SFAF1601G THRU SFAF1608G Isolation 16.0 AMPS. Glass Passivated Super Fast Rectifiers Voltage Range 50 to 600 Volts Current 16.0 Amperes ITO-220AC Features .185(4.7) .406(10.3) .173(4.4) Low forward voltage drop High current capability High reliability High surge current capability .390(9.90) .124(3.16) .118(3.00) .13 4(3. 4)D IA . 112 (2. 85) . 11 3(3. 0)D IA . 100 (2.5 5) .2 72( 6. 9) .2 48( 6. 3) . 606(1 5.5 ) . 583(1 4.8 ) Mechanical Data .0 63 (1 .6 ) Cases: ITO-220AC molded plastic Epoxy: UL 94V-O rate flame retardant Terminals: Leads solderable per MILSTD-202, Method 208 guaranteed Polarity: As marked High temperature soldering guaranteed: 260oC/10 seconds .16”,(4.06mm) from case. Weight: 2.24 grams MA X .161(4.1) .146(3.7) .110( 2.8) . 071 (1. 8) . 543( 13. 8) MA X . 512( 13. 2) .0 98(2 .5) 2 PIN 1 . 10 0( 2 . 55) . 100 (2.5 5) PIN 2 Case Positive Dimensions in inches and (millimeters) Maximum Ratings and Electrical Characteristics Rating at 25℃ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% Symbol SFAF SFAF SFAF SFAF Type Number SFAF SFAF SFAF SFAF Units 1601G 1602G 1603G 1604G 1605G 1606G 1607G 1608G Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current @TC = 100℃ Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method ) Maximum Instantaneous Forward Voltage @ 16.0A Maximum DC Reverse Current @ TA=25℃ at Rated DC Blocking Voltage @ TA=100℃ Maximum Reverse Recovery Time (Note 1) Typical Junction Capacitance (Note 2) Typical Thermal Resistance C (Note 3) VRRM VRMS VDC 50 35 50 100 150 200 300 400 500 600 70 105 140 210 280 350 420 100 150 200 300 400 500 600 V V V I(AV) 16.0 A IFSM 200 A 0.975 VF 1.3 IR 10 400 Trr 35 Cj 130 1.3 RθJC Operating Temperature Range TJ -65 to +150 Storage Temperature Range TSTG -65 to +150 Notes: 1. Reverse Recovery Test Conditions: IF=0.5A, IR=1.0A, IRR=0.25A 2. Measured at 1 MHz and Applied Reverse Voltage of 4.0 V D.C. 3. Mounted on Heatsink Size of 3 in x 5 in x 0.25 in Al-Plate. - 278 - 1.7 V uA uA nS 100 pF ℃/W ℃ ℃ RATINGS AND CHARACTERISTIC CURVES (SFAF1601G THRU SFAF1608G) FIG.1- REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM 10W NONINDUCTIVE 50W NONINDUCTIVE trr +0.5A (-) DUT (+) 50Vdc (approx) (-) PULSE GENERATOR (NOTE 2) 1W NON INDUCTIVE OSCILLOSCOPE (NOTE 1) 0 -0.25A (+) -1.0A NOTES: 1. Rise Time=7ns max. Input Impedance= 1 megohm 22pf 2. Rise Time=10ns max. Sourse Impedance= 50 ohms 1cm 20 16 12 8 4 00 50 100 150 o 100 TJ=100 0C TJ=75 0C 10 1 TJ=25 0C 250 Tj=25 0C 200 0.1 8.3ms Single Half Sine Wave JEDEC Method 0 20 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE. (%) 150 FIG.6- TYPICAL FORWARD CHARACTERISTICS 100 100 20 50 100 NUMBER OF CYCLES AT 60Hz FIG.5- TYPICAL JUNCTION CAPACITANCE 300 Tj=25 0C 250 200 SF AF 150 100 SF AF 16 01 G~ SF AF 05 50 0 16 G~ SF AF 16 16 04 2 5 G 10 10 3 1 0.3 0.1 0.03 G 08 1 30 0.01 0.4 20 16 10 SF AF 5 SF AF 16 2 160 1G ~ 0 1 04G SF AF 16 07 05 G~ G ~S SF FA AF F1 16 60 08 G 6G 50 SF AF PEAK FORWARD SURGE CURRENT. (A) FIG.4- MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT INSTANTANEOUS REVERSE CURRENT. ( A) 1000 CASE TEMPERATURE. ( C) CAPACITANCE.(pF) FIG.3- TYPICAL REVERSE CHARACTERISTICS INSTANTANEOUS FORWARD CURRENT. (A) AVERAGE FORWARD CURRENT. (A) FIG.2- MAXIMUM FORWARD CURRENT DERATING CURVE SET TIME BASE FOR 5/ 10ns/ cm 50 100 200 500 1000 REVERSE VOLTAGE. (V) - 279 - Tj=25oC Pulse Width=300 s 1% Duty Cycle 0.6 0.8 1.0 1.2 1.4 FORWARD VOLTAGE. (V) 1.6 1.8