FREESCALE MC3363

Order this document by MC3363/D
The MC3363 is a single chip narrowband VHF FM radio receiver. It is a dual
conversion receiver with RF amplifier transistor, oscillators, mixers,
quadrature detector, meter drive/carrier detect and mute circuitry. The
MC3363 also has a buffered first local oscillator output for use with frequency
synthesizers, and a data slicing comparator for FSK detection.
• Wide Input Bandwidth – 200 MHz Using Internal Local Oscillator
Wide Input Bandwidth – 450 MHz Using External Local Oscillator
• RF Amplifier Transistor
•
•
•
•
•
•
•
•
•
LOW POWER
DUAL CONVERSION
FM RECEIVER
SEMICONDUCTOR
TECHNICAL DATA
Muting Operational Amplifier
Complete Dual Conversion
Low Voltage: VCC = 2.0 V to 6.0 Vdc
Low Drain Current: ICC = 3.6 mA (Typical) at VCC = 3.0 V,
Excluding RF Amplifier Transistor
Excellent Sensitivity: Input 0.3 µV (Typical) for 12 dB SINAD
Using Internal RF Amplifier Transistor
Data Shaping Comparator
DW SUFFIX
PLASTIC PACKAGE
CASE 751F
(SO-28L)
Received Signal Strength Indicator (RSSI) with 60 dB
Dynamic Range
Low Number of External Parts Required
Manufactured in Motorola′s MOSAIC Process Technology
ORDERING INFORMATION
Device
Operating
Temperature Range
Package
MC3363DW
TA = – 40 to +85°C
SO–28L
Figure 1. Pin Connections and Representative
Block Diagram
1
28
1st Mixer Input
Base
2
27
Varicap Control
Emitter
3
26
1st LO Tank
Collector
4
25
1st LO Tank
2nd LO Emitter
5
24
1st LO Output
2nd LO Base
6
23
1st Mixer Output
2nd Mixer Output
7
22
2nd Mixer Input
VCC
8
21
2nd Mixer Input
Limiter Input
9
20
VEE
Limiter Decoupling
10
19
Mute Output
Limiter Decoupling
11
18
Comparator Output
Meter Drive (RSSI)
12
17
Comparator Input
Carrier Detect
13
16
Recovered Audio
Quadrature Coil
14
15
Mute Input
–
+
1st Mixer Input
+
–
 Motorola, Inc. 1996
MOTOROLA ANALOG IC DEVICE DATA
Rev 0
1
MC3363
MAXIMUM RATINGS (TA = 25°C unless otherwise noted)
Rating
Pin
Symbol
Value
Unit
Power Supply Voltage
8
VCC(max)
7.0
Vdc
Operating Supply Voltage Range
(Recommended)
8
VCC
2.0 to 6.0
Vdc
Input Voltage (VCC = 5.0 Vdc)
1, 28
V1–28
1.0
Vrms
Mute Output Voltage
19
V19
– 0.7 to 8.0
Vpk
Junction Temperature
–
TJ
150
°C
Operating Ambient Temperature Range
–
TA
– 40 to + 85
°C
Storage Temperature Range
–
Tstg
– 65 to + 150
°C
ELECTRICAL CHARACTERISTICS (VCC = 5.0 Vdc, fo = 49.7 MHz, Deviation = ± 3.0 kHz, TA = 25°C, Mod 1.0 kHz,
test circuit of Figure 2 unless otherwise noted)
Characteristic
Pin
Min
Typ
Max
Units
8
–
4.5
8.0
mA
–3.0 dB Limiting Sensitivity (RF Amplifier Not Used)
–
0.7
2.0
µVrms
Input For 12 dB SINAD
–
0.3
–
20 dB S/N Sensitivity (RF Amplifier Not Used)
–
1.0
–
Drain Current (Carrier Detect Low)
1st Mixer Input Resistance (Parallel – Rp)
1, 28
–
690
–
Ω
1st Mixer Input Capacitance (Parallel – Cp)
1, 28
–
7.2
–
pF
1st Mixer Conversion Voltage Gain (Avc1, Open Circuit)
–
18
–
dB
2nd Mixer Conversion Voltage Gain )Avc2, Open Circuit)
–
21
–
µVrms
2nd Mixer Input Sensitivity (20 dB S/N) (10.7 MHz i/p)
21
–
10
–
Limiter Input Sensitivity (20 dB S/N) (455 kHz i/p)
9
–
100
–
RF Transistor DC Current Drain
4
1.0
1.5
2.5
mAdc
Noise Output Level (RF Signal = 0 mV)
16
–
70
–
mVrms
Recovered Audio (RF Signal Level = 1.0 mV)
16
120
200
–
mVrms
THD of Recovered Aduio (RF Signal = 1.0 mV)
16
–
2%
–
%
Detector Output Impedance
16
–
400
–
Ω
Series Equivalent Input Impedance
1
–
450–
j350
–
Data (Comparator)
(
p
) Output
p Voltage
g – High
g
D t (Comparator)
Data
(C
t ) Output
O t t Voltage
V lt
–L
Low
18
–
0.1
0
1
–
0.1
0
1
VCC
–
Vdc
Data (Comparator) Threshold Voltage Difference
17
70
110
150
mV
Meter Drive Slope
12
70
100
135
nA/dB
Carrier Detect Threshold (Below VCC)
12
0.53
0.64
0.77
Vdc
Mute Output Impedance – High
M te Output
O tp t Impedance – Lo
Mute
Low
19
–
–
10
25
–
–
MΩ
2
MOTOROLA ANALOG IC DEVICE DATA
1st Mixer Input
50 MHz
MOTOROLA ANALOG IC DEVICE DATA
LC1
0.1
0.1
CRF 2
68 k
10 k
1000 pF
10.245 M
120 pF
VCC = 5.0 Vdc
0.1
2.6
+
–
0.01
5.0 k
0.01
10 µ F
To PLL Phase Detector
10 k
15
14
17
5.0 k
0.01
Mute Input
Comparator Test Input
Recovered Audio
Output
Comparator Output
10 k
0.1
+
From PLL Phase Deetector
18
390 k
10 k
L1
LC1: Toko 7MC8128Z
L1: Coilcraft UNI 10/142 10–1/2 Turns
Mute Output
1.0 k
10.7 MHz
CRF 1
33 pF
L1 0.41 µ H
CRF 2: muRata CFU 455D
or Equivalent
CRF 1: muRata SFE 10.7 mA
or Equivalent
19
20
21
22
23
24
25
26
27
28
16
Carrier Detect Output
–
+
13
12
11
10
9
8
7
6
5
4
3
2
1
Ferronics 12–345–K Core
Figure 2. Test Circuit
MC3363
Figure 2.
3
MC3363
CIRCUIT DESCRIPTION
The MC3363 is a complete FM narrowband receiver from
RF amplifier to audio preamp output. The low voltage dual
conversion design yields low power drain, excellent
sensitivity and good image rejection in narrowband voice and
data link applications.
In the typical application, the input RF signal is amplified
by the RF transistor and then the first mixer amplifies the
signal and converts the RF input to 10.7 MHz. This IF signal
is filtered externally and fed into the second mixer, which
further amplifies the signal and converts it to a 455 kHz IF
signal. After external bandpass filtering, the low IF is fed into
the limiting amplifier and detection circuitry. The audio is
recovered using a conventional quadrature detector.
Twice-IF filtering is provided internally.
The input signal level is monitored by meter drive circuitry
which detects the amount of limiting in the limiting amplifier.
The voltage at the meter drive pin determines the state of the
carrier detect output, which is active low.
APPLICATIONS INFORMATION
The first local oscillator is designed to serve as the VCO in
a PLL frequency synthesized receiver. The MC3363 can
operate together with the MC145166/7 to provide a two-chip
ten–channel frequency synthesized receiver in the 46/49
cordless telephone band. The MC3363 can also be used with
the MC14515X series of CMOS PLL synthesizers and
MC120XX series of ECL prescalers in VHF frequency
synthesized applications to 200 MHz.
For single channel applications the first local oscillator can
be crystal controlled. The circuit of Figure 4 has been used
successfully up to 60 MHz. For higher frequencies an
external oscillator signal can be injected into Pins 25 and/or
26 — a level of approximately 100 mVrms is recommended.
The first mixer′s transfer characteristic is essentially flat to
450 MHz when this approach is used (keeping a constant
10.7 MHz IF frequency). The second local oscillator is a
Colpitts type which is typically run at 10.245 MHz under
crystal control.
The mixers are doubly balanced to reduce spurious
responses. The first and second mixers have conversion
gains of 18 dB and 21 dB (typical), respectively. Mixer gain is
stable with respect to supply voltage. For both conversions,
the mixer impedances and pin layout are designed to allow
the user to employ low cost, readily available ceramic filters.
Following the first mixer, a 10.7 MHz ceramic bandpass
filter is recommended. The 10.7 MHz filtered signal is then
fed into the second mixer input Pin 21, the other input Pin 22
being connected to VCC.
The 455 kHz IF is filtered by a ceramic narrow bandpass
filter then fed into the limiter input Pin 9. The limiter has 10 µV
sensitivity for – 3.0 dB limiting, flat to 1.0 MHz.
The output of the limiter is internally connected to the
quadrature detector, including a quadrature capacitor. A
parallel LC tank is needed externally from Pin 14 to VCC. A 68
kΩ shunt resistance is included which determines the peak
separation of the quadrature detector; a smaller value will
lower the Q and expand the deviation range and linearity, but
decrease recovered audio and sensitivity.
A data shaping circuit is available and can be coupled to
the recovered audio output of Pin 16. The circuit is a
comparator which is designed to detect zero crossings of
FSK modulation. Data rates of up to 35000 baud are
detectable using the comparator. Best sensitivity is obtained
when data rates are limited to 1200 baud maximum.
Hysteresis is available by connecting a high-valued resistor
from Pin 17 to Pin 18. Values below 120 kΩ are not
recommended as the input signal cannot overcome the
hysteresis.
The meter drive circuitry detects input signal level by
monitoring the limiting of the limiting amplifier stages.
Figure 5 shows the unloaded current at Pin 12 versus input
power. The meter drive current can used directly (RSSI) or
can be used to trip the carrier detect circuit at a specified
input power.
A muting op amp is provided and can be triggered by the
carrier detect output (Pin 13). This provides a carrier level
triggered squelch circuit which is activated when the RF input
at the desired input frequency falls below a present level. The
level at which this occurs is determined by the resistor placed
between the meter drive output (Pin 12) and VCC. Values
between 80 – 130 kΩ are recommended. This type of squelch
is pictured in Figures 3 and 4.
Hysteresis is available by connecting a high-valued
resistor Rh between Pins 12 and 13. The formula is:
Hyst = VCC / (Rh x 10 – 7) dB
The meter drive can also be used directly to drive a meter
or to provide AGC. A current to voltage converter or other
linear buffer will be needed for this application.
A second possible application of the op amp would be in a
noise triggered squelch circuit, similar to that used with the
MC3357/MC3359/MC3361B FM IFs. In this case the op amp
would serve as an active noise filter, the output of which
would be rectified and compared to a reference on a squelch
gate. The MC3363 does not have a dedicated squelch gate,
but the NPN RF input stage or data shaping comparator
might be used to provide this function if available. The op
amp is a basic type with the inverting input and the output
available. This application frees the meter drive to allow it to
be used as a linear signal strength monitor.
The circuit of Figure 4 is a complete 50 MHz receiver from
antenna input to audio preamp output. It uses few
components and has good performance. The receiver
operates on a single channel and has input sensitivity of
0.3 µV for 12 dB SINAD.
t
NOTE: For further application and design information, refer to AN980.
4
MOTOROLA ANALOG IC DEVICE DATA
RF Input
49.670 to
49.970 MHz
MOTOROLA ANALOG IC DEVICE DATA
Mute
Control
CF1
10.245 M
0.01
200 k
VCC = 5.0 Vdc
LC1
0.001
39 k
10 k
0.1
0.1
50 pF
L = 680 µ H
C = 180 pF
120 pF
120 pF
390
0.001
27 pF
10.5T
14
13
12
11
10
9
8
7
6
5
4
3
2
1
2.0T
T1 0.41 µ H
100 k
15
16
17
18
19
20
21
22
23
24
25
26
27
28
0.01
1.0 µ H
+
8.2 k
CRF 1
33 pF
10 k
0.41 µ H
+
0.01
10 µ H
0.1 µ F
20 k
+
Volume Control
10 µ F
Cr
Pin 24
Pin 25
Pin 26
Pin 27
f osc: 200 MHz
L = 0.08 µ H
Pull–Up
Resistor
3.3 k to 20 k
VCC (Regulated)
NOTE: Pull Up resistor is
used to run the oscillator above 50 MHz.
Recovered Audio
Output
Data Output
3.0 k
To
MC145166/7
Dual PLL
Frequency
Synchrsizer
From PLL Phase Detector
CRF 1: muRata SFE 10.7 mA or Equivalent
CRF 2: muRata CFU 455D or Equivalent
L1: Coilcraft UNI 10/142 10 1/2 Turns
LC1: Toko 7MC8128Z
Figure 3. Typical Application in a PLL Frequency Synthesized Receiver
MC3363
+
–
–
+
Figure 3.
5
6
10.01
21
22
23
50 k
139 k
10 k
F2
0.1
X1
1.0 k
LC1
0.1
1.0 k pF
1.0 k pF
Standard 10.7 MHz Filter
2.0–7.0 Vdc
Squelch
Adjust
VCC
0.22 µH
39 pF
VCC
9.1 M
0.1
F1
50 pF
120 pF
14
13
12
11
10
9
8
7
6
5
4
3
2
1
15 k
2N4402
100 k
MC3363DW
Carrier
Detect
Indicator
–
+
RLED
15
16
17
18
19
20
21
22
23
24
25
26
27
28
0.022
8.2 k
15 pF
5.0–25 pF
0.01
F2X
3.0 k
0.68 µH
0.68 µH
P1
100 k
3.3 µH
4.7 µH
0.1
0.01
X2
+
1.0 µF
0.1
1.0 µF
5.0 µF
10 k
1.0 k pF
10 µH
4.7 µH
20 k
300 Ω
20 k
4
3
2
1
50 k
MC34119D
L.O. Out
(optional)
5
6
7
8
100 µF
+
8.0 Ω Spkr
RLED is used to adjust LED current: I LED ≈
RLED
VCC – VLED
F1 – 455 kHz ceramic filter, R in = Rout = 1.5 kΩ to 2.0 k Ω
MuRata CFU455X or CFW455X, suffix denotes bandwidth
F2 – 10.7 MHz ceramic filter, R in = Rout = 330 Ω
MuRata SFE10.7MJ–A, SFA10.7MF5, or SFE10.7MS2A.
F2X – 10.7 MHz crystal filter, FOX 10M20A or equivalent.
Crystal filters improve adjacent channel and second
image (unwanted 48.76 MHz) rejection. Sensitivity is
degraded very slightly with this circuit.
LC1 – 455 kHz quadrature tank circuit; Toko 7MC8128Z
P1 – Volume control, miniature potentiometer, logarithmic
taper.
X11 – 10.245 MHz fundamental mode crystal, load capacity
32 pF.
X2 – 38.97 MHz, 3rd overtone crystal, series mode.
0.68 µ H adjustable coil; Coilcraft M1287–A
0.22 µ H adjustable coil; Coilcraft M1175–A
+
+
Figure 4. Single Channel Narrowband FM Receiver at 49.67 MHz
+
–
RF Input
49.67 MHz
50 Ω
MC3363
Figure 4.
MOTOROLA ANALOG IC DEVICE DATA
MOTOROLA ANALOG IC DEVICE DATA
11
9
2.0 k
10
2
Bias
4
3
1.0 k
25
26
27
Bias
Bias
1
24
1.0 k
1.0 k
28
12
100
14
23
8
5
6
Bias
Figure 5. Circuit Schematic
13
21
400
16
20
17
15
400
Bias
Bias
22
1.4 k
18
19
7
MC3363
Figure 5.
7
MC3363
Figure 6. PC Board Component View
with High Performance Crystal Filter
Figure 7. PC Board Circuit Side View
RF IN
Gnd
BNC
.1
.1
.001
3K
3.3
µH
10
µH
5–25P
.1
10K
20K
20K
4.7
µH
F2
X
15p
SM
.1
50K
4.7
µH
.1
1.0
100K
.022
8.2K
9,1M
10K
F1
MC3363DW
50p
SM
.68
µH
5 – 25P
1000p
.1
X2
Vcc
.01
µH
.01
1000p
120p
SM
1K
X1
.22
68 µ H
300
39p
SM
5.0
39K
51K
.1
15K
2N
4402
1.0
100
P1
LC1
50K
RLED
RL
100K
SPKR
MC3363DW
3.000 I
Vcc
RF IN
Gnd
Figure 8. PC Board Component Side Ground Plane
SPKR
MC3363DW
3.000I
8
MOTOROLA ANALOG IC DEVICE DATA
MC3363
OUTLINE DIMENSIONS
DW SUFFIX
PLASTIC PACKAGE
CASE 751F–04
(SO-28L)
ISSUE E
–A–
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION A AND B DO NOT INCLUDE
MOLD PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006)
PER SIDE.
5. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE
DAMBAR PROTRUSION SHALL BE 0.13
(0.005) TOTAL IN EXCESS OF D DIMENSION
AT MAXIMUM MATERIAL CONDITION.
15
28
14X
–B–
1
P
0.010 (0.25)
M
B
M
14
28X
D
0.010 (0.25)
M
T A
S
B
M
S
R
X 45 _
C
26X
–T–
G
SEATING
PLANE
K
F
DIM
A
B
C
D
F
G
J
K
M
P
R
MILLIMETERS
MIN
MAX
17.80
18.05
7.40
7.60
2.35
2.65
0.35
0.49
0.41
0.90
1.27 BSC
0.23
0.32
0.13
0.29
0_
8_
10.01
10.55
0.25
0.75
INCHES
MIN
MAX
0.701
0.711
0.292
0.299
0.093
0.104
0.014
0.019
0.016
0.035
0.050 BSC
0.009
0.013
0.005
0.011
0_
8_
0.395
0.415
0.010
0.029
J
MOTOROLA ANALOG IC DEVICE DATA
9
MC3363
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding
the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and
specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters which may be provided in Motorola
data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals”
must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of
others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other
applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury
or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola
and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees
arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that
Motorola was negligent regarding the design or manufacture of the part. Motorola and
are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal
Opportunity/Affirmative Action Employer.
Mfax is a trademark of Motorola, Inc.
How to reach us:
USA / EUROPE / Locations Not Listed: Motorola Literature Distribution;
P.O. Box 5405, Denver, Colorado 80217. 303–675–2140 or 1–800–441–2447
JAPAN: Nippon Motorola Ltd.: SPD, Strategic Planning Office, 4–32–1,
Nishi–Gotanda, Shinagawa–ku, Tokyo 141, Japan. 81–3–5487–8488
Mfax: [email protected] – TOUCHTONE 602–244–6609
ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park,
– US & Canada ONLY 1–800–774–1848 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298
INTERNET: http://motorola.com/sps
10
◊
MC3363/D
MOTOROLA ANALOG IC DEVICE
DATA