STP11NK40Z - STP11NK40ZFP STB11NK40Z N-CHANNEL 400V - 0.49Ω - 9A TO-220/TO-220FP/D2PAK Zener-Protected SuperMESH™Power MOSFET TYPE STP11NK40Z STP11NK40ZFP STB11NK40Z ■ ■ ■ ■ ■ ■ VDSS RDS(on) ID Pw 400 V 400 V 400 V < 0.55 Ω < 0.55 Ω < 0.55 Ω 9A 9A 9A 110 W 30 W 110 W TYPICAL RDS(on) = 0.49 Ω EXTREMELY HIGH dv/dt CAPABILITY 100% AVALANCHE TESTED GATE CHARGE MINIMIZED VERY LOW INTRINSIC CAPACITANCES VERY GOOD MANUFACTURING REPEATIBILITY 3 1 TO-220 2 TO-220FP 3 1 D2PAK DESCRIPTION The SuperMESH™ series is obtained through an extreme optimization of ST’s well established stripbased PowerMESH™ layout. In addition to pushing on-resistance significantly down, special care is taken to ensure a very good dv/dt capability for the most demanding applications. Such series complements ST full range of high voltage MOSFETs including revolutionary MDmesh™ products. INTERNAL SCHEMATIC DIAGRAM APPLICATIONS HIGH CURRENT, HIGH SPEED SWITCHING ■ IDEAL FOR OFF-LINE POWER SUPPLIES, ADAPTORS AND PFC ■ LIGHTING ■ ORDERING INFORMATION SALES TYPE MARKING PACKAGE PACKAGING STP11NK40Z P11NK40Z TO-220 TUBE STP11NK40ZFP P11NK40ZFP TO-220FP TUBE STB11NK40ZT4 B11NK40Z D2PAK TAPE & REEL April 2003 1/12 STP11NK40Z - STP11NK40ZFP - STB11NK40Z ABSOLUTE MAXIMUM RATINGS Symbol Parameter Value Unit STP11NK40Z STB11NK40Z VDS VDGR VGS STP11NK40ZFP Drain-source Voltage (VGS = 0) 400 V Drain-gate Voltage (RGS = 20 kΩ) 400 V Gate- source Voltage ± 30 V ID Drain Current (continuous) at TC = 25°C 9 9(*) ID Drain Current (continuous) at TC = 100°C IDM () PTOT VESD(G-S) dv/dt (1) A 5.67 5.67(*) A Drain Current (pulsed) 36 36(*) A Total Dissipation at TC = 25°C 110 30 W Derating Factor 0.88 0.24 W/°C Gate source ESD(HBM-C=100pF, R=1.5KΩ) Peak Diode Recovery voltage slope Viso Insulation Withstand Voltage (DC) Tj Tstg Operating Junction Temperature Storage Temperature 3500 V 4.5 V/ns -- 2500 V -55 to 150 -55 to 150 °C °C ( ) Pulse width limited by safe operating area (1) ISD ≤9A, di/dt ≤200A/µs, VDD ≤ V(BR)DSS, Tj ≤ TJMAX. (*) Limited only by maximum temperature allowed THERMAL DATA TO-220 D2PAK TO-220FP Rthj-case Thermal Resistance Junction-case Max Rthj-amb Thermal Resistance Junction-ambient Max 62.5 °C/W Maximum Lead Temperature For Soldering Purpose 300 °C Tl 1.14 4.2 °C/W AVALANCHE CHARACTERISTICS Symbol Parameter IAR Avalanche Current, Repetitive or Not-Repetitive (pulse width limited by Tj max) EAS Single Pulse Avalanche Energy (starting Tj = 25 °C, ID = IAR, VDD = 50 V) Max Value Unit 9 A 190 mJ GATE-SOURCE ZENER DIODE Symbol BVGSO Parameter Gate-Source Breakdown Voltage Test Conditions Igs=± 1mA (Open Drain) Min. 30 Typ. Max. Unit V PROTECTION FEATURES OF GATE-TO-SOURCE ZENER DIODES The built-in back-to-back Zener diodes have specifically been designed to enhance not only the device’s ESD capability, but also to make them safely absorb possible voltage transients that may occasionally be applied from gate to source. In this respect the Zener voltage is appropriate to achieve an efficient and cost-effective intervention to protect the device’s integrity. These integrated Zener diodes thus avoid the usage of external components. 2/12 STP11NK40Z - STP11NK40ZFP - STB11NK40Z ELECTRICAL CHARACTERISTICS (TCASE =25°C UNLESS OTHERWISE SPECIFIED) ON/OFF Symbol Parameter Test Conditions Min. Typ. Max. Drain-source Breakdown Voltage ID = 1 mA, VGS = 0 IDSS Zero Gate Voltage Drain Current (VGS = 0) VDS = Max Rating VDS = Max Rating, TC = 125 °C 1 50 µA µA IGSS Gate-body Leakage Current (VDS = 0) VGS = ± 20 V ±10 µA VGS(th) Gate Threshold Voltage VDS = VGS, ID = 100 µA RDS(on) Static Drain-source On Resistance VGS = 10 V, ID = 4.5 A V(BR)DSS 400 Unit 3 V 3.75 4.5 V 0.49 0.55 Ω Typ. Max. Unit DYNAMIC Symbol gfs (1) Ciss Coss Crss Coss eq. (3) Parameter Test Conditions Min. Forward Transconductance VDS = 15 V, ID = 4.5 A 5.8 S Input Capacitance Output Capacitance Reverse Transfer Capacitance VDS = 25 V, f = 1 MHz, VGS = 0 930 140 30 pF pF pF Equivalent Output Capacitance VGS = 0 V, VDS = 0 V to 400 V 78 pF SWITCHING ON Symbol Parameter Test Conditions td(on) tr Turn-on Delay Time Rise Time VDD = 200 V, ID = 4.5 A RG = 4.7Ω VGS = 10 V (Resistive Load see, Figure 3) Qg Qgs Qgd Total Gate Charge Gate-Source Charge Gate-Drain Charge VDD = 320 V, ID =9 A, VGS = 10 V Min. Typ. Max. 20 20 Unit ns ns 32 6 18.5 45 nC nC nC Typ. Max. Unit SWITCHING OFF Symbol Parameter Test Conditions Min. td(off) tf Turn-off Delay Time Fall Time VDD =200 V, ID = 4.5 A RG = 4.7Ω VGS = 10 V (Resistive Load see, Figure 3) 40 18 ns ns tr(Voff) tf tc Off-voltage Rise Time Fall Time Cross-over Time VDD = 320 V, ID = 9 A, RG = 4.7Ω, VGS = 10 V (Inductive Load see, Figure 5) 15 17 30 ns ns ns SOURCE DRAIN DIODE Symbol Parameter Test Conditions ISD ISDM (2) Source-drain Current Source-drain Current (pulsed) VSD (1) Forward On Voltage ISD = 9 A, VGS = 0 Reverse Recovery Time Reverse Recovery Charge Reverse Recovery Current ISD = 9 A, di/dt = 100 A/µs VDD =45 V, Tj = 150°C (see test circuit, Figure 5) trr Qrr IRRM Min. Typ. 225 1.6 14 Max. Unit 9 36 A A 1.6 V ns µC A Note: 1. Pulsed: Pulse duration = 300 µs, duty cycle 1.5 %. 2. Pulse width limited by safe operating area. 3. Coss eq. is defined as a constant equivalent capacitance giving the same charging time as Coss when VDS increases from 0 to 80% VDSS. 3/12 STP11NK40Z - STP11NK40ZFP - STB11NK40Z Safe Operating Area For TO-220/D2PAK Thermal Impedance For TO-220/D2PAK Safe Operating Area For TO-220FP Thermal Impedance For TO-220FP Output Characteristics Transfer Characteristics 4/12 STP11NK40Z - STP11NK40ZFP - STB11NK40Z Transconductance Static Drain-source On Resistance Gate Charge vs Gate-source Voltage Capacitance Variations Normalized Gate Threshold Voltage vs Temp. Normalized On Resistance vs Temperature 5/12 STP11NK40Z - STP11NK40ZFP - STB11NK40Z Source-drain Diode Forward Characteristics Maximum Avalanche Energy vs Temperature 6/12 Normalized BVDSS vs Temperature STP11NK40Z - STP11NK40ZFP - STB11NK40Z Fig. 1: Unclamped Inductive Load Test Circuit Fig. 2: Unclamped Inductive Waveform Fig. 3: Switching Times Test Circuit For Resistive Load Fig. 4: Gate Charge test Circuit Fig. 5: Test Circuit For Inductive Load Switching And Diode Recovery Times 7/12 STP11NK40Z - STP11NK40ZFP - STB11NK40Z TO-220 MECHANICAL DATA mm DIM. MIN. inch TYP. MAX. MIN. TYP. MAX. A 4.40 4.60 0.173 0.181 C 1.23 1.32 0.048 0.051 D 2.40 2.72 0.094 D1 0.107 1.27 0.050 E 0.49 0.70 0.019 0.027 F 0.61 0.88 0.024 0.034 F1 1.14 1.70 0.044 0.067 F2 1.14 1.70 0.044 0.067 G 4.95 5.15 0.194 0.203 G1 2.4 2.7 0.094 0.106 H2 10.0 10.40 0.393 0.409 L2 16.4 0.645 13.0 14.0 0.511 0.551 L5 2.65 2.95 0.104 0.116 L6 15.25 15.75 0.600 0.620 L7 6.2 6.6 0.244 0.260 L9 3.5 3.93 0.137 0.154 DIA. 3.75 3.85 0.147 0.151 D1 C D A E L4 H2 G G1 F1 L2 F2 F Dia. L5 L9 L7 L6 8/12 L4 P011C STP11NK40Z - STP11NK40ZFP - STB11NK40Z TO-220FP MECHANICAL DATA mm. DIM. MIN. A 4.4 inch TYP MAX. MIN. TYP. MAX. 4.6 0.173 0.181 B 2.5 2.7 0.098 0.106 D 2.5 2.75 0.098 0.108 E 0.45 0.7 0.017 0.027 F 0.75 1 0.030 0.039 F1 1.15 1.5 0.045 0.067 F2 1.15 1.5 0.045 0.067 G 4.95 5.2 0.195 0.204 G1 2.4 2.7 0.094 0.106 H 10 10.4 0.393 0.409 L2 16 0.630 28.6 30.6 1.126 1.204 L4 9.8 10.6 .0385 0.417 L5 2.9 3.6 0.114 0.141 L6 15.9 16.4 0.626 0.645 L7 9 9.3 0.354 0.366 Ø 3 3.2 0.118 0.126 B D A E L3 L3 L6 F2 H G G1 ¯ F F1 L7 L2 L5 1 2 3 L4 9/12 STP11NK40Z - STP11NK40ZFP - STB11NK40Z D2PAK MECHANICAL DATA mm. inch DIM. MIN. TYP MAX. MIN. TYP. MAX. A 4.4 4.6 0.173 0.181 A1 2.49 2.69 0.098 0.106 A2 0.03 0.23 0.001 0.009 B 0.7 0.93 0.027 0.036 B2 1.14 1.7 0.044 0.067 C 0.45 0.6 0.017 0.023 C2 1.23 1.36 0.048 0.053 D 8.95 9.35 0.352 0.368 D1 E 8 0.315 10 E1 10.4 0.393 8.5 0.334 G 4.88 5.28 0.192 0.208 L 15 15.85 0.590 0.625 L2 1.27 1.4 0.050 0.055 L3 1.4 1.75 0.055 0.068 M 2.4 3.2 0.094 0.126 R 0.015 0º 8º 3 V2 0.4 10/12 1 STP11NK40Z - STP11NK40ZFP - STB11NK40Z D2PAK FOOTPRINT TUBE SHIPMENT (no suffix)* TAPE AND REEL SHIPMENT (suffix ”T4”)* REEL MECHANICAL DATA DIM. mm MIN. A DIM. mm inch MIN. MAX. MIN. A0 10.5 10.7 0.413 0.421 B0 15.7 15.9 0.618 0.626 D 1.5 1.6 0.059 0.063 D1 1.59 1.61 0.062 0.063 E 1.65 1.85 0.065 0.073 MAX. MIN. 330 B 1.5 C 12.8 D 20.2 G 24.4 N 100 T TAPE MECHANICAL DATA inch MAX. 12.992 0.059 13.2 0.504 0.520 26.4 0.960 1.039 0795 3.937 30.4 1.197 BASE QTY BULK QTY 1000 1000 MAX. F 11.4 11.6 0.449 0.456 K0 4.8 5.0 0.189 0.197 P0 3.9 4.1 0.153 0.161 P1 11.9 12.1 0.468 0.476 P2 1.9 2.1 R 50 1.574 T 0.25 0.35 0.0098 0.0137 W 23.7 24.3 0.075 0.082 0.933 0.956 * on sales 11/12 STP11NK40Z - STP11NK40ZFP - STB11NK40Z Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. © The ST logo is a registered trademark of STMicroelectronics © 2003 STMicroelectronics - Printed in Italy - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - Canada - China - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan - Malaysia - Malta - Morocco Singapore - Spain - Sweden - Switzerland - United Kingdom - United States. © http://www.st.com 12/12