Freescale Semiconductor Advance Information Document Number: MC33399 Rev. 8.0, 10/2006 Local Interconnect Network (LIN) Physical Interface 33399 Local Interconnect Network (LIN) is a serial communication protocol designed to support automotive networks in conjunction with Controller Area Network (CAN). As the lowest level of a hierarchical network, LIN enables cost-effective communication with sensors and actuators when all the features of CAN are not required. The 33399 is a Physical Layer component dedicated to automotive sub-bus applications. It offers speed communication from 1.0 kbps to 20 kbps, and up to 60 kbps for Programming Mode. It has two operating modes: Normal and Sleep. The 33399 supports LIN Protocol Specification 1.3. LIN PHYSICAL INTERFACE Features • Nominal Operation from VSUP 7.0 V to 18 V DC, Functional up to 27 V DC Battery Voltage and Capable of Handling 40 V During Load Dump • Active Bus Waveshaping to Minimize Radiated Emission • ± 5.0 kV ESD on LIN Bus Pin, ± 4.0 kV ESD on Other Pins • 30 kΩ Internal Pullup Resistor • Ground Shift Operation and Ground Disconnection Fail-Safe at Module Level • An Unpowered Node Does Not Disturb the Network • 20 µA in Sleep Mode • Wake-Up Capability from LIN Bus, MCU Command and Dedicated High Voltage Wake-Up Input (Interface to External Switch) • Interface to MCU with CMOS-Compatible I/O Pins • Control of External Voltage Regulator • Pb-FREE packaging designated by package code EF D SUFFIX EF SUFFIX (PB-FREE) 98ASB42564B 8 PIN SOICN ORDERING INFORMATION Device MCZ33399EF/R2 Regulator 12 V 33399 VSUP INH WAKE GND EN MCU TXD RXD LIN LIN Bus Figure 1. 33399 Simplified Application Diagram * This document contains certain information on a new product. Specifications and information herein are subject to change without notice. © Freescale Semiconductor, Inc., 2006. All rights reserved. Package - 40°C to 125°C 8 SOICN MC33399D/R2 V PWR 5.0 V Temperature Range (TA) INTERNAL BLOCK DIAGRAM INTERNAL BLOCK DIAGRAM VSUP WAKE INF Wake-Up VREG Control EN VREF Bias 30 kΩ Logic RXD Receiver LIN Protection TXD Driver GND Figure 2. 33399 Simplified Internal Block Diagram 33399 2 Analog Integrated Circuit Device Data Freescale Semiconductor PIN CONNECTIONS PIN CONNECTIONS RXD 1 8 INH EN 2 7 VSUP WAKE 3 6 LIN TXD 4 5 GND Figure 3. 33399 8-SOICN Pin Connections Table 1. 8-SOICN Pin Definitions A functional description of each pin can be found in the Functional Pin Description section beginning on page 10. Pin Pin Name Formal Name Definition 1 RXD Data Output 2 EN Enable Control 3 WAKE Wake Input High voltage input used to wake up the device from the Sleep mode. 4 TXD Data Input MCU interface that controls the state of the LIN output. 5 GND Ground Device ground pin. 6 LIN LIN Bus Bidirectional pin that represents the single-wire bus transmitter and receiver. 7 VSUP Power Supply Device power supply pin. 8 INH Inhibit Output Controls an external switchable voltage regulator having an inhibit input. MCU interface that reports the state of the LIN bus voltage. Controls the operation mode of the interface. 33399 Analog Integrated Circuit Device Data Freescale Semiconductor 3 ELECTRICAL CHARACTERISTICS MAXIMUM RATINGS ELECTRICAL CHARACTERISTICS MAXIMUM RATINGS Table 2. Maximum Ratings All voltages are with respect to ground unless otherwise noted. Exceeding these ratings may cause a malfunction or permanent damage to the device. Rating Symbol Value Unit ELECTRICAL RATINGS Power Supply Voltage VSUP Continuous Supply Voltage V 27 40 Transient Voltage (Load Dump) WAKE DC and Transient Voltage (Through a 33 kΩ Serial Resistor) VWAKE - 18 to 40 V Logic Voltage (RXD, TXD, EN Pins) VLOG - 0.3 to 5.5 V LIN Pin VBUS DC Voltage V - 18 to 40 - 150 to 100 Transient (Coupled Through 1.0 nF Capacitor) INH Voltage / Current VINH DC Voltage ESD Voltage, Human Body Model (1) - 0.3 to VSUP + 0.3 V ESD1 V All Pins ± 4000 LIN Bus Pin with Respect to Ground ± 5000 ESD Voltage, Machine Model V ESD2 All Pins V V ± 200 THERMAL RATINGS °C Operating Temperature Ambient TA - 40 to 125 Junction TJ - 40 to 150 TSTG - 55 to 165 °C RθJA 150 °C/W TPPRT Note 3. °C Thermal Shutdown TSHUT 150 to 200 °C Thermal Shutdown Hysteresis THYST 8.0 to 20 °C Storage Temperature Thermal Resistance, Junction to Ambient Peak Package Reflow Temperature During Reflow (2) (3) , Notes 1. ESD1 testing is performed in accordance with the Human Body Model (CZAP = 100 pF, RZAP = 1500 Ω), ESD2 testing is performed in accordance with the Machine Model (CZAP = 220 pF, RZAP = 0 Ω). 2. 3. Pin soldering temperature limit is for 10 seconds maximum duration. Not designed for immersion soldering. Exceeding these limits may cause malfunction or permanent damage to the device. Freescale’s Package Reflow capability meets Pb-free requirements for JEDEC standard J-STD-020C. For Peak Package Reflow Temperature and Moisture Sensitivity Levels (MSL), Go to www.freescale.com, search by part number [e.g. remove prefixes/suffixes and enter the core ID to view all orderable parts. (i.e. MC33xxxD enter 33xxx), and review parametrics. 33399 4 Analog Integrated Circuit Device Data Freescale Semiconductor ELECTRICAL CHARACTERISTICS STATIC ELECTRICAL CHARACTERISTICS STATIC ELECTRICAL CHARACTERISTICS Table 3. Static Electrical Characteristics Characteristics noted under conditions 7.0 V ≤ VSUP ≤ 18 V, -40°C ≤ TA ≤ 125°C, GND = 0 V unless otherwise noted. Typical values noted reflect the approximate parameter means at TA = 25°C under nominal conditions unless otherwise noted. Characteristic Symbol Min Typ Max Unit VSUP 7.0 13.5 18 V VLIN > VSUP - 0.5 V, VSUP < 14 V IS1 — 20 50 14 V < VSUP < 18 V IS2 — — 150 IS(REC) — — 2.0 IS(DOM) — — 3.0 VSUP_UV 5.5 6.4 6.8 0.0 — 0.9 3.75 — 5.25 VSUP PIN (DEVICE POWER SUPPLY) Supply Voltage Range µA Supply Current in Sleep Mode Supply Current in Normal Mode Recessive State Dominant State, Total Bus Load > 500 Ω Supply Undervoltage Threshold mA V RXD OUTPUT PIN (LOGIC) Low-Level Output Voltage IIN ≤ 1.5 mA High-Level Output Voltage IOUT ≤ 250 µΑ VOL V VOH V TXD INPUT PIN (LOGIC) Low-Level Input Voltage VIL — — 1.5 V High-Level Input Voltage VIH 3.5 — — V VINHYST 100 550 800 mV - 50 — - 25 Input Voltage Threshold Hysteresis Pullup Current Source µA IPU 1.0 V < VTXD < 4.0 V, VEN = 5.0 V EN INPUT PIN (LOGIC) Low-Level Input Voltage VIL — — 1.5 V High-Level Input Voltage VIH 3.5 — — V VINHYST 100 480 800 mV 5.0 20 30 — 20 40 — 20 — Input Voltage Threshold Hysteresis EN Low-Level Input Current High-Level Input Current 1.0 V < EN < 4.0 V µA IIH VIN = 4.0 V Pulldown Current µA IIL VIN = 1.0 V µA IPD 33399 Analog Integrated Circuit Device Data Freescale Semiconductor 5 ELECTRICAL CHARACTERISTICS STATIC ELECTRICAL CHARACTERISTICS Table 3. Static Electrical Characteristics (continued) Characteristics noted under conditions 7.0 V ≤ VSUP ≤ 18 V, -40°C ≤ TA ≤ 125°C, GND = 0 V unless otherwise noted. Typical values noted reflect the approximate parameter means at TA = 25°C under nominal conditions unless otherwise noted. Characteristic Symbol Min Typ Max Unit LIN PIN (VOLTAGE EXPRESSED VERSUS VSUP VOLTAGE) Low-Level Bus Voltage (Dominant State) VDOM TXD LOW, VLIN = 40 mA V 0.0 — 1.4 0.85 VSUP — — - 40°C ≤ TA ≤ 70°C 20 30 47 70°C < TA ≤ 125°C 35 49 60 50 150 200 0.0 — 10 VSUP Disconnected, -18 V ≤ VLIN ≤ 18 V (Excluding Internal Pullup Source) - 40 — 40 VSUP Disconnected, VLIN = -18 V (Including Internal Pullup Source) — - 600 — VSUP Disconnected, VLIN = +18 V (Including Internal Pullup Source) — 15 — 0 VSUP — 0.4 VSUP 0.6 VSUP — VSUP — VSUP/2 — 0.05 VSUP — 0.15 VSUP V LINWU 3.5 4.5 6.0 V High-Level Voltage (Normal Mode) VWUH VSUP - 0.8 — VSUP V Leakage Current (Sleep Mode) I LEAK High-Level Voltage (Recessive State) VREC TXD HIGH, IOUT = 1.0 µA Internal Pullup Resistor to VSUP (4) RPU Current Limitation kΩ I LIM TXD LOW, VLIN = VSUP Leakage Current to GND Recessive State, VSUP - 0.3 V ≤ VLIN ≤ VSUP V mA µA I LEAK (4) LIN Receiver, Low-Level Input Voltage V LINL TXD HIGH, RXD LOW LIN Receiver, High-Level Input Voltage V LINH TXD HIGH, RXD HIGH LIN Receiver Threshold Center V V LINHYS VLINH - VLINL LIN Wake-Up Threshold Voltage V V LINTH (VLINH - VLINL) / 2 LIN Receiver Input Voltage Hysteresis V V INH OUTPUT PIN 0 < VINH < VSUP µA 0 — 5.0 HIGH-to-LOW Transition 0.3 VSUP 0.43 VSUP 0.55 VSUP LOW-to-HIGH Transition 0.4 VSUP 0.55 VSUP 0.65 VSUP 0.1 VSUP 0.16 VSUP 0.2 VSUP WAKE INPUT PIN Typical Wake-Up Threshold (EN = 0 V, 7.0 V ≤ VSUP ≤ 18 V) (5) Wake-Up Threshold Hysteresis WAKE Input Current VWUTH VWUHYS V V µA I WU VWAKE ≤ 14 V — 1.0 5.0 VWAKE > 14 V — — 100 Notes 4. A diode structure is inserted with the pullup resistor to avoid parasitic current path from LIN to VSUP. 5. When VSUP is greater than 18 V, the wake-up voltage thresholds remain identical to the wake-up thresholds at 18 V. 33399 6 Analog Integrated Circuit Device Data Freescale Semiconductor ELECTRICAL CHARACTERISTICS DYNAMIC ELECTRICAL CHARACTERISTICS DYNAMIC ELECTRICAL CHARACTERISTICS Table 4. Dynamic Electrical Characteristics Characteristics noted under conditions 7.0 V ≤ VSUP ≤ 18 V, -40°C ≤ TA ≤ 125°C, GND = 0 V unless otherwise noted. Typical values noted reflect the approximate parameter means at TA = 25°C under nominal conditions unless otherwise noted. Characteristic Symbol Min Typ Max Falling Edge t FALL 0.75 2.0 3.0 Rising Edge t RISE 0.75 2.0 3.0 t SYM - 2.0 — 2.0 Unit DIGITAL INTERFACE TIMING LIN Slew Rate (6) , (7) V/µs LIN Rise/Fall Symmetry (t RISE - t FALL) Driver Propagation Delay (8) , (9) µs µs TXD LOW-to-LIN LOW t TXDLINL 0.0 — 4.0 TXD HIGH-to-LIN HIGH t TXDLINH 0.0 — 4.0 LIN LOW to RXD LOW t RXDLINL 2.0 4.0 6.0 LIN HIGH to RXD HIGH t RXDLINH 2.0 4.0 6.0 t RECSYM - 2.0 — 2.0 µs Transmitter Propagation Delay Symmetry t TRSYM - 2.0 — 2.0 µs (11) t PROPWL 45 70 130 Receiver Propagation Delay (9) , (10) Receiver Propagation Delay Symmetry Propagation Delay LIN Bus Wake-Up to INH HIGH µs µs Notess 6. Measured between 20 and 80 percent of bus signal for 10 V < VSUP < 18 V. Between 30 and 70 percent of signal for 7.0 V < VSUP < 10 V. 7. 8. 9. 10. 11. See Figure 5, page 8. t TXDLINL is measured from TXD (HIGH-to-LOW) and LIN (VREC - 0.2 V). t TXDLINH is measured from TXD (LOW-to-HIGH) and LIN (VDOM + 0.2 V). See Figure 4, page 8. Measured between LIN receiver thresholds and RXD pin. See Figure 6, page 8. 33399 Analog Integrated Circuit Device Data Freescale Semiconductor 7 ELECTRICAL CHARACTERISTICS TIMING DIAGRAMS TIMING DIAGRAMS TXD Recessive State Recessive State VREC LIN VREC - 0.2 V t TXDLINL 0.6 VSUP 0.4 VSUP VDOM VDOM + 0.2 V Dominant State RXD t RXDLINH t TXDLINH t RXDLINL Figure 4. Normal Mode Bus Timing Characteristics t FALL 0.8 VSUP 0.2 VSUP t RISE Recessive State VSUP LIN 0.4 VSUP Dominant State 0.8 VSUP INH 0.2 VSUP Figure 5. LIN Rise and Fall Time t PROPWL Figure 6. LIN Bus Wake-Up 33399 8 Analog Integrated Circuit Device Data Freescale Semiconductor FUNCTIONAL DIAGRAMS TIMING DIAGRAMS FUNCTIONAL DIAGRAMS WAKE State Change LIN Bus INH INH High Low or Floating High Low or Floating WAKE Filtering Time Bus Wake-Up Filtering Time ( t PROGWL) Voltage Regulator Voltage Regulator On State Off State Node in Operation Regulator Wake-Up Time Delay EN Regulator Wake-Up Time Delay EN EN High Node in Sleep State On State Off State Node in Operation EN High Node in Sleep State MCU Startup Time Delay MCU Startup Time Delay Figure 8. LIN Wake-Up from Wake-Up Switch Figure 7. LIN Wake-Up with INH Option LIN Bus INH (previous Wake-Up) Low or Floating High Wake-Up Filtering Time (t PROGWL) Voltage Reg On State Wake-Up from Stop Mode Node In Operation EN High EN State MCU in Stop Mode MCU Stop Mode Recovery/Startup Time Delay I/O(2) IRQ Low High Impedance / I/O in Input State High Low High Figure 9. LIN Wake-Up with MCU in Stop Mode 33399 Analog Integrated Circuit Device Data Freescale Semiconductor 9 FUNCTIONAL DESCRIPTION TIMING DIAGRAMS FUNCTIONAL DESCRIPTION INTRODUCTION The 33399 is a Physical Layer component dedicated to automotive LIN sub-bus applications. The 33399 features include speed communication from 1.0 kbps to 20 kbps, up to 60 kbps for Programming Mode, and active bus waveshaping to minimize radiated emission. The device offers three different wake-up capabilities: wake-up from LIN bus, wake-up from the MCU command, and dedicated high voltage wake-up input. The INH output may be used to control an external voltage regulator. FUNCTIONAL PIN DESCRIPTION POWER SUPPLY PIN (VSUP) The VSUP power supply pin is connected to a battery through a serial diode for reverse battery protection. The DC operating voltage is from 7.0 V to 27 V. This pin sustains standard automotive voltage conditions such as 27 V DC during jump-start conditions and 40 V during load dump. To avoid a false bus message, an undervoltage reset circuitry disables the transmission path (from TXD to LIN) when VSUP falls below 7.0 V. Supply current in the Sleep mode is typically 20 µA. This charge-up is achieved by the total system pullup current resistors. In order to guarantee that the rise time is within specification, maximum bus capacitance should not exceed 10 nF with bus total pullup resistance less than 1.0 kΩ. Receiver Characteristics The receiver thresholds are ratiometric with the device supply pin. Typical threshold is 50%, with a hysteresis between 5% and 10% of VSUP. DATA INPUT PIN (TXD) GROUND PIN (GND) In case of a ground disconnection at the module level, the 33399 does not have significant current consumption on the LIN bus pin when in the recessive state. (Less than 100 µA is sourced from LIN bus pin, which creates 100 mV drop voltage from the 1.0 kΩ LIN bus pullup resistor.) For the dominant state, the pullup resistor should always be active. The 33399 handles a ground shift up to 3.0 V when VSUP > 9.0 V. Below 9.0 V VSUP, a ground shift can reduce VSUP value below the minimum VSUP operation of 7.0 V. The TXD input pin is the MCU interface that controls the state of the LIN output. When TXD is LOW, LIN output is LOW; when TXD is HIGH, the LIN output transistor is turned OFF. This pin has an internal 5.0 V internal pullup current source to set the bus in a recessive state in case the MCU is not able to control it; for instance, during system power-up/ power-down. During the Sleep mode, the pullup current source is turned OFF. DATA OUTPUT PIN (RXD) LIN BUS PIN (LIN) The LIN bus pin represents the single-wire bus transmitter and receiver. Transmitter Characteristics The LIN driver is a low-side MOSFET with internal current limitation and thermal shutdown. An internal pullup resistor with a serial diode structure is integrated so no external pullup components are required for the application in a slave node. An additional pullup resistor of 1.0 kΩ must be added when the device is used in the master node. Voltage can go from - 18 V to 40 V without current other than the pullup resistance. The LIN pin exhibits no reverse current from the LIN bus line to VSUP, even in the event of GND shift or VPWR disconnection. LIN thresholds are compatible with the LIN protocol specification. The fall time from recessive to dominant and the rise time from dominant to recessive are controlled to typically 2.0 V/µs. The symmetry between rise and fall time is also guaranteed. When going from dominant to recessive, the bus impedance parasitic capacitor must be charged up to VSUP. The RXD output pin is the MCU interface that reports the state of the LIN bus voltage. LIN HIGH (recessive) is reported by a high level on RXD; LIN LOW (dominant) is reported by a low voltage on RXD. RXD output structure is a CMOS-type push-pull output stage. ENABLE INPUT PIN (EN) The EN pin controls the operation mode of the interface. If EN = logic [1], the interface is in normal mode, with the transmission path from TXD to LIN and from LIN to RXD both active. If EN = logic [0], the device is in Sleep mode or low power mode, and no transmission is possible. In Sleep mode, the LIN bus pin is held at VSUP through the bus pullup resistors and pullup current sources. The device can transmit only after being awakened. Refer to the INHIBIT OUTPUT PIN (INH) description on page 11. During Sleep mode, the device is still supplied from the battery voltage (through VSUP pin). Supply current is 20 µA typical. Setting the EN pin to LOW will turn the INH to high impedance. The EN pin has an internal 20 µA pulldown current source to ensure the device is in Sleep mode if EN floats. 33399 10 Analog Integrated Circuit Device Data Freescale Semiconductor FUNCTIONAL DESCRIPTION TIMING DIAGRAMS INHIBIT OUTPUT PIN (INH) The INH pin controls an external switchable voltage regulator having an inhibit input. This pin is a high-side switch structure to VSUP. When the device is in the Normal mode, the inhibit high-side switch is turned ON and the external voltage regulator is activated. When the device is in Sleep mode, the inhibit switch is turned OFF and disables the voltage regulator (if this feature is used). A wake-up event on the LIN bus line will switch the INH pin to VSUP level. Wake-up output current capability is limited to 280 µA. INH can also drive an external MOSFET connected to an MCU IRQ or XIRQ input to generate an interrupt. See the typical application illustrated in Figure 13, page 15. WAKE INPUT PIN (WAKE) The WAKE pin is a high-voltage input used to wake up the device from Sleep mode. WAKE is usually connected to an external switch in the application. The typical WAKE thresholds are VSUP / 2. The WAKE pin has a special design structure and allows wake-up from both HIGH-to-LOW or LOW-to-HIGH transitions. When entering the Sleep mode, the LIN monitors the state of the WAKE pin and stores it as a reference state. The opposite state of this reference state will be the wake-up event used by the device to re-enter Normal mode. An internal filter is implemented (50 µs typical filtering time delay). The WAKE pin input structure exhibits a high impedance with extremely low input current when voltage at this pin is below 14 V. When voltage at the WAKE pin exceeds 14 V, input current starts to sink into the device. A series resistor should be inserted in order to limit the input current, mainly during transient pulses. Recommended resistor value is 33 kΩ. Important The WAKE pin should not be left open. If the wake-up function is not used, WAKE should be connected to GND to avoid false wake-up. 33399 Analog Integrated Circuit Device Data Freescale Semiconductor 11 FUNCTIONAL DEVICE OPERATION OPERATIONAL MODES FUNCTIONAL DEVICE OPERATION OPERATIONAL MODES As described below and depicted in Figure 10 and Table 5 on page 13, the 33399 has two operational modes, normal and sleep, and one transitional mode, Awake. NORMAL MODE • LIN bus activity • Internal node wake-up (EN pin) • Wake-up from WAKE pin Figures 7, 8, and 9 on page 9 show device application circuit and detail of wake-up operations. This is the normal transmitting and receiving mode. All features are available. Wake-Up from LIN Bus (Awake Transitional Mode) SLEEP MODE In this mode the transmission path is disabled and the device is in low power mode. Supply current from VSUP is 20 µA typical. Wake-up can occur from LIN bus activity, as well as from node internal wake-up through the EN pin and the WAKE input pin. DEVICE POWER-UP (AWAKE TRANSITIONAL MODE) At system power-up (VSUP rises from zero), the 33399 automatically switches into the “Awake” mode (refer to Figure 10 below and Table 5 on page 13. It switches the INH pin in HIGH state to VSUP level. The microcontroller of the application then confirms the Normal mode by setting the EN pin HIGH. A wake-up from the LIN pin switching from recessive to dominant state (switch from VSUP to GND) can occur. This is achieved by a node sending a wake-up frame on the bus. This condition internally wakes up the interface, which switches the INH pin to a HIGH level to enable the voltage regulator. The device switches into the Awake mode. The microcontroller and the complete application power up. The microcontroller must switch the EN pin to a HIGH level to allow the device to leave the Awake mode and turn it into Normal mode in order to allow communication on the bus. Wake-Up from Internal Node Activity (Normal Mode) The application can internally wake up. In this case the microcontroller of the application sets the EN pin in the HIGH state. The device switches into Normal mode. Wake-Up from WAKE Pin (Awake Transitional Mode) DEVICE WAKE-UP EVENTS The device can be awakened from Sleep mode by three wake-up events: The application can wake up with the activation of an external switch. Refer to Table 1, 8-SOICN Pin Definitions on page 3. Power-Up/ Down VPWR < 7.0 V VPWR < 7.0 V VPWR > 7.0 V LIN Bus or WAKE Pin Wake-Up Sleep Awake VPWR < 7.0 V Normal 1.0 to 20 kbps EN HIGH EN HIGH (Local Wake-Up Event) EN LOW Note Refer to Table 5 for explanation. Figure 10. Operational and Transitional Modes State Diagram 33399 12 Analog Integrated Circuit Device Data Freescale Semiconductor FUNCTIONAL DEVICE OPERATION PROTECTION AND DIAGNOSIS FEATURES Table 5. Explanation of Operational and Transitional Modes State Diagram Operational/ Transitional Sleep Mode Awake Normal Mode LIN INH EN TXD Recessive state, driver off. 20 µA pullup current source. LOW LOW X High impedance. Recessive state, driver off. HIGH LOW X LOW. Driver active. 30 kΩ pullup active. HIGH HIGH LOW to drive LIN bus in dominant. HIGH to drive LIN bus in recessive. RXD Report LIN bus level: • LOW LIN bus dominant • HIGH LIN bus recessive X = Don’t care. PROTECTION AND DIAGNOSIS FEATURES ELECTROSTATIC DISCHARGE (ESD) The 33399 has two Human Body Model ESD values. All pins can handle ± 4.0 kV. The LIN bus pin, with respect to ground, can handle ± 5.0 kV. ELECTROMAGNETIC COMPATIBILITY RADIATED EMISSION ON LIN BUS OUTPUT LINE Radiated emission level on the LIN bus output line is internally limited and reduced by active slew rate control of the output bus driver. Figure 11 shows the results in the frequency range 100 kHz to 2.0 MHz. ELECTROMAGNETIC IMMUNITY (EMI) On the LIN bus pin, the 33399 offers high EMI level from external disturbance occurring at the LIN bus pin in order to guarantee communication during external disturbance. On the WAKE input pin, an internal filter is implemented to reduce false wake-up during external disturbance. NOISE FILTERING Noise filtering is used to protect the electronic module against illegal wake-up spikes on the bus. Integrated receiver filters suppress any high-frequency (HF) noise induced into the bus wires. The cut-off frequency of these filters is a compromise between propagation delay and HF suppression. Figure 11. Radiated Emission in Normal Mode 33399 Analog Integrated Circuit Device Data Freescale Semiconductor 13 TYPICAL APPLICATIONS TYPICAL APPLICATIONS The 33399 can be configured in several applications. Figures 12 and 13 show slave and master node applications. An additional pullup resistor of 1.0 kΩ in series with a diode must be added when the device is used in the master node. External Switch VPWR VREG Regulator INH 12V WAKE 33399 VSUP 5.0V Wake-Up Regulator Control INH VDD I/O EN MCU M Actuator Driver VREF Bias LIN Bus 5.0 V 30 kΩ Logic RXD Receiver LIN Protection SCI TXD Driver GND Figure 12. Slave Node Typical Application with WAKE Input Switch and INH (Switchable 5.0 V Regulator) 33399 14 Analog Integrated Circuit Device Data Freescale Semiconductor TYPICAL APPLICATIONS External Switch VPWR Master Node Pullup Regulator 5.0 V 12V WAKE 33399 1.0 kΩ VSUP Wake-Up Regulator Control INH 5.0 V VDD IRQ I/O I/O(2) EN M 30 kΩ Logic MCU RXD Actuator Driver VREF Bias LIN Bus 5.0V SCI Receiver LIN Protection TXD Driver GND Figure 13. Master Node Typical Device Application with MCU Wake-Up from Stop Mode (Non-Switchable 5.0 V Regulator, MCU Stop Mode) 33399 Analog Integrated Circuit Device Data Freescale Semiconductor 15 REFERENCE DOCUMENTS REFERENCE DOCUMENTS Table 6. Reference Documents Title Local Interconnect Network (LIN) Physical Interface: Difference Between MC33399 and MC33661 LIterature Order Number EB215 33399 16 Analog Integrated Circuit Device Data Freescale Semiconductor PACKAGING PACKAGE DIMENSIONS PACKAGING PACKAGE DIMENSIONS Important For the most current revision of the package, visit www.freescale.com and do a keyword search on the 98A drawing number below. D SUFFIX EF SUFFIX (Pb-FREE) 8-PIN SOIC NARROW BODY PLASTIC PACKAGE 98ASB42564B ISSUE U 33399 Analog Integrated Circuit Device Data Freescale Semiconductor 17 REVISION HISTORY REVISION HISTORY REVISION DATE 7.0 7/2006 8.0 10/2006 DESCRIPTION OF CHANGES • • • • • Implemented Revision History page Added Pb-Free suffix code EF Added EPP ordering part number MCZ33399EF/R2 Adjusted to the Freescale prevailing form and style Removed Peak Package Reflow Temperature During Reflow (solder reflow) parameter from MAXIMUM RATINGS on page 4. Added note with instructions to obtain this information from www.freescale.com. 33399 18 Analog Integrated Circuit Device Data Freescale Semiconductor How to Reach Us: Home Page: www.freescale.com Web Support: http://www.freescale.com/support USA/Europe or Locations Not Listed: Freescale Semiconductor, Inc. Technical Information Center, EL516 2100 East Elliot Road Tempe, Arizona 85284 +1-800-521-6274 or +1-480-768-2130 www.freescale.com/support Europe, Middle East, and Africa: Freescale Halbleiter Deutschland GmbH Technical Information Center Schatzbogen 7 81829 Muenchen, Germany +44 1296 380 456 (English) +46 8 52200080 (English) +49 89 92103 559 (German) +33 1 69 35 48 48 (French) www.freescale.com/support Japan: Freescale Semiconductor Japan Ltd. Headquarters ARCO Tower 15F 1-8-1, Shimo-Meguro, Meguro-ku, Tokyo 153-0064 Japan 0120 191014 or +81 3 5437 9125 [email protected] Asia/Pacific: Freescale Semiconductor Hong Kong Ltd. Technical Information Center 2 Dai King Street Tai Po Industrial Estate Tai Po, N.T., Hong Kong +800 2666 8080 [email protected] For Literature Requests Only: Freescale Semiconductor Literature Distribution Center P.O. Box 5405 Denver, Colorado 80217 1-800-441-2447 or 303-675-2140 Fax: 303-675-2150 [email protected] MC33399 Rev. 8.0 10/2006 RoHS-compliant and/or Pb-free versions of Freescale products have the functionality and electrical characteristics of their non-RoHS-compliant and/or non-Pb-free counterparts. For further information, see http://www.freescale.com or contact your Freescale sales representative. For information on Freescale’s Environmental Products program, go to http:// www.freescale.com/epp. Information in this document is provided solely to enable system and software implementers to use Freescale Semiconductor products. There are no express or implied copyright licenses granted hereunder to design or fabricate any integrated circuits or integrated circuits based on the information in this document. Freescale Semiconductor reserves the right to make changes without further notice to any products herein. Freescale Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Freescale Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters that may be provided in Freescale Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals”, must be validated for each customer application by customer’s technical experts. Freescale Semiconductor does not convey any license under its patent rights nor the rights of others. Freescale Semiconductor products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Freescale Semiconductor product could create a situation where personal injury or death may occur. Should Buyer purchase or use Freescale Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold Freescale Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Freescale Semiconductor was negligent regarding the design or manufacture of the part. Freescale™ and the Freescale logo are trademarks of Freescale Semiconductor, Inc. All other product or service names are the property of their respective owners. © Freescale Semiconductor, Inc., 2006. All rights reserved.