ADVANCED INFORMATION ADVANCED INFORMATION ADVANCED INFORMATION UGB8FT AND UGB8GT ULTRAFAST SOFT RECOVERY RECTIFIER Reverse Voltage - 300 to 400 Volts Forward Current - 8.0 Amperes TO-263AB FEATURES 0.160 (4.06) 0.190 (4.83) 0.380 (9.65) 0.420 (10.67) 0.045 (1.14) 0.245 (6.22) MIN 0.055 (1.40) K 0.320 (8.13) 0.575 (14.60) 0.360 (9.14) 1 SEATING PLATE K 0.047 (1.19) 0.055 (1.40) 0.625 (15.88) 2 0.090 (2.29) 0.110 (2.79) -T- ♦ Plastic package has Underwriters Laboratories Flammability Classification 94V-0 ♦ Ideally suited for freewheeling diode power factor correction applications ♦ Soft recovery characteristics ♦ Excellent high temperature switching ♦ Optimized to reduce switching losses ♦ High temperature soldering in accordance with CECC 802 / Reflow guaranteed ♦ Glass passivated chip junction 0.018 (0.46) 0.095 (2.41) 0.025 (0.64) 0.100 (2.54) MECHANICAL DATA 0.080 (2.03) 0.027 (0.686) 0.110 (2.79) 0.037 (0.940) PIN 1 K - HEATSINK PIN 2 Dimensions are in inches and (millimeters) Case: JEDEC TO-263AB molded plastic body Terminals: Plated leads, solderable per MIL-STD-750, Method 2026 Polarity: As marked Mounting Position: Any Weight: 0.08 ounce, 2.24 grams MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified. SYMBOLS UGB8FT UGB8GT UNITS Maximum repetitive peak reverse voltage VRRM 300 400 Volts Working peak reverse voltage VRWM 225 300 Volts Maximum RMS voltage VRMS 210 280 Volts Maximum DC blocking voltage VDC 300 400 Volts Maximum average forward rectified current at TC=100°C I(AV) 8.0 Amps Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC Method) IFSM 100.0 Amps Maximum instantaneous forward voltage at IF= 8A (NOTE 1) TJ=25°C TJ=150°C VF 1.30 1.00 Volts Maximum reverse leakage current at working peak reverse voltage TC=25°C TC=100°C IR 10 350 µA Reverse recovery time at IF=1.0A, di/dt=100A/µs, VR=30V, Irr=0.1 IRM Maximum trr 50 ns trr 35 ns IRM 5.5 Amps Qrr 55 nC RΘJC 2.2 °C/W TJ, TSTG -40 to+150 °C Maximum reverse recovery time at IF=0.5A, IR=1.0A, Irr=0.25A Maximum reverse recovery current at IF=10A, di/dt=50A/µs,VR=30V Maximum stored charge IF=2A, di/dt=20A/µs, VR=30V, Irr=0.1 IRM Typical thermal resistance from junction to case Operating junction and storage temperature range NOTE: (1) Pulse test: 300µs pulse width, 1% duty cycle NOTICE: Advanced product information is subject to change without notice 4/98 TC=100°C FIG. 1 - FORWARD CURRENT DERATING CURVE FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 12 150 RESISTIVE OR INDUCTIVE LOAD PEAK FORWARD SURGE CURRENT, AMPERES AVERAGE FORWARD RECTIFIED CURRENT, AMPERES RATINGS AND CHARACTERISTIC CURVES UGB8FT AND UGB8GT 10 8.0 6.0 4.0 2.0 0 0 25 50 75 100 125 150 TC=100°C 8.3ms SINGLE HALF SINE-WAVE (JEDEC Method) 125 100 75 50 25 0 175 NUMBER OF CYCLES AT 60 Hz INSTANTANEOUS FORWARD CURRENT, AMPERES 100 TJ=25°C PULSE WIDTH=300µs 1% DUTY CYCLE 1 0.1 0.01 0.4 0.6 0.8 1.0 1.2 1.4 1.6 INSTANTANEOUS REVERSE LEAKAGE CURRENT, MICROAMPERES FIG. 3 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 10 FIG. 4 - TYPICAL REVERSE CHARACTERISTICS 1,000 TJ=125°C 100 TJ=100°C 10 1 TJ=25°C 0.1 0.01 0 FIG. 5 - REVERSE SWITCHING CHARACTERISTICS 40 60 100 60 IF=4.0A VR=30V di/dt= 150A/µs 50 di/dt=20A/µs di/dt=50A/µs di/dt=100A/µs di/dt=50A/µs di/dt=150A/µs 30 20 di/dt=20A/µs 10 trr Qrr 0 25 50 75 100 125 150 JUNCTION TEMPERATURE, °C 100 TJ=25°C f=1.0 MHZ Vsig=50mVp-p di/dt=100A/µs 40 80 FIG. 6 - TYPICAL JUNCTION CAPACITANCE 175 JUNCTION CAPACITANCE, pF RECOVERED STORED CHARGE/REVERSE RECOVERY TIME nC/ns 20 PERCENT OF RATED PEAK REVERSE VOLTAGE, % INSTANTANEOUS FORWARD VOLTAGE, VOLTS 0 100 10 1 CASE TEMPERATURE, °C 10 1 0.1 1 10 REVERSE VOLTAGE, VOLTS 100