STMICROELECTRONICS TL062CDT

TL062, TL062A, TL062B
Low-power JFET dual operational amplifiers
Datasheet − production data
Features
■
Very low power consumption: 200 µA
■
Wide common-mode (up to VCC+) and
differential voltage ranges
■
Low input bias and offset currents
■
Output short-circuit protection
■
High input impedance JFET input stage
■
Internal frequency compensation
■
Latch up free operation
■
High slew rate: 3.5 V/µs
N
DIP8
(plastic package)
D
SO-8
(plastic micropackage)
Description
The TL062, TL062A and TL062B devices are
high-speed JFET input single operational
amplifiers. Each of these JFET input operational
amplifiers incorporates well matched,
high-voltage JFET and bipolar transistors in
a monolithic integrated circuit.
The devices feature high slew rates, low input
bias and offset currents, and a low offset voltage
temperature coefficient.
Pin connections
(top view)
1
8
2
-
3
+
4
1
2
3
4
5
6
7
8
September 2012
This is information on a product in full production.
Doc ID 2294 Rev 4
7
-
6
+
5
- Output 1
- Inverting input 1
- Non-inverting input 1
- VCC- Non-inverting input 2
- Inverting input 2
- Output 2
- VCC+
1/15
www.st.com
15
Schematic diagram
TL062, TL062A, TL062B
1
Schematic diagram
Figure 1.
Schematic diagram
2/15
Doc ID 2294 Rev 4
TL062, TL062A, TL062B
2
Absolute maximum ratings and operating conditions
Absolute maximum ratings and operating conditions
Table 1.
Absolute maximum ratings
Symbol
VCC
Vi
Parameter
Unit
±18
V
±15
V
±30
V
680
mW
Supply voltage(1)
Input voltage
(2)
Vid
Differential input voltage
Ptot
Power dissipation
Output short-circuit
Tstg
Value
(3)
duration(4)
Infinite
Storage temperature range
°C
(5) (6)
Rthja
Thermal resistance junction-to-ambient ,
SO-8
DIP8
125
85
°C/W
Rthjc
Thermal resistance junction-to-case(5),(6)
SO-8
DIP8
40
41
°C/W
HBM: human body model(7)
900
V
150
V
1.5
kV
ESD
MM: machine
model(8)
CDM: charged device
model(9)
1. All voltage values, except differential voltage, are with respect to the zero reference level (ground) of the
supply voltages where the zero reference level is the midpoint between VCC+ and VCC-.
2. The magnitude of the input voltage must never exceed the magnitude of the supply voltage or 15 volts,
whichever is less.
3. Differential voltages are the non-inverting input terminal with respect to the inverting input terminal.
4. The output may be shorted to ground or to either supply. Temperature and/or supply voltages must be
limited to ensure that the dissipation rating is not exceeded.
5. Short-circuits can cause excessive heating and destructive dissipation.
6. Rth are typical values.
7. Human body model: 100 pF discharged through a 1.5 kΩ resistor between two pins of the device, done for
all couples of pin combinations with other pins floating.
8. Machine model: a 200 pF capacitor is charged to the specified voltage, then discharged directly between
two pins of the device with no external series resistor (internal resistor < 5 Ω), done for all couples of pin
combinations with other pins floating.
9. Charged device model: all pins plus package are charged together to the specified voltage and then
discharged directly to ground.
Table 2.
Symbol
Operating conditions
Parameter
VCC
Supply voltage range
Toper
Operating free air temperature range
TL062I, AI, BI
TL062C, AC, BC
6 to 36
Doc ID 2294 Rev 4
-40 to +105
Unit
V
0 to +70
°C
3/15
Electrical characteristics
TL062, TL062A, TL062B
3
Electrical characteristics
Table 3.
VCC = ±15 V, Tamb = +25 °C (unless otherwise specified)
TL062I
Symbol
TL062C
Parameter
Unit
Min.
Typ.
Max.
Input offset voltage (RS = 50 Ω)
Tamb = +25 °C
Tmin ≤ Tamb ≤ Tmax
3
6
9
Temperature coefficient of input offset voltage
(R S = 50 Ω)
10
Iio
Input offset current(1)
Tamb = +25 °C
Tmin ≤ Tamb ≤ Tmax
5
100
10
5
200
5
pA
nA
Iib
Input bias current(1)
Tamb = +25 °C
Tmin ≤ Tamb ≤ Tmax
30
200
20
30
400
10
pA
nA
Vio
DVio
Input common mode voltage range
±11.5
Vopp
Output voltage swing (R L = 10 kΩ)
Tamb = +25 °C
Tmin ≤ Tamb ≤ Tmax
20
20
27
Avd
Large signal voltage gain
RL = 10 kΩ, Vo = ±10 V,
Tamb = +25 °C
Tmin ≤ Tamb ≤ Tmax
4
4
6
GBP
Ri
Gain bandwidth product
Tamb = +25 °C, RL =10 kΩ, CL = 100 pF
Input resistance
Typ.
Max.
3
15
20
mV
μV/°C
10
+15
-12
Vicm
Min.
+15
-12
V
20
20
27
V
3
3
6
±11.5
V/mV
1
1
MHz
1012
1012
Ω
CMR
Common mode rejection ratio
RS = 50 Ω
80
86
70
76
dB
SVR
Supply voltage rejection ratio
RS = 50 Ω
80
95
70
95
dB
ICC
Vo1/Vo2
Supply current, no load
Tamb = +25 °C, no load, no signal
200
Channel separation
Av = 100, Tamb = 25 °C
120
PD
Total power consumption
Tamb = +25 °C, no load, no signal
SR
Slew rate
Vi = 10 V, RL = 10 kΩ, CL= 100 pF, Av = 1
4/15
6
1.5
Doc ID 2294 Rev 4
3.5
250
200
250
120
7.5
6
1.5
3.5
μA
dB
7.5
mW
V/μs
TL062, TL062A, TL062B
Table 3.
Electrical characteristics
VCC = ±15 V, Tamb = +25 °C (unless otherwise specified) (continued)
TL062I
Symbol
TL062C
Parameter
Unit
Min.
Typ.
Max.
Min.
Typ.
Max.
Rise time
Vi = 20 mV, RL = 10 kΩ,
CL = 100 pF, Av = 1
0.2
0.2
μs
Kov
Overshoot factor (see Figure 15)
Vi = 20 mV, RL = 10 kΩ, CL = 100 pF, Av = 1
10
10
%
en
Equivalent input noise voltage
RS = 100 Ω, f = 1 kHz
42
42
nV
-----------Hz
tr
1. The input bias currents of a FET-input operational amplifier are normal junction reverse currents, which are temperature
sensitive. Pulse techniques must be used that will maintain the junction temperature as close to the ambient temperature
as possible.
Table 4.
VCC = ±15 V, Tamb = +25 °C (unless otherwise specified)
TL062AC, AI
Symbol
TL062BC, BI
Parameter
Unit
Min.
Typ.
Max.
Input offset voltage (RS = 50 Ω)
Tamb = +25 °C
Tmin ≤ Tamb ≤ Tmax
3
3
7.5
Temperature coefficient of input offset voltage
(RS = 50 Ω)
10
Iio
Input offset current(1)
Tamb = +25 °C
Tmin ≤ Tamb ≤ Tmax
5
100
3
5
100
3
pA
nA
Iib
Input bias current(1)
Tamb = +25 °C
Tmin ≤ Tamb ≤ Tmax
30
200
7
30
200
7
nA
Vio
DVio
Max.
2
3
5
10
+15
-12
±11.5
+15
-12
Output voltage swing (RL = 10 kΩ)
Tamb = +25 °C
Tmin ≤ Tamb ≤ Tmax
20
20
27
20
20
27
Large signal voltage gain
RL = 10 kΩ, Vo = ±10 V,
Tamb = +25 °C
Tmin ≤ Tamb ≤ Tmax
4
4
6
4
4
6
Input common mode voltage range
Vopp
Avd
Ri
Typ.
±11.5
Vicm
GBP
Min.
Gain bandwidth product
Tamb = +25 °C, RL =10 kΩ, CL = 100 pF
Input resistance
mV
µV/°C
V
V/mV
1
1
MHz
1012
1012
Ω
CMR
Common mode rejection ratio
RS = 50 Ω
80
86
80
86
dB
SVR
Supply voltage rejection ratio
RS = 50 Ω
80
95
80
95
dB
Doc ID 2294 Rev 4
5/15
Electrical characteristics
Table 4.
TL062, TL062A, TL062B
VCC = ±15 V, Tamb = +25 °C (unless otherwise specified) (continued)
TL062AC, AI
Symbol
Unit
Min.
ICC
Vo1/Vo2
TL062BC, BI
Parameter
Typ.
Max.
Supply current, no load
Tamb = +25 °C, no load, no signal
200
250
Channel separation
Av = 100, Tamb = +25 °C
120
PD
Total power consumption
Tamb = +25 °C, no load, no signal
SR
Slew rate
Vi = 10 V, RL = 10 kΩ, CL = 100 pF, Av = 1
6
1.5
3.5
Min.
Typ.
Max.
200
250
µA
7.5
mW
120
7.5
6
1.5
3.5
V/μs
tr
Rise time
Vi = 20 mV, R L = 10 kΩ, CL = 100 pF, Av = 1
0.2
0.2
μs
Kov
Overshoot factor (see Figure 15)
Vi = 20 mV, R L = 10 kΩ, CL = 100 pF, Av = 1
10
10
%
en
Equivalent input noise voltage
RS = 100 Ω, f = 1 kHz
42
42
nV
-----------Hz
1. The input bias currents of a FET-input operational amplifier are normal junction reverse currents, which are temperature
sensitive. Pulse techniques must be used that will maintain the junction temperature as close to the ambient temperature
as possible.
6/15
Doc ID 2294 Rev 4
TL062, TL062A, TL062B
Figure 3.
Maximum peak-to-peak output
voltage versus free air temperature
Maximum peak-to-peak output
voltage (V)
Maximum peak-to-peak output
voltage versus supply voltage
Maximum peak-to-peak output
voltage (V)
Figure 2.
Electrical characteristics
RL = 10 kΩ
Tamb = + 25 °C
VCC = +/- 15 V
RL = 10 kΩ
Free air temperature (°C)
Supply voltage (V)
Figure 5.
Maximum peak-to-peak output
voltage versus frequency
Maximum peak-to-peak output
voltage (V)
Maximum peak-to-peak output
voltage versus load resistance
Maximum peak-to-peak output
voltage (V)
Figure 4.
VCC = +/- 15 V
Tamb = + 25 °C
VCC = +/- 12 V
VCC = +/- 5 V
VCC = +/- 2 V
Frequency (Hz)
Load resistance (kΩ)
Differential voltage amplification
versus free air temperature
Figure 7.
Large signal differential voltage
amplification and phase shift
versus frequency
10
6
10
7
105
Differential voltage
amplification (V/V)
Differential voltage
amplification (V/mV)
Figure 6.
RL = 10 kΩ
Tamb = + 25 °C
VCC = +/- 15 V
4
2
VCC = +/- 15 V
RL = 10 kΩ
VCC = +/- 5 V to +/- 15 V
RL = 2 kΩ
Tamb = + 25 °C
Differential
voltage
amplification
(left scale)
4
10
3
10
102
101
-50
-25
0
25
50
75
100
125
Free air temperature (°C)
1
45
90
Phase shift
(right scale)
135
1
-75
0
10
100
1k
10k
100k
1M
180
10M
Frequency (Hz)
Doc ID 2294 Rev 4
7/15
Electrical characteristics
TL062, TL062A, TL062B
250
250
200
200
Supply current (μA)
Supply current per amplifier versus Figure 9.
supply voltage
Supply current (μA)
Figure 8.
150
100
Tamb = + 25 °C
No signal
no load
50
Supply current per amplifier versus
free air temperature
150
100
VCC = +/- 15 V
50
No signal
no load
0
0
0
2
4
6
8
10
12
14
-75
16
-50
Figure 10. Total power dissipated versus free
air temperature
20
No signal
no load
15
10
5
0
-75
-50
-25
0
25
50
75
50
25
100 125
75
Figure 11. Common-mode rejection ratio
versus free air temperature
Common mode rejection ratio
(dB)
Total power dissipated
(mW)
30
VCC = +/- 15 V
0
Free air temperature (°C)
Supply voltage (+/- V)
25
-25
100
87
86
85
84
83
VCC = +/- 15 V
82
81
-75
125
RL = 10 kΩ
-50
-25
0
25
50
75
100
125
Free air temperature (°C)
Free air temperature (°C)
Figure 12. Normalized unity gain bandwidth
slew rate and phase shift versus
temperature
Figure 13. Input bias current versus free air
temperature
Unity-gain bandwidth
(left scale)
1.1
Slew rate
(left scale)
1
0.9
0.8
1.03
1.02
1.01
1
0.99
VCC = +/- 15 V
RL = 10 kΩ
0.98
f = B1 for phase shift
0.7
-75 -50
-25
0
25
50
0.97
75 100 125
Input bias current (nA)
1.2
Phase shift
(right scale)
Normalized phase shift
Normalized unity-gain bandwidth
and slew rate
100
1.3
VCC = +/- 15 V
10
1
0.1
0.01
-50
-25
0
25
50
75
Free air temperature (°C)
Free air temperature (°C)
8/15
Doc ID 2294 Rev 4
100
125
TL062, TL062A, TL062B
Electrical characteristics
Figure 15. Output voltage versus elapsed time
6
28
24
Input
4
2
Output voltage (mV)
Input and output voltages (V)
Figure 14. Voltage follower large signal pulse
response
Output
0
VCC = +/- 15 V
-2
RL = 10 kΩ
-4
Tamb = + 25 °C
CL = 100 pF
Overshoot
20
90%
16
12
8
VCC = +/- 15 V
4
0
RL = 10 kΩ
10%
-6
0
2
4
6
8
Tamb = + 25 °C
tr
-4
0
10
0.2
0.6
0.4
0.8
1
12
14
Time (μs)
Time (μs)
Figure 16. Equivalent input noise voltage versus frequency
Equivalent input noise
voltage (nV/VHz)
100
90
80
70
60
50
40
30
VCC = +/- 15 V
RS = 100 Ω
Tamb = + 25 °C
20
10
0
10
40
100
400 1k
4k
10k
40k 100k
Frequency (Hz)
Parameter measurement information
Figure 17. Voltage follower
Figure 18. Gain of 10 inverting amplifier
10 kΩ
1 kΩ
-
eI
1/2
TL062
eI
eo
CL = 100 pF
RL = 10 kΩ
Doc ID 2294 Rev 4
-
1/2
TL062
eo
RL
CL = 100 pF
9/15
Typical applications
4
TL062, TL062A, TL062B
Typical applications
Figure 19. 100 kHz quadrature oscillator
1N 4148
18 pF
18 pF
18 k Ω (1)
-15 V
1 kΩ
-
1/2
88.4 k Ω
-
TL062
88.4 k Ω
1/2
TL062
6 sin ω t
6 cos ω t
1 kΩ
18 pF
88.4 k Ω
1N 4148
18 k Ω(1)
+15 V
1. These resistor values may be adjusted for a symmetrical output.
10/15
Doc ID 2294 Rev 4
TL062, TL062A, TL062B
5
Package information
Package information
In order to meet environmental requirements, ST offers these devices in different grades of
ECOPACK® packages, depending on their level of environmental compliance. ECOPACK
specifications, grade definitions and product status are available at: www.st.com. ECOPACK
is an ST trademark.
Doc ID 2294 Rev 4
11/15
Package information
5.1
TL062, TL062A, TL062B
DIP8 package information
Figure 20. DIP8 package outline
Table 5.
DIP8 package mechanical data
Dimensions
Symbol
Millimeters
Min.
Typ.
A
Min.
Typ.
Max.
0.210
A1
0.38
A2
2.92
3.30
4.95
0.115
0.130
0.195
b
0.36
0.46
0.56
0.014
0.018
0.022
b2
1.14
1.52
1.78
0.045
0.060
0.070
c
0.20
0.25
0.36
0.008
0.010
0.014
D
9.02
9.27
10.16
0.355
0.365
0.400
E
7.62
7.87
8.26
0.300
0.310
0.325
E1
6.10
6.35
7.11
0.240
0.250
0.280
0.015
e
2.54
0.100
eA
7.62
0.300
L
12/15
Max.
5.33
eB
Note:
Inches
10.92
2.92
3.30
3.81
0.430
0.115
0.130
0.150
Dimensions "D" and "E1" do not include mold flash, protrusions or gate burrs. Mold flash,
protrusions or gate burrs shall not exceed 0.25 mm in total (both sides). Datum plane "H"
coincides with the bottom of the lead, where the lead exits the body.
Doc ID 2294 Rev 4
TL062, TL062A, TL062B
5.2
Package information
SO-8 package information
Figure 21. SO-8 package outline
Table 6.
SO-8 package mechanical data
Dimensions
Symbol
Millimeters
Min.
Typ.
A
Inches
Max.
Min.
Typ.
1.75
0.069
A1
0.10
A2
1.25
b
0.28
0.48
0.011
0.019
c
0.17
0.23
0.007
0.010
D
4.80
4.90
5.00
0.189
0.193
0.197
E
5.80
6.00
6.20
0.228
0.236
0.244
E1
3.80
3.90
4.00
0.150
0.154
0.157
e
0.25
Max.
0.004
0.010
0.049
1.27
0.050
h
0.25
0.50
0.010
0.020
L
0.40
1.27
0.016
0.050
L1
k
ccc
1.04
0
0.040
8°
0.10
Doc ID 2294 Rev 4
1°
8°
0.004
13/15
Ordering information
6
TL062, TL062A, TL062B
Ordering information
Table 7.
Order codes
Part number
Temperature
range
Package
Packaging
Marking
DIP8
Tube
TL062IN
TL062AIN
TL062BIN
TL062ID/IDT
TL062AID/AIDT
TL062BID/BIDT
SO-8
Tube or
tape and reel
062I
062AI
062BI
TL062CN
TL062ACN
TL062BCN
DIP8
Tube
TL062CN
TL062ACN
TL062BCN
SO-8
Tube or
tape and reel
062C
062AC
062BC
TL062IN
TL062AIN
TL062BIN
-40 °C, +105 °C
0 °C, +70 °C
TL062CD/CDT
TL062ACD/ACDT
TL062BCD/BCDT
7
Revision history
Table 8.
Document revision history
Date
Revision
28-Mar-2001
1
Initial release.
27-Jul-2007
2
Added values for Rthja and Rthjc in Table 1: Absolute maximum
ratings.
Added Table 2: Operating conditions.
Updated format.
15-Mar-2010
3
Updated document format.
Added TL062A and TL062B in title on cover page.
Updated package information in Chapter 5.
4
Removed TL062M, AM, BM /TL062I, AI, BI / TL062C, AC, BC part
numbers and temperature ranges from Table 1. and TL062M, AM,
BM from Table 2.
Removed TL062M, updated min. “Input common mode voltage
range” for TL062C device in Table 3.
Removed TL062AM and TL062BM devices, updated max. ”Input
offset voltage - Tamb” for TL062AC, AI devices in Table 4.
Removed TL062MN, TL062AMN, TL062BMN, TL062MD/MDT,
TL062AMD/AMDT, TL062BMD/BMDT part numbers from Table 7.
Minor corrections throughout document.
21-Sep-2012
14/15
Changes
Doc ID 2294 Rev 4
TL062, TL062A, TL062B
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY TWO AUTHORIZED ST REPRESENTATIVES, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2012 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
Doc ID 2294 Rev 4
15/15