STPC INDUSTRIAL PC Compatible Embedded Microprocessor ■ POWERFUL X86 PROCESSOR ■ 64-BIT BUS ARCHITECTURE ■ 64-BIT 66MHz DRAM CONTROLLER ■ SVGA GRAPHICS CONTROLLER ■ 135MHz RAMDAC ■ UMA ARCHITECTURE ■ TFT DISPLAY CONTROLLER ■ PCI MASTER / SLAVE / ARBITER ■ LOCAL BUS INTERFACE ■ ISA (MASTER/SLAVE) INTERFACE -INCLUDING THE IPC ■ PC-CARD INTERFACE - PCMCIA - CARDBUS ■ I/O FEATURES - PC/AT+ KEYBOARD CONTROLLER - PS/2 MOUSE CONTROLLER - 2 SERIAL PORTS - 1 PARALLEL PORT ■ ■ PBGA388 Figure 1. Logic Diagram x86 Core Serial1 Kbd Mouse Serial2 // Port Host I/F TFT ext ISA BUS IPC - DMA CONTROLLER - INTERRUPT CONTROLLER - TIMER / COUNTERS Local Bus I/F ISA I/F IPC 82C206 PCI POWER MANAGEMENT CONTROLLE R STPC INDUSTRIAL OVERVIEW The STPC Industrial integrates a fully static x86 processor, fully compatible with standard fifth generation x86 processors, and combines it with powerful chipset, graphics, TFT, PC-Card, Local Bus, keyboard, mouse, serials and parallel interfaces to provide a single Industrial oriented PC compatible subsystem on a single device. The performance of the device is comparable with the performance of a typical P5 generation system. The device is packaged in a 388 Plastic Ball Grid Array (PBGA). 5/11/99 PCI m/s PCI BUS PCMCIA CARDBUS GE HW Cursor Monitor VGA CRTC DRAM I/F TFT I/F TFT Output SYNC Output 1/55 Issue 1.1 STPC INDUSTRIAL ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ X86 Processor core Fully static 32-bit 5-stage pipeline, x86 processor fully PC compatible. Access up to 4GB of external memory. 8Kbyte unified instruction and data cache with write back capability. Parallel processing integral floating point unit, with automatic power down. Clock core speeds up to 100 MHz. Fully static design for dynamic clock control. Low power and system management modes. Optimized design for 3.3V operation. DRAM Controller Integrated system memory and graphic frame memory. Supports up to 128-MByte system memory in 4 banks and down to as little as 2Mbytes. Supports 4-MByte, 8-MByte, 16-MByte, and 32-MByte single-sided and double-sided DRAM SIMMs. Four quad-word write buffers for CPU to DRAM and PCI to DRAM cycles. Four quad-word read prefetch buffers for PCI masters. Supports Fast Page Mode & EDO DRAMs. Programmable timing for DRAM parameters including CAS pulse width, CAS pre-charge time, and RAS to CAS delay. 60, 70, 80 & 100ns DRAM speeds. Memory hole between 1 MByte & 8 MByte supported for PCI/ISA busses. Hidden refresh. ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Graphics Controller 64-bit windows accelerator. Complete backward compatibility to VGA and SVGA standards. Hardware acceleration for text (generalized bit map expansion), bitblts, transparent blts and fills. Up to 64 x 64 bit graphics hardware cursor. Up to 4MB long linear frame buffer. 8, 16, 24 and 32 bit pixels. Drivers for Windows and other operating systems. ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ 2/55 Issue 1.1 CRT Controller Integrated 135MHz triple RAMDAC allowing for 1280 x 1024 x 75Hz display. Requires external frequency synthesizer and reference sources. 8, 16, 24 and 32-bit pixels. Interlaced or non-interlaced output. TFT Interface Programmable panel size up to 1024 by 1024 pixels. Support for 640 x 480, 800 x 600 & 1024 x 768 active matrix TFT flat panels with 9, 12, 18-bit interface. Support 1 & 2 Pixels per Clock. Programmable image positionning. Programmable blank space insertion in text mode. Programmable horizontal and vertical image expansion in graphic mode. A fully programmable PWM (Pulse Width Modulator) signals to adjust the flat panel brightness and contrast. Supports PanelLinkTM high speed serial transmitter externally for high resolution panel interface. PCI Controller Fully compliant with PCI Version 2.1 specification. Integrated PCI arbitration interface. Up to 3 masters can connect directly. External PAL allows for greater than 3 masters. Translation of PCI cycles to ISA bus. Translation of ISA master initiated cycle to PCI. Support for burst read/write from PCI master. 0.33X and 0.5X CPU clock PCI clock. Local Bus interface 66MHz, low latency bus. Asynchronous / synchronous. 22-bit address and 16-bit data busses. 2 Programmable Flash EPROM Chip Select. 4 Programmable I/O Chip Select. Separate memory and I/O address spaces. Memory prefetch (improved performances). STPC INDUSTRIAL ■ ■ ■ ■ ■ ■ ■ ■ ■ ISA master/slave Generation of the ISA clock from either 14.318MHz oscillator clock or system clock Programmable extra wait state for ISA cycles Supports I/O recovery time for back to back I/O cycles. Fast Gate A20 and Fast reset. Supports the single ROM that C, D, or E. blocks shares with F block BIOS ROM. Supports flash ROM. Supports ISA hidden refresh. Buffered DMA & ISA master cycles to reduce bandwidth utilization of the PCI and Host bus. NSP compliant. ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ PC-Card interface Support one PCMCIA 2.0 / JEIDA 4.1 68-pin standard PC Card Socket. Power Management support. Support PCMCIA/ATA specifications. Support I/O PC Card with pulse-mode interrupts. Provides an ExCATM implementation to PCMCIA 2.0 / JEIDA 4.1 standards. DMA support. Keyboard interface Fully PC/AT& compatible ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Mouse interface Fully PS/2 compatible ■ ■ Serial interface 15540 compatible Programmable word length, stop bits, parity. 16-bit programmable baud rate generator. Interrupt generator. Loop-back mode. 8-bit scratch register. Two 16-bit FIFOs. Two DMA handshake lines. Parallel port Standard Centronics mode supported. Nibble mode supported. Integrated Peripheral Controller Two 8237/AT compatible 7-channel DMA controllers. Two 8259/AT compatible interrupt Controller. 16 interrupt inputs - ISA and PCI. Three 8254 compatible Timer/Counters. Co-processor error support logic. Power Management Four power saving modes: On, Doze, Standby, Suspend. Programmable system activity detector Supports SMM. Supports IO trap & restart. Independent peripheral time-out timer to monitor hard disk, serial & parallel ports. Supports APM Supports RTC, interrupt and DMA wake ups ExCA is a trademark of PCMCIA / JEIDA. PanelLink is a trademark of SiliconImage, Inc 3/55 Issue 1.1 GENERAL DESCRIPTION 1 GENERAL DESCRIPTION At the heart of the STPC Industrial is an advanced 64-bit processor block, dubbed the 5ST86. The 5ST86 includes a powerful x86 processor core along with a 64-bit DRAM controller, advanced 64-bit accelerated graphics and video controller, a high speed PCI local-bus controller and Industry standard PC chip set functions (Interrupt controller, DMA Controller, Interval timer and ISA bus). The STPC Industrial has in addition to the 5ST86 a TFT output, a Local Bus interface, PC Card and super I/O features. The STPC Industrial makes use of a tightly coupled Unified Memory Architecture (UMA), where the same memory array is used for CPU main memory and graphics frame-buffer. This means a reduction in total system memory for system performances that are equal to that of a comparable frame buffer and system memory based system, and generally much better, due to the higher memory bandwidth allowed by attaching the graphics engine directly to the 64-bit processor host interface running at the speed of the processor bus rather than the traditional PCI bus. The 64-bit wide memory array provides the system with 320MB/s peak bandwidth, double that of an equivalent system using 32 bits. This allows for higher resolution screens and greater color depth. The processor bus runs at 66Mhz further increasing “standard” bandwidth by at least a factor of two. The ‘standard’ PC chipset functions (DMA, interrupt controller, timers, power management logic) are integrated together with the x86 processor core; additional functions such as communication ports are accessed by the STPC Industrial via an internal ISA bus. The PCI bus is the main data communication link to the STPC Industrial chip. The STPC Industrial translates appropriate host bus I/O and Memory cycles onto the PCI bus. It also supports the generation of Configuration cycles on the PCI bus. The STPC Industrial, as a PCI bus agent (host bridge class), fully complies with PCI specification 2.1. The chip-set also implements the PCI mandatory header registers in Type 0 PCI configuration space for easy porting of PCI aware system BIOS. The device contains a PCI arbitration function for three external PCI devices. Graphics functions are controlled through the onchip SVGA controller and the monitor display is produced through the 2D graphics display engine. 4/55 Issue 1.1 This Graphics Engine is tuned to work with the host CPU to provide a balanced graphics system with a low silicon area cost. It performs limited graphics drawing operations which include hardware acceleration of text, bitblts, transparent blts and fills. The results of these operations change the contents of the on-screen or offscreen frame buffer areas of DRAM memory. The frame buffer can occupy a space up to 4 Mbytes anywhere in the physical main memory. The maximum graphics resolution supported is 1280x1024 in 65536 colours at 75Hz refresh rate and is VGA and SVGA compatible. Horizontal timing fields are VGA compatible while the vertical fields are extended by one bit to accommodate above display resolution. To generate the TFT output, the STPC Industrial extracts the digital video stream before the RAMDAC and reformats it to the TFT format. The height and width of the flat panel are programmable through configuration registers up to a size of 1024 by 1024. By default, lower resolution images cover only a part of the larger TFT panel. The STPC Industrial allows to expand the image vertically and horizontally in text mode by inserting programmable blank pixels. It allows expantion of the image vertically and horizontally in graphics mode by replicating pixels. The replication of J times every K pixel is independently programmable in the vertical and horizontal directions. PanelLinkTM is a proprietary interconnect protocol defined by Silicon Image, Inc. It consists of a transmitter that takes parallel video/graphics data from the host LCD graphics controller and transmits it serially at high speed to the receiver which controls the TFT panel. The TFT interface is designed to support the connection of this control signal to the PanelLinkTM transmitter. The STPC Industrial CARDBUS / PCMCIA controller has been specifically designed to provide the interface with PC-Cards which contain additional memory or I/O and provides an ExCATM implementation to PCMCIA 2.0 / JEIDA 4.1 standards. The power management control facilities include socket power control, insertion/removal capability, power saving with Windows inactivity, NCS controlled Chip Power Down, together with further controls for 3.3v suspend with Modem Ring Resume Detection. GENERAL DESCRIPTION The need for system configuration jumpers is eliminated by providing address mapping support for PCMCIA 2.0 / JEIDA 4.1 PC-Card memory together with address windowing support for I/O space. Selectable interrupt steering from PC-Card to internal system bus is also provided. The STPC Industrial implements a multi-function parallel port. The standard PC/AT compatible logical address assignments for LPT1, LPT2 and LPT3 are supported. The parallel port can be configured for any of the following 3 modes and supports the IEEE Standard 1284 parallel interface protocol standards as follow: -Compatibility Mode (Forward channel, standard) -Nibble Mode (Reverse channel, PC compatible) The STPC Industrial core is compliant with the Advanced Power Management (APM) specification to provide a standard method by which the BIOS can control the power used by personal computers. The Power Management Unit module (PMU) controls the power consumption providing a comprehensive set of features that control the power usage and supports compliance with the United States Environmental Protection Agency’s Energy Star Computer Program. The PMU provides following hardware structures to assist the software in managing the power consumption by the system. - System Activity Detection. - 3 power-down timers detecting system inactivity: - Doze timer (short durations). - Stand-by timer (medium durations). - Suspend timer (long durations). - House-keeping activity detection. -Byte Mode (Reverse channel, PS/2 compatible) The STPC Industrial BGA package has 388 balls, but this is not sufficient for all the integrated functions, therefore some features are sharing the same balls and can not be used at the same time. The STPC Industrial configuration is done by ‘strap options’. It is a set of pull-up or pull-down resistors on the memory data bus, checked on reset, which auto-configure the STPC Industrial. We can distinguish three main blocks independently configurables : The ISA / Local Bus block, the Serial 1 / TFT block, and the PCI / PC Card block. From the first block, we can activate either the ISA bus and some IPC additionnal features, or the Local bus, the parallel port and the second serial interface. From the second block, we can activate either the first serial port, or the TFT extension to get from 4 bit per colour to 6 bit per colour. From the third block, we can activate either the PCI bus, or the PC Card interface (CardBus/ PCMCIA/ZoomVideo). - House-keeping timer to cope with short bursts of house-keeping activity while dozing or in stand-by state. - Peripheral activity detection. - Peripheral timer detecting peripheral inactivity - SUSP# modulation to adjust the system performance in various power down states of the system including full power on state. - Power control outputs to disable power from different planes of the board. Lack of system activity for progressively longer periods of time is detected by the three power down timers. These timers can generate SMI interrupts to CPU so that the SMM software can put the system in decreasing states of power consumption. Alternatively, system activity in a power down state can generate SMI interrupt to allow the software to bring the system back up to full power on state. The chip-set supports up to three power down states described above, these correspond to decreasing levels of power savings. Power down puts the STPC Industrial into suspend mode. The processor completes execution of the current instruction, any pending decoded instructions and associated bus cycles. During the suspend mode, internal clocks are stopped. Removing power down, the processor resumes instruction fetching and begins execution in the instruction stream at the point it had stopped. Because of the static nature of the core, no internal data is lost.. 5/55 Issue 1.1 GENERAL DESCRIPTION Figure 1.1. Functionnal description. x86 Core Serial 1 Serial 2 // Port Host I/F ISA BUS Local Bus I/F TFT extension Kbd Mouse ISA m/s IPC 82C206 PCI m/s PCI m/s PCI BUS PCMCIA CARDBUS GE HW Cursor Monitor VGA TFT I/F CRTC TFT Output SYNC Output DRAM I/F 6/55 Issue 1.1 GENERAL DESCRIPTION Figure 1.2. PCI, PCMCIA & CARDBUS modes: PCI m/s PCI BUS PCMCIA CARDBUS PCI m/s PCI BUS PCMCIA CARDBUS PCI m/s PCI BUS PCMCIA CARDBUS 7/55 Issue 1.1 GENERAL DESCRIPTION Figure 1.3. Local Bus and ISA bus modes: Serial 2 // Port ISA BUS Local Bus I/F ISA m/s IPC 82C206 Serial 2 // Port ISA BUS Local Bus I/F ISA m/s IPC 82C206 Figure 1.4. TFT in normal (serial 1 available) and extended modes (serial 1 unavailable). Kbd Mouse Serial 1 TFT extension Kbd Mouse 9-bit mode 12-bit mode Serial 1 TFT extension 18-bit mode 2 x 9-bit mode TFT I/F TFT I/F TFT Output 8/55 Issue 1.1 TFT Output GENERAL DESCRIPTION Figure 2. Typical PC oriented Application IDE Serial Ports Parallel Port Floppy Super I/O RTC Flash ISA MUX IRQ Monitor SVGA MUX DMA.REQ TFT STPC Industrial Keyboard DMA.ACK DMUX Mouse PCI 4x 16-bit EDO DRAMs 9/55 Issue 1.1 GENERAL DESCRIPTION Figure 3. Typical Embedded Application STPC Local Bus SRAM I/O Peripheral Flash MUX IRQ Monitor SVGA TFT PC-Card STPC Industrial Keyboard Mouse PCMCIA CARDBUS Serial Ports Parallel Port 4x 16-bit EDO DRAMs 10/55 Issue 1.1 STRAP OPTION 2 STRAP OPTION This chapter defines the STPC Industrial Strap Options and their location Memory Data Refer to Lines MD0 MD1 MD2 DRAM Bank 1 MD3 MD4 MD5 DRAM Bank 0 MD6 MD7 MD8 MD9 MD10 DRAM Bank 3 MD11 MD12 MD13 DRAM Bank 2 MD14 MD15 MD16 MD17 PCI Clock MD18 Host Clock MD19 Graphics Clock MD20 DOT Clock MD21 MD22 MD23 MD24 HCLK MD25 MD26 Designation Location Reserved Reserved Speed Speed Type Speed Speed Type Reserved Reserved Speed Speed Type Speed Speed Type Reserved PCI_CLKO Divisor HCLK Pad Direction GCLK2x Pad Direction DCLK Pad Direction Reserved External IPC Debug Option Reserved HCLK PLL Speed MD27 MD28 MD29 MD30 Reserved Reserved Reserved Reserved MD31 MD32 MD33 MD34 MD35 MD 36 MD 37 MD 38 Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Index Index Index Index Index Index Index Index Index Index Index Index Index Index Index Index Index 4A,bit 2 4A,bit 3 4A,bit 4 4A,bit 5 4A,bit 6 4A,bit 7 4B,bit 2 4B,bit 3 4B,bit 4 4B,bit 5 4B,bit 6 4B,bit 7 4C,bit 0 4C,bit 1 4C,bit 2 4C,bit 3 4C,bit 4 Index 5F,bit 1 Index 5F,bit 2 Index 5F,bit 3 Index 5F,bit 4 Index 5F,bit 5 Actual Settings User defined Pull up User defined User defined Pull up User defined User defined Pull up User defined User defined Pull up User defined Set to ’0’ Set to ’1’ 70 ns 60 ns EDO 70 ns FPM 60 ns EDO 70 ns FPM 60 ns EDO 70 ns FPM 60 ns EDO FPM User defined HCLK / 3 HCLK / 2 User defined External Internal User defined External Internal User defined External Internal Pull up Pull up External IPC Internal IPC Pull up User defined 000 25 MHz User defined 001 33 MHz User defined 010 40 MHz 011 50 MHz 100 60 MHz 101 66 MHz 110 75 MHz 111 80 MHz Pull down Pull down Pull down Pull down Pull down Pull down Pull up Pull down Pull up Pull up Pull up Pull up 11/55 Issue 1.1 STRAP OPTION Memory Data Refer to Lines MD 39 MD 40 MD 41 MD 42 MD 43 MD 44 Serial Port MD 45 MD 46 MD 47 MD 48 TFT Designation Location Actual Settings Reserved PCMCIA or PCI i/f Local Bus or ISA i/f Key Board & Mouse Parallel Port UART1 UART2 Reserved Reserved Outputs on RFU pads 3C,bit 0 3C,bit 1 3C,bit 2 3C,bit 3 3C,bit 4 3C,bit 5 3C,bit 6 3C,bit 7 3D,bit 0 Pull up User defined User defined User defined User defined User defined User defined Pull down Pull down User defined 5V Availability 3D,bit 1 User defined MD 50 3.3V Availability 3D,bit 2 User defined MD 51 x.xV Available 3D,bit 3 User defined MD 52 y.yV Available 3D,bit 4 User defined MD 53 MD 56 MD 57 MD 58 MD 59 Reserved Reserved Reserved Reserved Reserved MD 49 Cardbus Socket Set to ’0’ Set to ’1’ PCI ISA External External External External PCMCIA Local Bus Internal Internal Internal Internal Disable Not Available Not Available Not Available Not Available Enable Available Available Available Available Pull uo Pull up Pull down Pull up Pull down 2.1 STRAP OPTION REGISTER DESCRIPTION 2.1.1 STRAP REGISTER 0 INDEX 4AH (STRAP0) Bits 7-0, This register reflect the status of pins MD[7:0] respectively. They are expected to be connected on the system board to the SIMM configuration pins as follows: Bit Sampled Bit 7 Bits 6-5 Bit 4 Bits 3-2 Bits 1-0 Description SIMM 0 DRAM type SIMM 0 speed SIMM 1 DRAM type SIMM 1 speed Reserved Note that the SIMM speed and type information read here is meant only for the software and is not used by the hardware. The software must program the Host and graphics DRAM controller configuration registers appropriately based on these bits. This register defaults to the values sampled on MD[7:0] pins after reset. 12/55 Issue 1.1 STRAP OPTION 2.1.2 STRAP REGISTER 1 INDEX 4BH (STRAP1) Bits 7-0, This register reflect the status of pins MD[15:8] respectively. They are expected to be connected on the system board to the SIMM configuration pins as follows: Bit Sampled Bit 7 Bits 6-5 Bit 4 Bits 3-2 Bit 1-0 Description SIMM 2 DRAM type SIMM 2 speed SIMM 3 DRAM type: SIMM 3 speed Reserved Note that the SIMM speed and type information read here is meant only for the software and is not used by the hardware. The software must program the Host and graphics dram controller configuration registers appropriately based on these bits. This register defaults to the values sampled on MD[15:8] pins after reset. 2.1.3 STRAP REGISTER 2 INDEX 4CH (STRAP2) Bits 4-0 of this register reflect the status of pins MD[20:16] respectively. Bit 5 of this register reflect the status of pin MD[23]. Bit 4 is writeable, writes to other bits in this register have no effect. They are use by the chip as follows: Bits 7-5, Reserved Bit 4, This bit reflects the value sampled on MD[20] pin and controls the Dot clock (DCLK) source. Note this bit is writeable as well as readable. Bit 3, This bit reflects the value sampled on MD[19] pin and controls the Graphics clock source. Bit 2, This bit reflects the value sampled on MD[18] pin and controls the Host/CPU clock source as follows: setting to ’0’: External. HCLK pin is an input, setting to ’1’: Internal. HCLK pin is an output and is connected to the internal frequency synthesizer output. Bit 1, This bit reflects the value sampled on MD[17] pin and controls the PCI clock output as follows: Setting to ’0’, the PCI clock output = HCLK / 3 Setting to ’1’, the PCI clock output = HCLK / 2 Bit 0, Reserved. This register defaults to the values sampled on MD[23] & MD[20:16] pins after reset. 13/55 Issue 1.1 STRAP OPTION 2.1.4 STRAP REGISTER 3 INDEX 3CH (STRAP3) Bits 7-0 of this register reflect the status of pins MD[47:40] respectively. They are use by the chip as follows: Bit 7-6, Reserved. Bit 5, UART2 internal or external. This bit reflects the value sampled on MD[45] pin and controls the UART2 I/F as follows: Setting to ’0’, UART2 is external. Setting to ’1’, UART2 is internal. Bit 4, UART1 internal or external and additional TFT outputs. This bit reflects the value sampled on MD[44] pin and controls the UART1 I/F and the additional TFT I/F as follows: Setting to ’0’, UART1 is external and an additional 6 TFT outputs (lowest bits - 2 red, 2 green and 2 blue) are enabled. Setting to ’1’, UART1 is internal. Note that when strap option testbus enabled (see Section 2.1.3 Strap Register 2 bit 0) is driven to 1 it takes priority over this strap which becomes meaningless. Bit 3, Parallel Port internal or external. This bit reflects the value sampled on MD[43] pin and controls the Parallel Port i/f as follows: Setting to ’0’, the Parallel Port is external Setting to ’1’, the Parallel Port is internal Bit 2, KB/Mouse internal or external. This bit reflects the value sampled on MD[42] pin and controls the KB/Mouse controller i/f as follows: Setting to ’0’, the KB/Mouse controller is external Setting to ’1’, the KB/Mouse controller is internal Bit 1, Local Bus i/f or ISA I/F. This bit reflects the value sampled on MD[41] pin and sets whether the Local Bus i/f or the ISA i/f is available at the device i/f as follows: Setting to ’0’, selectes the ISA I/F Setting to ’1’, selectec the Local Bus I/F Bit 0 PCMCIA I/F or PCI I/F. This bit reflects the value sampled on MD[40] pin and sets whether the PCMCIA i/f or the PCI i/f is available at the device i/f as follows: Setting to ’0’, selects the PCI I/F Setting to ’1’, selects the PCMCIA I/F This register defaults to the values sampled on MD[47:40] pins after reset. 14/55 Issue 1.1 STRAP OPTION 2.1.5 STRAP REGISTER 4 INDEX 3Dh (STRAP4) Bits 5-0 of this register reflect the status of pins MD[53:48] respectively. They are use by the chip as follows: Bits 7-5 Reserved. Bit 4, y.y V present on board. This bit reflects the value sampled on MD[52] pin and is used to notify the Cardbus socket management unit if the y.y V vcc voltage (where y.y is less than x.x) is present on board as follows Setting to ’0’, y.y V Vcc voltage is not available Setting to ’1’: y.y V Vcc voltage is available. Bit 3, x.x V present on board. This bit reflects the value sampled on MD[51] pin and is used to notify the Cardbus socket management unit if the x.x V vcc voltage (where x.x is less than 3.3) is present on board as follows: Setting to ’0’, x.x V Vcc voltage is not available. Setting to ’1’: x.x V Vcc voltage is available. Bit 2, 3.3 V present on board. This bit reflects the value sampled on MD[50] pin and is used to notify the Cardbus socket management unit if the 3.3 V vcc voltage is present on board as follows: Setting to ’0’, 3.3 V vcc voltage is not available. Setting to ’1’, 3.3 V vcc voltage is available. Bit 1, 5 V present on board. This bit reflects the value sampled on MD[49] pin and is used to notify the Cardbus socket management unit if the 5 V vcc voltage is present on board as follows: Setting to ’0’, 5 V vcc voltage is not available. Setting to ’1’, 5 V vcc voltage is available. Bit 0, This bit reflects the value sampled on MD[48] pin and is used to enable the TFT controller outputs on pads RFU0-RFU11 as follows: RFU0 : R[2] RFU1 : R[3] RFU2 : R[4] RFU3 : R[5] RFU4 : G[2] RFU5 : G[3] RFU6 : G[4] RFU7 : G[5] RFU8 : B[2] RFU9 : B[3] RFU10 : B[4] RFU11 : B[5] This register defaults to the values sampled on MD[53:48] pins after reset. 15/55 Issue 1.1 STRAP OPTION 2.1.6 HCLK PLL STRAP REGISTER 0 INDEX 5FH (HCLK_STRAP0) Bits 5-0 of this register reflect the status of pins MD[26:21] respectively. They are use by the chip as follows: Bits 7-6, Reserved. Bits 5-3, These pins reflect the value sampled on MD[26:24] pins respectively and control the Host clock frequency synthesizer. Bit 2-1, Reserved. Bit 0, Reserved. This register defaults to the values sampled on above pins after reset. 16/55 Issue 1.1 PIN DESCRIPTION 3 PIN DESCRIPTION 3.1. INTRODUCTION The STPC Industrial integrates most of the functionalities of the PC architecture. Therefore, many of the traditional interconnections between the host PC microprocessor and the peripheral devices are totally internal to the STPC Industrial. This offers improved performance due to the tight coupling of the processor core and it’s peripherals. As a result many of the external pin connections are made directly to the on-chip peripheral functions. Table 3-1. Signal Description Figure 3-1 shows the STPC Industrial’s external interfaces. It defines the main busses and their function. Table 3-1 describes the physical implementation listing signal types and their functionalities. Table 3-2 provides a full pin listing and description. Table 3-4 provides a full listing of the STPC Industrial package pin location physical connection. Please refer to the pin allocation drawing for reference. Due to the number of pins available for the package, and the number of functional I/Os, some pins have several functions, selectable by strap option on Reset. Table 3-3 provides a summary of these pins and their functions. Group name Basic Clocks, Reset & Xtal (SYS) DRAM Controller(DRAM) PCI Controller PC Card Interface Keyboard/Mouse Controller (SIO) Local Bus I/F, Parallel I/F, Serial 2 ISA Interface/IPC extensions Serial 1 (SIO) TFT output VGA Controller (VGA) Grounds VDD Analog specific VCC/VDD Reserved Total Pin Count Qty 13 89 55 64 64 4 75 73 8 24 75 26 10 74 16 16 1 388 Figure 3-1. STPC Industrial External Interfaces STPC Industrial x86 core PCI NORTH BRIDGE DRAM VGA 89 10 PC TFT CARD 24 12 55 SOUTH BRIDGE SYS ISA/ LOCAL BUS SIO 13 75 38 17/55 Issue 1.1 PIN DESCRIPTION Table 3-2. Definition of Signal Pins Signal Name Dir BASIC CLOCKS AND RESETS SYSRSTI#* I SYSRSTO#* O XTALI I XTALO O PCI_CLKI* I PCI_CLKO O ISA_CLK, ISA_CLK2X O CLK14M O HCLK* I/O DEV_CLK* O GCLK2X I/O DCLK I/O VDD_xxx_PLL System Reset / Power good Reset Output to System 14.3MHz Crystal Input 14.3MHz Crystal Output 33MHz PCI/CardBus Input Clock 33MHz PCI/CardBus Output Clock ISA Clock x1 and x2 (also Multiplexer Select Line For IPC) ISA bus synchronisation clock 33 / 66MHz Host Clock (Test) 24MHz Peripheral Clock 80MHz Graphics Clock 135MHz Dot Clock Power Supply for PLL Clocks 1 1 1 1 1 1 2 1 1 1 1 1 MEMORY INTERFACE MA[11:0] RAS#[3:0] CAS#[7:0] MWE# MD[63:0] Memory Address Row Address Strobe Column Address Strobe Write Enable Memory Data 12 4 8 1 64 WITH ISA BUS ) Address Bus [21:0] Data Bus [15:0] Ready Memory and I/O Write signals Memory and I/O Read signals Flash Memory and I/O Chip Select 22 16 1 2 2 6 I/O O O O I/O LOCAL BUS INTERFACE (COMBINED PA[21:0]* O PD[15:0]* I/O PRDY#* I PWR#[1:0]* O PRD#[1:0]* O FCS#[1:0]*, IOCS#[3:0]* O Description Qty ISA BUS INTERFACE (COMBINED WITH LOCAL BUS, PARALLEL PORT, SERIAL INTERFACE) LA[23:17]* O Unlatched Address SA[19:0]* O Latched Address SD[15:0]* I/O Data Bus 7 20 16 IOCHRDY* ALE* BHE#* MEMR#*, MEMW#* SMEMR#*, SMEMW#* IOR#*, IOW#* MASTER#* MCS16#*, IOCS16#* REF#* AEN* IOCHCK#* I O O I/O O I/O I I I O I I/O Channel Ready Address Latch Enable System Bus High Enable Memory Read & Write System Memory Read and Write I/O Read and Write Add On Card Owns Bus Memory Chip Select 16, I/O Chip Select 16 Refresh Cycle Address Enable I/O Channel Check (ISA) 1 1 1 2 2 2 1 2 1 1 1 RTCRW#* RTCDS#* RTCAS#* O O O RTC Read / Write# RTC Data Strobe RTC Address Strobe 1 1 1 18/55 Issue 1.1 PIN DESCRIPTION Table 3-2. Definition of Signal Pins Signal Name RMRTCCS#* GPIOCS#* IRQ_MUX[3:0]* DACK_ENC[2:0]* DREQ_MUX[1:0]* TC* Dir O I/O I O I O KEYBOARD & MOUSE INTERFACE KBDATA*, MDATA* I KBCLK*, MCLK* O Description ROM / RTC Chip Select General Purpose Chip Select Multiplexed Interrupt Request DMA Acknowledge Multiplexed DMA Request ISA Terminal Count Keyboard & Mouse Data Line Keyboard & Mouse Clock Line Qty 1 1 4 3 2 1 2 2 SERIAL INTERFACE (SERIAL 1 COMBINED WITH TFT INTERFACE / SERIAL 2 COMBINED WITH IPC ) SIN1*, SIN2* I Serial Data In (Serial 1, 2) 2 SOUT1*, SOUT2* O Serial Data Out (Serial 1, 2) 2 CTS1#*, CTS2#* I Clear To Send (Serial 1, 2) 2 RTS1#*, RTS2#* O Request To Send (Serial 1, 2) 2 DSR1#*, DSR2#* I Data Set Ready (Serial 1, 2) 2 DTR1#*, DTR2#* O Data Terminal Ready (Serial 1,2) 2 DCD1#*, DCD2#* I Data Carrier Detect (Serial 1, 2) 2 RI1#*, RI2#* I Ring Indicator (Serial 1, 2) 2 PARALLEL PORT (COMBINED WITH ISA BUS AND IPC) PE* I Paper End SLCT* I SELECT BUSY#* I BUSY ERR#* I ERROR ACK#* I Acknowledge PDDIR#* O Parallel Device Direction STROBE#* O PCS / STROBE# INIT#* O INIT AUTPFDX#* O Automatic Line Feed SLCTIN#* O SELECT IN PPD[7:0]* I/O Data Bus 1 1 1 1 1 1 1 1 1 1 8 PCMCIA INTERFACE (COMBINED WITH PCI / CARDBUS) RESET* O Reset A[25:0]* O Address Bus D[15:0]* I/O Data Bus IORD#*, IOWR#* O I/O Read and Write DREQ#* / WP* / IOIS16#* I DMA Request // Write Protect // I/O Size is 16 bit BVD1*, BVD2* I Battery Voltage Detect READY#*/BUSY#*/IREQ#* I Ready / Busy // Interrupt Request WAIT#* I Wait INPACK#* I Input Port Acknowledge OE#* / TCw* O Output Enable // DMA Terminal Count 1 26 16 2 1 2 1 1 1 1 WE#* / TCr* DACK* / REG#* CD1#*, CD2#* 1 1 2 O O I Write Enable // DMA Terminal Count DMA Acknowledge // Register Card Detect 19/55 Issue 1.1 PIN DESCRIPTION Table 3-2. Definition of Signal Pins Signal Name CE1#*, CE2#* VS1#*, VS2#* VCC5_EN* VCC3_EN* VPP_PGM* VPP_VCC* Dir O I O O O O Description Card Enable Voltage Sense Power Switch control Power Switch control Power Switch control Power Switch control : 5v power : 3.3v power : Program power : VCC power Qty 2 2 1 1 1 1 CARDBUS INTERFACE (COMBINED WITH PCI / PCMCIA) CCLKRUN* I/O Clock CRST#* O Reset CSTSCHG#* I System Change CAD[31:0]* I/O Address / Data CBE[3:0]* I/O Bus Commands / Byte Enables CFRAME#* I/O Cycle Frame CTRDY#* I/O Target Ready CIRDY#* I/O Initiator Ready CSTOP#* I/O Stop Transaction CDEVSEL#* I/O Device Select CPAR* I/O Parity Signal Transactions CSERR#* I System Error CPERR#* I/O Parity Error CBLOCK#* I/O PCI Lock CCD[2:1]* I Card Detect CINT#* I Interrupt Request CREQ#* I Request CGNT#* O Grant 1 1 1 32 4 1 1 1 1 1 1 1 1 1 2 1 1 1 PCI INTERFACE (COMBINED AD[31:0]* BE[3:0]* FRAME#* TRDY#* IRDY#* STOP#* WITH PCMCIA / CARDBUS) I/O Address / Data I/O Bus Commands / Byte Enables I/O Cycle Frame I/O Target Ready I/O Initiator Ready I/O Stop Transaction 32 4 1 1 1 1 DEVSEL#* PAR* SERR#* LOCK#* PCI_REQ#[2:0]* PCI_GNT#[2:0]* PCI_INT[3:0]* I/O I/O O I I O I 1 1 1 1 3 3 4 Device Select Parity Signal Transactions System Error PCI Lock PCI Request PCI Grant PCI Interrupt Request 20/55 Issue 1.1 PIN DESCRIPTION Table 3-2. Definition of Signal Pins Signal Name MONITOR INTERFACE RED, GREEN, BLUE VSYNC* HSYNC* VREF_DAC RSET COMP DDC[1:0]* SCL / DDC[1]* SDA / DDC[0]* Dir TFT INTERFACE (COMBINED R[5:0], G[5:0], B[5:0] FPLINE FPFRAME DE ENAVDD ENVCC PWM WITH SERIAL 1) O Red, Green, Blue O Horizontal Sync O Vertical Sync O Data Enable O Enable Vdd of flat panel O Enable Vcc of flat panel O PWM back-light control MISCELLANEOUS SPKRD* SCAN_ENABLE O I/O I/O I I I I/O I/O I/O O I Description Red, Green, Blue Vertical Sync Horizontal Sync DAC Voltage reference Resistor Set Compensation Display Data Channel Serial Link I C Interface - Clock / Can be used for VGA DDC[1] signal I C Interface - Data / Can be used for VGA DDC[0] signal Speaker Device Output Test Pin - Reserved Qty 3 1 1 1 1 1 2 1 1 18 1 1 1 1 1 1 1 1 Note; *denotes theat the pin is V 5T (see Section 4 ) 21/55 Issue 1.1 PIN DESCRIPTION 3.2. SIGNAL DESCRIPTIONS 3.2.2 BASIC CLOCKS AND RESETS SYSRSTI# System Reset/Power good. This input is low when the reset switch is depressed. Otherwise, it reflects the power supply’s power good signal. PWGD is asynchronous to all clocks, and acts as a negative active reset. The reset circuit initiates a hard reset on the rising edge of PWGD. SYSRSTO# Reset Output to System. This is the system reset signal and is used to reset the rest of the components (not on Host bus) in the system. The ISA bus reset is an externally inverted buffered version of this output and the PCI bus reset is an externally buffered version of this output. CLK14M ISA bus synchronisation clock. This is the buffered 14.318 Mhz clock to the ISA bus. This clock also provides the reference clock to the frequency synthesizer that generates GCLK2X and DCLK. HCLK Host Clock. This is the host 1X clock. Its frequency can vary from 50 to 75 MHz. All host transactions and PCI transactions are synchronized to this clock. Host transactions executed by the DRAM controller are also driven by this clock. DEV_CLK 24MHz Peripheral Clock (floppy drive). This 24MHZ signal is provided as a convenience for the system integration of a Floppy Disk driver function in an external chip. XTALI 14.3MHz Crystal Input XTALO 14.3MHz Crystal Output. These pins are the 14.318 MHz crystal input; This clock is used as the reference clock for the internal frequency synthesizer to generate the HCLK and CLK24M. A 14.318 MHz Series Cut Quartz Crystal should be connected between these two pins. Balance capacitors of 15 pF should also be added. In the event of an external oscillator providing the master clock signal to the STPC Industrial device, the TTL signal should be provided on XTALO. GCLK2X 80MHz Graphics Clock. This is the Graphics 2X clock, which drives the graphics engine and the DRAM controller to execute the graphics and display cycles. Normally GCLK2X is generated by the internal frequency synthesizer, and this pin is an output. By setting a bit in Strap Register 2, this pin can be made an input so that an external clock can replace the internal frequency synthesizer. PCI_CLKI 33MHz PCI Input Clock This signal must be connected to a clock generator and is usually connected to PCI_CLKO. DCLK 135MHz Dot Clock. This is the dot clock, which drives graphics display cycles. Its frequency can be as high as 135 MHz, and it is required to have a worst case duty cycle of 60-40. For further details, refer to Section 2.1.3 bit 4. PCI_CLKO 33MHz PCI Output Clock. This is the master PCI bus clock output 3.2.3 MEMORY INTERFACE ISA_CLK ISA Clock Output (also Multiplexer Select Line For IPC). This pin produces the Clock signal for the ISA bus. It is also used with ISA_CLK2X as the multiplexor control lines for the Interrupt Controller Interrupt input lines. This is a divided down version of the PCICLK or OSC14M. ISA_CLKX2 ISA Clock Output (also Multiplexer Select Line For IPC). This pin produces a signal at twice the frequency of the ISA bus Clock signal. It is also used with ISA_CLK as the multiplexor control lines for the Interrupt Controller Interrupt input lines. 22/55 Issue 1.1 MA[11:0] Memory Address. These 12 multiplexed memory address pins support external DRAM with up to 4K refresh. These include all 16M x N and some 4M x N DRAM modules. The address signals must be externally buffered to support more than 16 DRAM chips. The timing of these signals can be adjusted by software to match the timings of most DRAM modules. MD[63:0] Memory Data. This is the 64-bit memory data bus. If only half of a bank is populated, MD63-32 is pulled high, data is on MD31-0. MD20-0 are also used as inputs at the rising edge of PWGD to latch in power-up configuration information into the ADPC strap registers. PIN DESCRIPTION RAS#[3:0] Row Address Strobe. There are 4 active low row address strobe outputs, one each for each bank of the memory. Each bank contains 4 or 8-Bytes of data. The memory controller allows half of a bank (4-Bytes) to be populated to enable memory upgrade at finer granularity. The RAS# signals drive the SIMMs directly without any external buffering. These pins are always outputs, but they can also simultaneously be inputs, to allow the memory controller to monitor the value of the RAS# signals at the pins. CAS#[7:0] Column Address Strobe. There are 8 active low column address strobe outputs, one each for each Byte of the memory. The CAS# signals drive the SIMMs either directly or through external buffers. These pins are always outputs, but they can also simultaneously be inputs, to allow the memory controller to monitor the value of the CAS# signals at the pins. MWE# Write Enable. Write enable specifies whether the memory access is a read (MWE# = H) or a write (MWE# = L). This single write enable controls all DRAMs. It can be externally buffered to boost the maximum number of loads (DRAM chips) supported. The MWE# signals drive the SIMMs directly without any external buffering. 3.2.4 LOCAL BUS INTERFACE (Combined with ISA Bus) PA[21:0] Memory Address. This is the 22-bit Local Bus Address PD[15:0] Data Bus. This is the 16-bit bidirectional Local Bus Data bus. PRDY# Ready. This input signals the Local Bus Ready state. PWR#1 Memory and I/O Write signal for MS Byte PWR#0 Memory and I/O Write signal for LS Byte. PRD#1 Memory and I/O Read signals for MS Byte. PRD#0 Memory and I/O Read signals for LS Byte. FCS#[1:0], IOCS#[3:0] Flash Memory and I/O Chip select. 3.2.5 ISA BUS INTERFACE LA[23:17] Unlatched Address. These unlatched ISA Bus pins address bits 23-17 on 16-bit devices. When the ISA bus is accessed by any cycle initiated from the PCI bus, these pins are in output mode. When an ISA bus master owns the bus, these pins are tristated. SA[19:0] Unlatched Address. These are the 20 low bits of the system address bus of ISA. These pins are used as an input when an ISA bus master owns the bus and are outputs at all other times. SD[15:0] I/O Data Bus (ISA). These are the external ISA databus pins. IOCHRDY IO Channel Ready. IOCHRDY is the IO channel ready signal of the ISA bus and is driven as an output in response to an ISA master cycle targeted to the host bus or an internal register of the STPC Industrial. The STPC Industrial monitors this signal as an input when performing an ISA cycle on behalf of the host CPU, DMA master or refresh. ISA masters which do not monitor IOCHRDY are not guaranteed to work with the STPC Industrial since the access to the system memory can be considerably delayed due to CRT refresh or a write back cycle. ALE Address Latch Enable. This is the address latch enable output of the ISA bus and is asserted by the STPC Industrial to indicate that LA23-17, SA19-0, AEN and SBHE# signals are valid. The ALE is driven high during refresh, DMA master or an ISA master cycles by the STPC Industrial. ALE is driven low after reset. BHE# System Bus High Enable. This signal, when asserted, indicates that a data Byte is being transferred on SD15-8 lines. It is used as an input when an ISA master owns the bus and is an output at all other times. MEMR# Memory Read. This is the memory read command signal of the ISA bus. It is used as an input when an ISA master owns the bus and is an output at all other times. The MEMR# signal is active during refresh. MEMW# Memory Write. This is the memory write command signal of the ISA bus. It is used as an input when an ISA master owns the bus and is an output at all other times. 23/55 Issue 1.1 PIN DESCRIPTION SMEMR# System Memory Read. The STPC Industrial generates SMEMR# signal of the ISA bus only when the address is below one MByte or the cycle is a refresh cycle. SMEMW# System Memory Write. The STPC Industrial generates SMEMW# signal of the ISA bus only when the address is below one MByte. IOR# I/O Read. This is the IO read command signal of the ISA bus. It is an input when an ISA master owns the bus and is an output at all other times. IOW# I/O Write. This is the IO write command signal of the ISA bus. It is an input when an ISA master owns the bus and is an output at all other times. MASTER# Add On Card Owns Bus. This signal is active when an ISA device has been granted bus ownership. MCS16# Memory Chip Select16. This is the decode of LA23-17 address pins of the ISA address bus without any qualification of the command signal lines. MCS16# is always an input. The STPC Industrial ignores this signal during IO and refresh cycles. IOCS16# IO Chip Select16. This signal is the decode of SA15-0 address pins of the ISA address bus without any qualification of the command signals. The STPC Industrial does not drive IOCS16# (similar to PC-AT design). An ISA master access to an internal register of the STPC Industrial is executed as an extended 8-bit IO cycle. REF# Refresh Cycle. This is the refresh command signal of the ISA bus. It is driven as an output when the STPC Industrial performs a refresh cycle on the ISA bus. It is used as an input when an ISA master owns the bus and is used to trigger a refresh cycle. The STPC Industrial performs a pseudo hidden refresh. It requests the host bus for two host clocks to drive the refresh address and capture it in external buffers. The host bus is then relinquished while the refresh cycle continues on the ISA bus. AEN Address Enable. Address Enable is enabled when the DMA controller is the bus owner to indicate that a DMA transfer will occur. The enabling of the signal indicates to IO devices to ignore the IOR#/IOW# signal during DMA transfers. 24/55 Issue 1.1 IOCHCK# IO Channel Check. IO Channel Check is enabled by any ISA device to signal an error condition that can not be corrected. NMI signal becomes active upon seeing IOCHCK# active if the corresponding bit in Port B is enabled. GPIOCS# I/O General Purpose Chip Select 1. This output signal is used by the external latch on ISA bus to latch the data on the SD[7:0] bus. The latch can be use by PMU unit to control the external peripheral devices to power down or any other desired function. This pin is also serves as a strap input during reset. RTCRW# Real Time Clock RW#. This pin is used as RTCRW#. This signal is asserted for any I/O write to port 71h. RTCDS# Real Time Clock DS. This pin is used as RTCDS. This signal is asserted for any I/O read to port 71h. RTCAS# Real time clock address strobe. This signal is asserted for any I/O write to port 70h. RMRTCCS# ROM/Real Time clock chip select. This pin is a multi-function pin. This signal is asserted if a ROM access is decoded during a memory cycle. It should be combined with MEMR# or MEMW# signals to properly access the ROM. During an IO cycle, this signal is asserted if access to the Real Time Clock (RTC) is decoded. It should be combined with IOR# or IOW# signals to properly access the real time clock. IRQ_MUX[3:0] Multiplexed Interrupt Request. These are the ISA bus interrupt signals. They are to be encoded before connection to the STPC Industrial using ISACLK and ISACLKX2 as the input selection strobes. Note that IRQ8B, which by convention is connected to the RTC, is inverted before being sent to the interrupt controller, so that it may be connected directly to the IRQ# pin of the RTC. PIN DESCRIPTION 3.2.6 IPC (Combined with Serial Interface) RI1#, RI2# Input Ring indicator. DACK_ENC[2:0] DMA Acknowledge. These are the ISA bus DMA acknowledge signals. They are encoded by the STPC Industrial before output and should be decoded externally using ISACLK and ISACLKX2 as the control strobes. DSR1#, DSR2# Input Data set ready. CTS1#, CTS2# Input Clear to send. RTS1#, RTS2# Output Request to send. DREQ_MUX[1:0] ISA Bus Multiplexed DMA Request. These are the ISA bus DMA request signals. They are to be encoded before connection to the STPC Industrial using ISACLK and ISACLKX2 as the input selection strobes. TC ISA Terminal Count. This is the terminal count output of the DMA controller and is connected to the TC line of the ISA bus. It is asserted during the last DMA transfer, when the Byte count expires. DTR1#, DTR2# Output Data terminal read. 3.2.9 PARALLEL PORT (Combined with ISA Bus an IPC) PE Paper End. Input status signal from printer. 3.2.7 KEYBOARD/MOUSE INTERFACE SLCT Printer Select. Printer selected input. KBCLK, Keyboard Clock line. Keyboard data is latched by the controller on each negative clock edge produced on this pin. The keyboard can be disabled by pulling this pin low by software control. BUSY# Printer Busy. Input status signal from printer. KBDATA, Keyboard Data Line. 11-bits of data are shifted serially through this line when data is being transferred. Data is synchronised to KBCLK. MCLK, Mouse Clock line. Mouse data is latched by the controller on each negative clock edge produced on this pin. The mouse can be disabled by pulling this pin low by software control. ERR# Error. Input status signal from printer. ACK# Acknowledge. Input status signal from printer. PDDIR# Parallel Device Direction. Bidirectional control line output. STROBE# PCS/Strobe#. Data transfer strobe line to printer. MDATA, Mouse Data Line. 11-bits of data are shifted serially through this line when data is being transferred. Data is synchronised to MCLK. INIT# Initialize Printer. This output sends an initialize command to the connected printer. 3.2.8 SERIAL INTERFACE (Serial 1 combined with TFT Interface) (Serial 2 combined with IPC) AUTPFDX# Automatic Line feed. This output sends a command to the connected printer to automatically generate line feed on received carriage returns. SIN1, SIN2 Input Serial input. Data is clocked in using RCLK/16. SOUT1, SOUT2 Serial Output. Data is clocked out using TCLK/16 (TCLK=BAUD#). SLCTIN# Select In. Printer select output. PPD[7-0] Printer Data Lines Data transfer lines to printer. Bidirectional depending on modes. DCD1#, DCD2# Input Data carrier detect. 25/55 Issue 1.1 PIN DESCRIPTION WE#/PRGM# Write Enable. This output is used by the host for gating Memory Write data. WE# is also used for memory PC Cards that have programmable memory. 3.2.10 PCMCIA INTERFACE (Combined with PCI / Cardbus) RESET Card Reset. This output forces a hard reset to a PC Card. A[25:0] Address Bus. These are the 25 low bits of the system address bus of the PCMCIA bus. These pins are used as an input when an PCMCIA bus owns the bus and are outputs at all other times. D[15:0] I/O Data Bus (PCMCIA). These are the external PCMCIA databus pins. CA[25-0] Card Address. Used with the lower 11 bits of the ISA Address Bus to generate the Card Address. IORD# I/O Read. This output is used with REG# to gate I/O read data from the PC Card, (only when REG# is asserted). IOWR# I/O Write. This output is used with REG# to gate I/O write data from the PC Card, (only when REG# is asserted). WP Write Protect. This input indicates the status of the Write Protect switch (if fitted) on memory PC Cards (asserted when the switch is set to write protect). BVD1, BVD2 Battery Voltage Detect. These inputs will be generated by memory PC Cards that include batteries and are an indication of the condition of the batteries. BVD1 and BVD2 are kept asserted high when the battery is in good condition. READY#/BUSY#/IREQ# Ready/busy/Interupt request. This input is driven low by memory PC Cards to signal that their circuits are busy processing a previous write command. WAIT# Bus Cycle Wait. This input is driven by the PC Card to delay completion of the memory or I/O cycle in progress. OE# Output Enable. OE# is an active low output which is driven to the PC Card to gate Memory Read data from memory PC Cards. 26/55 Issue 1.1 REG# Attribute Memory Select. This output is inactive (high) for all normal accesses to the Main Memory of the PC Card. I/O PC Cards will only respond to IORD# or IOWR# when REG# is active (low). Also see Section 3.2.6 CD1#, CD2# Card Detect. These inputs provide for the detection of correct card insertion. CD#1 and CD#2 are positioned at opposite ends of the connector to assist in the detection process. These inputs are internally grounded on the PC Card therefore they will be forced low whenever a card is inserted in a socket. CE1#, CE2# Card Enable. These are active low output signals provided from the PCIC. CE#1 enables even Bytes, CE#2 odd Bytes. ENABLE# Enable. This output is used to activate/ select a PC Card socket. ENABLE# controls the external address buffer logic.C card has been detected (CD#1 and CD#2 = ’0’). ENIF# ENIF. This output is used to activate/select a PC Card socket. EXT_DIR EXternal Transreceiver Direction Control. This output is high during a read and low during a write. The default power up condition is write (low). Used for both Low and High Bytes of the Data Bus. VCC_EN#, VPP1_EN0, VPP1_EN1, VPP 2_EN0, VPP2_EN1 Power Control. Five output signals used to control voltages (VPP1, VPP2 and VCC) to a PC Card socket. Also see Section 16.7.5 GPI# General Purpose Input. This signal is hardwired to 1. PIN DESCRIPTION DEVSEL# I/O Device Select. This signal is used as an input when the STPC Industrial initiates a bus cycle on the PCI bus to determine if a PCI slave device has decoded itself to be the target of the current transaction. It is asserted as an output either when the STPC Industrial is the target of the current PCI transaction or when no other device asserts DEVSEL# prior to the subtractive decode phase of the current PCI transaction. 3.2.11 CARDBUS INTERFACE (Combined with PCI / PCMCIA) For card bus pinouts, refer to the PCI pinout. 3.2.12 PCI INTERFACE AD[31:0] PCI Address/Data. This is the 32-bit multiplexed address and data bus of the PCI. This bus is driven by the master during the address phase and data phase of write transactions. It is driven by the target during data phase of read transactions. BE[3:0]# Bus Commands/Byte Enables. These are the multiplexed command and Byte enable signals of the PCI bus. During the address phase they define the command and during the data phase they carry the Byte enable information. These pins are inputs when a PCI master other than the STPC Industrial owns the bus and outputs when the STPC Industrial owns the bus. FRAME# Cycle Frame. This is the frame signal of the PCI bus. It is an input when a PCI master owns the bus and is an output when STPC Industrial owns the PCI bus. TRDY# Target Ready. This is the target ready signal of the PCI bus. It is driven as an output when the STPC Industrial is the target of the current bus transaction. It is used as an input when STPC Industrial initiates a cycle on the PCI bus. IRDY# Initiator Ready. This is the initiator ready signal of the PCI bus. It is used as an output when the STPC Industrial initiates a bus cycle on the PCI bus. It is used as an input during the PCI cycles targeted to the STPC Industrial to determine when the current PCI master is ready to complete the current transaction. STOP# Stop Transaction. STOP# is used to implement the disconnect, retry and abort protocol of the PCI bus. It is used as an input for the bus cycles initiated by the STPC Industrial and is used as an output when a PCI master cycle is targeted to the STPC Industrial. PAR Parity Signal Transactions. This is the parity signal of the PCI bus. This signal is used to guarantee even parity across AD[31:0], CBE[3:0]#, and PAR. This signal is driven by the master during the address phase and data phase of write transactions. It is driven by the target during data phase of read transactions. (Its assertion is identical to that of the AD bus delayed by one PCI clock cycle) SERR# System Error. This is the system error signal of the PCI bus. It may, if enabled, be asserted for one PCI clock cycle if target aborts a STPC Industrial initiated PCI transaction. Its assertion by either the STPC Industrial or by another PCI bus agent will trigger the assertion of NMI to the host CPU. This is an open drain output. LOCK# PCI Lock. This is the lock signal of the PCI bus and is used to implement the exclusive bus operations when acting as a PCI target agent. PCI_REQ#[2:0] PCI Request. These pins are the three external PCI master request pins. They indicates to the PCI arbiter that the external agents desire use of the bus. PCI_GNT#[2:0] PCI Grant. These pins indicate that the PCI bus has been granted to the master requesting it on its PCI_REQ#. PCI_INT[3:0] PCI Interrupt Request. These are the PCI bus interrupt signals. They are to be encoded before connection to the STPC Industrial using ISACLK and ISACLKX2 as the input selection strobes. 3.2.13 MONITOR INTERFACE RED, GREEN, BLUE RGB Video Outputs. These are the 3 analog color outputs from the RAMDACs VSYNC Vertical Synchronisation Pulse. This is the vertical synchronization signal from the VGA controller. 27/55 Issue 1.1 PIN DESCRIPTION HSYNC Horizontal Synchronisation Pulse. This is the horizontal synchronization signal from the VGA controller. VREF_DAC DAC Voltage reference. This pin is an input driving the digital to analog converters. This allows an external voltage reference source to be used. RSET Resistor Current Set. This is the reference current input to the RAMDAC. Used to set the fullscale output of the RAMDAC. COMP Compensation. This is the RAMDAC compensation pin. Normally, an external capacitor (typically 10nF) is connected between this pin and VDD to damp oscillations. DDC[1:0] Direct Data Channel Serial Link. These bidirectional pins are connected to CRTC register 3Fh to implement DDC capabilities. They conform to I2C electrical specifications, they have opencollector output drivers which are internally connected to VDD through pull-up resistors. They can instead be used for accessing I C devices on board. DDC1 and DDC0 correspond to SCL and SDA respectively. 28/55 Issue 1.1 3.2.14 FLAT PANEL INTERFACE SIGNALS (Combined with Serial 1) FPFRAME, Vertical Sync. pulse Output. FPLINE, Horizontal Sync. Pulse Output. DE, Data Enable. R5-0, Red Output. G5-0, Green Output. B5-0, Blue Output. ENAVDD Enable VDD of Flat Panel. ENVCC Enable VCC of Flat Panel. PWM PWM Back-Light Control. 3.2.15 MISCELLANEOUS SPKRD Speaker Drive. This is the output to the speaker and is the AND of the counter 2 output with bit 1 of Port 61h and drives an external speaker driver. This output should be connected to a 7407 type high voltage driver. SCAN_ENABLE Reserved. This pin is reserved for Test and Miscellaneous functions. It has to be set to ‘0’ or connected to ground in normal operation. PIN DESCRIPTION Table 3-3. Signals sharing the same pin ISA BUS / IPC LOCAL BUS LA[23:22] FCS#[0], PRD#[1] LA[21:20] PA[21:20] LA[19:17] PRD#[0], PWR#[1:0] SA[19:1] PA[19:1] SA[0] PRDY# SD[15:0] PD[15:0] BHE# FCS#[1] MEMR#, MEMW# IOCS[3:2] SMEMR#, SMEMW# IOCS[1:0] PARALLEL PORT GPIOCS# PE IOCHRDY SLCT IOR# BUSY# IOW# ERR# MASTER# ACK# MCS16# PDDIR# IOCS16# INIT# REF# AUTPFDX# AEN SLCTIN# IOCHCK# PPD[7] RTCRW# PPD[5] RTCDS# PPD[4] RTCAS# PPD[3] RMRTCCS# PPD[2] ALE PPD[1] SERIAL INTERFACE DACK_ENC[0:2] DCD2#, DSR2#, SIN2 DREQ_MUX[0:1] CTS2#, RTS2# TC SOUT2 TFT INTERFACE SERIAL 1 B[0,1] DCD1#, CTS1# G[0,1] DSR1#, RTS1# R[0,1] SIN1, SOUT1 PCI CARDBUS PCMCIA CCLK A[16] CRST# RESET AD[31:27] CAD[31:27] D[10,9,1,8,0] AD[26:20] CAD[26:20] A[0:6] 29/55 Issue 1.1 PIN DESCRIPTION PCI CARDBUS PCMCIA AD[19] CAD[19] A[25] AD[18] CAD[18] A[7] AD[17] CAD[17] A[24] AD[16] CAD[16] A[17] AD[15] CAD[15] IOWR# AD[14] CAD[14] A[9] AD[13] CAD[13] IORD# AD[12] CAD[12] A[11] AD[11] CAD[11] OE# / TCw AD[10] CAD[10] CE[2] AD[9] CAD[9] A[10] AD[8:0] CAD[8:0] D[15,7,13,6,12,5,11,4,3] BE[3] CBE[3] DACK/REG# BE[2] CBE[2] A[12] BE[1] CBE[1] A[8] BE[0] CBE[0] CE[1] FRAME# CFRAME# A[23] TRDY# CTRDY# A[22] IRDY# CIRDY# A[15] STOP# CSTOP# A[20] DEVSEL# CDEVSEL# A[21] PAR CPAR A[13] CPERR# A[14] SERR# CSERR# WAIT LOCK# CBLOCK# A[19] PCIREQ#[2] CREQ# INPACK# PCIREQ#[1] CCD1 CD1# PCIREQ#[0] CSTSCHG# BVD1 PCIGNT#[2] CGNT# WE# / TCr PCIGNT#[1] CCD2 CD2# PCIGNT#[0] BVD2 PCI_INT[3] VCC3_EN PCI_INT[2] VCC5_EN PCI_INT[1] VPP_PGM PCI_INT[0] CINT# READY# CLKRUN DREQ# / WP / IOIS16# A[18] 30/55 Issue 1.1 PIN DESCRIPTION Table 3-4. Pinout. Pin # Pin name Pin # Pin name Pin # Pin name AE22 MD[4] N25 MD[48] C4 SYSRSTI# AF22 MD[5] N23 MD[49] A3 SYSRSTO# AD21 MD[6] N26 MD[50] AB25 XTALI AE23 MD[7] P24 MD[51] AB23 XTALO AC22 MD[8] M25 MD[52] G25 PCI_CLKI AF23 MD[9] N24 MD[53] H23 PCI_CLKO AD22 MD[10] M26 MD[54] B20 ISA_CLK AE24 MD[11] L25 MD[55] A20 ISA_CLK2X AD23 MD[12] M24 MD[56] AC26 CLK14M AF24 MD[13] L26 MD[57] H26 HCLK AE26 MD[14] M23 MD[58] J26 DEV_CLK AD25 MD[15] K25 MD[59] AC15 GCLK2X AD26 MD[16] L24 MD[60] AD16 DCLK AC25 MD[17] K26 MD[61] AC24 MD[18] K23 MD[62] J25 MD[63] B1 PA[0] AE13 MA[0] AB24 MD[19] AC12 MA[1] AB26 MD[20] AF13 MA[2] AA25 MD[21] AD12 MA[3] Y23 MD[22] AE14 MA[4] AA24 MD[23] P1 LA[17] / PWR#[0] AC14 MA[5] AA26 MD[24] N3 LA[18] / PWR#[1] AF14 MA[6] Y25 MD[25] R2 LA[19] / PRD#[0] AD13 MA[7] Y26 MD[26] C1 LA[20] / PA[20] AE15 MA[8] Y24 MD[27] C2 LA[21] / PA[21] AD14 MA[9] W25 MD[28] P3 LA[22] / PRD#[1] AF15 MA[10] V23 MD[29] R1 LA[23] / FCS#[0] AE16 MA[11] W26 MD[30] P4 SA[0] / PRDY# AD15 RAS#[0] W24 MD[31] J2 SA[1] / PA[1] AF16 RAS#[1] V25 MD[32] H3 SA[2] / PA[2] AC17 RAS#[2] V26 MD[33] H1 SA[3] / PA[3] AE18 RAS#[3] U25 MD[34] J4 SA[4] / PA[4] AD17 CAS#[0] V24 MD[35] H2 SA[5] / PA[5] AF18 CAS#[1] U26 MD[36] G3 SA[6] / PA[6] AE19 CAS#[2] U23 MD[37] G1 SA[7] / PA[7] AF19 CAS#[3] T25 MD[38] G2 SA[8] / PA[8] AD18 CAS#[4] U24 MD[39] F1 SA[9] / PA[9] AE20 CAS#[5] T26 MD[40] F3 SA[10] / PA[10] AC19 CAS#[6] R25 MD[41] G4 SA[11] / PA[11] AF20 CAS#[7] R26 MD[42] F2 SA[12] / PA[12] AD19 MWE# T24 MD[43] E1 SA[13] / PA[13] AE21 MD[0] P25 MD[44] E3 SA[14] / PA[14] AC20 MD[1] R23 MD[45] E4 SA[15] / PA[15] AF21 MD[2] P26 MD[46] E2 SA[16] / PA[16] AD20 MD[3] R24 MD[47] D1 SA[17] / PA[17] 31/55 Issue 1.1 PIN DESCRIPTION Pin # Pin name Pin # Pin name Pin # Pin name D3 SA[18] / PA[18] C5 IRQ_MUX[2] B12 A[17] D2 SA[19] / PA[19] B3 IRQ_MUX[3] C13 A[18] P2 SD[0] / PD[0] AD1 SPKRD A12 A[19] M3 SD[1] / PD[1] V3 DACK_ENC[0]/DCD2# B11 A[20] N1 SD[2] / PD[2] Y2 DACK_ENC[1]/DSR2# A11 A[21] M4 SD[3] / PD[3] W4 DACK_ENC[2] / SIN2 D12 A[22] N2 SD[4] / PD[4] Y1 DREQ_MUX[0]/CTS2# B10 A[23] L3 SD[5] / PD[5] W3 DREQ_MUX[1]/RTS2# C11 A[24] M1 SD[6] / PD[6] AA2 TC / SOUT2 A10 A[25] M2 SD[7] / PD[7] L1 SD[8] / PD[8] Y4 K3 SD[9] / PD[9] L2 SD[10] / PD[10] K4 K1 D10 D[0] DTR2# B9 D[1] AA1 RI2# C10 D[2] U4 SIN1 / R[0] A9 D[3] SD[11] / PD[11] V1 SOUT1 / R[1] B8 D[4] SD[12] / PD[12] V2 CTS1 / B[1] C9 D[5] J3 SD[13] / PD[13] U3 RTS1# / G[1] B7 D[6] K2 SD[14] / PD[14] U1 DSR1# / G[0] D8 D[7] J1 SD[15] / PD[15] W2 DTR1# A7 D[8] T2 BHE# / FCS#[1] T3 DCD1# / B[0] B6 D[9] R3 MEMR# / IOCS#[3] W1 RI1# D7 D[10] T1 MEMW# / IOCS#[2] A6 D[11] R4 SMEMR# / IOCS#[1] F25 KBCLK C7 D[12] U2 SMEMW# / IOCS#[0] F26 KBDATA A5 D[13] AB2 IOCHRDY / SLCT G24 MCLK C6 D[14] AB1 IOR# / BUSY# G23 MDATA B4 D[15] Y3 GPIOCS# / PE B22 IORD# AA3 IOW# / ERR# D18 RESET D22 IOWR# AC2 MASTER# / ACK# C18 A[0] D24 WP AB4 MCS16# / PDDIR# A17 A[1] A18 BVD1 AB3 IOCS16# / INIT# D17 A[2] C26 BVD2 AD2 REF# / AUTPFDX# B16 A[3] A21 READY# AC3 AEN / SLCTIN# C17 A[4] C19 WAIT# E25 IOCHCK# / PPD[7] A16 A[5] A25 INPACK# E26 PPD[6] B15 A[6] C22 OE# F24 RTCRW# / PPD[5] A15 A[7] B18 WE# D25 RTCDS# / PPD[4] C16 A[8] B19 REG# E23 RTCAS# / PPD[3] B14 A[9] B24 CD1# D26 RMRTCCS# / PPD[2] D15 A[10] A24 CD2# E24 ALE / PPD[1] A14 A[11] B23 CE1# C25 PPD[0] C15 A[12] C23 CE2# AC1 STROBE# B13 A[13] C20 VS1# D13 A[14] A19 VS2# D5 IRQ_MUX[0] A13 A[15] D20 VCC5_EN A4 IRQ_MUX[1] C14 A[16] C21 VCC3_EN 32/55 Issue 1.1 PIN DESCRIPTION Pin # Pin name Pin # Pin name Pin # Pin name B21 VPP_PGM A8 RESERVED N4 VSS A22 VPP_VCC A23 RESERVED N11:16 VSS B5 RESERVED P11:16 VSS AD4 RED B17 RESERVED P23 VSS AF4 GREEN C12 RESERVED R11:16 VSS AE5 BLUE T11:16 VSS AF3 VSYNC D6 VDD V4 VSS AE4 HSYNC D11 VDD W23 VSS AF5 VREF_DAC D16 VDD AC4 VSS AE6 RSET D21 VDD AC8 VSS AF6 COMP F4 VDD AC13 VSS AE3 SDA / DDC[1] F23 VDD AC18 VSS AF2 SCL / DDC[0] L4 VDD AC23 VSS L23 VDD AD3 VSS AE7 B[2] T4 VDD AD24 VSS AF7 G[2] T23 VDD AE1 VSS AD7 R[2] AA4 VDD AE2 VSS AE8 B[3] AA23 VDD AE25 VSS AC9 G[3] AC6 VDD AF1 VSS AF8 R[3] AC11 VDD AF25 VSS AD8 B[4] AC16 VDD AF26 VSS AE9 G[4] AC21 VDD AF9 R[4] AE10 B[5] AC7 VSS_DAC1 AD9 G[5] AD6 VSS_DAC2 AF10 R[5] G26 VSS_DLL AC10 RESERVED H24 VSS_DLL AD10 FPLINE A1 VSS AE11 FPFRAME A2 VSS AF11 DE A26 VSS AE12 ENAVDD B2 VSS AF12 ENVCC B25 VSS AD11 PWM B26 VSS C3 VSS C24 VSS D4 VSS C8 SCAN_ENABLE AD5 VDD_DAC1 D9 VSS AC5 VDD_DAC2 D14 VSS AE17 VDD_GCLK_PLL D19 VSS AF17 VDD_DCLK_PLL D23 VSS K24 VDD_ZCLK_PLL H4 VSS H25 VDD_DEVCLK_PLL J23 VSS J24 VDD_HCLK_PLL L11:16 VSS M11:16 VSS 33/55 Issue 1.1 ELECTRICAL SPECIFICATIONS 4 ELECTRICAL SPECIFICATIONS 4.1 INTRODUCTION The electrical specifications in this chapter are valid for the STPC Industrial. 4.2 ELECTRICAL CONNECTIONS 4.2.1 Power/Ground Connections/Decoupling Due to the high frequency of operation of the STPC Industrial, it is necessary to install and test this device using standard high frequency techniques. The high clock frequencies used in the STPC Industrial and its output buffer circuits can cause transient power surges when several output buffers switch output levels simultaneously. These effects can be minimized by filtering the DC power leads with low-inductance decoupling capacitors, using low impedance wiring, and by utilizing all of the VSS and VDD pins. 4.2.2 Unused Input Pins in the table of pin connections in Section 3 should be connected either to VDD or to VSS. Connect active-high inputs to VDD through a 20 kΩ (±10%) pull-down resistor and active-low inputs to VSS and connect active-low inputs to VCC through a 20 kΩ (±10%) pull-up resistor to prevent spurious operation. 4.2.3 Reserved Designated Pins Pins designated reserved should be left disconnected. Connecting a reserved pin to a pull-up resistor, pull-down resistor, or an active signal could cause unexpected results and possible circuit malfunctions. All inputs not used by the designer and not listed 4.3 ABSOLUTE MAXIMUM RATINGS The following table lists the absolute maximum ratings for the STPC Industrial device. Stresses beyond those listed under Table 4-1 limits may cause permanent damage to the device. These are stress ratings only and do not imply that operation under any conditions other than those specified in section ”Operating Conditions”. Exposure to conditions beyond those outlined in Table 4-1 may (1) reduce device reliability and (2) result in premature failure even when there is no immediately apparent sign of failure. Prolonged exposure to conditions at or near the absolute maximum ratings (Table 4-1) may also result in reduced useful life and reliability. 4.3.1 5V Tolerance The STPC is capable of running with I/O systems that operate at 5V such as PCI and ISA devices. Certain pins of the STPC tolerate inputs up to 5.5V. Above this limit thecomponent is likely to sustain permanent damage. All the pin that are V5T have been denoted with a * besides the Signal Name in Table 3-1 . Table 4-1. Absolute Maximum Ratings Symbol VDDx VI , VO V5T TSTG TOPER PTOT Parameter DC Supply Voltage Digital Input and Output Voltage 5Volt Tolerance Storage Temperature Operating Temperature Maximum Power Dissipation Minimum -0.3 -0.3 2.5 -40 0 - 34/55 Issue 1.1 Maximum 4.0 VDD + 0.3 5.5 +150 +70 4.8 Units V V °C °C W ELECTRICAL SPECIFICATIONS 4.4 DC CHARACTERISTICS Table 4-2. DC Characteristics Recommended Operating conditions : VDD = 3.3V ± 0.3V, Tcase = 0 to 100°C unless otherwise specified Symbol VDD PDD H CLK V DAC VOL VOH V ILD Parameter Operating Voltage Supply Power Internal Clock DAC Voltage Reference Output Low Voltage Output High Voltage Input Low Voltage VIHD Input High Voltage ILK C IN C OUT C CLK Input Leakage Current Input Capacitance Output Capacitance Clock Capacitance Test conditions Min 3.0 Typ 3.3 3.2 1.215 1.235 VDD = 3.3V, HCLK = 66Mhz (Note 1) ILoad =1.5 to 8mA depending of the pin ILoad =-0.5 to -8mA depending of the pin Except XTALI XTALI Except XTALI XTALI Input, I/O (Note 2) (Note 2) (Note 2) 2.4 -0.3 -0.3 2.1 2.35 -5 Max 3.6 3.9 80 1.255 0.5 0.8 0.5 VDD+0.3 VDD+0.3 5 Unit V W Mhz V V V V V V V µA pF pF pF Notes: 1. MHz ratings refer to CPU clock frequency. 2. Not yet released. Table 4-3. RAMDAC DC Specification Symbol Vref INL DNL FS FSR LSB Zero Compare Parameter Voltage Reference Integrated Non Linear Error Differentiated Non Linear Error Full Scale Full Scale Range Least Significant Byte Size Zero Scale @ 7.5IRE Mode DAC to DAC matching Min 1.00V 14.00 mA 54uA 0.95mA - Nom 1.12V 16.50mA 63uA 1.44mA - Max 1.24V 2 lsb 1lsb 20mA 19.00 mA 72uA 1.90mA +/- 5% 4.5 AC CHARACTERISTICS Table 4-5 through Table 4-14 list the AC characteristics including output delays, input setup requirements, input hold requirements and output float delays. These measurements are based on the measurement points identified in Figure 4-1. The rising clock edge reference level VREF , and other reference levels are shown in Table 4-4 below for the STPC Industrial. Input or output signals must cross these levels during testing. Figure 4-1 shows output delay (A and B) and input setup and hold times (C and D). Input setup and hold times (C and D) are specified minimums, defining the smallest acceptable sampling window a synchronous input signal must be stable for correct operation. 35/55 Issue 1.1 ELECTRICAL SPECIFICATIONS Table 4-4. Drive Level and Measurement Points for Switching Characteristics Symbol VREF VIHD V ILD Value 1.5 3.0 0.0 Units V V V Note: Refer to Figure 4-1. Figure 4-1. Drive Level and Measurement Points for Switching Characteristics Tx VIHD VRef CLK: VILD A B MAX MIN Valid Output n OUTPUTS: Valid Output n+1 VRef C D VIHD Valid INPUTS: Input VRef VILD LEGEND: A B C D - Maximum Output Delay Specification - Minimum Output Delay Specification - Minimum Input Setup Specification - Minimum Input Hold Specification 36/55 Issue 1.1 ELECTRICAL SPECIFICATIONS Table 4-5. DRAM Bus AC Timing Name t1 t2 t3 t4 t5 t6 t7 t8 t9 t10 t11 t12 Parameter HCLK to RAS#[3:0] valid HCLK to CAS#[7:0] bus valid HCLK to MA[11:0] bus valid HCLK to MWE# valid Min HCLK to MD[63:0] bus valid MD[63:0] Generic setup GCLK2X to RAS#[3:0] valid GCLK2X to CAS#[7:0] valid GCLK2X to MA[11:0] bus valid GCLK2X to MWE# valid GCLK2X to MD[63:0] bus valid MD[63:0] Generic hold Max 16 16 16 16 Unit ns ns ns ns 16 ns ns ns ns ns ns ns ns 9 17 17 17 17 17 5 Table 4-6. PCI Interface AC TImings Name t13 t14 t15 t16 t17 Parameter PCI_CLKI to PCI_CLKI to PCI_CLKI to PCI_CLKI to PCI_CLKI to Min Max 15 15 15 15 15 Unit nS nS nS nS nS Min Max 27 27 Unit ns ns Min Max 71 68 - Unit nS nS nS nS FRAME# valid TRDY# valid IRDY# valid STOP# valid DEVSEL# valid Table 4-7. Graphics Adapter (VGA) AC Timing Name t18 t19 Parameter DCLK to VSYNC valid DCLK to HSYNC valid Table 4-8. IPC Interface AC Timings Name t20 t21 t22 t23 Parameter XTALO to DACK_EN[2:0] valid XTALO to TC valid IRQ_MUX Input setup to ISACLK2X DREQ_MUX[1:0] Input setup to ISACLK2X 0 0 37/55 Issue 1.1 ELECTRICAL SPECIFICATIONS Table 4-9. PCMCIA Interface AC Timing Name t24 t25 t28 t29 t30 t31 t32 t33 t34 t35 t36 t37 Parameters Input setup to ISACLK2X Input hold from ISACLK2X ISACLK2X to IORD ISACLK2X to IORW ISACLK2X to AD[25:0] ISACLK2X to OE# ISACLK2X to WE# ISACLK2X to DATA[15:0] ISACLK2X to INPACK ISACLK2X to CE1# ISACLK2X to CE2# ISACLK2X to RESET Min 24 5 2 2 0 2 7 7 2 Max 55 55 25 55 55 35 55 65 65 55 Units nS nS nS nS nS nS nS nS nS nS nS nS Min 0 0 0 Max - Units nS nS nS Min 5 1 - Max 12 Units nS nS nS Min 5 1 - Max 12 Units nS nS nS Table 4-10. Parallel Interface AC Timing Name t37 t38 t39 Parameters STROBE# to BUSY setup PD bus to AUTPFD# hold PB bus to BUSY setup Table 4-11. Keyboard Interface AC Timing Name t40 t41 t42 Parameters Input setup to KBCLK Input hold to KBCLK KBCLK to KBDATA Table 4-12. Mouse Interface AC Timing Name t43 t44 t45 Parameters Input setup to MCLK Input hold to MCLK MCLK to MDATA 38/55 Issue 1.1 ELECTRICAL SPECIFICATIONS Table 4-13. Local Bus Interface AC Timing Name t46 t47 t48 t49 t50 t51 t52 t53 t54 t55 t56 t57 t58 Parameters PRDY# Input hold to HCLK PD[15:0] Input hold to HCLK PRDY# Input setup to HCLK PD[15:0] Input setup to HCLK HCLK to PA bus HCLK to PD bus HCLK to PWR0# HCLK to PWR1# HCLK to PRD0# HCLK to PRD1# HCLK to FCS0# HCLK to FCS1# HCLK to IOCS#[3:0] Min 2 2 1 2 - Max 4 15 15 15 15 15 15 15 15 15 Units nS nS nS nS nS nS nS nS nS nS nS nS nS Min Max 15 15 15 15 15 15 15 15 15 15 15 15 15 15 Units nS nS nS nS nS nS nS nS nS nS nS nS nS nS Table 4-14. TFT Interface Timing Name t59 t60 t61 t62 t63 t64 t65 t66 t67 t68 t68 t69 t70 t71 Parameters DCLK to FPLINE DCLK to R[2] DCLK to R[3] DCLK to R[4] DCLK to R[5] DCLK to G[2] DCLK to G[3] DCLK to G[4] DCLK to G[5] DCLK to B[2] DCLK to B[3] DCLK to B[4] DCLK to B[5] DCLK to FPFRAME 39/55 Issue 1.1 ELECTRICAL SPECIFICATIONS 40/55 Issue 1.1 MECHANICAL DATA 5. MECHANICAL DATA 5.1 388-PIN PACKAGE DIMENSION The pin numbering for the STPC 388-pin Plastic BGA package is shown in Figure 5-1. Dimensions are shown in Figure 5-2, Table 5-1 and Figure 5-3, Table 5-2. Figure 5-1. 388-Pin PBGA Package - Top View 1 3 2 5 4 7 6 9 8 11 10 13 12 15 14 17 16 19 18 21 20 23 22 25 24 26 A A B C B C D D E F E F G G H H J J K K L L M N M N P P R R T T U U V V W W Y Y AA AA AB AC AB AC AD AD AE AE AF AF 1 3 2 5 4 7 6 9 8 11 10 13 12 15 14 17 16 19 18 21 20 23 22 25 24 26 41/55 Issue 1.1 MECHANICAL DATA Figure 5-2. 388-pin PBGA Package - PCB Dimensions A1 Ball Pad Corner A B A D E F Detail C G Table 5-1. 388-pin PBGA Package - PCB Dimensions Symbols A B C D E F G Min 34.95 1.22 0.58 1.57 0.15 0.05 0.75 mm Typ 35.00 1.27 0.63 1.62 0.20 0.10 0.80 Max 35.05 1.32 0.68 1.67 0.25 0.15 0.85 42/55 Issue 1.1 Min 1.375 0.048 0.023 0.062 0.006 0.002 0.030 inches Typ 1.378 0.050 0.025 0.064 0.008 0.004 0.032 Max 1.380 0.052 0.027 0.066 0.001 0.006 0.034 MECHANICAL DATA Figure 5-3. 388-pin PBGA Package - Dimensions C F D E Solderball Solderball after collapse B G A Table 5-2. 388-pin PBGA Package - Dimensions Symbols A B C D E F G Min 0.50 1.12 0.60 0.52 0.63 0.60 mm Typ 0.56 1.17 0.76 0.53 0.78 0.63 30.0 Max 0.62 1.22 0.92 0.54 0.93 0.66 Min 0.020 0.044 0.024 0.020 0.025 0.024 inches Typ 0.022 0.046 0.030 0.021 0.031 0.025 11.8 Max 0.024 0.048 0.036 0.022 0.037 0.026 43/55 Issue 1.1 MECHANICAL DATA 5.2 388-PIN PACKAGE THERMAL DATA 388-pin PBGA package has a Power Dissipation Capability of 4.5W which increases to 6W when used with a Heatsink. Structure in shown in Figure 5-4. Thermal dissipation options are illustrated in Figure 5-5 and Figure 5-6. Figure 5-4. 388-Pin PBGA structure Signal layers Power & Ground layers Thermal balls Figure 5-5. Thermal dissipation without heatsink Board Ambient Board dimensions: - 10.2 cm x 12.7 cm - 4 layers (2 for signals, 1 GND, 1VCC) Junction Rca Case 6 Rjc Junction 6 Board Case 8.5 125 Rjb Board Rba Ambient Ambient Rja = 13 °C/W 44/55 Issue 1.1 The PBGA is centered on board There are no other devices 1 via pad per ground ball (8-mil wire) 40% copper on signal layers Copper thickness: - 17µm for internal layers - 34µm for external layers Airflow = 0 Board temperature taken at the center balls MECHANICAL DATA Figure 5-6. Thermal dissipation with heatsink Board Ambient Board dimensions: - 10.2 cm x 12.7 cm - 4 layers (2 for signals, 1 GND, 1VCC) Junction Rca Case 3 Rjc Junction 6 Board Case 8.5 50 Rjb Board Rba The PBGA is centered on board There are no other devices 1 via pad per ground ball (8-mil wire) 40% copper on signal layers Copper thickness: - 17µm for internal layers - 34µm for external layers Ambient Ambient Rja = 9.5 °C/W Airflow = 0 Board temperature taken at the center balls Heat sink is 11.1°C/W 45/55 Issue 1.1 MECHANICAL DATA 46/55 Issue 1.1 BOARD LAYOUT 6. BOARD LAYOUT 6.1 THERMAL DISSIPATION Thermal dissipation of the STPC depends mainly on supply voltage. As a result, when the system does not need to work at 3.3V, it may be to reduce the voltage to 3.15V for example. This may save few 100’s of mW. The second area that can be concidered is unused interfaces and functions. Depending on the application, some input signals can be grounded, and some blocks not powered or shutdown. Clock speed dynamic adjustment is also a solution that can be used along with the integrated power management unit. The standard way to route thermal balls to internal ground layer implements only one via pad for each ball pad, connected using a 8-mil wire. With such configuration the Plastic BGA 388 package dissipates 90% of the heat through the ground balls, and especially the central thermal balls which are directly connected to the die, the remaining 10% is dissipated through the case. Adding a heat sink reduces this value to 85%. As a result, some basic rules have to be applied when routing the STPC in order to avoid thermal problems. First of all, the whole ground layer acts as a heat sink and ground balls must be directly connected to it as illustrated in Figure 6-1. If one ground layer is not enough, a second ground plane may be added on the solder side. Figure 6-1. Ground routing Pad for ground ball Thru hole to ground layer Top L ayer : Sign Grou als nd la yer Powe r laye r Botto mLa yer : signa ls + lo cal g round layer (if ne eded ) Note: For better visibility, ground balls are not all routed. 47/55 Issue 1.1 BOARD LAYOUT When considering thermal dissipation, the most important - and not the more obvious - part of the layout is the connection between the ground balls and the ground layer. A 1-wire connection is shown in Figure 6-2. The use of a 8-mil wire results in a thermal resistance of 105°C/W assuming copper is used (418 W/ m.°K). This high value is due to the thickness (34 µm) of the copper on the external side of the PCB. Considering only the central matrix of 36 thermal balls and one via for each ball, the global thermal resistance is 2.9°C/W. This can be easily improved by using four 10 mil wires to connect to the four vias around the ground pad link as in Figure 6-3. This gives a total of 49 vias and a global resistance for the 36 thermal balls of 0.6°C/W. The use of a ground plane like in Figure 6-4 is even better. To avoid solder wicking over to the via pads during soldering, it is important to have a solder mask of 4 mil around the pad (NSMD pad), this gives a diameter of 33 mil for a 25 mil ground pad. To obtain the optimum ground layout, place the vias directly under the ball pads. In this case no local boar d distortion is tolerated. The thickness of the copper on PCB layers is typically 34 µm for external layers and 17 µm for internal layers. This means thermal dissipation is not good and temperature of the board is concentrated around the devices and falls quickly with increased distance. When it is possible to place a metal layer inside the PCB, this improves dramatically the heat spreading and hence thermal dissipation of the board. Figure 6-2. Recommended 1-wire ground pad layout Pad for ground ball (diameter = 25 mil) Solder Mask (4 mil) Connection Wire (width = 10 mil) .5 34 Via (diameter = 24 mil) il m Hole to ground layer (diameter = 12 mil) 1 mil = 0.0254 mm Figure 6-3. Recommended 4-wire ground pad layout 4 via pads for each ground ball 48/55 Issue 1.1 BOARD LAYOUT Figure 6-4. Optimum layout for central ground ball Clearance = 6mil External diameter = 37 mil Via to Ground layer hole diameter = 14 mil Solder mask diameter = 33 mil Pad for ground ball diameter = 25 mil connections = 10 mil The PBGA Package also dissipates heat through peripheral ground balls. When a heat sink is placed on the device, heat is more uniformely spread throughout the moulding increasing heat dissipation through the peripheral ground balls. The more via pads are connected to each ground ball, the more heat is dissipated . The only limitation is the risk of lossing routing channels. Figure 6-5 shows a routing with a good trade off between thermal dissipation and number of routing channels. Figure 6-5. Global ground layout for good thermal dissipation Via to ground layer Ground pad 49/55 Issue 1.1 BOARD LAYOUT Figure 6-6. Bottom side layout and decoupling Ground plane for thermal dissipation Via to ground layer A local ground plane on opposite side of the board as shown in Figure 6-6 improves thermal dissipation. It is used to connect decoupling capacitances but can also be used for connection to a heat sink or to the system’s metal box for better dissipation. This possibility of using the whole system’s box for thermal dissipation is very usefull in case of high temperature inside the system and low temperature outside. In that case, both sides of the PBGA should be thermally connected to the metal chassis in order to propagate the heat through the metal. Figure 6-7 illustrates such an implementation. Figure 6-7. Use of metal plate for thermal dissipation Die Board Metal planes Thermal conductor 50/55 Issue 1.1 BOARD LAYOUT 6.2 HIGH SPEED SIGNALS Some Interfaces of the STPC run at high speed and have to be carefully routed or even shielded. Here is the list of these interfaces, in decreasing speed order: - Memory Interface. - Graphics and video interfaces - PCI bus - 14MHz oscillator stage All the clocks have to be routed first and shielded for speeds of 27MHz or more. The high speed signals have the same contrainsts as some of the memory interface control signals. The next interfaces to be routed are Memory, Video/graphics, and PCI. All the analog noise sensitive signals have to be routed in a separate area and hence can be routed indepedently. Figure 6-8. Shielding signals ground ring shielded signal line ground pad ground pad shielded signal lines 51/55 Issue 1.1 BOARD LAYOUT 52/55 Issue 1.1 ORDERING DATA 7 ORDERING DATA 7.1 ORDERING CODES ST PC I01 66 BT C 3 STMicroelectronics Prefix Product Family PC: PC Compatible Product ID I01: Industrial Core Speed 66: 66MHz 80: 80MHz Package BT: 388 Overmoulded BGA Temperature Range C: Commercial Tcase = 0 to +100°C I: Industrial Tcase = -40 to +100°C Operating Voltage 3 : 3.3V ± 0.3V 53/55 Issue 1.1 ORDERING DATA 7.2 AVAILABLE PART NUMBERS Part Number STPCI0166BTC3 STPCI0180BTC3 STPCI0166BTI3 STPCI0180BTI3 Core Frequency (MHz) 66 80 66 80 CPU Mode DX DX DX DX 54/55 Issue 1.1 Tcase Range (C) Operating Voltage (V) 0°C to +100°C 3.3V ± 0.3V -40°C to +100°C Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express writt en approval of STMicroelectronics. 1999 STMicroelectronics - All Rights Reserved The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. STMicroelectronics GROUP OF COMPANIES Australia - Brazil - China - France - Germany - Italy - Japan - Korea - Malaysia - Malta - Mexico - Morocco - The Netherlands - Singapore Spain - Sweden - Switzerland - Taiwan - Thailand - United Kingdom - U.S.A. 55 Issue 1.1