtained by the following equation. ICC(opr) = CPD •VCC •fIN + ICC‘ •Duty/100 + ICC/2 (per circuit) (ICC‘ = Active Supply Current) (Duty = %)) 7/14 M54/M74HC4538 TEST CIRCUIT ICC (Opr.) Output Pulse Width Constant K = Supply Voltage. INPUT WAVEFORM IS THE SAME AS THAT IN CASE OF SWITCHING CHARACTERISTICS TEST. tWOUT - Cx Characteristics (Typ). 8/14 trr - VCC Characteristics (Typ). M54/ M74HC4538 SWITCHING CHARACTERISTICS TEST WAVEFORM 9/14 M54/M74HC4538 Plastic DIP16 (0.25) MECHANICAL DATA mm DIM. MIN. a1 0.51 B 0.77 TYP. inch MAX. MIN. TYP. MAX. 0.020 1.65 0.030 0.065 b 0.5 0.020 b1 0.25 0.010 D 20 0.787 E 8.5 0.335 e 2.54 0.100 e3 17.78 0.700 F 7.1 0.280 I 5.1 0.201 L Z 3.3 0.130 1.27 0.050 P001C 10/14 M54/ M74HC4538 Ceramic DIP16/1 MECHANICAL DATA mm DIM. MIN. TYP. inch MAX. MIN. TYP. MAX. A 20 0.787 B 7 0.276 D E 3.3 0.130 0.38 e3 0.015 17.78 0.700 F 2.29 2.79 0.090 0.110 G 0.4 0.55 0.016 0.022 H 1.17 1.52 0.046 0.060 L 0.22 0.31 0.009 0.012 M 0.51 1.27 0.020 0.050 N P Q 10.3 7.8 8.05 5.08 0.406 0.307 0.317 0.200 P053D 11/14 M54/M74HC4538 SO16 (Narrow) MECHANICAL DATA mm DIM. MIN. TYP. A a1 inch MAX. MIN. TYP. 1.75 0.1 0.068 0.2 a2 MAX. 0.004 0.007 1.65 0.064 b 0.35 0.46 0.013 0.018 b1 0.19 0.25 0.007 0.010 C 0.5 0.019 c1 45° (typ.) D 9.8 E 5.8 10 0.385 6.2 0.228 0.393 0.244 e 1.27 0.050 e3 8.89 0.350 F 3.8 4.0 0.149 0.157 G 4.6 5.3 0.181 0.208 L 0.5 1.27 0.019 0.050 M S 0.62 0.024 8° (max.) P013H 12/14 M54/ M74HC4538 PLCC20 MECHANICAL DATA mm DIM. MIN. TYP. inch MAX. MIN. TYP. MAX. A 9.78 10.03 0.385 0.395 B 8.89 9.04 0.350 0.356 D 4.2 4.57 0.165 0.180 d1 2.54 0.100 d2 0.56 0.022 E 7.37 8.38 0.290 0.330 e 1.27 0.050 e3 5.08 0.200 F 0.38 0.015 G 0.101 0.004 M 1.27 0.050 M1 1.14 0.045 P027A 13/14 M54/M74HC4538 Information furnished is believed to be accurate and reliable. However, SGS-THOMSON Microelectronics assumes no responsability for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may results from its use. No license is granted by implication or otherwise under any patent or patent rights of SGS-THOMSON Microelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. SGS-THOMSON Microelectronics products are not authorized for use ascritical components in life support devices or systems without express written approval of SGS-THOMSON Microelectonics. 1994 SGS-THOMSON Microelectronics - All Rights Reserved SGS-THOMSON Microelectronics GROUP OF COMPANIES Australia - Brazil - France - Germany - Hong Kong - Italy - Japan - Korea - Malaysia - Malta - Morocco - The Netherlands Singapore - Spain - Sweden - Switzerland - Taiwan - Thailand - United Kingdom - U.S.A 14/14