HS5A THRU HS5M 5.0 AMPS. High Efficient Surface Mount Rectifiers Voltage Range 50 to 1000 Volts Current 5.0 Amperes SMC/DO-214AB Features Glass passivated junction chip. For surface mounted application Low forward voltage drop Low profile package Built-in stain relief, ideal for automatic placement Fast switching for high efficiency High temperature soldering: 260℃/10 seconds at terminals Plastic material used carries Underwriters Laboratory Classification 94V-O .129(3.27) .118(3.0) .245(6.22) .220(5.59) .280(7.11) .260(6.60) .012(.31) .006(.15) .103(2.62) .079(2.00) Mechanical Data Cases: Molded plastic Terminals: Solder plated Polarity: Indicated by cathode band Packing: 16mm tape per E1A STD RS-481 Weight: 0.21 gram .008(.20) .004(.10) .060(1.52) .030(0.76) .320(8.13) .305(7.75) Dimensions in inches and (millimeters) Maximum Ratings and Electrical Characteristics Rating at 25℃ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% Symbol HS HS HS Type Number 5A 5B 5D Maximum Recurrent Peak Reverse Voltage VRRM 50 100 200 Maximum RMS Voltage VRMS 35 70 140 Maximum DC Blocking Voltage VDC 50 100 200 Maximum Average Forward Rectified Current See Fig. 2 Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method ) Maximum Instantaneous Forward Voltage @ 5.0A Maximum DC Reverse Current @ TA=25℃ at Rated DC Blocking Voltage @ TA=100℃ Maximum Reverse Recovery Time (Note 1) Typical Junction Capacitance (Note 2) Maximum Thermal Resistance (Note 3) Operating Temperature Range Storage Temperature Range HS 5F 300 210 300 HS 5G 400 280 400 HS 5J 600 420 600 HS HS Units 5K 5M 800 1000 V 560 700 V 800 1000 V I(AV) 5.0 A IFSM 150 A VF 1.0 1.3 1.7 V 75 50 uA uA nS pF 10.0 200 IR Trr Cj 50 80 RθJA TJ TSTG 60 ℃/W -55 to +150 -55 to +150 ℃ ℃ Notes: 1. Reverse Recovery Test Conditions: IF=0.5A, IR=1.0A, IRR=0.25A 2. Measured at 1 MHz and Applied VR=4.0 Volts 3. Mounted on P.C.B. with 0.6”x0.6” ( 16 x 16 mm ) Copper Pad Areas. - 306 - RATINGS AND CHARACTERISTIC CURVES (HS5A THRU HS5M) FIG.1- REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM 10W NONINDUCTIVE FIG.2- MAXIMUM FORWARD CURRENT DERATING CURVE trr AVERAGE FORWARD CURRENT. (A) 50W NONINDUCTIVE +0.5A (-) DUT (+) 50Vdc (approx) (-) PULSE GENERATOR (NOTE 2) 1W NON INDUCTIVE OSCILLOSCOPE (NOTE 1) 0 -0.25A (+) -1.0A NOTES: 1. Rise Time=7ns max. Input Impedance= 1 megohm 22pf 2. Rise Time=10ns max. Sourse Impedance= 50 ohms 1cm SET TIME BASE FOR 5/ 10ns/ cm FIG.3- TYPICAL REVERSE CHARACTERISTICS 6.0 5.0 4.0 3.0 SINGLE PHASE HALF WAVE 60Hz RESISTIVE OR INDUCTIVE LOAD 0.375" (9.5mm) LEAD LENGTH 2.0 1.0 0 0 25 50 75 100 125 150 175 o AMBIENT TEMPERATURE. ( C) FIG.4- TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 100 100 Tj=25 0C 10 1 0.1 0 20 40 60 80 100 120 S5 -H 10 1.0 0.1 0.01 140 0 PERCENT OF RATED PEAK REVERSE VOLTAGE. (%) 0.2 0.4 0.6 0.8 1.0 1.2 1.4 FORWARD VOLTAGE. (V) FIG.6- TYPICAL JUNCTION CAPACITANCE FIG.5- MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT 175 300 150 JUNCTION CAPACITANCE.(pF) PEAK FORWARD SURGE CURRENT. (A) 5A Tj=25 0C HS Tj=100 0C HS HS 5G 5J -H S5 M INSTANTANEOUS FORWARD CURRENT. (A) INSTANTANEOUS REVERSE CURRENT. ( A) D 1000 200 100 0 125 100 HS HS 75 5J- 5A- HS HS 5G 5M 50 25 0 1 10 100 1000 0.1 0.5 1 2 5 10 20 REVERSE VOLTAGE. (V) NUMBER OF CYCLES AT 60Hz - 307 - 50 100 200 500 1000