TL064 TL064A - TL064B LOW POWER J-FET QUAD OPERATIONAL AMPLIFIERS ■ ■ ■ ■ ■ ■ ■ ■ VERY LOW POWER CONSUMPTION : 200µA WIDE COMMON-MODE (UP TO VCC+) AND DIFFERENTIAL VOLTAGE RANGES LOW INPUT BIAS AND OFFSET CURRENTS OUTPUT SHORT-CIRCUIT PROTECTION HIGH INPUT IMPEDANCE J-FET INPUT STAGE INTERNAL FREQUENCY COMPENSATION LATCH UP FREE OPERATION HIGH SLEW RATE : 3.5V/µs N DIP14 (Plastic Package) D SO14 (Plastic Micropackage) DESCRIPTION The TL064, TL064A and TL064B are high speed J-FET input quad operational amplifiers. Each of these J-FET input operational amplifiers incorporates well matched, high voltage J-FET and bipolar transistors in a monolithic integrated circuit. The device features high slew rate, low input bias and offsetcurrents, andlow offset voltage temperature coefficient. ORDER CODES Part Number Temperature Range TL064M/AM/BM -55 C, +125 C TL064I/AI/BI Package N D • • o o o o -40 C, +105 C • • 0oC, +70oC • • TL064C/AC/BC Example : TL064IN PIN CONNECTIONS (top view) Output 1 1 14 Output 4 Inverting Input 1 2 - - 13 Inverting Input 4 Non-inverting Input 1 3 + + 12 Non-inverting Input 4 11 VCC - VCC + 4 Non-inverting Input 2 5 + + 10 Non-inverting Input 3 Inverting Input 2 6 - - 9 Inverting Input 3 8 Output 3 Output 2 7 October 1997 1/10 TL064 - TL064A - TL064B SCHEMATIC DIAGRAM V CC 220Ω Non-inverting Input Inverting Input 64Ω 1/4 TL064 Output 45k Ω 270Ω 4.2k Ω 3.2k Ω 100Ω V CC MAXIMUM RATINGS Symbol Parameter TL064M,AM,BM TL064I,AI,BI TL064C,AC,BC Unit Supply Voltage - (note 1) ±18 ±18 ±18 V Vi Input Voltage - (note 3) ±15 ±15 ±15 V Vid Differential Input Voltage - (note 2) ±30 ±30 ±30 V Ptot Power Dissipation 680 680 680 mW VCC Infinite Infinite Infinite Toper Output Short-Circuit Duration (Note 4) Operating Free-Air Temperature Range -55 to +125 -40 to +105 0 to +70 o Tstg Storage Temperature Range -65 to +150 -65 to +150 -65 to +150 o C C Notes : 1. All voltage values, except differential voltage, are with respect to the zero reference level (ground) of the supply voltages where the zero reference level is the midpoint between VCC+ and VCC-. 2. Differential voltages are the non-inverting input terminal with respect to the inverting input terminal. 3. The magnitude of the input voltage must never exceed the magnitude of the supply voltage or 15 volts, whichever is less. 4. The output may be shorted to ground or to either supply. Temperature and/or supply voltages must be limited to ensure that the dissipation rating is not exceeded. 2/10 TL064 - TL064A - TL064B ELECTRICAL CHARACTERISTICS VCC = ± 15V, Tamb = 25oC (unless otherwise specified) Symbol Vio DVio Iio Iib Vicm VOPP Avd GBP Ri CMR SVR Icc VO1/VO2 PD TL064M Parameter Min. TL064I Typ. Max. Min. TL064C Typ. Max. Min. Typ. Max. Unit Input Offset Voltage (Rs = 50Ω) o Tamb = 25 C Tmin. ≤ Tamb ≤ Tmax. 3 Temperature Coefficient of Input Offset Voltage (Rs = 50Ω) 10 Input Offset Current * Tamb = 25oC Tmin. ≤ Tamb ≤ Tmax. 5 100 20 5 100 10 5 200 5 pA nA Input Bias Current * Tamb = 25oC Tmin. ≤ Tamb ≤ Tmax. 30 200 50 30 200 20 30 400 10 pA nA Input Common Mode Voltage Range Output Voltage Swing (RL = 10kΩ) o Tamb = 25 C Tmin. ≤ Tamb ≤ Tmax. Large Signal Voltage Gain (RL = 10kΩ, Vo = ± 10V) o Tamb = 25 C Tmin. ≤ Tamb ≤ Tmax. mV 6 15 3 6 9 3 15 20 o 10 µV/ C 10 V ±11.5 +15 -12 ±11.5 +15 -12 ±11 +15 -12 20 20 27 20 20 27 20 20 27 V V/mV 4 4 6 4 4 6 3 3 6 MHz Gain Bandwidth Product o (Tamb = 25 C, RL = 10kΩ CL = 100pF) 1 Input Resistance 10 1 12 1 12 10 10 12 Ω dB Common Mode Rejection Ratio (Rs = 50Ω) 80 86 80 86 70 76 Supply Voltage Rejection Ratio (Rs = 50Ω) 80 95 80 95 70 95 dB Supply Current (Per Amplifier) (Tamb = 25oC, no load, no signal) 200 Channel Separation o (Av = 100, Tamb = 25 C) 120 250 200 250 200 250 µA dB Total Power Consumption o (Tamb = 25 C, no load, no signal) 120 120 mW 6 7.5 6 7.5 6 7.5 * The input bias currents of a FET-input operational amplifier are normal junction reverse currents, which are temperature sensitive. Pulse techniques must be used that will maintain the junction temperature as close to the ambient temperature as possible. ELECTRICAL CHARACTERISTICS (continued) VCC = ± 15V, Tamb = 25oC Symbol SR tr KOV en Parameter TL064C,I,M Typ. 1.5 3.5 V/µs Rise Time (Vi = 20mV, RL = 10kΩ, CL = 100pF, AV = 1) (see Figure 1) 0.2 µs Overshoot Factor (Vi = 20mV, RL = 10kΩ, CL = 100pF, AV = 1) (see figure 1) 10 Equivalent Input Noise Voltage (Rs = 100Ω, f = 1KHz) 42 Slew Rate (Vi = 10V, RL = 10kΩ, CL = 100pF, AV = 1) Max. Unit Min. % nV √ Hz 3/10 TL064 - TL064A - TL064B ELECTRICAL CHARACTERISTICS (continued) VCC = ± 15V, Tamb = 25oC (unless otherwise specified) Symbol Vio DVio Iio Iib Parameter CMR SVR Icc VO1/VO2 PD Min. Typ. Max. Unit Temperature Coefficient of Input Offset Voltage (Rs = 50Ω) 10 Input Offset Current * Tamb = 25oC Tmin. ≤ Tamb ≤ Tmax. 5 100 3 5 100 3 pA nA Input Bias Current * Tamb = 25oC Tmin. ≤ Tamb ≤ Tmax. 30 200 7 30 200 7 pA nA mV 6 7.5 2 3 5 o µV/ C 10 ±11.5 +15 -12 ±11.5 +15 -12 Output Voltage Swing (RL = 10kΩ) o Tamb = 25 C Tmin. ≤ Tamb ≤ Tmax. 20 20 27 20 20 27 Large Signal Voltage Gain (RL = 10kΩ, Vo = ± 10V) o Tamb = 25 C Tmin. ≤ Tamb ≤ Tmax. 4 4 6 4 4 6 VOPP Ri Typ. Max. 3 Input Common Mode Voltage Range GBP Min. TL064BC,BI,BM Input Offset Voltage (Rs = 50Ω) o Tamb = 25 C Tmin. ≤ Tamb ≤ Tmax. Vicm Avd TL064AC,AI,AM V V V/mV Gain Bandwidth Product o (Tamb = 25 C, RL = 10kΩ, CL = 100pF) MHz Input Resistance 1 1 1012 1012 Ω Common Mode Rejection Ratio (R s = 50Ω) dB 80 86 80 86 80 95 80 95 Supply Voltage Rejection Ratio (Rs = 50Ω) dB Supply Current (Per Amplifier) (Tamb = 25oC, no load, no signal) 200 Channel Separation (Av = 100, Tamb = 25oC) 120 200 250 µA dB 120 mW Total Power Consumption (Each Amplifier) o (Tamb = 25 C, no load, no signal) 6 3.5 6 1.5 7.5 3.5 V/µs Rise Time (Vi = 20mV, RL = 10kΩ, CL = 100pF, AV = 1) 0.2 0.2 µs KOV Overshoot Factor (Vi = 20mV, RL = 10kΩ, CL = 100pF, AV = 1) - (see figure 1) 10 10 Equivalent Input Noise Voltage (Rs = 100Ω, f = 1KHz) 42 42 en 1.5 7.5 tr SR Slew Rate (Vi = 10V, RL = 10kΩ, CL = 100pF, AV = 1) 250 % * The input bias currents of a FET-input operational amplifier are normal junction reverse currents, which are temperature sensitive. Pulse techniques must be used that will maintain the junction temperature as close to the ambient temperature as possible. 4/10 nV √ Hz TL064 - TL064A - TL064B MAXIMUM PEAK-TO-PEAK OUTPUT VOLTAGE VERSUS SUPPLY VOLTAGE MAXIMUM PEAK-TO-PEAK OUTPUT VOLTAGE VERSUS FREE AIR TEMP. 25 R L = 1 0 kΩ T a m b= +25°C See fig ure 2 20 15 10 5 0 2 4 6 8 10 12 14 16 SUPPLY VOLTAGE (V) 15 5 Tamb = +25°C See Figure 2 0 100 200 400 700 1k 2k 4k 20 15 10 VC C = R 5 15V Ω = 10k L See Figure 2 0 -7 5 -5 0 - 25 7k 10k 25 75 15 10 5 125 R L = 10kΩ Tamb = +25°C See Figure 2 VCC = 15V VC C = 12V VCC = 5V VCC = 2V 0 10K 100K 1M 10M LARGE SIGNAL DIFFERENTIAL VOLTAGE AMPLIFICATION AND PHASE SHIFT VERSUS FREQUENCY 6 10 7 105 4 VCC = 15V R L = 10kΩ AMPLIFICATION (V/V) 10 VCC = 5V to 15V RL = 2kΩ Tamb = +25°C 4 10 3 10 102 101 -50 -25 0 25 50 75 100 FREE AIR TEMPERATURE (°C) 125 1 0 DIFFER ENTIAL VOLTAGE AMPLIFICATION (left scale) PHASE SHIFT (right scale) 10 100 45 90 135 1 -75 -50 20 1k DIFFERENTIAL VOLTAGE AMPLIFICATION (V/mV) 50 FREQUENCY (Hz) DIFFERENTIAL VOLTAGE AMPLIFICATION VERSUS FREE AIR TEMPERATURE DIFFERENTIAL VOLTAGE 25 30 LOAD RESISTANCE (kΩ) 2 0 F R EE A I R T EM P E R AT U R E ( ° C ) VOLTAGE (V) 20 MAXIMUM PEAK-TO-PEAK OUTPUT 25 VCC = 15V 25 MAXIMUM PEAK-TO-PEAK OUTPUT VOLTAGE VERSUS FREQUENCY 30 VOLTAGE (V) MAXIMUM PEAK-TO-PEAK OUTPUT MAXIMUM PEAK-TO-PEAK OUTPUT VOLTAGE VERSUS LOAD RESISTANCE 10 30 MAXIMUM PEAK-TO-PEAKOUTPUT VOLTAGE (V) MAXIMUM PEAK-TO-PEAKOUTPUT VOLTAGE (V) 30 1k 10k 100k 1M 180 10M FREQUENCY (Hz) 5/10 TL064 - TL064A - TL064B SUPPLY CURRENT PER AMPLIFIER VERSUS SUPPLY VOLTAGE SUPPLY CURRENT PER AMPLIFIER VERSUS FREE AIR TEMPERATURE 250 SUPPLY CURRENT (µA) SUPPLY CURRENT (µA) 250 200 150 100 T amb = +25°C No signal 50 200 150 100 VCC = 15V 50 No signal No load No load 0 0 0 2 4 10 12 6 8 SUPPLY VOLTAGE ( V) 14 -75 16 TOTAL POWER DISSIPATED VERSUS FREE AIR TEMPERATURE COMMON MODE REJECTION RATIO VERSUS FREE AIR TEMPERATURE 30 87 25 20 15 10 VCC = 15V 5 No signal No load 0 -75 -50 -25 0 25 50 75 100 125 COMMON MODE REJECTION RATIO (dB) TOTAL POWER DISSIPATED (mW) -25 0 25 50 75 100 125 FREE AIR TEMPERATURE (°C) -50 86 85 84 83 VC C = 82 R 81 -75 -50 FREE AIR TEMPERATURE (°C) -25 0 25 L 50 1 5V = 1 0kΩ 75 100 125 FREE AIR TEMPERATURE (°C) NORMALIZED UNITY GAIN BANDWIDTH SLEW RATE, AND PHASE SHIFT VERSUS TEMPERATURE INPUT BIAS CURRENT VERSUS FREE AIR TEMPERATURE 1.1 S LEW RAT E (left scale) 1 0.9 0.8 0.7 -75 R L = 10kΩ f = B1for phase shift -25 1.01 1 0.99 VCC = 15V -50 1.02 0 0.98 25 50 0.97 75 100 125 FREE AIR TEMPERATURE (°C) INPUT BIAS CURRENT (nA) 1.2 PHASE SHIFT (right scale) UNITY -GAIN-BANDWIDTH (left scale) 1.03 NORMALIZED PHASESHIFT NORMALIZED UNITY-GAIN BANDWIDTH AND SLEW RATE 100 1.3 VCC = 15V 10 1 0.1 0.01 -50 -25 0 25 50 75 100 FREE AIR TEMPERATURE (°C) 6/10 125 TL064 - TL064A - TL064B OUTPUT VOLTAGE VERSUS ELAPSED TIME 6 28 INPUT 4 OUTPUT VOLTAGE (mV) 24 2 OUTPUT 0 VCC = 15V R L = 10kΩ -2 CL = 100pF Tamb = +25°C -4 OVERSHOOT 20 90% 16 12 8 V 4 10% t 0 -6 0 2 4 6 TIME (µs) 8 r 0.2 CC = 15V R L = 10k Ω Tamb = +25°C 0 -4 0.4 0.6 0.8 1 12 14 TIME ( µs) 10 EQUIVALENT INPUT NOISE VOLTAGE VERSUS FREQUENCY 100 90 EQUIVALENT INPUT NOISE VOLTAGE (nV/VHz) (V) INPUT AND OUTPUT VOLTAGES VOLTAGE FOLLOWER LARGE SIGNAL RESPONSE 15V VC C = R S = 100Ω T a m b = +25°C 80 70 60 50 40 30 20 10 0 40 10 100 400 1k 4k 10k 40k 100k FREQUENCY (Hz) 7/10 TL064 - TL064A - TL064B PARAMETER MEASUREMENT INFORMATION Figure 1 : Voltage follower Figure 2 : Gain-of-10 inverting amplifier 10k Ω 10k Ω 1k Ω 1k Ω - eI - eI 1/4 1/4 eo TL064 CL = 100pF RL eo TL064 RL CL = 100pF TYPICAL APPLICATION AUDIO DISTRIBUTION AMPLIFIER fO = 1 00 kHz 1/ 4 1M Ω TL0 64 Output A 1 µF 1/ 4 - TL064 1 /4 Input TL064 100k 1OO Ω Ω 100k Ω 100k V CC+ µF 100k Ω 1/ 4 TL0 64 8/10 Output B Output C TL064 - TL064A - TL064B PM-DIP14.EPS PACKAGE MECHANICAL 14 PINS - PLASTIC DIP a1 B b b1 D E e e3 F i L Z Min. 0.51 1.39 Millimeters Typ. Max. 1.65 Min. 0.020 0.055 0.5 0.25 Inches Typ. 0.065 0.020 0.010 20 0.787 8.5 2.54 15.24 0.335 0.100 0.600 7.1 5.1 0.280 0.201 3.3 1.27 Max. DIP14.TBL Dimensions 0.130 2.54 0.050 0.100 9/10 TL064 - TL064A - TL064B PM-SO14.EPS PACKAGE MECHANICAL 14 PINS - PLASTIC MICROPACKAGE (SO) A a1 a2 b b1 C c1 D E e e3 F G L M S Min. Millimeters Typ. 0.1 0.35 0.19 Max. 1.75 0.2 1.6 0.46 0.25 Min. Inches Typ. 0.004 0.014 0.007 0.5 Max. 0.069 0.008 0.063 0.018 0.010 0.020 o 45 (typ.) 8.55 5.8 8.75 6.2 0.336 0.228 1.27 7.62 3.8 4.6 0.5 0.334 0.244 0.050 0.300 4.0 5.3 1.27 0.68 0.150 0.181 0.020 0.157 0.208 0.050 0.027 o 8 (max.) SO14.TBL Dimensions 1997 SGS-THOMSON Microelectronics – Printed in Italy – All Rights Reserved SGS-THOM SON Microelectronics GROUP OF COMPANIES Australia - Brazil - Canada - China - France - Germany - Hong Kong - Italy - Japan - Korea - Malaysia - Malta - Morocco The Netherlands - Singapore - Spain - Sweden - Switzerland - Taiwan - Thailand - United Kingdom - U.S.A. 10/10 ORDER CODE : Information furnished is believed to be accurate and reliable. However, SGS-THOMSON Microelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of SGS-THOMSON Microelectronics. Specification mentioned in this pub lication are subject to change without notice. This publication supersedes and replaces all information previously supplied. SGS-THOMSON Microelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of SGS-THOMSON Microelectronics.