RG10 - RG10Y SUPER FAST RECTIFIER DIODES PRV : 70 - 600 Volts Io : 1.0 - 1.5 Amperes D2 FEATURES : * * * * * * * High current capability High surge current capability High reliability Low reverse current Low forward voltage drop Super fast recovery time Pb / RoHS Free 0.161 (4.1) 0.154 (3.9) 1.00 (25.4) MIN. 0.284 (7.2) 0.268 (6.8) 0.034 (0.86) 0.028 (0.71) MECHANICAL DATA : * Case : D2 Molded plastic * Epoxy : UL94V-O rate flame retardant * Lead : Axial lead solderable per MIL-STD-202, Method 208 guaranteed * Polarity : Color band denotes cathode end * Mounting position : Any * Weight : 0.465 gram 1.00 (25.4) MIN. Dimensions in inches and ( millimeters ) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Rating at 25 °C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20%. RATING SYMBOL RG10Y RG10 RG10A UNIT Maximum Recurrent Peak Reverse Voltage VRRM 70 400 600 V Maximum RMS Voltage VRMS 49 280 420 V Maximum Reverse Voltage VDC 70 400 600 V IF(AV) 1.5 1.2 1.0 A Maximum Average Forward Current 0.375"(9.5mm) Lead Length Ta = 55 °C Maximum Peak Forward Surge Current, 8.3ms Single half sine wave Superimposed on rated load (JEDEC Method) Maximum Peak Forward Voltage at IF = 1.0 A. IFSM VF 50 1.1 1.8 A 2.0 V Maximum DC Reverse Current Ta = 25 °C IR 5 µA at Rated DC Blocking Voltage Ta = 100 °C IR(H) 50 µA Maximum Reverse Recovery Time ( Note 1 ) Trr 35 ns Typical Junction Capacitance ( Note 2 ) CJ 50 pf Junction Temperature Range TJ - 65 to + 150 °C Storage Temperature Range TSTG - 65 to + 150 °C Notes : ( 1 ) Reverse Recovery Test Conditions : IF = 0.5 A, IR = 1.0 A, Irr = 0.25 A. ( 2 ) Measured at 1.0 MHz and applied reverse voltage of 4.0 VDC Page 1 of 2 Rev. 02 : March 25, 2005 RATING AND CHARACTERISTIC CURVES ( RG10 - RG10Y ) FIG.1 - REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM 50 Ω 10 Ω Trr + 0.5 D.U.T. + 0 PULSE GENERATOR ( NOTE 2 ) 50 Vdc (approx) 1Ω - 0.25 OSCILLOSCOPE ( NOTE 1 ) - 1.0 A SET TIME BASE FOR 15 ns/cm NOTES : 1. Rise Time = 7 ns max., Input Impedance = 1 megaohm, 22 pF. 1 cm 2. Rise time = 10 ns max., Source Impedance = 50 ohms. FIG.2 - DERATING CURVE FOR OUTPUT RECTIFIED CURRENT FIG.3 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 50 100 PEAK FORWARD SURGE CURRENT, AMPERES PERCENTAGE AGAINST RATED CURRENT Io (%) 3. All Resistors = Non-inductive Types. 80 60 40 20 8.3 ms SINGLE HALF SINE WAVE Ta = 50 °C 40 30 20 10 60Hz RESISTIVE OR INDUCTIVE LOAD 0 0 25 50 75 100 125 150 0 175 1 AMBIENT TEMPERATURE, ( °C) FORWARD CURRENT, AMPERES 100 10 RG10 1.0 RG10A 0.1 Pulse Width = 300 µs 2% Duty Cycle 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 6 10 20 40 60 100 2.2 10 TJ = 100 °C 1.0 0.1 TJ = 25 °C 0.01 0 20 40 60 80 100 120 140 PERCENT OF RATED REVERSE VOLTAGE, (%) TJ = 25 °C 0.01 0.4 4 FIG.5 - TYPICAL REVERSE CHARACTERISTICS REVERSE CURRENT, MICROAMPERES FIG.4 - TYPICAL FORWARD CHARACTERISTICS RG10Y 2 NUMBER OF CYCLES AT 60Hz 2.4 FORWARD VOLTAGE, VOLTS Page 2 of 2 Rev. 02 : March 25, 2005