VJ C0G (NP0) Dielectric Vishay Vitramon Surface Mount Multilayer Ceramic Chip Capacitors for Commercial Applications FEATURES • C0G is an ultra-stable dielectric offering a Temperature Coefficient of Capacitance (TCC) of 0 ppm/°C ± 30 ppm/°C • Low Dissipation Factor (DF) • Surface mount, wet build process • Reliable Noble Metal Electrode (NME) system • Halogen-free according to IEC 61249-2-21 APPLICATIONS • Timing and tuning circuits • Sensor and scanner applications • Snubber and surge suppression ELECTRICAL SPECIFICATIONS Insulation Resistance (IR): At + 25 °C and rated voltage 100 000 MΩ minimum or 1000 ΩF, whichever is less At + 125 °C and rated voltage 10 000 MΩ minimum or 100 ΩF, whichever is less Note: Electrical characteristics at + 25 °C unless otherwise specified Operating Temperature: - 55 °C to + 150 °C Capacitance Range: 1.0 pF to 0.056 µF Voltage Range: 10 Vdc to 1000 Vdc Dielectric Strength Test: Performed per Method 103 of EIA 198-2-E. Applied test voltages: ≤ 500 Vdc-rated: 200 % of rated voltage 630 Vdc/1000 Vdc-rated: 150 % of rated voltage Temperature Coefficient of Capacitance (TCC): 0 ppm/°C ± 30 ppm/°C from - 55 °C to + 125 °C Dissipation Factor (DF): 0.1 % maximum at 1.0 Vrms and 1 kHz for values > 1000 pF 0.1 % maximum at 1.0 Vrms and 1 MHz for values ≤ 1000 pF Aging Rate: 0 % maximum per decade ORDERING INFORMATION VJ0805 CASE CODE 0402 0603 0805 1206 1210 1808 1812 1825 2220 2225 A DIELECTRIC A = C0G (NP0) 102 CAPACITANCE NOMINAL CODE K CAPACITANCE TOLERANCE B = ± 0.10 pF Expressed in C = ± 0.25 pF picofarads (pF). D = ± 0.5 pF The first two F=±1% digits are G=±2% significant, the J=±5% third is a K = ± 10 % multiplier. An Note: “R” indicates a B, C, D < 10 pF decimal point. F, G, J, K ≥ 10 pF Examples: 102 = 1000 pF 1R8 = 1.8 pF X A DC VOLTAGE TERMINATION RATING (1) X = Ni barrier 100 % tin plate matte finish F = AgPd B = Polymer 100 % tin plate matte finish (5) X = 25 V A = 50 V B = 100 V C = 200 V E = 500 V L = 630 V G = 1000 V A MARKING ### (2)(4) PROCESS PACKAGING CODE T A = Unmarked M = Marked Note: Marking is only available for 0805 and 1206 with termination code ”X” T = 7" reel/plastic tape C = 7" reel/paper tape R = 11 1/4" reel/plastic tape P = 11 1/4" reel/paper tape O = 7" reel/flamed paper tape I = 11 1/4"/13" reel/flamed paper tape Note: “I” and “O” is used for “F” termination paper taped size 0402/0603/0805 Notes (1) DC voltage rating should not be exceeded in application (2) Process Code may be added with up to three digits, used to control non-standard products and/or special requirements (3) Case size designator may be replaced by a four digit drawing number used to control non-standard products and/or requirements (4) “A2” temporarily used to identify manufacturing plant for size ≥ 1812 (5) Selected values available, contact [email protected] for list of released ratings www.vishay.com 38 For technical questions, contact: [email protected] Document Number: 45053 Revision: 23-Sep-09 VJ C0G (NP0) Dielectric Surface Mount Multilayer Ceramic Chip Capacitors Vishay Vitramon for Commercial Applications DIMENSIONS in inches [millimeters] W L T MAX. P PART ORDERING NUMBER LENGTH (L) 0402 VJ0402 0.040 + 0.004/- 0.002 [1.00 + 0.10/- 0.05] 0.020 + 0.004/- 0.002 [0.50 + 0.10/- 0.05] 0603 VJ0603 0.063 ± 0.005 [1.60 ± 0.12] 0805 VJ0805 1206 EIA STYLE WIDTH (W) MAXIMUM THICKNESS (T) TERMINATION (P) MINIMUM MAXIMUM 0.024 [0.60] 0.004 [0.10] 0.016 [0.41] 0.031 ± 0.005 [0.80 ± 0.12] 0.037 [0.94] 0.012 [0.30] 0.018 [0.46] 0.079 ± 0.008 [2.00 ± 0.20] 0.049 ± 0.008 [1.25 ± 0.20] 0.057 [1.45] 0.010 [0.25] 0.028 [0.71] VJ1206 0.126 ± 0.008 [3.20 ± 0.20] 0.063 ± 0.008 [1.60 ± 0.20] 0.067 [1.70] 0.010 [0.25] 0.028 [0.71] 1210 VJ1210 0.126 ± 0.008 [3.20 ± 0.20] 0.098 ± 0.008 [2.50 ± 0.20] 0.067 [1.70] 0.010 [0.25] 0.028 [0.71] - VJ1808 0.177 ± 0.010 [4.50 ± 0.25] 0.080 ± 0.010 [2.03 ± 0.25] 0.067 [1.70] 0.010 [0.25] 0.030 [0.76] 1812 VJ1812 0.177 ± 0.010 [4.50 ± 0.25] 0.126 ± 0.008 [3.20 ± 0.20] 0.086 [2.18] 0.010 [0.25] 0.030 [0.76] 1825 VJ1825 0.177 ± 0.010 [4.50 ± 0.25] 0.252 ± 0.010 [6.40 ± 0.25] 0.086 [2.18] 0.010 [0.25] 0.030 [0.76] - VJ2220 0.220 ± 0.008 [5.59 ± 0.20] 0.200 ± 0.010 [5.08 ± 0.25] 0.086 [2.18] 0.010 [0.25] 0.030 [0.76] - VJ2225 0.220 ± 0.010 [5.59 ± 0.25] 0.250 ± 0.010 [6.35 ± 0.25] 0.086 [2.18] 0.010 [0.25] 0.030 [0.76] Note • Polymer terminations, “B” termination part number code, length dimensions, positive tolerances (including band width) above are allowed to increase by the following amounts: 0402/0603 size, consult [email protected] 0805/1210/1812/2220/2225 max. add length 0.0040"/0.10 mm 1206/1808 max. add length 0.0055"/0.14 mm Document Number: 45053 Revision: 23-Sep-09 For technical questions, contact: [email protected] www.vishay.com 39 VJ C0G (NP0) Dielectric Vishay Vitramon Surface Mount Multilayer Ceramic Chip Capacitors for Commercial Applications SELECTION CHART DIELECTRIC C0G (NP0) STYLE VJ0402 VJ0603 VJ0805 VJ1206 EIA TYPE 0402 0603 0805 1206 VOLTAGE (Vdc) 25 50 100 50 100 200 50 100 200 500 50 100 200 CAP. CAP. CODE 1R0 1.0 pF •• •• •• •• •• •• •• •• •• •• •• •• •• 1R2 1.2 pF •• •• •• •• •• •• •• •• •• •• •• •• •• 1R5 1.5 pF •• •• •• •• •• •• •• •• •• •• •• •• •• 1R8 1.8 pF •• •• •• •• •• •• •• •• •• •• •• •• •• 2R2 2.2 pF •• •• •• •• •• •• •• •• •• •• •• •• •• 2R7 2.7 pF •• •• •• •• •• •• •• •• •• •• •• •• •• 3R3 3.3 pF •• •• •• •• •• •• •• •• •• •• •• •• •• 3R9 3.9 pF •• •• •• •• •• •• •• •• •• •• •• •• •• 4R7 4.7 pF •• •• •• •• •• •• •• •• •• •• •• •• •• 5R6 5.6 pF •• •• •• •• •• •• •• •• •• •• •• •• •• 6R8 6.8 pF •• •• •• •• •• •• •• •• •• •• •• •• •• 8R2 8.2 pF •• •• •• •• •• •• •• •• •• •• •• •• •• 100 10 pF •• •• •• •• •• •• •• •• •• •• •• •• •• 120 12 pF •• •• •• •• •• •• •• •• •• •• •• •• •• 150 15 pF •• •• •• •• •• •• •• •• •• •• •• •• •• 180 18 pF •• •• •• •• •• •• •• •• •• •• •• •• •• 220 22 pF •• •• •• •• •• •• •• •• •• •• •• •• •• 270 27 pF •• •• •• •• •• •• •• •• •• •• •• •• •• 330 33 pF •• •• •• •• •• •• •• •• •• •• •• •• •• 390 39 pF •• •• •• •• •• •• •• •• •• •• •• •• •• 470 47 pF •• •• •• •• •• •• •• •• •• •• •• •• •• 560 56 pF •• •• •• •• •• •• •• •• •• •• •• •• •• 680 68 pF •• •• •• •• •• •• •• •• •• •• •• •• •• 820 82 pF •• •• •• •• •• •• •• •• •• •• •• •• •• 101 100 pF •• •• •• •• •• •• •• •• •• •• • • • 121 120 pF •• •• •• •• •• •• •• •• •• •• • • • 151 150 pF •• •• •• •• •• •• •• •• •• • • • 181 180 pF •• •• •• •• • •• •• •• •• • • • 221 220 pF •• •• •• •• • •• •• •• • • • • 271 270 pF •• •• • •• •• •• • • • • 331 330 pF •• •• •• •• •• • • • • 391 390 pF •• •• •• •• •• • • • • 471 470 pF •• •• •• • • • • • 561 560 pF •• •• •• • • • • 681 680 pF •• •• •• • • • • 821 820 pF •• •• •• • • • • 102 1000 pF •• •• • • • • 122 1200 pF •• • • • • 152 1500 pF •• • • • • 182 1800 pF • • • • 222 2200 pF • • • • 272 2700 pF • • • • 332 3300 pF • • • • 392 3900 pF • • • 472 4700 pF • • 562 5600 pF • 682 6800 pF • 822 8200 pF • 103 0.010 µF • 123 0.012 µF 153 0.015 µF 183 0.018 µF 223 0.022 µF 273 0.027 µF 333 0.033 µF 393 0.039 µF 473 0.047 µF 563 0.056 µF Note (1) See soldering recommendations within this data book, or visit www.vishay.com/doc?45034 •• Paper tape • Plastic tape www.vishay.com 40 For technical questions, contact: [email protected] 500 630 •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• • • • • • • • • • • • • • •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• • • • • • • • • • • • • • 50 • • • • • • • • • • • • • • • • • • • • • • VJ1210 (1) 1210 100 200 500 • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 630 • • • • • • • • • • • • • • • • • • • Document Number: 45053 Revision: 23-Sep-09 VJ C0G (NP0) Dielectric Surface Mount Multilayer Ceramic Chip Capacitors Vishay Vitramon for Commercial Applications SELECTION CHART DIELECTRIC STYLE EIA TYPE VJ1808 (1) - VJ1812 (1) 1812 C0G (NP0) VJ1825 (1) 1825 VJ2220 (1) - VOLTAGE (Vdc) 50 100 200 500 1000 50 100 200 500 1000 50 100 200 500 50 100 200 500 1000 CAP. CAP. CODE 1R0 1.0 pF 1R2 1.2 pF 1R5 1.5 pF 1R8 1.8 pF 2R2 2.2 pF 2R7 2.7 pF 3R3 3.3 pF 3R9 3.9 pF 4R7 4.7 pF 5R6 5.6 pF 6R8 6.8 pF 8R2 8.2 pF 100 10 pF 120 12 pF 150 15 pF 180 18 pF 220 22 pF 270 27 pF 330 33 pF 390 39 pF • • • • • 470 47 pF • • • • • 560 56 pF • • • • • 680 68 pF • • • • • • 820 82 pF • • • • • • 101 100 pF • • • • • • • • 121 120 pF • • • • • • • • • 151 150 pF • • • • • • • • • 181 180 pF • • • • • • • • • 221 220 pF • • • • • • • • • • • • 271 270 pF • • • • • • • • • • • • 331 330 pF • • • • • • • • • • • • 391 390 pF • • • • • • • • • • • • 471 470 pF • • • • • • • • • • • • 561 560 pF • • • • • • • • • • • • 681 680 pF • • • • • • • • • • • • 821 820 pF • • • • • • • • • • • • 102 1000 pF • • • • • • • • • • • • • • 122 1200 pF • • • • • • • • • • • • • 152 1500 pF • • • • • • • • • • • • • 182 1800 pF • • • • • • • • • • • • • 222 2200 pF • • • • • • • • • • • • • • 272 2700 pF • • • • • • • • • • • • • 332 3300 pF • • • • • • • • • • • • • 392 3900 pF • • • • • • • • • • • • • 472 4700 pF • • • • • • • • • • • • • 562 5600 pF • • • • • • • • • • • • 682 6800 pF • • • • • • • • • • • • • 822 8200 pF • • • • • • • • • • • • 103 0.010 µF • • • • • • • • • • • 123 0.012 µF • • • • • • • • • 153 0.015 µF • • • • • • • 183 0.018 µF • • • • • • 223 0.022 µF • • • • • • 273 0.027 µF • • • • 333 0.033 µF • • • 393 0.039 µF • 473 0.047 µF 563 0.056 µF Note: (1) See soldering recommendations within this data book, or visit www.vishay.com/doc?45034 • Plastic tape Document Number: 45053 Revision: 23-Sep-09 For technical questions, contact: [email protected] VJ2225 (1) 50 • • • • • • • • • • • • • • • • • • • • • 100 200 • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 500 • • • • • • • • • • • • • • • • • • • • • • • • • • www.vishay.com 41 VJ C0G (NP0) Dielectric Vishay Vitramon Surface Mount Multilayer Ceramic Chip Capacitors for Commercial Applications C0G (NP0) DIELECTRIC - TYPICAL PARAMETERS TEMPERATURE COEFFICIENT OF CAPACITANCE MIN. INSULATION RESISTANCE VS. TEMPERATURE 10 000 2.0 INSULATION RESISTANCE (ΩF) % CAPACITANCE CHANGE 1.5 1.0 1000 0.5 0.0 - 0.5 NP0 100 - 1.0 - 1.5 - 2.0 10 - 75 - 50 - 25 0 25 75 50 10 100 125 150 175 25 TEMPERATURE °C AGING RATE 0.2 % CAPACITANCE CHANGE % CAPACITANCE CHANGE 150 VOLTAGE COEFFICIENT OF CAPACITANCE 0.2 0.1 0.0 - 0.1 0.1 0.0 - 0.1 - 0.2 - 0.2 1 10 100 1000 10 000 0 10 20 50 60 70 80 90 100 DISSIPATION FACTOR 0.001 +1 0 -1 10 kHz 100 kHz 1 MHz 0.0005 0.00025 1 kHz FREQUENCY www.vishay.com 42 40 DISSIPATION FACTOR VS. FREQUENCY CHANGE OF CAPACITANCE WITH FREQUENCY +2 -2 1 kHz 30 DC VOLTS APPLIED HOURS % CAPACITANCE CHANGE 100 50 TEMPERATURE °C 10 kHz 100 kHz 1 MHz FREQUENCY For technical questions, contact: [email protected] Document Number: 45053 Revision: 23-Sep-09 Legal Disclaimer Notice Vishay Disclaimer All product specifications and data are subject to change without notice. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein or in any other disclosure relating to any product. Vishay disclaims any and all liability arising out of the use or application of any product described herein or of any information provided herein to the maximum extent permitted by law. The product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein, which apply to these products. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications unless otherwise expressly indicated. Customers using or selling Vishay products not expressly indicated for use in such applications do so entirely at their own risk and agree to fully indemnify Vishay for any damages arising or resulting from such use or sale. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. Product names and markings noted herein may be trademarks of their respective owners. Document Number: 91000 Revision: 18-Jul-08 www.vishay.com 1