M74HC4852 DUAL 4:1 CHANNEL ANALOG MUX/DEMUX WITH INJECTION CURRENT PROTECTION ■ ■ ■ ■ ■ ■ ■ ■ ■ LOW POWER DISSIPATION: ICC = 2µA(MAX.) at TA=25°C INJECTION CURRENT PROTECTION: V∆OUT<1mV at VCC=5V IIN≤1mA R S≤3.9KΩ "ON" RESISTANCE at TA=25°C: 215Ω TYP. (VCC = 3.0V) 150Ω TYP. (VCC = 4.5V) 160Ω TYP. (VCC = 6V) FAST SWITCHING: tpd = 8.6ns (TYP.) at TA = 25 °C, VCC = 4.5V WIDE OPERATING SUPPLY VOLTAGE RANGE: VCC = 2V TO 6V HIGH NOISE IMMUNITY: VNIH = VNIL = 28 % VCC (MIN.) PIN AND FUNCTION COMPATIBLE WITH SERIES 4052, 4852 LATCH-UP PERFORMANCE EXCEEDS 500mA (JESD 17) ESD PERFORMANCE: HBM > 2000V (JESD22-A114B); MM > 200V DESCRIPTION The M74HC4852 is a dual four-channel analog MULTIPLEXER/DEMULTIPLEXER fabricated with silicon gate C2MOS technology. It is pin to pin compatible with the equivalent to standard HC4052 and MC14052, but features injection current effect control. This makes this device especially suited for usage in automotive applications where voltages in excess of normal SOP TSSOP ORDER CODES PACKAGE TUBE T&R SOP TSSOP M74HC4852M1R M74HC4852RM13TR M74HC4852TTR logic voltage are common. The injection current effect control allows signals at disabled input channels to exceed the supply voltage range or go down ground without affecting the signal of the enabled analog channel. This eliminates the need for external diode-resistor networks typically used to keep the analog channel signals within the supply voltage range. This analog switch is bidirectional and digitally controlled. It has two binary control inputs A and B to select 1 of 4 to be turned on, and connected to the output, and a INH input to disable all channels. All inputs and outputs are equipped with protection circuits against static discharge, giving them 2KV ESD immunity and transient excess voltage. PIN CONNECTION AND IEC LOGIC SYMBOLS September 2002 1/11 M74HC4852 CONTROL INPUT EQUIVALENT CIRCUIT PIN DESCRIPTION PIN No SYMBOL 3, 13 YCOM, XCOM 6 INH 7 NC 10, 9 A, B 12,14,15,11, X0 to X3, 1, 5, 2, 4 Y0 to Y3 8 GND 16 VCC NAME AND FUNCTION Common Output/Input INHIBIT Input Not Connected Select Inputs Independent Input/Outputs Ground (0V) Positive Supply Voltage TRUTH TABLE I/O EQUIVALENT CIRCUIT INPUT STATE ON CHANNEL INH B A L L L L H L L H H X L H L H X X: Don’t care FUNCTIONAL DIAGRAM 2/11 X0 X1 X2 X3 NONE Y0 Y1 Y2 Y3 NONE M74HC4852 ABSOLUTE MAXIMUM RATINGS Symbol Parameter Value Unit VCC Supply Voltage VIN Control Input Voltage VI/O Switch I/O Voltage ICK Control Input Diode Current IIOK I/O Diode Current ± 25 mA ICC DC VCC or Ground Current ± 50 mA PD Power Dissipation 500(*) 450(*) mW mW Tstg Storage Temperature -65 to +150 °C TL Lead Temperature (10 sec) 300 °C SOP TSSOP -0.5 to +7 V -0.5 to VCC + 0.5 -0.5 to VCC + 0.5 V V ± 25 mA Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is not implied (*) Power difssipation at 65 °C. Derating from 65°C to 125°C: SO Package -7mW/°C; TSSOP Package -6.1mW/°C RECOMMENDED OPERATING CONDITIONS Symbol Parameter Value Unit VCC Supply Voltage 2 to 6 V VI/O Input Output Voltage 0 to VCC V VI/O Static or Dynamic Voltage Across Switch (note1) 0 to 1.2 V VIN Control Input Voltage Top Operating Temperature tr, tf Input Rise and Fall Time (note2) VCC = 2.0V 0 to 1000 (Channel Select or Enable Inputs only) VCC = 3.0.V 0 to 800 VCC = 3.3V 0 to 700 VCC = 4.5V 0 to 500 VCC = 6.0V 0 to 400 0 to VCC V -55 to 125 °C ns 1) For voltage drops across switch greater than 1.2V (switch on), excessive Vcc current may drawn; i.e., the current out of the switch may containbothVCCandswitchinput components.Thereliabilityofthedevicewill beunaffectedunlesstheMaximumRatings areexceeded. 2) VIN from 30% to 70% VCC of channel Selected or Enable Inputs 3/11 M74HC4852 DC SPECIFICATIONS Test Condition Symbol VIHC VILC RON ∆RON IOFF IOFF ION IIN ICC 4/11 Parameter High Level Input Voltage Low Level Input Voltage ON Resistance Difference of ON Resistance between switches Input/Output Leakage Current (SWITCH OFF) (Any Channel) Input/Output Leakage Current (SWITCH OFF) (Common Channel) Switch Input Leakage Current (SWITCH ON, OUTPUT OPEN) Control Input Current Quiescent Supply Current TA = 25°C VCC (V) Min. 2.0 3.0 3.0 4.5 6.0 2.0 3.0 3.3 4.5 6.0 2.0 up to 85°C Typ. Max. Min. Max. 1.5 2.1 2.3 3.15 4.2 IS=2mA 3.0 3.3 4.5 6.0 IS≤2mA 2.0 IS=2mA 3.0 3.3 4.5 6.0 6.0 Value IS≤2mA VIN = VIHC or VILC VIS = VCC to GND VIN = VIHC or VILC VIS = VCC/2 VIN = VCC or GND 1.5 2.1 2.3 3.15 4.2 up to 125°C Min. Unit Max. 1.5 2.1 2.3 3.15 4.2 V 0.5 0.9 1.0 1.35 1.8 0.5 0.9 1.0 1.35 1.8 0.5 0.9 1.0 1.35 1.8 500 650 670 700 215 210 160 150 280 270 210 195 320 305 240 220 360 345 270 250 4 10 15 20 2 2 2 3 8 8 8 9 ±0.1 12 12 12 13 ± 0.5 16 16 16 18 ± 1.0 V Ω Ω µA ± 0.2 6.0 ±2 ±4 µA 6.0 VIN = VCC or GND ±0.1 ± 0.5 ±1 µA 6.0 VIN = VCC or GND ± 0.1 ± 0.1 ±1 6.0 VIN = VCC or GND VIN(analog)= GND 2 20 40 µA µA M74HC4852 AC ELECTRICAL CHARACTERISTICS (CL = 50 pF, Input tr = tf = 6ns) Test Condition Symbol Parameter tPHL,tPLH Propagation Delay Time, Analog Input to Analog Output tPHL,tPLH Propagation Delay Time Channel-Select to Analog Output tPHZtPZH Enable Disable tPLZ,tPZL Time, Enable or Channel-Select to Analog Output CIN CIN CIN CPD Input Capacitance (Digital Pins) Input Capacitance (Switches Off, Any Single Analog Pins) Input Capacitance (Switches Off, Any Common Analog Pins) Power Dissipation Capacitance (*) VCC (V) TEST CIRCUIT 1 Value TA = 25°C Min. 2.0 3.0 3.3 4.5 6.0 2.0 3.0 3.3 4.5 6.0 2.0 3.0 3.3 4.5 6.0 up to 85°C Typ. Max. Min. Max. 19.5 12 11 8.6 8 23 13.5 12.5 10 9.5 3.5 up to 125°C Min. Unit Max. 25 15.5 14.5 11.5 10 30 17.5 16.5 13 12.5 95 90 85 80 78 29 17.5 16.5 12.5 11 35 20 19 15 14.5 105 100 95 90 80 32 19.5 18.5 13.5 12 40 23 22 17 16.5 115 110 105 100 80 10 10 10 ns ns ns pF pF 6.7 15 15 15 pF 22 3.3 24 5.0 28 40 40 40 pF (*) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. ICC(opr) = CPD x VCC x fIN + ICC/8 INJECTION CURRENT COUPLING SPECIFICATION (TA= -55°C to +125°C) Test Condition Symbol V∆OUT Parameter Shift of Output Voltage of Enabled Analog Channel VCC (V) 3.3 5.0 3.3 5.0 3.3 5.0 3.3 5.0 Value Unit TEST CIRCUIT 2 Typ.(1) Max. IIN ≤ 1mA, RS ≤ 3.9KΩ 0.050 0.100 0.345 0.067 0.050 0.110 0.050 0.024 1.0 1.0 5.0 5.0 2.0 2.0 20 20 IIN ≤ 10mA, RS ≤ 3.9KΩ IIN ≤ 1mA, RS ≤ 20KΩ IIN ≤ 10mA, RS ≤ 20KΩ mV 1) Typical values are measured at TA=25°C e they are calculated as a difference from Vout without Injection Current and Vout with Injection Current. IIN = total current injected into any other disabled channel, one at time. 5/11 M74HC4852 TEST CIRCUIT 1 TEST tPLH, tPHL SWITCH Open tPZL, tPLZ VCC tPZH, tPHZ GND CL =50pF or equivalent (includes jig and probe capacitance) RL = R1 = 10KΩ or equivalent RT = ZOUT of pulse generator (typically 50Ω) TEST CIRCUIT 2 6/11 M74HC4852 WAVEFORM: PROPAGATION DELAY (f=1MHz; 50% duty cycle) WAVEFORM: PROPAGATION DELAY (f=1MHz; 50% duty cycle) 7/11 M74HC4852 WAVEFORM: PROPAGATION DELAY (f=1MHz; 50% duty cycle) CHANNEL RESISTANCE (RON) 8/11 ICC (Opr.) M74HC4852 SO-16 MECHANICAL DATA DIM. mm. MIN. TYP A a1 inch MAX. MIN. TYP. 1.75 0.1 0.068 0.2 a2 MAX. 0.003 0.007 1.65 0.064 b 0.35 0.46 0.013 0.018 b1 0.19 0.25 0.007 0.010 C 0.5 0.019 c1 45˚ (typ.) D 9.8 E 5.8 10 0.385 6.2 0.228 0.393 0.244 e 1.27 0.050 e3 8.89 0.350 F 3.8 4.0 0.149 0.157 G 4.6 5.3 0.181 0.208 L 0.5 1.27 0.019 0.050 M S 0.62 0.024 8 ˚ (max.) PO13H 9/11 M74HC4852 TSSOP16 MECHANICAL DATA mm. inch DIM. MIN. TYP A MAX. MIN. TYP. MAX. 1.2 A1 0.05 A2 0.8 b 0.047 0.15 0.002 0.004 0.006 1.05 0.031 0.039 0.041 0.19 0.30 0.007 0.012 c 0.09 0.20 0.004 0.0089 D 4.9 5 5.1 0.193 0.197 0.201 E 6.2 6.4 6.6 0.244 0.252 0.260 E1 4.3 4.4 4.48 0.169 0.173 0.176 1 e 0.65 BSC K 0˚ L 0.45 A 0.60 0.0256 BSC 8˚ 0˚ 0.75 0.018 8˚ 0.024 0.030 A2 A1 b e K c L E D E1 PIN 1 IDENTIFICATION 1 0080338D 10/11 M74HC4852 Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. © The ST logo is a registered trademark of STMicroelectronics © 2002 STMicroelectronics - Printed in Italy - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - Canada - China - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan - Malaysia - Malta - Morocco Singapore - Spain - Sweden - Switzerland - United Kingdom - United States. © http://www.st.com 11/11