STPC CONSUMER-S PC Compatible Embeded Microprocessor ADVANCED DATA ■ POWERFUL x86 PROCESSOR ■ 64-BIT 66MHz SDRAM UMA CONTROLLER ■ VGA & SVGA CRT CONTROLLER ■ 2D GRAPHICS ENGINE ■ VIDEO INPUT PORT ■ VIDEO PIPELINE - UP-SCALER - VIDEO COLOR SPACE CONVERTER - CHROMA & COLOUR KEY SUPPORT ■ TV OUTPUT - 3-LINE FLICKER FILTER - CCIR 601/656 SCAN CONVERTER - NTSC / PAL COMPOSITE, RGB, S-VIDEO ■ PCI MASTER / SLAVE CONTROLLER ■ ISA MASTER / SLAVE CONTROLLER ■ INTEGRATED PERIPHERAL CONTROLLER - DMA CONTROLLER - INTERRUPT CONTROLLER - TIMER / COUNTERS ■ OPTIONAL 16-BIT LOCAL BUS INTERFACE ■ EIDE CONTROLLER ■ I C INTERFACE ■ POWER MANAGEMENT UNIT ■ 3.3V OPERATION STPC CONSUMER-S OVERVIEW The STPC Consumer-S integrates a standard 5th generation x86 core, a Synchronous DRAM controller, a graphics subsystem, a video input port, video pipeline, and support logic including PCI, ISA, and IDE controllers to provide a single consumer orientated PC compatible subsystem on a single device. The device is based on a tightly coupled Unified Memory Architecture (UMA), sharing the same memory array between the CPU main memory and the graphics and video frame buffers. The STPC Consumer-S is packaged in a 388 Plastic Ball Grid Array (PBGA). PBGA388 Figure 1. Logic Diagram Host I/F x86 Core PCI m/s PCI Bus PMU W.dog IPC ISA m/s PCI m/s IDE I/F ISA Bus LB CTR Video Pipeline SVGA CRTC Local Bus C Key K Key LUT Monitor TVO Cursor GE Encoder TV VIP SDRAM CTRL 29/10/99 Release B This is preliminary information on a new product now in development or undergoing evaluation. Details are subject to change without notice. 1/51 STPC CONSUMER-S ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ X86 Processor core Fully static 32-bit 5-stage pipeline, x86 processor fully PC compatible. Can access up to 4GB of external memory. 8Kbyte unified instruction and data cache with write back and write through capability. Parallel processing integral floating point unit, with automatic power down. Fully static design for dynamic clock control. Low power and system management modes. ■ SDRAM Controller 64-bit data bus. Up to 66MHz SDRAM clock speed. Integrated system memory, graphic frame memory and video frame memory. Supports 2MB up to 128 MB memory. Supports 8MB, 16M, and 32MB DIMMs. Supports buffered, non buffered, and registered DIMMs 4-line write buffers for CPU to DRAM and PCI to DRAM cycles. 4-line read prefetch buffers for PCI masters. Programmable latency Programmable timing for DRAM parameters. Supports -8, -10, -12, -13, -15 memory parts Supports 1MB up to 8MB memory hole. 32-bit accesses not supported. Autoprecharge not supported. Power down not supported. FPM and EDO not supported. ■ Graphics Controller 64-bit windows accelerator. Compatibility to VGA & SVGA standards. Hardware acceleration for text, bitblts, transparent blts and fills. Up to 64 x 64 bit graphics hardware cursor. Up to 4MB long linear frame buffer. 8-, 16-, and 24-bit pixels. ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ CRT Controller Integrated 135MHz triple RAMDAC allowing for 1024 x 768 x 75Hz display. 8-, 16-, 24-bit pixels. Interlaced or non-interlaced output. Video Input port Accepts video inputs in CCIR 601 mode. Optional 2:1 decimator Stores captured video in off setting area of the onboard frame buffer. Video pass through to the onchip PAL/NTSC encoder for full screen video images. HSYNC and B/T generation or lock onto external video timing source. Video Pipeline Two-tap interpolative horizontal filter. Two-tap interpolative vertical filter. Color space conversion. Programmable window size. Chroma and color keying for integrated video overlay. TV Output Programmable two tap filter with gamma correction or three tap flicker filter. Progressive to interlaced scan converter. NTSC-M, PAL-M,PAL-B,D,G,H,I,PAL-N easy programmable video outputs. CCIR601 encoding with programmable color subcarrier frequencies. Line skip/insert capability Interlaced or non-interlaced operation mode. 625 lines/50Hz or 525 lines/60Hz 8 bit multiplexed CB-Y-CR digital input. CVBS and R,G,B simultaneous analog outputs through 10-bit DACs. Cross color reduction by specific trap filtering on luma within CVBS flow. Power down mode available on each DAC. 2/51 Release B This is preliminary information on a new product now in development or undergoing evaluation. Details are subject to change without notice. STPC CONSUMER-S ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ PCI Controller Fully compliant with PCI 2.1 specification. Integrated PCI arbitration interface. Up to 3 masters can connect directly. External PAL allows for greater than 3 masters. Translation of PCI cycles to ISA bus. Translation of ISA master initiated cycle to PCI. Support for burst read/write from PCI master. PCI clock is 1/3 or 1/2 Host clock . ■ ISA master/slave controller Generates the ISA clock from either 14.318MHz oscillator clock or PCI clock Supports programmable extra wait state for ISA cycles Supports I/O recovery time for back to back I/ O cycles. Fast Gate A20 and Fast reset. Supports the single ROM that C, D, or E. blocks shares with F block BIOS ROM. Supports flash ROM. Supports ISA hidden refresh. Buffered DMA & ISA master cycles to reduce bandwidth utilization of the PCI and Host bus. NSP compliant. ■ Integrated Peripheral Controller 2X8237/AT compatible 7-channel DMA controller. 2X8259/AT compatible interrupt Controller. 16 interrupt inputs - ISA and PCI. Three 8254 compatible Timer/Counters. Co-processor error support logic. Supports external RTC. ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ IDE Interface Supports PIO and Bus Master IDE Supports up to Mode 5 Timings Transfer Rates to 22 MBytes/sec Supports up to 4 IDE devices Concurrent channel operation (PIO & DMA modes) - 4 x 32-Bit Buffer FIFO per channel Support for PIO mode 3 & 4. Support for DMA mode 1 & 2. Support for 11.1/16.6 MB/s, I/O Channel Ready PIO data transfers. Supports 13.3/16.6 MB/s DMA data transfers Bus Master with scatter/gather capability Multi-word DMA support for fast IDE drives Individual drive timing for all four IDE devices Supports both legacy & native IDE modes Supports hard drives larger than 528MB Support for CD-ROM and tape peripherals Backward compatibility with IDE (ATA-1). Power Management Four power saving modes: On, Doze, Standby, Suspend. Programmable system activity detector Supports SMM. Supports STOPCLK. Supports IO trap & restart. Independent peripheral time-out timer to monitor hard disk, serial & parallel ports. Supports RTC, interrupts and DMAs wake-up Local Bus interface Multiplxed with ISA interface. Low latency bus 22-bit address bus. 16-bit data bus with word steering capability. Programmable timing (Host clock granularity) 2 Programmable Flash Chip Select. 5 Programmable I/O Chip Select. Supports 32-bit Flash burst. 2-level hardware key protection for Flash boot block protection. Supports 2 banks of 8MB flash devices with boot block shadowed to 0x000F0000. 3/51 Release B This is preliminary information on a new product now in development or undergoing evaluation. Details are subject to change without notice. GENERAL DESCRIPTION 1 GENERAL DESCRIPTION At the heart of the STPC Consumer-S is an advanced 64-bit processor block, dubbed the 5ST86. The 5ST86 includes a 486 processor core along with a 64-bit SDRAM controller, advanced 64-bit accelerated graphics and video controller, a high speed PCI local-bus controller and Industry standard PC chip set functions (Interrupt controller, DMA Controller, Interval timer and ISA bus). The STPC Consumer-S makes use of a tightly coupled Unified Memory Architecture (UMA), where the same memory array is used for CPU main memory and graphics frame-buffer. This means a reduction in total system memory for system performances that are equal to that of a comparable frame buffer and system memory based system, and generally much better, due to the higher memory bandwidth allowed by attaching the graphics engine directly to the 64-bit processor host interface running at the speed of the processor bus rather than the traditional PCI bus. The 64-bit wide memory array provides the system with 528MB/s peak bandwidth. This allows for higher resolution screens and greater color depth. The ‘standard’ PC chipset functions (DMA, interrupt controller, timers, power management logic) are integrated together with the x86 processor core; additional functions such as communications ports are accessed by the STPC ConsumerS via internal ISA bus. The PCI bus is the main data communication link to the STPC Consumer-S chip. The STPC Consumer-S translates appropriate host bus I/O and Memory cycles onto the PCI bus. It also supports generation of Configuration cycles on the PCI bus. The STPC Consumer-S, as a PCI bus agent (host bridge class), fully complies with PCI specification 2.1. The chip-set also implements the PCI mandatory header registers in Type 0 PCI configuration space for easy porting of PCI aware system BIOS. The device contains a PCI arbitration function for three external PCI devices. The STPC Consumer-S has two functionnal blocks sharing the same balls : The ISA / IPC / IDE block and the Local Bus / IDE block (see Table 3). Any board with the STPC Consumer-S should be built using only one of these two configurations. At reset, the configuration is done by ‘strap options’ which initialises the STPC Consumer-S to the right settings. It is a set of pull-up or pull-down resistors on the memory data bus, checked on reset, which auto-configure the STPC Consumer-S. GRAPHICS FUNCTIONS Graphics functions are controlled through the onchip SVGA controller and the monitor display is produced through the 2D graphics display engine. This Graphics Engine is tuned to work with the host CPU to provide a balanced graphics system with a low silicon area cost. It performs limited graphics drawing operations which include hardware acceleration of text, bitblts, transparent blts and fills. The results of these operations change the contents of the on-screen or off-screen frame buffer areas of DRAM memory. The frame buffer can occupy a space up to 4 Mbytes anywhere in the physical main memory and always starts from the bottom of the main physical memory. The graphics resolution supported is a maximum of 1280x1024 in 65536 colours and 1024x768 in true color at 75Hz refresh rate and is VGA and SVGA compatible. Horizontal timing fields are VGA compatible while the vertical fields are extended by one bit to accommodate above display resolution. VIDEO FUNCTIONS The STPC Consumer-S provides several additional functions to handle MPEG or similar video streams. The Video Input Port accepts an encoded digital video stream in one of a number of industry standard formats, decodes it, optionally decimates it, and deposits it into an off screen area of the frame buffer. An interrupt request can be generated when an entire field or frame has been captured. The video output pipeline incorporates a video-scaler and color space converter function and provisions in the CRT controller to display a video window. While repainting the screen the CRT controller fetches both the video as well as the normal non-video frame buffer in two separate internal FIFOs. The video stream can be color-space converted (optionally) and smooth scaled. Smooth interpolative scaling in both horizontal and vertical direction are implemented. Color and Chroma key functions are also implemented to allow mixing video stream with non-video frame buffer. The video output passes directly to the RAMDAC for monitor output or through another optional color space converter (RGB to 4:2:2 YCrCb) to the programmable anti-flicker filter. The flicker filter is configured as either a two line filter with gamma correction (primarily designed for DOS type text) or a 3 line flicker filter (primarily designed for Windows type displays). The fliker filter is optional and can be software disabled for use with large screen area’s of video. 4/51 Release B This is preliminary information on a new product now in development or undergoing evaluation. Details are subject to change without notice. GENERAL DESCRIPTION The Video output pipeline of the STPC ConsumerS interfaces directly to the internal digital TV encoder. It takes a 24 bit RGB non-interlaced pixel stream and converts to a multiplexed 4:2:2 YCrCb 8 bit output stream, the logic includes a progressive to interlaced scan converter and logic to insert appropriate CCIR656 timing reference codes into the output stream. It facilitates the high quality display of VGA or full screen video streams received via the Video input port to standard NTSC or PAL televisions. The digital PAL/NTSC encoder outputs interlaced or non-interlaced video in PAL-B,D,G,H,I PAL-N, PAL-M or NTSC-M standards and “NTSC- 4.43” is also possible. The four frame (for PAL) or 2 frame (for NTSC) burst sequences are internally generated, subcarrier generation being performed numerically with CKREF as reference. Rise and fall times of synchronisation tips and burst envelope are internally controlled according to the relevant ITU-R and SMPTE recommendations. Video output signals are directed to four analog output pins through internal D/A converters giving, simultaneous R,G,B and composite CVBS outputs. IDE INTERFACE An industry standard EIDE (ATA 2) controller is built into the STPC Consumer-S. The IDE port is capable of supporting a total of four devices. POWER MANAGEMENT - House-keeping timer to cope with short bursts of house-keeping activity while dozing or in stand-by state. - Peripheral activity detection. - Peripheral timer for detecting lack of peripheral activity - SUSP# modulation to adjust the system performance in various power down states of the system including full power on state. - Power control outputs to disable power from different planes of the board. Lack of system activity for progressively longer period of times is detected by the three power down timers. These timers can generate SMI interrupts to CPU so that the SMM software can put the system in decreasing states of power consumption. Alternatively, system activity in a power down state can generate SMI interrupt to allow the software to bring the system back up to full power on state. The chip-set supports up to three power down states: Doze state, Stand-by state and Suspend mode. These correspond to decreasing levels of power savings. POWER DOWN Power down puts the STPC Consumer-S into suspend mode. The processor completes execution of the current instruction, any pending decoded instructions and associated bus cycles. During the suspend mode, internal clocks are stopped. Removing power down, the processor resumes instruction fetching and begins execution in the instruction stream at the point it had stopped. Because of the static nature of the core, no internal data is lost. The STPC Consumer-S core is compliant with the Advanced Power Management (APM) specification to provide a standard method by which the BIOS can control the power used by personal computers. The Power Management Unit module (PMU) controls the power consumption providing a comprehensive set of features that control the power usage and supports compliance with the United States Environmental Protection Agency’s Energy Star Computer Program. The PMU provides following hardware structures to assist the software in managing the power consumption by the system. - System Activity Detection. - Three power down timers. - Doze timer for detecting lack of system activity for short durations. - Stand-by timer for detecting lack of system activity for medium durations - Suspend timer for detecting lack of system activity for long durations. - House-keeping activity detection. 5/51 Release B This is preliminary information on a new product now in development or undergoing evaluation. Details are subject to change without notice. GENERAL DESCRIPTION Figure 2. Functionnal description. Host I/F x86 Core PCI BUS PCI m/s PMU watch- IPC 82C206 ISA m/s PCI m/s IDE I/F ISA Bus Local Bus I/F Local Bus Video Pipeline - Pixel formating - Scaler - Colour Space Colour Key Chroma Key LUT Monitor SVGA TVO CRTC - CSC - FF - CCIR HW Cursor GE VIP NTSC/PAL Encoder TV CCIR Input SDRAM I/F 6/51 Release B This is preliminary information on a new product now in development or undergoing evaluation. Details are subject to change without notice. GENERAL DESCRIPTION Figure 3. Typical Application Super I/O RTC Keyboard / Mouse Serial Ports Parallel Port Floppy Flash 2x EIDE ISA DMUX MUX Monitor IRQ SVGA MUX DMA.REQ STPC Consumer-S DMA.ACK TV S-VHS RGB PAL NTSC DMUX Video CCIR601 CCIR656 PCI 4x 16-bit SDRAMs 7/51 Release B This is preliminary information on a new product now in development or undergoing evaluation. Details are subject to change without notice. GENERAL DESCRIPTION 8/51 Release B This is preliminary information on a new product now in development or undergoing evaluation. Details are subject to change without notice. Update History for Video controller chapter 1.1 UPDATE HISTORY FOR VIDEO CONTROLLER CHAPTER The following changes have been made to the General Description Chapter on 29/10/99. Section 1 Change Removed Text “The STPC Consumer-S has in addition to the 5ST86 a TFT output, a Local Bus interface, a WatchDog and a JTAG interface.” 9/51 Release B PIN DESCRIPTION 2 PIN DESCRIPTION 2.1 INTRODUCTION The STPC Consumer-S integrates most of the functionalities of the PC architecture. As a result, many of the traditional interconnections between the host PC microprocessor and the peripheral devices are totally internal to the STPC Consumer-S. This offers improved performance due to the tight coupling of the processor core and these peripherals. As a result many of the external pin connections are made directly to the on-chip peripheral functions. Table 2.1. Signal Description Group name System Clocks & Resets Qty 11 Memory Interface PCI interface ISA IDE Local Bus Video Input TV Output VGA Monitor interface Grounds VDD Analog specific VCC/VDD Total Pin Count Figure 2.1 shows the STPC Consumer-S external interfaces. It defines the main busses and their function. Table 2.1 describes the physical implementation listing signals type and their functionality. Table 2.2 provides a full pin listing and description of pins. Table 2.5 provides a full listing of pin locations of the STPC Consumer-S package by physical connection. 95 60 79 34 49 89 11 8 8 71 29 6 388 Note: Several interface pins are multiplexed with other functions, refer to Table 2.3 and Table 2.4 for further details Figure 2.1. STPC Consumer-S External Interfaces STPC CONSUMER-S x86 PCI SDRAM VGA 95 8 VIP TV 11 8 60 SYS ISA/IDE/LB 11 89 10/51 Release B This is preliminary information on a new product now in development or undergoing evaluation. Details are subject to change without notice. PIN DESCRIPTION Table 2.2. Definition of Signal Pins Signal Name BASIC CLOCKS AND RESETS SYSRSTI# SYSRSTO# XTALI XTALO HCLK DEV_CLK DCLK Dir Description Qty I O I I/O I/O O I/O System Power Good Input System Reset Output 14.3MHz Crystal Input 14.3MHz Crystal Output - External Oscillator Input Host Clock (Test) 24MHz Peripheral Clock (floppy drive) 27-135MHz Graphics Dot Clock 1 1 1 1 1 1 1 MEMORY INTERFACE MCLKI MCLKO CS#[3:0] MA[11:0] MD[63:0] RAS#[1:0] CAS#[1:0] MWE# DQM[7:0] I O O O I/O O O O O Memory Clock Input Memory Clock Output DIMM Chip Select Memory Row & Column Address Memory Data Row Address Strobe Column Address Strobe Write Enable Data Input/Output Mask 1 1 4 12 64 2 2 1 8 PCI INTERFACE PCI_CLKI PCI_CLKO AD[31:0] CBE#[3:0] FRAME# IRDY# TRDY# LOCK# DEVSEL# STOP# PAR SERR# PCIREQ#[2:0] I O I/O I/O I/O I/O I/O I I/O I/O I/O O I 33MHz PCI Input Clock 33MHz PCI Output Clock (from internal PLL) PCI Address / Data Bus Commands / Byte Enables Cycle Frame Initiator Ready Target Ready PCI Lock Device Select Stop Transaction Parity Signal Transactions System Error PCI Request 1 1 32 4 1 1 1 1 1 1 1 1 3 PCI_GNT#[2:0] PCI_INT[3:0] VDD5 O I I PCI Grant PCI Interrupt Request 5V Power Supply for PCI ESD protection ISA CONTROL ISA_CLK ISA_CLK2X OSC14M LA[23:17] SA[19:0] SD[15:0] O O O O I/O I/O ISA Clock Output - Multiplexer Select Line For IPC ISA Clock x2 Output - Multiplexer Select Line For IPC ISA bus synchronisation clock Unlatched Address Latched Address Data Bus ALE MEMR#, MEMW# SMEMR#, SMEMW# O I/O O Address Latch Enable Memory Read and Memory Write System Memory Read and Memory Write 3 4 4 1 1 1 7 20 16 1 2 2 11/51 Release B This is preliminary information on a new product now in development or undergoing evaluation. Details are subject to change without notice. PIN DESCRIPTION Table 2.2. Definition of Signal Pins Signal Name IOR#, IOW# MCS16#, IOCS16# BHE# ZWS# REF# MASTER# AEN IOCHCK# IOCHRDY ISAOE# GPIOCS# IRQ_MUX[3:0] DREQ_MUX[1:0] DACK_ENC[2:0] TC RTCAS RMRTCCS# KBCS# RTCRW# RTCDS Dir I/O I O I O I O I I/O O I/O I I O O O I/O I/O I/O I/O Description I/O Read and Write Memory/IO Chip Select16 System Bus High Enable Zero Wait State Refresh Cycle. Add On Card Owns Bus Address Enable I/O Channel Check. I/O Channel Ready (ISA) - Busy/Ready (IDE) ISA/IDE Selection General Purpose Chip Select Time-Multiplexed Interrupt Request Time-Multiplexed DMA Request Encoded DMA Acknowledge ISA Terminal Count Real Time Clock Address Strobe ROM/RTC Chip Select Keyboard Chip Select RTC Read/Write RTC Data Strobe Qty 2 2 1 1 1 1 1 1 1 1 1 4 2 3 1 1 1 1 1 1 LOCAL BUS PA[21:0] PD[15:0] PRD1#,PRD0# PWR1#,PWR0# PRDY# FCS1#, FCS0# IOCS#[3:0] O I/O O O I O O Address Bus Data Bus Peripheral Read Control Peripheral Write Control Data Ready Flash Chip Select I/O Chip Select 22 16 2 2 1 2 4 IDE CONTROL DA[2:0] DD[15:0] PCS3#,PCS1#,SCS3#,SCS1# O I/O O Address Bus Data Bus Primary & Secondary Chip Selects 3 16 4 DIORDY PIRQ, SIRQ PDRQ, SDRQ PDACK#, SDACK# PDIOR#, SDIOR# PDIOW#, SDIOW# O I I O O O Data I/O Ready Primary & Secondary Primary & Secondary Primary & Secondary Primary & Secondary Primary & Secondary MONITOR INTERFACE RED, GREEN, BLUE VSYNC HSYNC O O O Analog Red, Green, Blue Vertical Sync Horizontal Sync 3 1 1 VREF_DAC RSET COMP I I I DAC Voltage reference Resistor Set Compensation 1 1 1 Interrupt Request DMA Request DMA Acknowledge I/O Channel Read I/O Channel Write 1 2 2 2 2 2 12/51 Release B This is preliminary information on a new product now in development or undergoing evaluation. Details are subject to change without notice. PIN DESCRIPTION Table 2.2. Definition of Signal Pins Signal Name VIDEO INPUT VCLK VIN VCS ODD_EVEN Dir Description Qty I I I/O I/O 27-33MHz Video Input Port Clock CCIR 601 or 656 YUV Video Data Input Composite Synch or Horizontal line SYNC output Frame Synchronisation 1 8 1 1 ANALOG TV OUTPUT RED_TV, GREEN_TV, BLUE_TV CVBS IREF1_TV VREF1_TV IREF2_TV VREF2_TV VSSA_TV VDDA_TV O O I I I I I I Analog RGB or S-VHS outputs Analog video composite output Reference current of 9bit DAC for CVBS Reference voltage of 9bit DAC for CVBS Reference current of 8bit DAC for R,G,B Reference voltage of 8bit DAC for R,G,B Analog Vss for DAC Analog Vdd for DAC 3 1 1 1 1 1 1 1 MISCELLANEOUS SPKRD SCL SDA SCAN_ENABLE O I/O I/O I Speaker Device Output I C Interface - Clock / Can be used for VGA DDC[1] signal I C Interface - Data / Can be used for VGA DDC[0] signal Reserved (Test pin) 1 1 1 1 2.2 SIGNAL DESCRIPTIONS 2.2.1 BASIC CLOCKS AND RESETS SYSRSTI# System Reset/Power good. This input is low when the reset switch is depressed. Otherwise, it reflects the power supply’s power good signal. This input is asynchronous to all clocks, and acts as a negative active reset. The reset circuit initiates a hard reset on the rising edge of this signal. SYSRSTO# Reset Output to System. This is the system reset signal and is used to reset the rest of the components (not on Host bus) in the system. The ISA bus reset is an externally inverted buffered version of this output and the PCI bus reset is an externally buffered version of this output. XTALI 14.3MHz Crystal Input XTALO 14.3MHz Crystal Output. These pins are connected to the 14.318 MHz crystal to provide the reference clock for the internal frequency synthesizer to generate all the other clocks. A 14.318 MHz Series Cut Crystal should be connected between these two pins. Balance capacitors of 15 pF should also be added. In the event of an external quarzt oscillator providing the master clock signal to the STPC Consumer-S device, the TTL signal should be provided on XTALO. HCLK Host Clock. This clock supplies the CPU and the host related blocks. This clock can e doubled inside the CPU and is intended to operate in the range of 25 to 100 MHz. This clock in generated internally from a PLL but can be driven directly from the external system. DCLK Dot Clock / Pixel clock. This clock supplies the display controller, the video pipeline, the ramdac, and the TV output logic. Its value is dependent on the selected display mode. Its frequency can be as high as 135 MHz. This signal is either driven by the internal PLL either by an external oscillator. The direction can be controlled by a strap option or an internal register bit. DEV_CLK 24MHz Peripheral Clock. This 24MHZ signal is provided as a convenience for the system integration of a Floppy Disk driver function in an external chip. 13/51 Release B This is preliminary information on a new product now in development or undergoing evaluation. Details are subject to change without notice. PIN DESCRIPTION 2.2.2 MEMORY INTERFACE 2.2.3 PCI INTERFACE MCLKO Memory Clock Output. This clock is driving the DIMMs on board and is generated from an internal PLL. The default value is 66MHz. PCI_CLKI 33MHz PCI Input Clock. This signal is the PCI bus clock input and should be driven from the PCI_CLKO pin. MCLKI Memory Clock Input. This clock is driving the SDRAM controller, the graphics engine and display controller. This input should be a buffered version of the MCLKO signal with the track lengths between the buffer and the pin matched with the track lengths between the buffer and the DIMMs. PCI_CLKO 33MHz PCI Output Clock. This is the master PCI bus clock output. CS#[3:0] Chip Select These signals are used to disable or enable device operation by masking or enabling all SDRAM inputs except MCLK, CKE, and DQM. AD[31:0] PCI Address/Data. This is the 32-bit multiplexed address and data bus of the PCI. This bus is driven by the master during the address phase and data phase of write transactions. It is driven by the target during data phase of read transactions. MD[63:0] Memory Data. This is the 64-bit memory data bus. MD[40-0] are read by the device strap option registers during rising edge of SYSRSTI#. CBE#[3:0] Bus Commands/Byte Enables. These are the multiplexed command and byte enable signals of the PCI bus. During the address phase they define the command and during the data phase they carry the byte enable information. These pins are inputs when a PCI master other than the STPC Consumer-S owns the bus and outputs when the STPC Consumer-S owns the bus. RAS#[1:0] Row Address Strobe. These signals enable row access and precharge. Row address is latched on rising edge of MCLK when RAS# is low. FRAME# Cycle Frame. This is the frame signal of the PCI bus. It is an input when a PCI master owns the bus and is an output when STPC Consumer-S owns the PCI bus. CAS#[1:0] Column Address Strobe. These signals enable column access. Column address is latched on rising edge of MCLK when CAS# is low. IRDY# Initiator Ready. This is the initiator ready signal of the PCI bus. It is used as an output when the STPC Consumer-S initiates a bus cycle on the PCI bus. It is used as an input during the PCI cycles targeted to the STPC Consumer-S to determine when the current PCI master is ready to complete the current transaction. MA[11:0] Memory Address. Multiplexed row and column address lines. MWE# Write Enable. Write enable specifies whether the memory access is a read (MWE# = H) or a write (MWE# = L). DQM#[7:0] Data Mask. Makes data output Hi-Z after the clock and masks the SDRAM outputs. Blocks SDRAM data input when DQM active. TRDY# Target Ready. This is the target ready signal of the PCI bus. It is driven as an output when the STPC Consumer-S is the target of the current bus transaction. It is used as an input when STPC Consumer-S initiates a cycle on the PCI bus. LOCK# PCI Lock. This is the lock signal of the PCI bus and is used to implement the exclusive bus operations when acting as a PCI target agent. 14/51 Release B This is preliminary information on a new product now in development or undergoing evaluation. Details are subject to change without notice. PIN DESCRIPTION DEVSEL# I/O Device Select. This signal is used as an input when the STPC Consumer-S initiates a bus cycle on the PCI bus to determine if a PCI slave device has decoded itself to be the target of the current transaction. It is asserted as an output either when the STPC Consumer-S is the target of the current PCI transaction or when no other device asserts DEVSEL# prior to the subtractive decode phase of the current PCI transaction. STOP# Stop Transaction. Stop is used to implement the disconnect, retry and abort protocol of the PCI bus. It is used as an input for the bus cycles initiated by the STPC Consumer-S and is used as an output when a PCI master cycle is targeted to the STPC Consumer-S. PAR Parity Signal Transactions. This is the parity signal of the PCI bus. This signal is used to guarantee even parity across AD[31:0], CBE#[3:0], and PAR. This signal is driven by the master during the address phase and data phase of write transactions. It is driven by the target during data phase of read transactions. (Its assertion is identical to that of the AD bus delayed by one PCI clock cycle) SERR# System Error. This is the system error signal of the PCI bus. It may, if enabled, be asserted for one PCI clock cycle if target aborts a STPC Consumer-S initiated PCI transaction. Its assertion by either the STPC Consumer-S or by another PCI bus agent will trigger the assertion of NMI to the host CPU. This is an open drain output. PCIREQ#[2:0] PCI Request. This pin are the three external PCI master request pins. They indicates to the PCI arbiter that the external agents desire use of the bus. PCI_GNT#[2:0] PCI Grant. These pins indicate that the PCI bus has been granted to the master requesting it on its PCIREQ#. PCI_INT[3:0] PCI Interrupt Request. These are the PCI bus interrupt signals. VDD5 5V Power Supply. These power pins are necessary for 5V ESD protection. In case the PCI bus is used in 3.3V only, these pins can be connected to 3.3V. 2.2.4 ISA INTERFACE ISA_CLK, ISA_CLKX2 ISA Clock x1, x2. These pins generate the Clock signal for the ISA bus and a Doubled Clock signal. They are also used as the multiplexor control lines for the Interrupt Controller Interrupt input lines. ISA_CLK is generated from either PCICLK/4 or OSC14M/ 2. OSC14M ISA bus synchronisation clock Output. This is the buffered 14.318 Mhz clock for the ISA bus. LA[23:17] Unlatched Address. When the ISA bus is active, these pins are ISA Bus unlatched address for 16-bit devices. When ISA bus is accessed by any cycle initiated from PCI bus, these pins are in output mode. When an ISA bus master owns the bus, these pins are in input mode. SA[19:0] ISA Address Bus. System address bus of ISA on 8-bit slot. These pins are used as an input when an ISA bus master owns the bus and are outputs at all other times. SD[15:0] I/O Data Bus. These pins are the external databus to the ISA bus. ALE Address Latch Enable. This is the address latch enable output of the ISA bus and is asserted by the STPC Consumer-S to indicate that LA2317, SA19-0, AEN and SBHE# signals are valid. The ALE is driven high during refresh, DMA master or an ISA master cycles by the STPC Consumer-S. ALE is driven low after reset. MEMR# Memory Read. This is the memory read command signal of the ISA bus. It is used as an input when an ISA master owns the bus and is an output at all other times. The MEMR# signal is active during refresh. MEMW# Memory Write. This is the memory write command signal of the ISA bus. It is used as an input when an ISA master owns the bus and is an output at all other times. SMEMR# System Memory Read. The STPC Consumer-S generates SMEMR# signal of the ISA bus only when the address is below one megabyte or the cycle is a refresh cycle. 15/51 Release B This is preliminary information on a new product now in development or undergoing evaluation. Details are subject to change without notice. PIN DESCRIPTION SMEMW# System Memory Write. The STPC Consumer-S generates SMEMW# signal of the ISA bus only when the address is below one megabyte. IOR# I/O Read. This is the IO read command signal of the ISA bus. It is an input when an ISA master owns the bus and is an output at all other times. IOW# I/O Write. This is the IO write command signal of the ISA bus. It is an input when an ISA master owns the bus and is an output at all other times. MCS16# Memory Chip Select16. This is the decode of LA23-17 address pins of the ISA address bus without any qualification of the command signal lines. MCS16# is always an input. The STPC Consumer-S ignores this signal during IO and refresh cycles. IOCS16# IO Chip Select16. This signal is the decode of SA15-0 address pins of the ISA address bus without any qualification of the command signals. The STPC Consumer-S does not drive IOCS16# (similar to PC-AT design). An ISA master access to an internal register of the STPC Consumer-S is executed as an extended 8-bit IO cycle. BHE# System Bus High Enable. This signal, when asserted, indicates that a data byte is being transferred on SD15-8 lines. It is used as an input when an ISA master owns the bus and is an output at all other times. ZWS# Zero Wait State. This signal, when asserted by addressed device, indicates that current cycle can be shortened. REF# Refresh Cycle. This is the refresh command signal of the ISA bus. It is driven as an output when the STPC Consumer-S performs a refresh cycle on the ISA bus. It is used as an input when an ISA master owns the bus and is used to trigger a refresh cycle. The STPC Consumer-S performs a pseudo hidden refresh. It requests the host bus for two host clocks to drive the refresh address and capture it in external buffers. The host bus is then relinquished while the refresh cycle continues on the ISA bus. MASTER# Add On Card Owns Bus. This signal is active when an ISA device has been granted bus ownership. AEN Address Enable. Address Enable is enabled when the DMA controller is the bus owner to indicate that a DMA transfer will occur. The enabling of the signal indicates to IO devices to ignore the IOR#/IOW# signal during DMA transfers. IOCHCK# IO Channel Check. IO Channel Check is enabled by any ISA device to signal an error condition that can not be corrected. NMI signal becomes active upon seeing IOCHCK# active if the corresponding bit in Port B is enabled. IOCHRDY Channel Ready. IOCHRDY is the IO channel ready signal of the ISA bus and is driven as an output in response to an ISA master cycle targeted to the host bus or an internal register of the STPC Consumer-S. The STPC Consumer-S monitors this signal as an input when performing an ISA cycle on behalf of the host CPU, DMA master or refresh. ISA masters which do not monitor IOCHRDY are not guaranteed to work with the STPC ConsumerS since the access to the system memory can be considerably delayed due UMA architecture. ISAOE# Bidirectional OE Control. This signal controls the OE signal of the external transceiver that connects the IDE DD bus and ISA SA bus. GPIOCS# I/O General Purpose Chip Select. This output signal is used by the external latch on ISA bus to latch the data on the SD[7:0] bus. The latch can be use by PMU unit to control the external peripheral devices or any other desired function. IRQ_MUX[3:0] Multiplexed Interrupt Request. These are the ISA bus interrupt signals. They have to be encoded before connection to the STPC Consumer-S using ISACLK and ISACLKX2 as the input selection strobes. Note that IRQ8B, which by convention is connected to the RTC, is inverted before being sent to the interrupt controller, so that it may be connected directly to the IRQ pin of the RTC. DREQ_MUX[1:0] ISA Bus Multiplexed DMA Request. These are the ISA bus DMA request signals. They are to be encoded before connection to the STPC Consumer-S using ISACLK and ISACLKX2 as the input selection strobes. 16/51 Release B This is preliminary information on a new product now in development or undergoing evaluation. Details are subject to change without notice. PIN DESCRIPTION DACK_ENC[2:0] DMA Acknowledge. These are the ISA bus DMA acknowledge signals. They are encoded by the STPC Consumer-S before output and should be decoded externally using ISACLK and ISACLKX2 as the control strobes. TC ISA Terminal Count. This is the terminal count output of the DMA controller and is connected to the TC line of the ISA bus. It is asserted during the last DMA transfer, when the byte count expires. 2.2.6 LOCAL BUS PA[21:0] Address Bus Output. PD[15:0] Data Bus. This is the 16-bit data bus. D[7:0] is the LSB and PD[15:8] is the MSB. PWR#[1:0] Write Control output. PWR0# is used to write the LSB and PWR1# to write the MSB. PRD#[1:0] Read Control output. PRD0# is used to read the LSB and PRD1# to read the MSB. 2.2.5 X-Bus Interface pins RTCAS# Real time clock address strobe. This signal is asserted for any I/O write to port 70H. RMRTCCS# ROM/Real Time clock chip select. This signal is asserted if a ROM access is decoded during a memory cycle. It should be combined with MEMR# or MEMW# signals to properly access the ROM. During a IO cycle, this signal is asserted if access to the Real Time Clock (RTC) is decoded. It should be combined with IOR or IOW# signals to properly access the real time clock. PRDY# Data Ready input. This signal is used to create wait states on the bus. When low, it completes the current cycle. FCS#[1:0] Flash Chip Select output. These are the Programmable Chip Select signals for up to 2 banks of Flash memory. IOCS#[3:0] I/O Chip Select output. These are the Programmable Chip Select signals for up to 4 external I/O devices. KBCS# Keyboard Chip Select. This signal is asserted if a keyboard access is decoded during a I/ O cycle. RTCRW# Real Time Clock RW. This pin is a multifunction pin. When ISAOE# is active, this signal is used as RTCRW#. This signal is asserted for any I/O write to port 71H. RTCDS# Real Time Clock DS. This pin is a multifunction pin. When ISAOE# is active, this signal is used as RTCDS. This signal is asserted for any I/ O read to port 71H. Note: RMRTCCS#, KBCS#, RTCRW# and RTCDS# signals must be ORed externally with ISAOE# and then connected to the external device. An LS244 or equivalent function can be used if OE# is connected to ISAOE# and the output is provided with a weak pull-up resistor as shown in Figure 2.2. 17/51 Release B This is preliminary information on a new product now in development or undergoing evaluation. Details are subject to change without notice. PIN DESCRIPTION 2.2.7 IDE INTERFACE 2.2.8 Monitor Interface PCS1#, PCS3# Primary Chip Select. These signals are used as the active high primary master & slave IDE chip select signals. These signals must be externally ANDed with the ISAOE# signal before driving the IDE devices to guarantee it is active only when ISA bus is idle. RED, GREEN, BLUE RGB Video Outputs. These are the 3 analog color outputs from the RAMDACs SCS1#, SCS3# Secondary Chip Select. These signals are used as the active high secondary master & slave IDE chip select signals. These signals must be externally ANDed with the ISAOE# signal before driving the IDE devices to guarantee it is active only when ISA bus is idle. DA[2:0] Address. These signals are connected to DA[2:0] of IDE devices directly or through a buffer. If the toggling of signals are to be masked during ISA bus cycles, they can be externally ORed with ISAOE# before being connected to the IDE devices. DD[15:0] Databus. When the IDE bus is active, they serve as IDE signals DD[11:0]. IDE devices are connected to SA[19:8] directly and ISA bus is connected to these pins through two LS245 transceivers as described in Figure 2.2. VSYNC Vertical Synchronisation Pulse. This is the vertical synchronization signal from the VGA controller. HSYNC Horizontal Synchronisation Pulse. This is the horizontal synchronization signal from the VGA controller. VREF_DAC DAC Voltage reference. An external voltage reference is connected to this pin to bias the DAC. RSET Resistor Current Set. This reference current input to the RAMDAC is used to set the fullscale output of the RAMDAC. COMP Compensation. This is the RAMDAC compensation pin. Normally, an external capacitor (typically 10nF) is connected between this pin and VDD to damp oscillations. DIORDY Busy/Ready. This pin serves as IDE signal DIORDY. PIRQ Primary Interrupt Request. SIRQ Secondary Interrupt Request. Interrupt request from IDE channels. PDRQ Primary DMA Request. SDRQ Secondary DMA Request. DMA request from IDE channels. PDACK# Primary DMA Acknowledge. SDACK# Secondary DMA Acknowledge. DMA acknoledge to IDE channels. PDIOR#, PDIOW# Primary I/O Read & Write. SDIOR#, SDIOW# Secondary I/O Read & Write. Primary & Secondary channel read & write. 18/51 Release B This is preliminary information on a new product now in development or undergoing evaluation. Details are subject to change without notice. PIN DESCRIPTION 2.2.9 VIDEO INTERFACE 2.2.10 TV OUTPUT VCLK Pixel Clock Input.This signal is used to synchronise data being transfered from an external video device to either the frame buffer, or alternatively out the TV output in bypass mode. This pin can be sourced from STPC if no external VCLK is detected, or can be input from an external video clock source. RED_TV / C_TV Analog video outputs synchronized with CVBS. This output is current-driven and must be connected to analog ground over a load resistor (RLOAD). Following the load resistor, a simple analog low pass filter is recommended. In S-VHS mode, this is the Chrominance Output. VIN[7:0] YUV Video Data Input CCIR 601 or 656. Time multiplexed 4:2:2 luminance and chrominance data as defined in ITU-R Rec601-2 and Rec656 (except for TTL input levels). This bus typically carries a stream of Cb,Y,Cr,Y digital video at VCLK frequency, clocked on the rising edge (by default) of VCLK. VCS Line synchronisation Output. This pin is an input in ODDEV+HSYNC or VSYNC + HSYNC or VSYNC slave modes and an output in all other modes (master/slave) ODD_EVEN Frame Synchronisation Ourput. This pin supports the Frame synchronisation signal. It is an input in slave modes, except when sync is extracted from YCrCbdata, and an output in master mode and when sync is extracted from YCrCb data The signal is synchronous to rising edge of DCLK. The default polarity for this pin is: - odd (not-top) field : LOW level - even (bottom) field : HIGH level GREEN_TV / Y_TV Analog video outputs synchronized with CVBS. This output is current-driven and must be connected to analog ground over a load resistor (RLOAD). Following the load resistor, a simple analog low pass filter is recommended. In S-VHS mode, this is the Luminance Output. BLUE_TV / CVBS Analog video outputs synchronized with CVBS. This output is current-driven and must be connected to analog ground over a load resistor (RLOAD). Following the load resistor, a simple analog low pass filter is recommended. In S-VHS mode, this is a second composite output. CVBS Analog video composite output (luminance/ chrominance). CVBS is current-driven and must be connected to analog ground over a load resistor (R LOAD). Following the load resistor, a simple analog low pass filter is recommended. IREF1_TV Ref. current for CVBS 10-bit DAC. IREF2_TV Reference current for RGB 9-bit DAC. VREF1_TV Ref. voltage for CVBS 10-bit DAC. VREF2_TV Reference voltage for RGB 9-bit DAC. VSSA_TV Analog VSS for DACs. VDDA_TV Analog VDD for DACs. 19/51 Release B This is preliminary information on a new product now in development or undergoing evaluation. Details are subject to change without notice. PIN DESCRIPTION 2.2.11 MISCELLANEOUS SPKRD Speaker Drive. This the output to the speaker and is AND of the counter 2 output with bit 1 of Port 61, and drives an external speaker driver. This output should be connected to 7407 type high voltage driver. SCL, SDA I C Interface. These bidirectional pins are connected to CRTC register 3Fh to implement DDC capabilities. They conform to I2C electrical specifications, they have open-collector output drivers which are internally connected to VDD through pull-up resistors. They can be used for the DDC1 (SCL) and DDC0 (SDA) lines of the VGA interface. SCAN_ENABLE Reserved. The pin is reserved for Test and Miscellaneous functions. 20/51 Release B This is preliminary information on a new product now in development or undergoing evaluation. Details are subject to change without notice. PIN DESCRIPTION Table 2.3. ISA / IDE dynamic multiplexing Table 2.4. ISA / Local Bus pin sharing . . ISA BUS (ISAOE# = 0) RMRTCCS# KBCS# RTCRW# RTCDS SA[19:8] LA[23] LA[22] SA[21] SA[20] LA[19:17] IOCHRDY IDE (ISAOE# = 1) DD[15] DD[14] DD[13] DD[12] DD[11:0] SCS3# SCS1# PCS3# PCS1# DA[2:0] DIORDY ISA / IPC SD[15:0] DREQ_MUX[1:0] LOCAL BUS PD[15:0] PA[21:20] SMEMR# MEMW# BHE# AEN ALE MEMR# IOR# IOW# REF# IOCHCK# GPIOCS# ZWS# SA[7:4] TC, DACK_ENC[2:0] SA[3] ISAOE#,SA[2:0] DEV_CLK, RTCAS# IOCS16#, MASTER# SMEMW#, MCS16# ISACLK, ISA_CLK2X PA[19] PA[18] PA[17] PA[16] PA[15] PA[14] PA[13] PA[12] PA[11] PA[10] PA[9] PA[8] PA[7:4] PA[3:0] PRDY IOCS#[3:0] FCS#[1:0] PRD#[1:0] PWR#[1:0] Figure 2.2. Typical ISA/IDE Demultiplexing 74LS245 A STPC bus / DD[15:0] MASTER# ISAOE# LA[22] LA[23] LA[22] LA[23] DIR OE B RMRTCCS# KBCS# RTCRW# RTCDS SA[19:8] PCS1# PCS3# SCS1# SCS3# 21/51 Release B This is preliminary information on a new product now in development or undergoing evaluation. Details are subject to change without notice. PIN DESCRIPTION Table 2.5. Pinout. Pin # AF3 AE4 A3 C4 G23 H24 AD11 AF15 AB23 AE16 AD15 AF16 AE17 AD16 AF17 AE18 AD17 AF18 AE19 AE20 AC19 AF22 AD21 AE24 AD23 AF23 AD22 Pin name SYSRSTI# SYSRSTO# XTALI XTALO HCLK DEV_CLK DCLK MCLKI MCLKO MA[0] MA[1] MA[2] MA[3] MA[4] MA[5] MA[6] MA[7] MA[8] MA[9] MA[10] MA[11] CS#[0] CS#[1] CS#[2] CS#[3] RAS#[0] RAS#[1] AE21 AC20 AF20 AD19 AF21 AD20 AE22 AE23 AF19 AD18 AC22 R1 T2 R3 T1 R4 U2 T3 U1 U4 V2 CAS#[0] CAS#[1] DQM#[0] DQM#[1] DQM#[2] DQM#[3] DQM#[4] DQM#[5] DQM#[6] DQM#[7] MWE# MD[0] MD[1] MD[2] MD[3] MD[4] MD[5] MD[6] MD[7] MD[8] MD[9] Pin # U3 V1 W2 V3 Y2 W4 Y1 W3 AA2 Y4 AA1 Y3 AB2 AB1 AA3 AB4 AC1 AB3 AD2 AC3 AD1 Pin name MD[10] MD[11] MD[12] MD[13] MD[14] MD[15] MD[16] MD[17] MD[18] MD[19] MD[20] MD[21] MD[22] MD[23] MD[24] MD[25] MD[26] MD[27] MD[28] MD[29] MD[30] Pin # T25 U24 T26 R25 R26 F24 D25 B20 C20 B19 A19 C19 B18 A18 B17 C18 A17 D17 B16 C17 B15 Pin name MD[59] MD[60] MD[61] MD[62] MD[63] PCI_CLKI PCI_CLKO AD[0] AD[1] AD[2] AD[3] AD[4] AD[5] AD[6] AD[7] AD[8] AD[9] AD[10] AD[11] AD[12] AD[13] AF2 AF24 AE26 AD25 AD26 AC25 AC24 AC26 AB25 AB24 AB26 AA25 Y23 AA24 AA26 Y25 Y26 Y24 W25 V23 W26 W24 V25 V26 U25 V24 U26 U23 MD[31] MD[32] MD[33] MD[34] MD[35] MD[36] MD[37] MD[38] MD[39] MD[40] MD[41] MD[42] MD[43] MD[44] MD[45] MD[46] MD[47] MD[48] MD[49] MD[50] MD[51] MD[52] MD[53] MD[54] MD[55] MD[56] MD[57] MD[58] A15 C16 B14 D15 A14 B13 D13 A13 C14 B12 C13 A12 C12 A11 D12 B10 C11 A10 D10 C10 A9 B8 A8 B7 D8 A7 C8 B6 AD[14] AD[15] AD[16] AD[17] AD[18] AD[19] AD[20] AD[21] AD[22] AD[23] AD[24] AD[25] AD[26] AD[27] AD[28] AD[29] AD[30] AD[31] CBE[0] CBE[1] CBE[2] CBE[3] FRAME# TRDY# IRDY# STOP# DEVSEL# PAR 22/51 Release B This is preliminary information on a new product now in development or undergoing evaluation. Details are subject to change without notice. PIN DESCRIPTION Pin # K24 J26 H25 H26 J24 G25 H23 D24 C26 A25 B24 Pin name SD[5] SD[6] SD[7] SD[8] SD[9] SD[10] SD[11] SD[12] SD[13] SD[14] SD[15] LA[17]/DA[0] LA[18]/DA[1] LA[19]/DA[2] LA[20]/PCS1# AD4 AF4 C9 P25 AE8 R23 P26 R24 N25 ISA_CLK ISA_CLK2X OSC14M ALE ZWS# BHE# MEMR# MEMW# SMEMR# LA[21]/PCS3# LA[22]/SCS1# LA[23]/SCS3# SA[0] SA[1] SA[2] SA[3] SA[4] SA[5] SA[6] SA[7] SA[8] SA[9] SA[10] SA[11] SA[12] SA[13] SA[14] SA[15] SA[16] SA[17] SA[18] SA[19] SD[0] SD[1] SD[2] SD[3] SD[4] N23 N26 P24 N24 M26 M25 L25 M24 L26 T24 M23 A4 P3 R2 P1 AE3 E23 D26 E24 C25 A24 B23 C23 A23 B22 D22 C5 N3 SMEMW# IOR# IOW# MCS16# IOCS16# MASTER# REF# AEN IOCHCK# IOCHRDY ISAOE# RTCAS# RTCDS# RTCRW# RMRTCCS# GPIOCS# IRQ_MUX[0] IRQ_MUX[1] IRQ_MUX[2] IRQ_MUX[3] DREQ_MUX[0] DREQ_MUX[1] DACK_ENC[0] DACK_ENC[1] DACK_ENC[2] TC SPKRD KBCS# Pin # D7 A6 D20 C21 A21 C22 A22 B21 A5 C6 B4 D5 A16 B11 B9 D18 Pin name SERR# LOCK# PCI_REQ#[0] PCI_REQ#[1] PCI_REQ#[2] PCI_GNT#[0] PCI_GNT#[1] PCI_GNT#[2] PCI_INT[0] PCI_INT[1] PCI_INT[2] PCI_INT[3] VDD5 VDD5 VDD5 VDD5 F2 G4 F3 F1 G2 G1 H2 J4 H1 H3 J2 J1 K2 J3 K1 K4 L2 K3 L1 M2 M1 L3 N2 M4 M3 P2 P4 K25 L24 K26 K23 J25 Pin # B1 C2 C1 D2 D3 D1 E2 E4 E3 E1 Pin name PIRQ SIRQ PDRQ SDRQ PDACK# SDACK# PDIOR# PDIOW# SDIOR# SDIOW# AF9 AE9 AD8 AC5 AE5 AC10 AE10 AD7 B5 C7 RED GREEN BLUE VSYNC HSYNC VREF_DAC RSET COMP SCL SDA AE15 AD5 AF7 AF5 AE6 AC7 AD6 AF6 AE7 VCLK VIN[0] VIN[1] VIN[2] VIN[3] VIN[4] VIN[5] VIN[6] VIN[7] AD10 AF11 AE12 AE13 AC12 AF14 AE11 AF12 AE14 AC14 AD12 AF8 AD9 AF13 AC9 AF10 RED_TV GREEN_TV BLUE_TV VCS ODD_EVEN CVBS IREF1_TV VREF1_TV IREF2_TV VREF2_TV VDDA_TV VDD_DAC1 VDD_DAC2 VSSA_TV VSS_DAC1 VSS_DAC2 23/51 Release B This is preliminary information on a new product now in development or undergoing evaluation. Details are subject to change without notice. PIN DESCRIPTION Pin # B3 Pin name SCAN_ENABLE G24 AD13 F25 AC17 AC15 F26 A20 C15 D6 D11 D16 D21 F4 F23 G3 G26 L4 L23 N1 VDD_CPUCLK_PLL VDD_DCLK_PLL VDD_DEVCLK_PLL VDD_MCLKI_PLL VDD_MCLKO_PLL VDD_HCLK_PLL VDD VDD VDD VDD VDD VDD VDD VDD VDD VDD VDD VDD VDD T4 T23 W1 AA4 AA23 AC6 AC2 AC11 AC16 AC21 VDD VDD VDD VDD VDD VDD VDD VDD VDD VDD E25 E26 A1:2 A26 B2 B25:26 C3 C24 D4 D9 D14 D19 D23 H4 J23 L11:16 M11:16 VSS_DLL VSS_DLL VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS Pin # N4 N11:16 P11:16 P23 R11:16 T11:16 V4 W23 AC4 AC8 AC13 AC18 AC23 AD3 AD14 AD24 AE1:2 AE25 AF1 AF25 AF26 Pin name VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS 24/51 Release B This is preliminary information on a new product now in development or undergoing evaluation. Details are subject to change without notice. STRAP OPTIONS 3 STRAP OPTIONS This chapter defines the STPC Consumer-S Strap Options and their location Memory Data Lines MD0 MD1 MD2 MD3 MD4 MD5 MD6 MD7 MD8 MD9 MD10 MD11 MD12 MD13 MD14 MD15 MD16 MD17 MD18 MD19 MD20 MD21 MD22 MD23 MD24 MD25 MD26 Note Refer to Designation Location Actual Settings 1 PCI Clock Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved PCI_CLKO Divisor Reserved Reserved Reserved Reserved Reserved Reserved HCLK PLL Speed Index 4C,bit0 Index 4C,bit 1 Index 4C,bit 2 Index 4C,bit 3 Index 4C, bit4 Index 5F, bit 0 Index 5F, bit 1 Index 5F,bit 2 Index 5F,bit 3 Index 5F,bit 4 Index 5F,bit 5 Pull up User defined Pull up Pull up Pull up Pull up Pull up Pull up User defined User defined User defined HCLK MD27 MD28 MD29 MD30 Reserved Reserved Reserved Reserved Pull down Pull down Pull down Pull down MD31 MD32 MD33 MD34 MD35 MD36 MD37 MD38 Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Pull down Pull down Pull down Pull down Pull down Pull up Pull up Pull up Set to ’0’ Set to ’1’ HCLK / 3 - HCLK / 2 - - - 000 001 010 011 100 101 110 111 25 MHz 33 MHz 100 MHz 50 MHz 60 MHz 66 MHz 75 MHz 90 MHz 25/51 Release B This is preliminary information on a new product now in developement. Details are subject to change without notice STRAP OPTIONS Memory Data Lines MD39 MD40 MD41 MD42 MD43 Note Refer to CPU Designation Actual Settings Location Reserved CPU Mode Reserved Reserved Reserved Set to ’0’ Set to ’1’ DX1 DX2 Pull up User defined Pull down Pull down Pull down Note; 1) This Strap Option selects between two different functional blocks, the first is the ISA and the other is the VGA block. 3.1 STRAP REGISTER DESCRIPTION Strap Option [16:0] are reserved. 3.1.1 STRAP REGISTER 2 INDEX 4CH (STRAP2) Bits 4-0 of this register reflect the status of pins MD[20:16] respectively. Bit 5 of this register reflect the status of pin MD[23]. Bit 4 is writeable, writes to other bits in this register have no effect. They are use by the chip as follows: Bit 4-2; Reserved Bit 1; This bit reflects the value sampled on MD[17] pin and controls the PCI clock output as follows: 0: PCI clock output = HCLK / 2 1: PCI clock output = HCLK / 3 Bit 0; Reserved This register defaults to the values sampled on MD[23] & MD[20:16] pins after reset. 3.1.2 HCLK PLL STRAP REGISTER 0 INDEX 5FH (HCLK_Strap) Bits 5-0 of this register reflect the status of pins MD[26:21] respectively. They are use by the chip as follows: Bits 5-3 These pins reflect the value sampled on MD[26:24] pins respectively and control the Host clock frequency synthesizer. Bit 2-0; Reserved This register defaults to the values sampled on above pins after reset. 26/51 Release 1.4 Release B This is preliminary information on a new product now in developement. Details are subject to change without notice STRAP OPTIONS 3.1.3 486 CLOCK PROGRAMMING (486_CLK) The bit MD[40] is used to set the clock multiplication factor of the 486 core. With the MD[40] pin pulled low the 486 will run in DX (x1) mode, while with the MD[40] pin pulled high the 486 will run in DX2 (x2) mode. The default value of the resistor on this strap input should be a resister to gnd (DX mode). Strap Options [43:41] and [39:27] are reserved. 27/51 Release B This is preliminary information on a new product now in developement. Details are subject to change without notice ELECTRICAL SPECIFICATIONS 4 ELECTRICAL SPECIFICATIONS 4.1 Introduction The electrical specifications in this chapter are valid for the STPC Consumer-S. 4.2 Electrical Connections 4.2.1 Power/Ground Connections/Decoupling Due to the high frequency of operation of the STPC Consumer-S, it is necessary to install and test this device using standard high frequency techniques. The high clock frequencies used in the STPC Consumer-S and its output buffer circuits can cause transient power surges when several output buffers switch output levels simultaneously. These effects can be minimized by filtering the DC power leads with low-inductance decoupling capacitors, using low impedance wiring, and by utilizing all of the VSS and VDD pins. be connected either to VDD or to VSS. Connect active-high inputs to VDD through a 20 kΩ (±10%) pull-down resistor and active-low inputs to VSS and connect active-low inputs to VCC through a 20 kΩ (±10%) pull-up resistor to prevent spurious operation. 4.2.3 Reserved Designated Pins Pins designated reserved should be left disconnected. Connecting a reserved pin to a pull-up resistor, pull-down resistor, or an active signal could cause unexpected results and possible circuit malfunctions. 4.2.2 Unused Input Pins All inputs not used by the designer and not listed in the table of pin connections in Chapter 3 should 4.3 Absolute Maximum Ratings The following table lists the absolute maximum ratings for the STPC Consumer-S device. Stresses beyond those listed under Table 4.1 limits may cause permanent damage to the device. These are stress ratings only and do not imply that operation under any conditions other than those specified in section ”Operating Conditions”. Exposure to conditions beyond Table 4.1 may (1) reduce device reliability and (2) result in premature failure even when there is no immediately apparent sign of failure. Prolonged exposure to conditions at or near the absolute maximum ratings (Table 4.1) may also result in reduced useful life and reliability. Table 4.1. Absolute Maximum Ratings Symbol VDDx VI , VO TSTG TOPER PTOT Parameter DC Supply Voltage Digital Input and Output Voltage Storage Temperature Operating Temperature Total Power Dissipation Value -0.3, 4.0 -0.3, VDD + 0.3 -40, +150 0, +70 4.8 Units V V °C °C W 28/51 Release B This is preliminary information on a new product now in development or undergoing evaluation. Details are subject to change without notice. ELECTRICAL SPECIFICATIONS 4.1 DC Characteristics Table 4.2. DC Characteristics Recommended Operating conditions : VDD = 3.3V Symbol VDD PDD H CLK VREF VOL VOH VIL VIH ILK C IN C OUT C CLK Parameter Operating Voltage Supply Power Internal Clock DAC Voltage Reference Output Low Voltage Output High Voltage Input Low Voltage Input High Voltage Input Leakage Current Input Capacitance Output Capacitance Clock Capacitance ±0.3V, Tcase = 0 to 100°C unless otherwise specified Test conditions Min Typ Max Unit 3.0 3.3 3.2 1.215 1.235 3.6 3.9 75 1.255 0.5 V W Mhz V V V V V V V µA pF pF pF VDD = 3.3V, HCLK = 66Mhz (Note 1) ILoad =1.5 to 8mA depending of the pin ILoad =-0.5 to -8mA depending of the pin Except XTALI XTALI Except XTALI XTALI Input, I/O (Note 2) (Note 2) (Note 2) 2.4 -0.3 -0.3 2.1 2.35 -5 0.8 0.9 VDD+0.3 VDD+0.3 5 Notes: 1. MHz ratings refer to CPU clock frequency. 2. Not 100% tested. 4.1 AC Characteristics Table 4.4 through Table 4.9 list the AC characteristics including output delays, input setup requirements, input hold requirements and output float delays. These measurements are based on the measurement points identified in Figure 4.1. The rising clock edge reference level VREF , and other reference levels are shown in Table 4.3 below for the STPC Consumer-S. Input or output signals must cross these levels during testing. Figure 4.1 shows output delay (A and B) and input setup and hold times (C and D). Input setup and hold times (C and D) are specified minimums, defining the smallest acceptable sampling window a synchronous input signal must be stable for correct operation. Table 4.3. Drive Level and Measurement Points for Switching Characteristics Symbol VREF VIHD V ILD Value 1.5 3.0 0.0 Units V V V Note: Refer to Figure 4.1. 29/51 Release B This is preliminary information on a new product now in development or undergoing evaluation. Details are subject to change without notice. ELECTRICAL SPECIFICATIONS Figure 4.1. Drive Level and Measurement Points for Switching Characteristics Tx VIHD VRef CLK: VILD A B Valid Output n OUTPUTS: MAX MIN Valid Output n+1 VRef C D VIHD Valid INPUTS: Input VRef VILD LEGEND: A B C D - Maximum Output Delay Specification - Minimum Output Delay Specification - Minimum Input Setup Specification - Minimum Input Hold Specification 30/51 Release B This is preliminary information on a new product now in development or undergoing evaluation. Details are subject to change without notice. ELECTRICAL SPECIFICATIONS Table 4.4. PCI Bus AC Timing Name t1 t2 t3 t4 t5 T6 T7 T8 T9 t10 t11 t12 t13 t14 t15 t16 t17 t18 t19 Parameter PCI_CLKI to AD[31:0] valid PCI_CLKI to FRAME# valid PCI_CLKI to CBE#[3:0] valid PCI_CLKI to PAR valid Min 2 2 2 2 Max 11 11 11 11 Unit ns ns ns ns PCI_CLKI to TRDY# valid PCI_CLKI to IRDY# valid PCI_CLKI to STOP# valid PCI_CLKI to DEVSEL# valid PCI_CLKI to PCI_GNT# valid AD[31:0] bus setup to PCI_CLKI AD[31:0] bus hold from PCI_CLKI PCI_REQ#[2:0] setup to PCI_CLKI PCI_REQ#[2:0] hold from PCI_CLKI CBE#[3:0] setup to PCI_CLKI CBE#[3:0] hold to PCI_CLKI IRDY# setup to PCI_CLKI IRDY# hold to PCI_CLKI FRAME# setup to PCI_CLKI FRAME# hold from PCI_CLKI 2 2 2 2 2 7 0 10 0 7 0 7 0 7 0 11 11 11 11 12 ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns Parameter Min Max Unit DD[15:0] setup to PIOR#/SIOR# falling DD[15:0} hold to PIOR#/SIOR# falling 15 12 Table 4.5. IDE Bus AC Timing Name t20 t21 ns ns Table 4.6. SDRAM Bus AC Timing Name Parameter Min Max Unit ns ns ns ns ns ns ns ns ns ns ns ns 31/51 Release B This is preliminary information on a new product now in development or undergoing evaluation. Details are subject to change without notice. ELECTRICAL SPECIFICATIONS Table 4.7. Video Input/TV Output AC Timing Name t35 t36 t37 t38 t39 t40 t41 t42 Parameter VIDEO_D[7:0] setup to VCLK VIDEO_D[7:0] hold from VCLK VCLK to VTV_BT# valid VCLK to VTV_HSYNC valid VTV_BT# setup to VCLK VTV_BT# hold from VCLK VTV_HSYNC setup to VCLK VTV_HSYNC hold from VCLK Min 5 2 Max 15 15 10 5 10 5 Unit ns ns ns ns ns ns ns ns Table 4.8. Graphics Adapter (VGA) AC Timing Name t43 t44 Parameter DCLK to VSYNC valid DCLK to HSYNC valid Min Max 45 45 Unit ns ns Min Max 60 60 62 35 28 60 62 50 50 50 50 50 50 Unit ns ns ns ns ns ns ns ns ns ns ns ns ns Table 4.9. ISA Bus AC Timing Name t45 t46 t47 t48 t49 t50 t51 t52 t53 t54 t55 t56 t57 Parameter XTALO to LA[23:17] bus active XTALO to SA[19:0] bus active XTALO to BHE# valid XTALO to SD[15:0] bus active PCI_CLKI to ISAOE# valid XTALO to GPIOCS# valid XTALO to ALE valid XTALO to MEMW# valid XTALO to MEMR# valid XTALO to SMEMW# valid XTALO to SMEMR# valid XTALO to IOR# valid XTALO to IOW# valid 32/51 Release B This is preliminary information on a new product now in development or undergoing evaluation. Details are subject to change without notice. MECHANICAL DATA 5. MECHANICAL DATA 5.1 388-PIN PACKAGE DIMENSION The pin numbering for the STPC 388-pin Plastic BGA package is shown in Figure 5-1. Dimensions are shown in Figure 5-2, Table 5-1 and Figure 5-3, Table 5-2. Figure 5-1. 388-Pin PBGA Package - Top View 1 3 2 5 4 7 6 9 8 11 10 13 12 15 14 17 16 19 18 21 20 23 22 25 24 26 A A B C B C D D E F E F G G H H J J K K L L M N M N P P R R T T U U V V W W Y Y AA AA AB AC AB AC AD AD AE AE AF AF 1 3 2 5 4 7 6 9 8 11 10 13 12 15 14 17 16 19 18 21 20 23 22 25 24 26 33/51 Release B MECHANICAL DATA Figure 5-2. 388-pin PBGA Package - PCB Dimensions A1 Ball Pad Corner A B A D E F Detail C G Table 5-1. 388-pin PBGA Package - PCB Dimensions Symbols A B C D E F G Min 34.95 1.22 0.58 1.57 0.15 0.05 0.75 mm Typ 35.00 1.27 0.63 1.62 0.20 0.10 0.80 Max 35.05 1.32 0.68 1.67 0.25 0.15 0.85 34/51 Release B Min 1.375 0.048 0.023 0.062 0.006 0.002 0.030 inches Typ 1.378 0.050 0.025 0.064 0.008 0.004 0.032 Max 1.380 0.052 0.027 0.066 0.001 0.006 0.034 MECHANICAL DATA Figure 5-3. 388-pin PBGA Package - Dimensions C F D E Solderball Solderball after collapse B G A Table 5-2. 388-pin PBGA Package - Dimensions Symbols A B C D E F G Min 0.50 1.12 0.60 0.52 0.63 0.60 mm Typ 0.56 1.17 0.76 0.53 0.78 0.63 30.0 Max 0.62 1.22 0.92 0.54 0.93 0.66 Min 0.020 0.044 0.024 0.020 0.025 0.024 inches Typ 0.022 0.046 0.030 0.021 0.031 0.025 11.8 Max 0.024 0.048 0.036 0.022 0.037 0.026 35/51 Release B MECHANICAL DATA 5.2 388-PIN PACKAGE THERMAL DATA 388-pin PBGA package has a Power Dissipation Capability of 4.5W which increases to 6W when used with a Heatsink. Structure in shown in Figure 5-4. Thermal dissipation options are illustrated in Figure 5-5 and Figure 5-6. Figure 5-4. 388-Pin PBGA structure Signal layers Power & Ground layers Thermal balls Figure 5-5. Thermal dissipation without heatsink Board Ambient Board dimensions: - 10.2 cm x 12.7 cm - 4 layers (2 for signals, 1 GND, 1VCC) Junction Rca Case 6 Rjc Junction 6 Board Case 8.5 125 Rjb Board Rba Ambient Ambient Rja = 13 °C/W 36/51 Release B The PBGA is centered on board There are no other devices 1 via pad per ground ball (8-mil wire) 40% copper on signal layers Copper thickness: - 17µm for internal layers - 34µm for external layers Airflow = 0 Board temperature taken at the center balls MECHANICAL DATA Figure 5-6. Thermal dissipation with heatsink Board Ambient Board dimensions: - 10.2 cm x 12.7 cm - 4 layers (2 for signals, 1 GND, 1VCC) Junction Rca Case 3 Rjc Junction 6 Board Case 8.5 50 Rjb Board Rba The PBGA is centered on board There are no other devices 1 via pad per ground ball (8-mil wire) 40% copper on signal layers Copper thickness: - 17µm for internal layers - 34µm for external layers Ambient Ambient Rja = 9.5 °C/W Airflow = 0 Board temperature taken at the center balls Heat sink is 11.1°C/W 37/51 Release B BOARD LAYOUT 6 BOARD LAYOUT 6.1 Thermal dissipation Thermal dissipation of the STPC depends mainly on supply voltage. As a result, when the system does not need to work at 3.3V, it is interresting to reduce the voltage to 3.15V for example. This may save few 100’s of mW. The second area to look at is unused interfaces and functions. Depending on the application, some input signals can be grounded, and some blocks not powered or shutdown. Clock speed dynamic adjustment is also a solution that can be used along with the integrated power management unit. The standard way to route thermal balls to internal ground layer implements only one via pad for each ball pad, connected using a 8-mil wire. With such configuration the Plastic BGA 388 package does 90% of the thermal dissipation through the ground balls, and especially the central thermal balls which are directly connected to the die, the remaining 10% is dissipated through the case. Adding a heat sink reduces this value to 85%. As a result, some basic rules has to be applied when routing the STPC in order to avoid thermal problems. First of all, the whole ground layer acts as a heat sink and ground balls must be directly connected to it as illustrated in Figure 6-1. If one ground layer is not enough, a second ground plane may be added on solder side. Figure 6-1. Ground routing Pad for ground ball Thru hole to ground layer Top L ayer : Sign Grou als nd la yer Powe r laye r Botto mLa yer : signa ls + lo cal g round layer (if ne eded ) Note: For better visibility, ground balls are not all routed. 38/51 Release B This is preliminary information on a new product now in development or undergoing evaluation. Details are subject to change without notice. BOARD LAYOUT When considering thermal dissipation, the most important - and not the more obvious - part of the layout is the connection between the ground balls and the ground layer. A 1-wire connection is shown in Figure 6-2. The use of a 8-mil wire results in a thermal resistance of 105°C/W assuming copper is used (418 W/ m.°K). This high value is due to the thickness (34 µm) of the copper on the external side of the PCB. Considering only the central matrix of 36 thermal balls and one via for each ball, the global thermal resistance is 2.9°C/W. This can be easily improved using four 10 mil wires to connect to the four vias around the ground pad link as in Figure 6-3. This gives a total of 49 vias and a global resistance for the 36 thermal balls of 0.6°C/W. The use of a ground plane like in Figure 6-4 is even better. To avoid solder wicking over to the via pads during soldering, it is important to have a solder mask of 4 mil around the pad (NSMD pad), this gives a diameter of 33 mil for a 25 mil ground pad. To obtain the optimum ground layout, place the vias directly under the ball pads. In this case no local boar d distortion is tolerated. The thickness of the copper on PCB layers is typically 34 µm for external layers and 17 µm for internal layers. That means thermal dissipation is not good and temperature of the board is concentrated around the devices and falls quickly with increased distance. When it is possible to place a metal layer inside the PCB, this improves dramatically the heat spreading and hence thermal dissipation of the board. Figure 6-2. Recommended 1-wire ground pad layout Pad for ground ball (diameter = 25 mil) Solder Mask (4 mil) Connection Wire (width = 10 mil) .5 34 Via (diameter = 24 mil) il m Hole to ground layer (diameter = 12 mil) 1 mil = 0.0254 mm Figure 6-3. Recommended 4-wire ground pad layout 4 via pads for each ground ball 39/51 Release B This is preliminary information on a new product now in development or undergoing evaluation. Details are subject to change without notice. BOARD LAYOUT Figure 6-4. Optimum layout for central ground ball Clearance = 6mil External diameter = 37 mil Via to Ground layer hole diameter = 14 mil Solder mask diameter = 33 mil Pad for ground ball diameter = 25 mil connections = 10 mil The PBGA Package dissipates also through peripheral ground balls. When a heat sink is placed on the device, heat is more uniformely spread throughout the moulding increasing heat dissipation through the peripheral ground balls. The more via pads are connected to each ground ball, the more heat is dissipated . The only limitation is the risk of lossing routing channels. Figure 6-5 shows a routing with a good trade off between thermal dissipation and number of routing channels. Figure 6-5. Global ground layout for good thermal dissipation Via to ground layer Ground pad 40/51 Release B This is preliminary information on a new product now in development or undergoing evaluation. Details are subject to change without notice. BOARD LAYOUT Figure 6-6. Bottom side layout and decoupling Ground plane for thermal dissipation Via to ground layer A local ground plane on opposite side of the board as shown in Figure 6-6 improves thermal dissipation. It is used to connect decoupling capacitances but can also be used for connection to a heat sink or to the system’s metal box for better dissipation. This possibility of using the whole system’s box for thermal dissipation is very usefull in case of high temperature inside the system and low temperature outside. In that case, both sides of the PBGA should be thermally connected to the metal chassis in order to propagate the heat flow through the metal. Figure 6-7 illustrates such implementation. Figure 6-7. Use of metal plate for thermal dissipation Die Board Metal planes Thermal conductor 41/51 Release B This is preliminary information on a new product now in development or undergoing evaluation. Details are subject to change without notice. BOARD LAYOUT 6.2 High speed signals Some Interfaces of the STPC run at high speed and have to be carefully routed or even shielded. Here is the list of these interfaces, in decreasing speed order: 1) Memory Interface. 2) Graphics and video interfaces 3) PCI bus 4) 14MHz oscillator stage All the clocks haves to be routed first and shielded for speeds of 27MHz or more. The high speed signals follow the same contrainsts, like the memory control signals and the PCI control signals. The next interfaces to be routed are Memory, Video/graphics, and PCI. All the analog noise sensitive signals have to be routed in a separate area and hence can be routed indepedently. Figure 6-8. Shielding signals ground ring shielded signal line ground pad ground pad shielded signal lines 42/51 Release B This is preliminary information on a new product now in development or undergoing evaluation. Details are subject to change without notice. BOARD LAYOUT 6.3 Memory interface 6.3.1 Introduction In order to achieve SDRAM memory interfaces which work at clock frequencies of 66MHz and above, careful consideration has to be given to the timing of the interface with all the various electrical and physical constraints taken into consideration. The guidelines described below are related to SDRAM components on DIMM modules. For ap- plications where the memories are directly soldered to the motherboard, the PCB should be laid out such that the trace lengths fit within the constraints shown here. The traces could be slightly longer since the extra routing on the DIMM PCB is no longer present but it is then up to the user to verify the timings. 6.3.2 SDRAM Clocking Scheme The SDRAM Clocking Scheme deserves a special mention here. Basically the memory clock is generated on-chip through a PLL and goes directly to the MCLKO output pin of the STPC. The nominal frequency is 66MHz. Because of the high load presented to the MCLK on the board by the DIMMs it is recommeded to rebuffer the MCLKO signal on the board and balance the skew to the clock ports of the different DIMMs and the MCLKI input pin of STPC. Figure 6-9. Clock scheme MCLKO PLL MCLKI DIMM1 MD[] register MA[] +Control DIMM2 PLL 43/51 Release B This is preliminary information on a new product now in development or undergoing evaluation. Details are subject to change without notice. BOARD LAYOUT 6.3.3 Board Layout Issues The physical layout of the motherboard PCB assumed in this presentation is as shown in Figure 6-10. Because all the memory interface signal balls are located in the same region of the STPC device it is possible to orientate the device to reduce the trace lengths. The worst case routing length to the DIMM1 is estimated to be 100mm. Figure 6-10. DIMM placement 35mm STPC 35mm SDRAMI/F 15mm DIMM4 10mm DIMM3 DIMM2 DIMM1 116mm Solid power and ground planes are a must in order to provide good return paths for the signals and to reduce EMI and noise. Also there should be ample high frequency decoupling between the power and ground planes to provide a low impedance path between the planes for the return paths for signal routings which change layers. If possible the traces should be routed adjacent to the same power or ground plane for the length of the trace. For the SDRAM interface the most critical signal is the clock. Any skew between the clocks at the SDRAM components and the memory controller will impact the timing budget. In order to get well matched clocks at all the components it is recommended that all the DIMM clock pins, STPC memory clock input (MCLKI) and any other component using the memory clock are individually driven from a low skew clock driver with matched routing lengths. This is shown in Figure 6-11. The maximum skew between pins for this part is 250ps. The important factors for the clock buffer are a consistent drive strength and low skew between the outputs. The delay through the buffer is not important so it does not have to be a zero delay pll type buffer. The trace lengths from the clock driver to the DIMM CKn pins should be matched exactly. Since the propagation speed can vary between PCB layers the clocks should be routed in a consistent way. The routing to the STPC memory input should be longer by 75mm to compensate for the extra clock routing on the DIMM. Also a 20pF capacitor should be placed as near as possible to the clock input of the STPC to compensate for the DIMM’s higher clock load. The impedance of the trace used for the clock routing should be matched to the DIMM clock trace impedance (6075W To minimise crosstalk the clocks should be routed with spacing to adjacent tracks of at least twice the clock trace width. For designs which use SDRAMs directly mounted on the motherboard PCB all the clock trace lengths should be matched exactly. The DIMM sockets should be populated starting with the furthest DIMM from the STPC device first (DIMM1). There are 2 types of DIMM devices; single row and dual row. The dual row devices require 2 chip select signals to select between the two rows. A STPC device with 4 chip select control lines could control either 4 single row DIMMs or 2 dual row DIMMs. ). 44/51 Release B This is preliminary information on a new product now in development or undergoing evaluation. Details are subject to change without notice. BOARD LAYOUT Figure 6-11. Clock routing L Low skewclock driver: DIMMCKn input DIMMCKn input MCLKO DIMMCKn input L+75mm* 20pF STPCMCLKI * No additionnal 75mm when SDRAM directly soldered on board When using DIMM modules, schematics have to be done carefully in order to avoid data busses completely crossed on the board. This has to be checked at the library level. In order to achive lay- out shown in Figure 6-12, schematics have to implement the crossing described on Figure 6-13. The DQM signals must be exchanged using the same order. Figure 6-12. Optimum data bus layout for DIMM STPC MD[63:32] MD[31:00] SDRAMI/F D[15:00] D[47:32] D[31:16] D[63:48] DIMM Figure 6-13. Schematics for optimum data bus layout for DIMM STPC DIMM MD[15:00],DQM[1:0] D[15:00],DQM[1:0] MD[31:16],DQM[3:2] D[31:16],DQM[3:2] MD[47:32],DQM[5:4] D[47:32],DQM[5:4] MD[63:48],DQM[7:6] D[63:48],DQM[7:6] 45/51 Release B This is preliminary information on a new product now in development or undergoing evaluation. Details are subject to change without notice. BOARD LAYOUT 6.3.4 Address & Control Signals This group encompasses the memory address MA[12:0], bank address BA[0,1], RAS, CAS and write enable WE signals. The load of the DIMM module on these signals is the most important oneand depends upon the type of SDRAM components used (x4, x8 or x16) and whether the DIMM module is single or dual row. The capacitive loading of the SDRAM inputs alone for an x8 single row DIMM will be about 30-40pF. An equivalent circuit for the timing simulation is shown in Figure 6-14 Most of the delays are due to the PCB traces and loading rather than the pad itself. DIMM1 DIMM2 DIMM4 100mm (0.7ns) Rterm DIMM3 Figure 6-14. Address/control equivalent circuit 10mm ZØpcb 6.3.5 Chip Select Signals (CS#[3:0]) There are 4 chip select pins per DIMM. Chip selects 0 and 2 are always used to select the first row of SDRAMs and chip selects 1 and 3 select the second row on dual bank SDRAMs. The chip select outputs only have to drive one DIMM each 130mm (0.9ns) CS[0] CS[2] DIMM Figure 6-15. CS# equivalent circuit 6.3.6 Data Write (MD[63:0]) The load on the data signals is much lower than the address/control signals for an unbuffered DIMM. For a registered DIMM the data signals are the only memory pins of the DIMM which are not registered. For the design to get maximum benefit from using registered DIMMs the timings should be compared to the timings for registered DIMMs for the other pins.. DIMM1 DIMM2 DIMM3 125mm (0.9ns) DIMM4 Figure 6-16. Data write equivalent circuit 10mm 46/51 Release B This is preliminary information on a new product now in development or undergoing evaluation. Details are subject to change without notice. BOARD LAYOUT 6.3.7 Data Read (MD[63:0]) The data read simulation circuit is shown below.. DIMM4 10W SDRAM DQ DIMM3 DIMM1 DIMM2 Figure 6-17. Data read equivalent circuit 125mm (0.9ns) 10mm 6.3.8 Data Mask (DQM[7:0]) The data mask load is quite similar to that of the data signals. 6.3.9 Summary For unbuffered DIMMs the address/control signals will be the most critical for timing unless the memory controller can be designed to set up these signals one cycle in advance. The simulations show that for these signals the best way to drive them is to use a parallel termination. For applications where speed is not so critical series termination can be used as this will save power. Using a low impedance such as 50W for these critical traces is recommended as it both reduces the delay and the overshoot. The other memory interface signals will typically be not as critical as the address/control signals for unbuffered DIMMs. When using registered DIMMs the other signals will probably be just as critical as the address/control signals so to gain maximum benefit from using registered DIMMs the timings should also be considered in that situation. Using lower impedance traces is also beneficial for the other signals but if their timing is not as critical as the address/control signals they could use the default value. Using a lower impedance implies using wider traces which may have an impact on the routing of the board. 47/51 Release B This is preliminary information on a new product now in development or undergoing evaluation. Details are subject to change without notice. ORDERING DATA 7 ORDERING DATA 7.1 Ordering Codes ST PC C03 66 BT C 3 STMicroelectronics Prefix Product Family PC: PC Compatible Product ID C03: Consumer-S Core Speed 66: 66MHz 75: 75MHz Package BT: 388 Overmoulded BGA Temperature Range C: Commercial Case Temperature (Tcase) = 0°C to +100°C I: Industrial Case Temperature (Tcase) = -40°C to +100°C Operating Voltage 3 : 3.3V ± 0.3V 48/51 Release B This is preliminary information on a new product now in development or undergoing evaluation. Details are subject to change without notice. ORDERING DATA 7.2 Available Part Numbers Part Number STPCC0366BTC3 STPCC0375BTC3 STPCC0390BTC3 STPCC0310BTC3 STPCC0366BTC3 Core Frequency ( MHz ) 66 75 90 100 66 CPU Mode ( DX / DX2 ) DX DX DX DX DX Tcase Range ( °C ) Operating Voltage (V ) 0°C to +100° 3.3V ± 0.3V -40°C to +100° 49/51 Release B This is preliminary information on a new product now in development or undergoing evaluation. Details are subject to change without notice. ORDERING DATA 50/51 Release B This is preliminary information on a new product now in development or undergoing evaluation. Details are subject to change without notice. Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express writt en approval of STMicroelectronics. 1999 STMicroelectronics - All Rights Reserved The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. STMicroelectronics GROUP OF COMPANIES Australia - Brazil - China - France - Germany - Italy - Japan - Korea - Malaysia - Malta - Mexico - Morocco - The Netherlands - Singapore Spain - Sweden - Switzerland - Taiwan - Thailand - United Kingdom - U.S.A. 51 Release B