FREESCALE MC33910G5AC

MC33910G5AC/MC3433910G5AC
Freescale Semiconductor
Advance Information
Document Number: MC33910
Rev. 8.0, 3/2010
LIN System Basis Chip with High
Side Drivers
33910
The 33910G5/BAC is a Serial Peripheral Interface (SPI) controlled
System Basis Chip (SBC), combining many frequently used functions
in an MCU based system, plus a Local Interconnect Network (LIN)
transceiver. The 33910 has a 5.0 V, 50 mA/60 mA low dropout
regulator with full protection and reporting features. The device
provides full SPI readable diagnostics and a selectable timing
watchdog for detecting errant operation. The LIN Protocol Specification
2.0 and 2.1 compliant LIN transceiver has waveshaping circuitry that
can be disabled for higher data rates.
Two 50 mA/60 mA high side switches with optional pulse-width
modulated (PWM) are implemented to drive small loads. One high
voltage input is available for use in contact monitoring, or as external
wake-up input. This input can be used as high voltage Analog Input.
The voltage on this pin is divided by a selectable ratio and available via
an analog multiplexer.
The 33910 has three main operating modes: Normal (all functions
available), Sleep (VDD off, wake-up via LIN, wake-up inputs (L1), cyclic
sense and forced wake-up), and Stop (VDD on with limited current
capability, wake-up via CS, LIN bus, wake-up inputs, cyclic sense,
forced wake-up and external reset).
The 33910 is compatible with LIN Protocol Specification 2.0, 2.1, and
SAEJ2602-2.
SYSTEM BASIS CHIP WITH LIN
2ND GENERATION
AC SUFFIX (Pb-FREE)
98ASH70029A
32-PIN LQFP
ORDERING INFORMATION
Features
•
•
•
•
•
•
Full-duplex SPI interface at frequencies up to 4.0 MHz
LIN transceiver capable of up to 100 kbps with wave shaping
Two 50 mA/60 mA high side switches
One high voltage analog/logic Input
Configurable window watchdog
5.0 V low drop regulator with fault detection and low voltage reset
(LVR) circuitry
• Switched/protected 5.0 V output (used for Hall sensors)
• Pb-free packaging designated by suffix code AC
Device
Temperature
Range (TA)
MC33910G5AC/R2
- 40°C to 125°C
MC34910G5AC/R2
-40°C to 85°C
MC33910BAC/R2
- 40°C to 125°C
MC34910BAC/R2
-40°C to 85°C
* See Page 2 for Device Variations
33910
VBAT
VSENSE
HS1
VS1
VS2
L1
VDD
MCU
MOSI
MISO
SCLK
CS
RXD
TXD
IRQ
RST
LGND
PGND
AGND
PWMIN
ADOUT0
LIN
LIN INTERFACE
HVDD
HS2
WDCONF
Figure 1. 33910 Simplified Application Diagram
* This document contains certain information on a new product.
Specifications and information herein are subject to change without notice.
© Freescale Semiconductor, Inc., 2009 - 2010. All rights reserved.
Package
32-LQFP
MC33910G5AC/MC3433910G5AC
DEVICE VARIATIONS
DEVICE VARIATIONS
The 33910G5 data sheet is within MC33910G5 Product
Specifications Pages 3 to 46
The 33910BAC data sheet is within MC33911BAC
Product Specifications Pages 47 to 86
Table 1. This specification support the following products
Device
MC33910G5AC/R2
Temperature
- 40 to 125°C
Generation
2.5
Changes
1. Increase ESD GUN IEC61000-4-2 (gun test contact with 150 pF, 330 W
test conditions) performance to achieve ±6.0 kV min on the LIN pin.
2. Immunity against ISO7637 pulse 3b
3. Reduce EMC emission level on LIN
MC34910G5AC/R2
- 40 to 85°C
2.5
4. Improve EMC immunity against RF – target new specification including
3x68 pF
5. Comply with J2602 conformance test
MC33910BAC/R2
- 40 to 125°C
2.0
MC34910BAC/R2
- 40 to 85°C
2.0
Initial release
33910
2
Analog Integrated Circuit Device Data
Freescale Semiconductor
MC33910G5AC/MC3433910G5AC
MC33910G5 PRODUCT SPECIFICATIONS PAGES 3 TO 46
MC33910G5 PRODUCT SPECIFICATIONS
PAGES 3 TO 46
33910
Analog Integrated Circuit Device Data
Freescale Semiconductor
3
MC33910G5AC/MC3433910G5AC
INTERNAL BLOCK DIAGRAM
INTERNAL BLOCK DIAGRAM
RST IRQ
INTERRUPT CONTROL
MODULE
LVI, HVI,
ALL OT (VDD, HS, LIN, SD)
VS1
INTERNAL BUS
VS2
VDD
AGND
VOLTAGE REGULATOR
PGND
RESET CONTROL
MODULE
LVR, WD, EXT µC
5.0 V OUTPUT
MODULE
WINDOW
WATCHDOG
MODULE
HVDD
VS2
HIGH SIDE
CONTROL
MODULE
PWMIN
VS2
MISO
SCLK
HS2
SPI
&
CONTROL
ANALOG MULTIPLEXER
MOSI
CS
ADOUT0
WAKE-UP MODULE
RXD
TXD
HS1
VBAT
SENSE MODULE
VSENSE
CHIP TEMPERATURE
SENSE MODULE
ANALOG INPUT
MODULE
L1
DIGITAL INPUT MODULE
LIN PHYSICAL
LAYER
LIN
LGND
WDCONF
Figure 2. 33910 Simplified Internal Block Diagram
33910
4
Analog Integrated Circuit Device Data
Freescale Semiconductor
MC33910G5AC/MC3433910G5AC
PIN CONNECTIONS
AGND
VDD
HVDD
VSENSE
NC*
VS1
VS2
HS1
32
31
30
29
28
27
26
25
PIN CONNECTIONS
RXD
1
24
HS2
TXD
2
23
L1
MISO
3
22
NC*
MOSI
4
21
NC*
SCLK
5
20
NC*
CS
6
19
NC*
ADOUT0
7
18
PGND
PWMIN
8
17
NC*
9
10
11
12
13
14
15
16
RST
IRQ
NC*
WDCONF
LIN
LGND
NC*
NC*
* See Recommendation in Table below
Figure 3. 33910 Pin Connections
Table 2. 33910 Pin Definitions
A functional description of each pin can be found in the Functional Pin Description.
Pin
Pin Name
Formal Name
Definition
1
RXD
Receiver Output
This pin is the receiver output of the LIN interface which reports the state of
the bus voltage to the MCU interface.
2
TXD
Transmitter Input
This pin is the transmitter input of the LIN interface which controls the state of
the bus output.
3
MISO
SPI Output
SPI (Serial Peripheral Interface) data output. When CS is high, pin is in the
high-impedance state.
4
MOSI
SPI Input
SPI (Serial Peripheral Interface) data input.
5
SCLK
SPI Clock
SPI (Serial Peripheral Interface) clock Input.
6
CS
SPI Chip Select
7
ADOUT0
Analog Output Pin 0
8
PWMIN
PWM Input
9
RST
Internal Reset I/O
Bidirectional Reset I/O pin - driven low when any internal reset source is
asserted. RST is active low.
10
IRQ
Internal Interrupt
Output
Interrupt output pin, indicating wake-up events from Stop modemode or
events from Normal and Normal request modes. IRQ is active low.
11
NC
Not Connected
SPI (Serial Peripheral Interface) chip select input pin. CS is active low.
Analog Multiplexer Output.
High Side Pulse Width Modulation Input.
This pin must not be connected.
33910
Analog Integrated Circuit Device Data
Freescale Semiconductor
5
MC33910G5AC/MC3433910G5AC
PIN CONNECTIONS
Table 2. 33910 Pin Definitions
A functional description of each pin can be found in the Functional Pin Description.
Pin
Pin Name
Formal Name
Definition
12
WDCONF
Watchdog
Configuration Pin
13
LIN
LIN Bus
14
LGND
LIN Ground Pin
This pin is the device LIN ground connection. It is internally connected to the
PGND pin.
15, 16, 17, 19,
20, 21 & 22
NC
Not Connected
This pin must not be connected or connected to ground.
18
PGND
Power Ground Pin
23
L1
Wake-up Input
24
HS2
25
HS1
26
VS2
27
VS1
28
This input pin is for configuration of the watchdog period and allows the
disabling of the watchdog.
This pin represents the single-wire bus transmitter and receiver.
This pin is the device low side ground connection. It is internally connected to
the LGND pin.
This pin is the wake-up capable digital input(1). In addition, L1 input can be
sensed analog via the analog multiplexer.
High Side Outputs
High side switch outputs.
Power Supply Pin
These pins are device battery level power supply pins. VS2 is supplying the
HSx drivers while VS1 supplies the remaining blocks.(2)
NC
Not Connected
This pin can be left opening or connected to any potential ground or power
supply
29
VSENSE
Voltage Sense Pin
Battery voltage sense input.(3)
30
HVDD
Hall Sensor Supply
Output
+5.0 V switchable supply output pin.(4)
31
VDD
Voltage Regulator
Output
+5.0 V main voltage regulator output pin.(5)
32
AGND
Analog Ground Pin
This pin is the device analog ground connection.
Notes
1. When used as digital input, a series 33 kΩ resistor must be used to protect against automotive transients.
2. Reverse battery protection series diodes must be used externally to protect the internal circuitry.
3. This pin can be connected directly to the battery line for voltage measurements. The pin is self protected against reverse battery
connections. It is strongly recommended to connect a 10 kΩ resistor in series with this pin for protection purposes.
4. External capacitor (1.0 µF < C < 10 µF; 0.1 Ω < ESR < 5.0 Ω) required.
5. External capacitor (2.0 µF < C < 100 µF; 0.1 Ω < ESR < 10 Ω) required.
33910
6
Analog Integrated Circuit Device Data
Freescale Semiconductor
MC33910G5AC/MC3433910G5AC
ELECTRICAL CHARACTERISTICS
MAXIMUM RATINGS
ELECTRICAL CHARACTERISTICS
MAXIMUM RATINGS
Table 3. Maximum Ratings
All voltages are with respect to ground unless otherwise noted. Exceeding these ratings may cause a malfunction or
permanent damage to the device.
Ratings
Symbol
Value
Normal Operation (DC)
VSUP(SS)
-0.3 to 27
Transient Conditions (load dump)
VSUP(PK)
-0.3 to 40
VDD
-0.3 to 5.5
VIN
-0.3 to VDD +0.3
VIN(IRQ)
-0.3 to 11
VHS
- 0.3 to VSUP +0.3
Normal Operation with a series 33k resistor (DC)
VL1DC
-18 to 40
Transient input voltage with external component (according to ISO7637-2)
(See Figure )
VL1TR
±100
VVSENSE
-27 to 40
Normal Operation (DC)
VBUSDC
-18 to 40
Transient input voltage with external component (according to ISO7637-2)
(See Figure )
VBUSTR
-150 to 100
IVDD
Internally Limited
Unit
ELECTRICAL RATINGS
Supply Voltage at VS1 and VS2
Supply Voltage at VDD
Input / Output Pins Voltage
V
(6)
CS, RST, SCLK, PWMIN, ADOUT0, MOSI, MISO, TXD, RXD, HVDD
Interrupt Pin (IRQ)(7)
HS1 and HS2 Pin Voltage (DC)
V
L1 Pin Voltage
VSENSE Pin Voltage (DC)
V
V
LIN Pin Voltage
VDD Output Current
V
V
V
A
Notes
6. Exceeding voltage limits on specified pins may cause a malfunction or permanent damage to the device.
7. Extended voltage range for programming purpose only.
33910
Analog Integrated Circuit Device Data
Freescale Semiconductor
7
MC33910G5AC/MC3433910G5AC
ELECTRICAL CHARACTERISTICS
MAXIMUM RATINGS
Table 3. Maximum Ratings (continued)
All voltages are with respect to ground unless otherwise noted. Exceeding these ratings may cause a malfunction or
permanent damage to the device.
Ratings
Symbol
Value
ESD Capability
Unit
V
AECQ100
Human Body Model - JESD22/A114 (CZAP = 100 pF, RZAP = 1500 Ω)
± 8.0k
LIN Pin
VESD1-1
L1
VESD1-2
± 6.0k
all other Pins
VESD1-3
±2000
Corner Pins (Pins 1, 8, 9, 16, 17, 24, 25 and 32)
VESD2-1
± 750
All other Pins (Pins 2-7, 10-15, 18-23, 26-31)
VESD2-2
± 500
LIN pin with 220 pF
VESD3-1
± 20k
LIN pin without capacitor
VESD3-2
± 11k
VS1/VS2 (100 nF to ground)
VESD3-3
>± 12k
L1 input (33 kΩ serial resistor)
VESD3-4
±6000
LIN pin with 220 pF and without capacitor
VESD4-1
± 8000
VS1/VS2 (100 nF to ground)
VESD4-2
± 8000
VESD4-3
± 8000
Charge Device Model - JESD22/C101 (CZAP = 4.0 pF)
According to LIN Conformance Test Specification / LIN EMC Test
Specification, August 2004 (CZAP = 150 pF, RZAP = 330 Ω)
Contact Discharge, Unpowered
According to IEC 61000-4-2 (CZAP = 150 pF, RZAP = 330 Ω)
Unpowered
L1 input (33 kΩ serial resistor)
THERMAL RATINGS
Operating Ambient Temperature (8)
Operating Junction Temperature
°C
TA
33910
-40 to 125
34910
-40 to 85
TJ
-40 to 150
°C
Storage Temperature
TSTG
-55 to 150
°C
Thermal Resistance, Junction to Ambient
RθJA
Natural Convection, Single Layer board (1s)(8), (9)
Natural Convection, Four Layer board (2s2p)(8), (10)
Thermal Resistance, Junction to Case(11)
Peak Package Reflow Temperature During Reflow(12), (13)
°C/W
85
56
RθJC
23
°C/W
TPPRT
Note 13
°C
Notes
8.
Junction temperature is a function of on-chip power dissipation, package thermal resistance, mounting site (board) temperature, ambient
temperature, air flow, power dissipation of other components on the board, and board thermal resistance.
9.
10.
11.
12.
Per JEDEC JESD51-2 with the single layer board (JESD51-3) horizontal.
Per JEDEC JESD51-6 with the board (JESD51-7) horizontal.
Thermal resistance between the die and the case top surface as measured by the cold plate method (MIL SPEC-883 Method 1012.1).
Pin soldering temperature limit is for 10 seconds maximum duration. Not designed for immersion soldering. Exceeding these limits may
cause malfunction or permanent damage to the device.
Freescale’s Package Reflow capability meets Pb-free requirements for JEDEC standard J-STD-020C. For Peak Package Reflow
Temperature and Moisture Sensitivity Levels (MSL), go to www.freescale.com, search by part number [e.g. remove prefixes/suffixes and
enter the core ID to view all orderable parts. (i.e. MC33xxxD enter 33xxx), and review parametrics.
13.
33910
8
Analog Integrated Circuit Device Data
Freescale Semiconductor
MC33910G5AC/MC3433910G5AC
ELECTRICAL CHARACTERISTICS
STATIC ELECTRICAL CHARACTERISTICS
STATIC ELECTRICAL CHARACTERISTICS
Table 4. Static Electrical Characteristics
Characteristics noted under conditions 5.5 V ≤ VSUP ≤ 18 V, -40°C ≤ TA ≤ 125°C for the 33910 and -40°C ≤ TA ≤ 85°C for the
34910, unless otherwise noted. Typical values noted reflect the approximate parameter mean at TA = 25°C under nominal
conditions, unless otherwise noted.
Characteristic
Symbol
Min
Typ
Max
Unit
VSUP
5.5
–
18
V
Functional Operating Voltage(14)
VSUPOP
–
–
27
V
Load Dump
VSUPLD
–
–
40
V
IRUN
–
4.5
10
mA
SUPPLY VOLTAGE RANGE (VS1, VS2)
Nominal Operating Voltage
SUPPLY CURRENT RANGE (VSUP = 13.5 V)
Normal Mode (IOUT at VDD = 10 mA), LIN Recessive State(15)
Stop Mode, VDD ON with IOUT = 100 µA, LIN Recessive State
(17) (18)
,
(15), (16),
ISTOP
µA
5.5 V < VSUP < 12 V
–
47
VSUP = 13.5 V
–
62
90
13.5 V < VSUP < 18 V
–
180
400
5.5 V < VSUP < 12 V
–
27
35
VSUP = 13.5 V
–
33
48
13.5 V ≤ VSUP < 18 V
–
160
300
ICYCLIC
–
10
–
Threshold (measured on VS1)(19)
VBATFAIL
1.5
3.0
3.9
Hysteresis (measured on VS1)(19)
VBATFAIL_HYS
–
0.9
–
VSUV
5.55
6.0
6.6
VSUV_HYS
–
0.2
–
VSOV
18
19.25
20.5
–
1.0
–
Sleep Mode, VDD OFF, LIN Recessive State(15), (17)
Cyclic Sense Supply Current Adder(19)
80
ISLEEP
µA
µA
SUPPLY UNDER/OVER-VOLTAGE DETECTIONS
Power-On Reset (BATFAIL)(20)
V
VSUP under-voltage detection (VSUV Flag) (Normal and Normal Request
Modes, Interrupt Generated)
Threshold (measured on VS1)
Hysteresis (measured on VS1)
V
VSUP over-voltage detection (VSOV Flag) (Normal and Normal Request
Modes, Interrupt Generated)
Threshold (measured on VS1)
Hysteresis (measured on VS1)
VSOV_HYS
V
Notes
14. Device is fully functional. All features are operating.
15. Total current (IVS1 + IVS2) measured at GND pins excluding all loads, cyclic sense disabled.
16.
Total IDD current (including loads) below 100 µA.
17.
Stop and Sleep modes current will increase if VSUP exceeds13.5 V.
18.
19.
20.
This parameter is guaranteed after 90 ms.
This parameter is guaranteed by process monitoring but not production tested.
The Flag is set during power up sequence. To clear the flag, a SPI read must be performed.
33910
Analog Integrated Circuit Device Data
Freescale Semiconductor
9
MC33910G5AC/MC3433910G5AC
ELECTRICAL CHARACTERISTICS
STATIC ELECTRICAL CHARACTERISTICS
Table 4. Static Electrical Characteristics (continued)
Characteristics noted under conditions 5.5 V ≤ VSUP ≤ 18 V, -40°C ≤ TA ≤ 125°C for the 33910 and -40°C ≤ TA ≤ 85°C for the
34910, unless otherwise noted. Typical values noted reflect the approximate parameter mean at TA = 25°C under nominal
conditions, unless otherwise noted.
Characteristic
(21)
VOLTAGE REGULATOR
Symbol
Min
Typ
Max
4.75
5.00
5.25
60
110
200
–
0.1
0.25
Unit
(VDD)
Normal Mode Output Voltage
VDDRUN
1.0 mA < IVDD < 50 mA; 5.5 V < VSUP < 27 V
Normal Mode Output Current Limitation
IVDDRUN
Dropout Voltage(22)
VDDDROP
IVDD = 50 mA
Stop Mode Output Voltage
V
V
VDDSTOP
IVDD < 5.0 mA
mA
V
4.75
5.0
5.25
IVDDSTOP
6.0
13
36
Normal mode, 5.5 V < VSUP < 18 V; IVDD = 10 mA
LRRUN
–
–
25
Stop mode, 5.5 V < VSUP < 18 V; IVDD = 1.0 mA
LRSTOP
–
–
25
Normal mode, 1.0 mA < IVDD < 50 mA
LDRUN
–
–
80
Stop mode, 0.1 mA < IVDD < 5.0 mA
LDSTOP
–
–
50
90
115
140
TPRE_HYS
–
13
–
°C
TSD
150
170
190
°C
TSD_HYS
–
13
–
°C
-2.0
–
2.0
20
35
50
Stop Mode Output Current Limitation
Line Regulation
mV
Load Regulation
Over-temperature Prewarning
mA
mV
(Junction)(23)
TPRE
Interrupt generated, VDDOT Bit Set
Over-temperature Prewarning Hysteresis(23)
Over-temperature Shutdown Temperature
(Junction)(23)
(23)
Over-temperature Shutdown Hysteresis
°C
HALL SENSOR SUPPLY OUTPUT(24) (HVDD)
VDD Voltage matching HVDDACC = (HVDD-VDD) / VDD * 100%
HVDDACC
IHVDD = 15 mA
Current Limitation
Dropout Voltage
IHVDD
HVDDDROP
IHVDD = 15 mA; IVDD = 5.0 mA
Line Regulation
–
160
300
–
–
40
mV
LDHVDD
1.0 mA > IHVDD > 15 mA; IVDD = 5.0 mA
mA
mV
LRHVDD
IHVDD = 5.0 mA; IVDD = 5.0 mA
Load Regulation
%
mV
–
–
20
Notes
21. Specification with external capacitor 2.0 µF < C < 100 µF and 100 mΩ ≤ ESR ≤ 10 Ω.
22. Measured when voltage has dropped 250 mV below its nominal Value (5.0 V).
23. This parameter is guaranteed by process monitoring but not production tested.
24. Specification with external capacitor 1.0 µF < C < 10 µF and 100 mΩ ≤ ESR ≤ 10 Ω.
33910
10
Analog Integrated Circuit Device Data
Freescale Semiconductor
MC33910G5AC/MC3433910G5AC
ELECTRICAL CHARACTERISTICS
STATIC ELECTRICAL CHARACTERISTICS
Table 4. Static Electrical Characteristics (continued)
Characteristics noted under conditions 5.5 V ≤ VSUP ≤ 18 V, -40°C ≤ TA ≤ 125°C for the 33910 and -40°C ≤ TA ≤ 85°C for the
34910, unless otherwise noted. Typical values noted reflect the approximate parameter mean at TA = 25°C under nominal
conditions, unless otherwise noted.
Characteristic
Symbol
Min
Typ
Max
Unit
VRSTTH
4.3
4.5
4.7
V
0.0
–
0.9
-150
-250
-350
1.5
–
8.0
RST INPUT/OUTPUT PIN (RST)
VDD Low Voltage Reset Threshold
Low-state Output Voltage
VOL
IOUT = 1.5 mA; 3.5 V ≤ VSUP ≤ 27 V
High-state Output Current (0 V < VOUT < 3.5 V)
IOH
Pull-down Current Limitation (internally limited)
IPD_MAX
VOUT = VDD
V
µA
mA
Low-state Input Voltage
VIL
-0.3
–
0.3 x VDD
V
High-state Input Voltage
VIH
0.7 x VDD
–
VDD +0.3
V
MISO SPI OUTPUT PIN (MISO)
Low-state Output Voltage
VOL
IOUT = 1.5 mA
High-state Output Voltage
0.0
–
1.0
VDD -0.9
–
VDD
-10
–
10
VOH
IOUT = -250 µA
Tri-state Leakage Current
V
V
ITRIMISO
0 V ≤ VMISO ≤ VDD
µA
SPI INPUT PINS (MOSI, SCLK, CS)
Low-state Input Voltage
VIL
-0.3
–
0.3 x VDD
V
High-state Input Voltage
VIH
0.7 x VDD
–
VDD +0.3
V
MOSI, SCLK Input Current
IIN
-10
–
10
10
20
30
0 V ≤ VIN ≤ VDD
CS Pull-up Current
µA
IPUCS
0 V < VIN < 3.5 V
µA
INTERRUPT OUTPUT PIN (IRQ)
Low-state Output Voltage
VOL
IOUT = 1.5 mA
High-state Output Voltage
0.0
–
0.8
VDD -0.8
–
VDD
–
–
2.0
VOH
IOUT = -250 µA
Leakage Current
V
V
IOUT
VDD ≤ VOUT ≤ 10 V
mA
PULSE WIDTH MODULATION INPUT PIN (PWMIN)
Low-state Input Voltage
VIL
-0.3
–
0.3 x VDD
V
High-state Input Voltage
VIH
0.7 x VDD
–
VDD +0.3
V
Pull-up current
0 V < VIN < 3.5 V
IPUPWMIN
µA
10
20
30
33910
Analog Integrated Circuit Device Data
Freescale Semiconductor
11
MC33910G5AC/MC3433910G5AC
ELECTRICAL CHARACTERISTICS
STATIC ELECTRICAL CHARACTERISTICS
Table 4. Static Electrical Characteristics (continued)
Characteristics noted under conditions 5.5 V ≤ VSUP ≤ 18 V, -40°C ≤ TA ≤ 125°C for the 33910 and -40°C ≤ TA ≤ 85°C for the
34910, unless otherwise noted. Typical values noted reflect the approximate parameter mean at TA = 25°C under nominal
conditions, unless otherwise noted.
Characteristic
Symbol
Min
Typ
Max
TJ = 25°C, ILOAD = 50 mA; VSUP > 9.0 V
–
–
7.0
TJ = 150°C, ILOAD = 50 mA; VSUP > 9.0 V(25)
–
–
10
TJ = 150°C, ILOAD = 30 mA; 5.5 V < VSUP < 9.0 V(25)
–
–
14
60
90
250
–
5.0
7.5
–
–
10
Unit
HIGH SIDE OUTPUTS HS1 AND HS2 PINS (HS1, HS2)
Output Drain-to-Source On Resistance
Output Current Limitation(26)
ILIMHSX
0 V < VOUT < VSUP - 2.0 V
Open Load Current Detection(27)
Leakage Current
IOLHSX
mA
ILEAK
-0.2 V < VHSX < VS2 + 0.2 V
Short-circuit Detection Threshold(28)
Shutdown(29), (30)
Over-temperature Shutdown
Hysteresis(30)
mA
µA
VTHSC
5.5 V < VSUP < 27 V
Over-temperature
Ω
RDS(ON)
V
VSUP -2.0
–
–
THSSD
140
160
180
°C
THSSD_HYS
–
10
–
°C
2.0
2.5
3.0
3.0
3.5
4.0
L1 INPUT PIN (L1)
Low Detection Threshold(31)
VTHL
5.5 V < VSUP < 27 V
High Detection Threshold(31)
VTHH
5.5 V < VSUP < 27 V
Hysteresis(31)
V
V
VHYS
5.5 V < VSUP < 27 V
V
0.4
0.8
1.4
-10
–
10
800
1300
2000
L1DS (L1 Divider Select) = 0
0.95
1.0
1.05
L1DS (L1 Divider Select) = 1
3.42
3.6
3.78
-80
6.0
80
-22
2.0
22
L1DS (L1 Divider Select) = 0
96
100
104
L1DS (L1 Divider Select) = 1
96
100
104
Input
Current(32)
IIN
-0.2 V < VIN < VS1
Analog Input Impedance(33)
Analog Input Divider Ratio (RATIOL1 = VL1 / VADOUT0)
Analog Output offset Ratio
L1DS (L1 Divider Select) = 0
RL1IN
kΩ
RATIOL1
VRATIOL1OFFSET
L1DS (L1 Divider Select) = 1
Analog Inputs Matching
µA
mV
L1MATCHING
%
Notes
25. This parameter is production tested up to TA = 125°C, and guaranteed by process monitoring up to TJ = 150°C.
26.
27.
28.
29.
30.
31.
32.
33.
When over-current occurs, the corresponding high side stays ON with limited current capability and the HSxCL flag is set in the HSSR.
When open load occurs, the flag (HSxOP) is set in the HSSR.
HS automatically shutdown if HSOT occurs or if the HVSE flag is enabled and an over-voltage occurs.
When over-temperature shutdown occurs, both high sides are turned off. All flags in HSSR are set.
Guaranteed by characterization but not production tested
If L1 pin is unused it must be connected to ground.
Analog multiplexer input disconnected from L1 input pin.
Analog multiplexer input connected to L1 input pin.
33910
12
Analog Integrated Circuit Device Data
Freescale Semiconductor
MC33910G5AC/MC3433910G5AC
ELECTRICAL CHARACTERISTICS
STATIC ELECTRICAL CHARACTERISTICS
Table 4. Static Electrical Characteristics (continued)
Characteristics noted under conditions 5.5 V ≤ VSUP ≤ 18 V, -40°C ≤ TA ≤ 125°C for the 33910 and -40°C ≤ TA ≤ 85°C for the
34910, unless otherwise noted. Typical values noted reflect the approximate parameter mean at TA = 25°C under nominal
conditions, unless otherwise noted.
Characteristic
Symbol
Min
Typ
Max
Unit
REXT
20
–
200
kΩ
WDACC
-15
–
15
%
TA = -40°C
2.0
-
2.8
TA = 25°C
2.8
3.0
3.6
TA = 125°C
3.6
WINDOW WATCHDOG CONFIGURATION PIN (WDCONF)
(34)
External Resistor Range
Watchdog Period Accuracy with External Resistor (Excluding Resistor
Accuracy)(35)
ANALOG MULTIPLEXER
Temperature Sense Analog Output Voltage
Temperature Sense Analog Output Voltage per characterization
VADOUT0_TEMP
(36)
V
4.6
VADOUT0_25
3.1
3.15
3.2
V
STTOV
9.0
10.5
12
mV/K
STTOV_3T
9.9
10.2
10.5
mV/K
5.0
5.25
5.5
5.15
5.25
5.35
TA = 25°C
Internal Chip Temperature Sense Gain
Internal Chip Temperature Sense Gain per characterization at 3
temperatures(36) See Figure 16, Temperature Sense Gain
VSENSE Input Divider Ratio (RATIOVSENSE = VVSENSE / VADOUT0)
RATIOVSENSE
5.5 V < VSUP < 27 V
VSENSE Input Divider Ratio (RATIOVSENSE=Vsense/Vadout0) per
characterization(36)
RATIOVSENSECZ
5.5 <Vsup< 27 V
VSENSE Output Related Offset
VSENSE Output Related Offset per characterization(36)
OFFSETVSENSE
mV
-30
-10
30
-30
-12.6
0
VDD -0.35
–
VDD
0.0
–
0.35
0.0
–
0.8
VDD -0.8
–
VDD
OFFSETVSENSE
_CZ
mV
ANALOG OUTPUT (ADOUT0)
Maximum Output Voltage
VOUT_MAX
-5.0 mA < IO < 5.0 mA
Minimum Output Voltage
V
VOUT_MIN
-5.0 mA < IO < 5.0 mA
V
RXD OUTPUT PIN (LIN PHYSICAL LAYER) (RXD)
Low-state Output Voltage
VOL
IOUT = 1.5 mA
High-state Output Voltage
IOUT = -250 µA
VOH
V
V
Notes
34. For VSUP 4.7 to 18 V
35.
Watchdog timing period calculation formula: tPWD [ms] = [0.466 * (REXT - 20)] + 10 with (REXT in kΩ)
36.
These limits have been defined after laboratory characterization on 3 lots and 30 samples. These tighten limits could not be guaranteed
by production test.
33910
Analog Integrated Circuit Device Data
Freescale Semiconductor
13
MC33910G5AC/MC3433910G5AC
ELECTRICAL CHARACTERISTICS
STATIC ELECTRICAL CHARACTERISTICS
Table 4. Static Electrical Characteristics (continued)
Characteristics noted under conditions 5.5 V ≤ VSUP ≤ 18 V, -40°C ≤ TA ≤ 125°C for the 33910 and -40°C ≤ TA ≤ 85°C for the
34910, unless otherwise noted. Typical values noted reflect the approximate parameter mean at TA = 25°C under nominal
conditions, unless otherwise noted.
Characteristic
Symbol
Min
Typ
Max
Unit
Low-state Input Voltage
VIL
-0.3
–
0.3 x VDD
V
High-state Input Voltage
VIH
0.7 x VDD
–
VDD +0.3
V
IPUIN
10
20
30
µA
TXD INPUT PIN (LIN PHYSICAL LAYER) (TXD)
Pin Pull-up Current, 0 V < VIN < 3.5 V
LIN PHYSICAL LAYER WITH J2602 FEATURE ENABLED (BIT DIS_J2602 = 0)
LIN Under Voltage threshold
VTH_UNDER_
Positive and Negative threshold (VTHP, VTHN)
VOLTAGE
Hysteresis (VTHP - VTHN)
LIN PHYSICAL LAYER, TRANSCEIVER
V
5.0
6.0
VJ2602_DEG
400
mV
(LIN)(37)
Operating Voltage Range
VBAT
8.0
18
V
Supply Voltage Range
VSUP
7.0
18
V
VSUP_NON_OP
-0.3
40
V
Voltage Range within which the device is not destroyed
Current Limitation for Driver Dominant State
IBUS_LIM
Driver ON, VBUS = 18 V
Input Leakage Current at the receiver
Leakage Output Current to GND
Control unit disconnected from ground(38)
Receiver Threshold Center
V(39)
-1.0
–
–
–
–
20
mA
-1.0
–
1.0
–
–
100
–
–
0.4
µA
VBUSDOM
VSUP
VBUSREC
VSUP
0.6
–
–
0.475
0.5
0.525
VBUS_CNT
VSUP
VHYS
(VTH_REC - VTH_DOM)
mA
µA
IBUSNO_BAT
(VTH_DOM + VTH_REC)/2
Receiver Threshold Hysteresis
200
IBUS_NO_GND
GNDDEVICE = VSUP; VBAT = 12 V; 0 < VBUS < 18 V
Receiver Recessive State
90
IBUS_PAS_REC
Driver Off; 8.0 V < VBAT < 18 V; 8.0 V < VBUS < 18 V; VBUS ≥ VBAT
Receiver Dominant State
40
IBUS_PAS_DOM
Driver off; VBUS = 0 V; VBAT = 12 V
VBAT Disconnected; VSUP_DEVICE = GND; 0 V < VBUS < 18
mA
VSUP
–
–
0.175
Voltage Drop at the serial Diode in pull-up path
VSERDIODE
0.4
1.0
V
VBAT_SHIFT
VSHIFT_BAT
0
11.5%
VBAT
GND_SHIFT
VSHIFT_GND
0
11.5%
VBAT
Notes
37. Parameters guaranteed for 7.0 V ≤ VSUP ≤ 18 V.
38.
39.
Loss of local ground must not affect communication in the residual network.
Node has to sustain the current that can flow under this condition. Bus must remain operational under this condition.
33910
14
Analog Integrated Circuit Device Data
Freescale Semiconductor
MC33910G5AC/MC3433910G5AC
ELECTRICAL CHARACTERISTICS
STATIC ELECTRICAL CHARACTERISTICS
Table 4. Static Electrical Characteristics (continued)
Characteristics noted under conditions 5.5 V ≤ VSUP ≤ 18 V, -40°C ≤ TA ≤ 125°C for the 33910 and -40°C ≤ TA ≤ 85°C for the
34910, unless otherwise noted. Typical values noted reflect the approximate parameter mean at TA = 25°C under nominal
conditions, unless otherwise noted.
Characteristic
LIN PHYSICAL LAYER, TRANSCEIVER (LIN) (CONTINUED)
Symbol
Min
Typ
Max
Unit
5.3
5.8
V
(37)
LIN Wake-up threshold from Stop or Sleep Mode(40)
VBUSWU
LIN Pull-up Resistor to VSUP
RSLAVE
20
30
60
kΩ
TLINSD
140
160
180
°C
TLINSD_HYS
–
10
–
°C
Over-temperature Shutdown
(41)
Over-temperature Shutdown Hysteresis
Notes
40. This parameter is 100% tested on an Automatic Tester. However, since it has not been monitored during reliability stresses, Freescale
does not guarantee this parameter during the product's life time.
41. When over-temperature shutdown occurs, the LIN bus goes in recessive state and the flag LINOT in LINSR is set.
33910
Analog Integrated Circuit Device Data
Freescale Semiconductor
15
MC33910G5AC/MC3433910G5AC
ELECTRICAL CHARACTERISTICS
DYNAMIC ELECTRICAL CHARACTERISTICS
DYNAMIC ELECTRICAL CHARACTERISTICS
Table 5. Dynamic Electrical Characteristics
Characteristics noted under conditions 5.5 V ≤ VSUP ≤ 18 V, -40°C ≤ TA ≤ 125°C for the 33910 and -40°C ≤ TA ≤ 85°C for the
34910, unless otherwise noted. Typical values noted reflect the approximate parameter mean at TA = 25°C under nominal
conditions, unless otherwise noted.
Characteristic
Symbol
Min
Typ
Max
Unit
SPI Operating Frequency
f SPIOP
–
–
4.0
MHz
SCLK Clock Period
SPI INTERFACE TIMING (SEE Figure 13)
tPSCLK
250
–
N/A
ns
SCLK Clock High Time(42)
tWSCLKH
110
–
N/A
ns
SCLK Clock Low Time(42)
tWSCLKL
110
–
N/A
ns
Falling Edge of CS to Rising Edge of SCLK(42)
tLEAD
100
–
N/A
ns
Falling Edge of SCLK to CS Rising Edge(42)
tLAG
100
–
N/A
ns
MOSI to Falling Edge of SCLK(42)
tSISU
40
–
N/A
ns
Falling Edge of SCLK to MOSI(42)
tSIH
40
–
N/A
ns
MISO Rise Time(42)
tRSO
–
40
–
CL = 220 pF
MISO Fall Time(42)
tFSO
CL = 220 pF
Time from Falling or Rising Edges of
ns
ns
–
40
–
CS to:(42)
ns
- MISO Low-impedance
tSOEN
0.0
–
50
- MISO High-impedance
tSODIS
0.0
–
50
Time from Rising Edge of SCLK to MISO Data Valid(42)
tVALID
0.0
–
75
t RST
0.65
1.0
1.35
ms
t RSTDF
350
480
900
ns
8.5
10
11.5
0.2 x VDD ≤ MISO ≥ 0.8 x VDD, CL = 100 pF
ns
RST OUTPUT PIN
Reset Low-level Duration After VDD High (see Figure 12)
Reset Deglitch Filter Time
WINDOW WATCHDOG CONFIGURATION PIN (WDCONF)
Watchdog Time Period(43)
External Resistor REXT = 20 kΩ (1%)
t PWD
ms
External Resistor REXT = 200 kΩ (1%)
79
94
108
Without External Resistor REXT (WDCONF Pin Open)
110
150
205
Notes
42. This parameter is guaranteed by process monitoring but not production tested.
43. Watchdog timing period calculation formula: tPWD [ms] = [0.466 * (REXT - 20)] + 10 with (REXT in kΩ)
33910
16
Analog Integrated Circuit Device Data
Freescale Semiconductor
MC33910G5AC/MC3433910G5AC
ELECTRICAL CHARACTERISTICS
DYNAMIC ELECTRICAL CHARACTERISTICS
Table 5. Dynamic Electrical Characteristics (continued)
Characteristics noted under conditions 5.5 V ≤ VSUP ≤ 18 V, -40°C ≤ TA ≤ 125°C for the 33910 and -40°C ≤ TA ≤ 85°C for the
34910, unless otherwise noted. Typical values noted reflect the approximate parameter mean at TA = 25°C under nominal
conditions, unless otherwise noted.
Characteristic
Symbol
Min
Typ
Max
Unit
t WUF
8.0
20
38
μs
–
–
5.0
t NR TOUT
110
150
205
ms
TON
130
200
270
µs
+35
%
L1 INPUT
L1 Filter Time Deglitcher(44)
STATE MACHINE TIMING
Delay Between CS LOW-to-HIGH Transition (at End of SPI Stop Command)
and Stop Mode Activation(44)
Normal Request Mode Timeout (see Figure 12)
Cyclic Sense ON Time from Stop and Sleep Mode(45)
t STOP
Cyclic Sense Accuracy(44)
Delay Between SPI Command and HS Turn On(46)
-35
–
–
10
μs
t S-OFF
9.0 V < VSUP < 27 V
Delay Between Normal Request and Normal Mode After a Watchdog Trigger
Command (Normal Request Mode)(44)
μs
t S-ON
9.0 V < VSUP < 27 V
Delay Between SPI Command and HS Turn Off(46)
μs
–
–
10
–
–
10
μs
t SNR2N
Delay Between CS Wake-up (CS LOW to HIGH) in Stop Mode and:
μs
Normal Request mode, VDD ON and RST HIGH
t WUCS
9.0
15
80
First Accepted SPI Command
t WUSPI
90
—
N/A
t 2CS
4.0
—
—
35
50
70
Minimum Time Between Rising and Falling Edge on the CS
μs
J2602 DEGLITCHER
VSUP Deglitcher(47)
(DIS_J2602 = 0)
tJ2602_DEG
μs
Notes
44. This parameter is guaranteed by process monitoring but not production tested.
45. This parameter is 100% tested on an Automatic Tester. However, since it has not been monitored during reliability stresses, Freescale
does not guarantee this parameter during the product's life time.
46. Delay between turn on or off command (rising edge on CS) and HS ON or OFF, excluding rise or fall time due to external load.
47. This parameter has not been monitoring during operating life test.
33910
Analog Integrated Circuit Device Data
Freescale Semiconductor
17
MC33910G5AC/MC3433910G5AC
ELECTRICAL CHARACTERISTICS
DYNAMIC ELECTRICAL CHARACTERISTICS
Table 5. Dynamic Electrical Characteristics (continued)
Characteristics noted under conditions 5.5 V ≤ VSUP ≤ 18 V, -40°C ≤ TA ≤ 125°C for the 33910 and -40°C ≤ TA ≤ 85°C for the
34910, unless otherwise noted. Typical values noted reflect the approximate parameter mean at TA = 25°C under nominal
conditions, unless otherwise noted.
Characteristic
Symbol
Min
Typ
Max
Unit
LIN PHYSICAL LAYER: DRIVER CHARACTERISTICS FOR NORMAL SLEW RATE - 20.0KBIT/SEC ACCORDING TO LIN PHYSICAL
LAYER SPECIFICATION(48), (49)
Duty Cycle 1:
D1
THREC(MAX) = 0.744 * VSUP
THDOM(MAX) = 0.581 * VSUP
D1 = tBUS_REC(MIN)/(2 x tBIT), tBIT = 50 µs, 7.0 V ≤ VSUP ≤ 18 V
Duty Cycle 2:
0.396
—
—
—
—
0.581
D2
THREC(MIN) = 0.422 * VSUP
THDOM(MIN) = 0.284 * VSUP
D2 = tBUS_REC(MAX)/(2 x tBIT), tBIT = 50 µs, 7.6 V ≤ VSUP ≤ 18 V
LIN PHYSICAL LAYER: DRIVER CHARACTERISTICS FOR SLOW SLEW RATE - 10.4KBIT/SEC ACCORDING TO LIN PHYSICAL LAYER
SPECIFICATION(48), (50)
Duty Cycle 3:
D3
THREC(MAX) = 0.778 * VSUP
THDOM(MAX) = 0.616 * VSUP
D3 = tBUS_REC(MIN)/(2 x tBIT), tBIT = 96 µs, 7.0 V ≤ VSUP ≤ 18 V
Duty Cycle 4:
0.417
—
—
—
—
0.590
D4
THREC(MIN) = 0.389 * VSUP
THDOM(MIN) = 0.251 * VSUP
D4 = tBUS_REC(MAX)/(2 x tBIT), tBIT = 96 µs, 7.6 V ≤ VSUP ≤ 18 V
Notes
48. Bus load RBUS and CBUS 1.0 nF / 1.0 kΩ, 6.8 nF / 660 Ω, 10 nF / 500 Ω. Measurement thresholds: 50% of TXD signal to LIN signal
threshold defined at each parameter. See Figure 6.
49. See Figure 7.
50. See Figure 8.
33910
18
Analog Integrated Circuit Device Data
Freescale Semiconductor
MC33910G5AC/MC3433910G5AC
ELECTRICAL CHARACTERISTICS
DYNAMIC ELECTRICAL CHARACTERISTICS
Table 5. Dynamic Electrical Characteristics (continued)
Characteristics noted under conditions 5.5 V ≤ VSUP ≤ 18 V, -40°C ≤ TA ≤ 125°C for the 33910 and -40°C ≤ TA ≤ 85°C for the
34910, unless otherwise noted. Typical values noted reflect the approximate parameter mean at TA = 25°C under nominal
conditions, unless otherwise noted.
Characteristic
Symbol
Min
Typ
Max
Unit
SRFAST
—
20
—
V / μs
t REC_PD
—
4.2
6.0
t REC_SYM
- 2.0
—
2.0
t PROPWL
42
70
95
t WAKE_SLEEP
—
—
1500
t WAKE_STOP
9.0
27
35
t TXDDOM
0.65
1.0
1.35
LIN PHYSICAL LAYER: DRIVER CHARACTERISTICS FOR FAST SLEW RATE
LIN Fast Slew Rate (Programming Mode)
LIN PHYSICAL LAYER: CHARACTERISTICS AND WAKE-UP TIMINGS
(51)
Propagation Delay and Symmetry(52)
μs
Propagation Delay of Receiver, tREC_PD=MAX (tREC_PDR, tREC_PDF)
Symmetry of Receiver Propagation Delay, tREC_PDF - tREC_PDR
Bus Wake-Up Deglitcher (Sleep and Stop
modes)(53)(57) (54)
Bus Wake-Up Event Reported
From Sleep mode
(55)
From Stop mode(56)
TXD Permanent Dominant State Delay
μs
μs
s
PULSE WIDTH MODULATION INPUT PIN (PWMIN)
PWMIN pin(57)
fPWMIN
Max. frequency to drive HS output pins
kHz
10
Notes
51. VSUP from 7.0 to 18 V, bus load RBUS and CBUS 1.0 nF / 1.0 kΩ, 6.8 nF / 660 Ω, 10 nF / 500 Ω. Measurement thresholds: 50% of TXD
signal to LIN signal threshold defined at each parameter. See Figure 6.
52. See Figure 9
53. See Figure 10, for Sleep and Figure 11, for Stop mode.
54. This parameter is tested on automatic tester but has not been monitoring during operating life test.
55. The measurement is done with 1.0 µF capacitor and 0 mA current load on VDD. The value takes into account the delay to charge the
capacitor. The delay is measured between the bus wake-up threshold (VBUSWU) rising edge of the LIN bus and when VDD reaches 3.0 V.
See Figure 10. The delay depends of the load and capacitor on VDD.
56.
In Stop mode, the delay is measured between the bus wake-up threshold (VBUSWU) and the falling edge of the IRQ pin. See Figure 11.
57.
This parameter is guaranteed by process monitoring but not production tested.
33910
Analog Integrated Circuit Device Data
Freescale Semiconductor
19
MC33910G5AC/MC3433910G5AC
ELECTRICAL CHARACTERISTICS
TIMING DIAGRAMS
TIMING DIAGRAMS
33910
1.0 nF
LIN
TRANSIENT PULSE
GENERATOR
(NOTE)
GND
PGND LGND
AGND
Note Waveform per ISO 7637-2. Test Pulses 1, 2, 3a, 3b.
Figure 4. Test Circuit for Transient Test Pulses (LIN)
33910
Transient Pulse
Generator
(Note)
1.0 nF
L1
10 kΩ
GND
PGND LGND AGND
Note Waveform per ISO 7637-2. Test Pulses 1, 2, 3a, 3b,.
Figure 5. Test Circuit for Transient Test Pulses (L1)
VSUP
TXD
LIN
R0
RXD
C0
R0 AND C0 COMBINATIONS:
• 1.0 KΩ and 1.0 nF
• 660 Ω and 6.8 nF
• 500 Ω and 10 nF
Figure 6. Test Circuit for LIN Timing Measurements
33910
20
Analog Integrated Circuit Device Data
Freescale Semiconductor
MC33910G5AC/MC3433910G5AC
ELECTRICAL CHARACTERISTICS
TIMING DIAGRAMS
TXD
tBIT
tBIT
tBUS_DOM(MAX)
VLIN_REC
THREC(MAX)
74.4% VSUP
THDOM(MAX)
58.1% VSUP
tBUS_REC(MIN)
Thresholds of
receiving node 1
LIN
THREC(MIN)
THDOM(MIN)
Thresholds of
receiving node 2
42.2% VSUP
28.4% VSUP
tBUS_DOM(MIN)
tBUS_REC(MAX)
RXD
Output of receiving Node 1
tREC_PDF(1)
tREC_PDR(1)
RXD
Output of receiving Node 2
tREC_PDF(2)
tREC_PDR(2)
Figure 7. LIN Timing Measurements for Normal Slew Rate
TXD
tBIT
tBIT
tBUS_DOM(MAX)
VLIN_REC
THREC(MAX)
77.8% VSUP
THDOM(MAX)
61.6% VSUP
tBUS_REC(MIN)
Thresholds of
receiving node 1
LIN
THREC(MIN)
THDOM(MIN)
Thresholds of
receiving node 2
38.9% VSUP
25.1% VSUP
tBUS_DOM(MIN)
tBUS_REC(MAX)
RXD
Output of receiving Node 1
tREC_PDF(1)
tREC_PDR(1)
RXD
Output of receiving Node 2
tREC_PDR(2)
tREC_PDF(2)
Figure 8. LIN Timing Measurements for Slow Slew Rate
33910
Analog Integrated Circuit Device Data
Freescale Semiconductor
21
MC33910G5AC/MC3433910G5AC
ELECTRICAL CHARACTERISTICS
TIMING DIAGRAMS
VLIN_REC
VBUSREC
0.6% VSUP
VBUSDOM
0.4% VSUP
VSUP
LIN BUS SIGNAL
RXD
tREC_PDF
tREC_PDR
Figure 9. LIN Receiver Timing
VLIN_REC
LIN
5.0 V
VBUSWU
DOMINANT LEVEL
3.0 V
VDD
tPROPWL
tWAKE_SLEEP
Figure 10. LIN Wake-up Sleep Mode Timing
VLIN_REC
LIN
5.0 V
VBUSWU
DOMINANT LEVEL
IRQ
tPROPWL
tWAKE_STOP
Figure 11. LIN Wake-up Stop Mode Timing
33910
22
Analog Integrated Circuit Device Data
Freescale Semiconductor
MC33910G5AC/MC3433910G5AC
ELECTRICAL CHARACTERISTICS
TIMING DIAGRAMS
VSUP
VDD
RST
tNRTOUT
tRST
Figure 12. Power On Reset and Normal Request Timeout Timing
tPSCLK
CS
tWSCLKH
tLEAD
tLAG
SCLK
tWSCLKL
tSISU
MOSI
UNDEFINED
D0
tSIH
DON’T CARE
D7
DON’T CARE
tVALID
tSODIS
tSOEN
MISO
D0
DON’T CARE
D7
Figure 13. SPI Timing Characteristics
33910
Analog Integrated Circuit Device Data
Freescale Semiconductor
23
MC33910G5AC/MC3433910G5AC
FUNCTIONAL DESCRIPTION
INTRODUCTION
FUNCTIONAL DESCRIPTION
INTRODUCTION
The 33910 was designed and developed as a highly
integrated and cost-effective solution for automotive and
industrial applications. For automotive body electronics, the
33910 is well suited to perform keypad applications via the
LIN bus.
Power switches are provided on the device configured as
high side outputs. Other ports are also provided, which
include a Hall Sensor port supply, and one wake-up capable
pin. An internal voltage regulator provides power to a MCU
device.
Also included in this device is a LIN physical layer, which
communicates using a single wire. This enables this device
to be compatible with 3-wire bus systems, where one wire is
used for communication, one for battery, and one for ground.
FUNCTIONAL PIN DESCRIPTION
See Figure 1, 33910 Simplified Application Diagram, for a
graphic representation of the various pins referred to in the
following paragraphs. Also, see Pin Connections for a
description of the pin locations in the package.
RECEIVER OUTPUT PIN (RXD)
MASTER OUT SLAVE IN PIN (MOSI)
The MOSI digital pin receives SPI data from the MCU. This
data input is sampled on the negative edge of SCLK.
MASTER IN SLAVE OUT PIN (MISO)
The RXD pin is a digital output. It is the receiver output of
the LIN interface and reports the state of the bus voltage:
RXD Low when LIN bus is dominant, RXD High when LIN bus
is recessive.
The MISO pin sends data to an SPI-enabled MCU. It is a
digital tri-state output used to shift serial data to the
microcontroller. Data on this output pin changes on the
positive edge of the SCLK. When CS is High, this pin will
remain in the high-impedance state.
TRANSMITTER INPUT PIN (TXD)
CHIP SELECT PIN (CS)
The TXD pin is a digital input. It is the transmitter input of
the LIN interface and controls the state of the bus output
(dominant when TXD is Low, recessive when TXD is High).
This pin has an internal pull-up to force recessive state in
case the input is left floating.
CS is an active low digital input. It must remain low during
a valid SPI communication and allow for several devices to
be connected in the same SPI bus without contention. A
rising edge on CS signals the end of the transmission and the
moment the data shifted in is latched. A valid transmission
must consist of 8 bits only.
While in STOP mode, a low-to-high level transition on this
pin will generate a wake-up condition for the 33910.
LIN BUS PIN (LIN)
The LIN pin represents the single-wire bus transmitter and
receiver. It is suited for automotive bus systems and is
compliant to the LIN bus specification 2.0, 2.1, and SAE
J2602-2.
The LIN interface is only active during Normal mode. See
Table 6, Operating Modes Overview.
ANALOG MULTIPLEXER PIN (ADOUT0)
The ADOUT0 pin can be configured via the SPI to allow
the MCU A/D converter to read the several inputs of the
Analog Multiplexer, including the VSENSE and L1 input
voltages, and the internal junction temperature.
SERIAL DATA CLOCK PIN (SCLK)
The SCLK pin is the SPI clock input. MISO data changes
on the positive transition of the SCLK. MOSI is sampled on
the negative edge of the SCLK.
PWM INPUT CONTROL PIN (PWMIN)
This digital input can control the high sides drivers in
Normal Request and Normal mode.
To enable PWM control, the MCU must perform a write
operation to the High Side Control Register (HSCR).
This pin has an internal 20 μA current pull-up.
33910
24
Analog Integrated Circuit Device Data
Freescale Semiconductor
MC33910G5AC/MC3433910G5AC
FUNCTIONAL DESCRIPTION
FUNCTIONAL PIN DESCRIPTION
RESET PIN (RST)
This bidirectional pin is used to reset the MCU in case the
33910 detects a reset condition, or to inform the 33910 that
the MCU has just been reset. After release of the RST pin,
Normal Request mode is entered.
The RST pin is an active low filtered input and output
formed by a weak pull-up and a switchable pull-down
structure which allows this pin to be shorted either to VDD or
to GND during software development, without the risk of
destroying the driver.
INTERRUPT PIN (IRQ)
The IRQ pin is a digital output used to signal events or
faults to the MCU while in Normal and Normal Request mode
or to signal a wake-up from Stop mode. This active low output
will transition to high only after the interrupt is acknowledged
by a SPI read of the respective status bits.
WATCHDOG CONFIGURATION PIN (WDCONF)
The WDCONF pin is the configuration pin for the internal
watchdog. A resistor can be connected to this pin to configure
the window watchdog period. When connected directly to
ground, the watchdog will be disabled. When this pin is left
open, the watchdog period is fixed to its lower precision
internal default value (150 ms typical).
GROUND CONNECTION PINS (AGND, PGND,
LGND)
The AGND, PGND and LGND pins are the Analog and
Power ground pins.
The AGND pin is the ground reference of the voltage
regulator module.
The PGND and LGND pins are used for high current load
return as in the LIN interface pin.
Note: PGND, AGND and LGND pins must be connected
together.
DIGITAL/ANALOG PIN (L1)
The L1 pin is multi purpose input. It can be used as a digital
input, which can be sampled by reading the SPI and used for
wake-up when 33910 is in low power mode or used as analog
input for the analog multiplexer. When used to sense voltage
outside the module, a 33 kohm series resistor must be used
on the input.
When used as wake-up input L1 can be configured to
operate in cyclic-sense mode. In this mode one or both of the
high side switches are configured to be periodically turned on
and sample the wake-up input. If a state change is detected
between two cycles a wake-up is initiated. The 33910 can
also wake-up from Stop or Sleep by a simple state change on
L1.
When used as analog input, the voltage present on the L1
pin is scaled down by an selectable internal voltage divider
and can be routed to the ADOUT0 output through the analog
multiplexer.
Note: If L1 input is selected in the analog multiplexer, it will
be disabled as digital input and remains disabled in low
power mode. No wake-up feature is available in that
condition.
When the L1 input is not selected in the analog
multiplexer, the voltage divider is disconnected from that
input.
HIGH SIDE OUTPUT PINS (HS1 AND HS2)
These two high side switches are able to drive loads such
as relays or lamps. Their structures are connected to the VS2
supply pin. The pins are short-circuit protected and both
outputs are also protected against overheating.
HS1 and HS2 are controlled by SPI and can respond to a
signal applied to the PWMIN input pin.
HS1 and HS2 outputs can also be used during low-power
mode for the cyclic-sense of the wake inputs.
POWER SUPPLY PINS (VS1 AND VS2)
Those are the battery level voltage supply pins. In an
application, VS1 and VS2 pins must be protected against
reverse battery connection and negative transient voltages
with external components. These pins sustain standard
automotive voltage conditions such as a load dump at 40 V.
The high side switches (HS1 and HS2) are supplied by the
VS2 pin. All other internal blocks are supplied by the VS1 pin.
33910
Analog Integrated Circuit Device Data
Freescale Semiconductor
25
MC33910G5AC/MC3433910G5AC
FUNCTIONAL DESCRIPTION
FUNCTIONAL PIN DESCRIPTION
VOLTAGE SENSE PIN (VSENSE)
This input can be connected directly to the battery line. It
is protected against battery reverse connection. The voltage
present in this input is scaled down by an internal voltage
divider, and can be routed to the ADOUT0 output pin and
used by the MCU to read the battery voltage.
The ESD structure on this pin allows for excursion up to
+40 V and down to -27 V, allowing this pin to be connected
directly to the battery line. It is strongly recommended to
connect a 10 kohm resistor in series with this pin for
protection purposes.
HALL SENSOR SWITCHABLE SUPPLY PIN (HVDD)
The HVDD pin needs to be connected to an external
capacitor to stabilize the regulated output voltage.
+5.0 V MAIN REGULATOR OUTPUT PIN (VDD)
An external capacitor has to be placed on the VDD pin to
stabilize the regulated output voltage. The VDD pin is
intended to supply a microcontroller. The pin is current limited
against shorts to GND and over-temperature protected.
During Stop mode, the voltage regulator does not operate
with its full drive capabilities and the output current is limited.
During Sleep mode, the regulator output is completely shut
down.
This pin provides a switchable supply for external hall
sensors. While in Normal mode, this current limited output
can be controlled through the SPI.
33910
26
Analog Integrated Circuit Device Data
Freescale Semiconductor
MC33910G5AC/MC3433910G5AC
FUNCTIONAL DEVICE OPERATIONS
OPERATIONAL MODES
FUNCTIONAL DEVICE OPERATIONS
OPERATIONAL MODES
INTRODUCTION
The 33910 offers three main operating modes: Normal
(Run), Stop, and Sleep (Low Power). In Normal mode, the
device is active and is operating under normal application
conditions. The Stop and Sleep modes are low power modes
with wake-up capabilities.
In Stop mode, the voltage regulator still supplies the MCU
with VDD (limited current capability), while in Sleep mode the
voltage regulator is turned off (VDD = 0 V).
Wake-up from Stop mode is initiated by a wake-up
interrupt. Wake-up from Sleep mode is done by a reset and
the voltage regulator is turned back on.
The selection of the different modes is controlled by the
MOD1:2 bits in the Mode Control Register (MCR).
Figure 14 describes how transitions are done between the
different operating modes. Table 6 gives an overview of the
operating modes.
RESET MODE
The 33910 enters the Reset mode after a power up. In this
mode, the RST pin is low for 1.0 ms (typical value). After this
delay, it enters the Normal Request mode and the RST pin is
driven high.
The Reset mode is entered if a reset condition occurs (VDD
low, watchdog trigger fail, after wake-up from Sleep mode,
Normal Request mode timeout occurs).
NORMAL REQUEST MODE
This is a temporary mode automatically accessed by the
device after the Reset mode, or after a wake-up from Stop
mode.
In Normal Request mode, the VDD regulator is ON, the
RESET pin is High, and the LIN is operating in RX Only
mode.
As soon as the device enters in the Normal Request mode
an internal timer is started for 150 ms (typical value). During
these 150 ms, the MCU must configure the Timing Control
Register (TIMCR) and the Mode Control Register (MCR) with
MOD2 and MOD1 bits set = 0, to enter the Normal mode. If
within the 150 ms timeout, the MCU does not command the
33910 to Normal mode, it will enter in Reset mode. If the
WDCONF pin is grounded in order to disable the watchdog
function, it goes directly in Normal mode after the Reset
mode.
NORMAL MODE
In Normal mode, all 33910 functions are active and can be
controlled by the SPI interface and the PWMIN pin.
The VDD regulator is ON and delivers its full current
capability.
If an external resistor is connected between the WDCONF
pin and the Ground, the window watchdog function will be
enabled.
The wake-up input (L1) can be read as digital input or have
its voltage routed through the analog-multiplexer.
The LIN interface has slew rate and timing compatible with
the LIN protocol specification 2.0, 2.1 and SAEJ2602. The
LIN bus can transmit and receive information.
The high side switches are active and have PWM
capability according to the SPI configuration.
The interrupts are generated to report failures for VSUP
over/under-voltage, thermal shutdown, or thermal shutdown
prewarning on the main regulator.
SLEEP MODE
The Sleep mode is a low power mode. From Normal
mode, the device enters into Sleep mode by sending one SPI
command through the Mode Control Register (MCR), or (VDD
low > 150 ms) with VSUV = 0. When in Reset mode, a VDD
under-voltage condition with no VSUP under-voltage (VSUV =
0) will send the device to Sleep mode. All blocks are in their
lowest power consumption condition. Only some wake-up
sources (wake-up input with or without cyclic sense, forced
wake-up and LIN receiver) are active. The 5.0 V regulator is
OFF. The internal low-power oscillator may be active if the IC
is configured for cyclic-sense. In this condition, one of the
high side switches is turned on periodically and the wake-up
input is sampled.
Wake-up from Sleep mode is similar to a power-up. The
device goes in Reset mode except that the SPI will report the
wake-up source and the BATFAIL flag is not set.
STOP MODE
The Stop mode is the second low power mode, but in this
case the 5.0 V regulator is ON with limited current drive
capability. The application MCU is always supplied while the
33910 is operating in Stop mode.
The device can enter into Stop mode only by sending the
SPI command. When the application is in this mode, it can
wake-up from the 33910 side (for example: cyclic sense,
force wake-up, LIN bus, wake inputs) or the MCU side (CS,
RST pins). Wake-up from Stop mode will transition the 33910
to Normal Request mode and generates an interrupt except
if the wake-up event is a low to high transition on the CS pin
or comes from the RST pin.
33910
Analog Integrated Circuit Device Data
Freescale Semiconductor
27
MC33910G5AC/MC3433910G5AC
FUNCTIONAL DEVICE OPERATIONS
OPERATIONAL MODES
Normal Request
Timeout
Expired
(t NRTOUT
)
Normal Request
timeout
expired (NR
TOUT)
VVDD
Low
DD Low
VDD High and
Normal
Request
VVDDLow
Low
DD
VVDD
LOW (>t NRTOUT
) expired) Expired
DD Low (>NRTOUT
andand
VSUV
=0
VSUV
=0
Wake-up
Wake-Up (Reset)
(Reset)
Sleep
Command
SLEEP
Command
Sleep
Stop
STOPCommand
Command
Normal
WD
Failed
WD
failed
Wake-up
(Interrupt)
Wake-Up Interrupt
Reset
Reset
Delay
(t Delay
VDD
High and
Reset
RST) expired
RST) (tExpired
WD
Disabled
WD disabled
Power Up
WDtrigger
Trigger
WD
Power
Down
Stop
VDD
VDD Low
Low
Legend
WD: Watchdog
Notes:
WD Disabled:
Watchdog disabled (WDCONF pin connected to GND)
WD
- meansisWatchdog
WD Trigger:
Watchdog
triggered by SPI command
WD
means or
Watchdog
disabled
(WDCONF
terminal connected to GND)
WD Failed: No disabled
watchdog- trigger
trigger occurs
in closed
window
WD
trigger
–
means
Watchdog
is triggered by SPI command
Stop Command: Stop command
sent via SPI
WD failed
– means
no Watchdog
trigger or trigger occurs in closed window
Sleep Command:
Sleep
command
sent via SPI
STOP
Command
meanschange,
STOP command
sent via SPI
Wake-up from
Stop
mode: L1- state
LIN bus wake-up,
Periodic wake-up, CS rising edge wake-up or RST wake-up.
SLEEP
Command
means
SLEEP
command
send Periodic
via SPI wake-up.
Wake-up from
Sleep
mode: L1 -state
change,
LIN
bus wake-up,
Wake-Up - means L1 or L2 state change or LIN bus wake up or SS rising edge
Figure 14. Operating Modes and Transitions
33910
28
Analog Integrated Circuit Device Data
Freescale Semiconductor
MC33910G5AC/MC3433910G5AC
FUNCTIONAL DEVICE OPERATIONS
OPERATIONAL MODES
Table 6. Operating Modes Overview
Function
Reset Mode
Normal Request Mode
Normal Mode
Stop Mode
Sleep Mode
VDD
Full
Full
Full
Stop
-
HVDD
-
SPI(58)
SPI
-
-
HSx
-
SPI/PWM(59)
SPI/PWM
Note(60)
Note(61)
Analog Mux
-
SPI
SPI
-
-
L1
-
Input
Input
Wake-up
Wake-up
LIN
-
Rx-Only
Full/Rx-Only
Rx-Only/Wake-up
Wake-up
Watchdog
-
150 ms (typ.) timeout
On(62)/Off
-
-
Voltage Monitoring
VSUP/VDD
VSUP/VDD
VSUP/VDD
VDD
-
Notes
58.
59.
60.
61.
62.
Operation can be enabled/controlled by the SPI.
Operation can be controlled by the PWMIN input.
HSx switches can be configured for cyclic sense operation in Stop mode.
HSx switches can be configured for cyclic sense operation in Sleep mode.
Windowing operation when enabled by an external resistor.
INTERRUPTS
Low-voltage Interrupt:
Interrupts are used to signal a microcontroller that a
peripheral needs to be serviced. The interrupts which can be
generated, change according to the operating mode. While in
Normal and Normal Request modes, the 33910 signals
through interrupts special conditions which may require a
MCU software action. Interrupts are not generated until all
pending wake-up sources are read in the Interrupt Source
Register (ISR).
While in Stop mode, interrupts are used to signal wake-up
events. Sleep mode does not use interrupts. Wake-up is
performed by powering-up the MCU. In Normal and Normal
Request mode the wake-up source can be read by SPI.
The interrupts are signaled to the MCU by a low logic level
of the IRQ pin, which will remain low until the interrupt is
acknowledged by a SPI read command of the ISR register.
The IRQ pin will then be driven high.
Interrupts are only asserted while in Normal, Normal
Request and Stop mode. Interrupts are not generated while
the RST pin is low.
The following is a list of the interrupt sources in Normal and
Normal Request modes. Some of these can be masked by
writing to the SPI - Interrupt Mask Register (IMR).
Signals when the supply line (VS1) voltage drops below
the VSUV threshold (VSUV).
High-voltage Interrupt:
Signals when the supply line (VS1) voltage increases
above the VSOV threshold (VSOV).
Over-temperature Prewarning:
Signals when the 33910 temperature has reached the preshutdown warning threshold. It is used to warn the MCU that
an over-temperature shutdown in the main 5.0 V regulator is
imminent.
LIN Over-temperature Shutdown / TXD Stuck At
Dominant / RXD Short-circuit:
These signal fault conditions within the LIN interface will
cause the LIN driver to be disabled. In order to restart the
operation, the fault must be removed and TXD must go
recessive.
High Side Over-temperature Shutdown:
Signals a shutdown in the high side outputs.
33910
Analog Integrated Circuit Device Data
Freescale Semiconductor
29
MC33910G5AC/MC3433910G5AC
FUNCTIONAL DEVICE OPERATIONS
OPERATIONAL MODES
RESET
To reset a MCU the 33910 drives the RST pin low for the
time the reset condition lasts.
After the reset source is removed, the state machine will
drive the RST output low for at least 1.0 ms (typical value)
before driving it high.
In the 33910, four main reset sources exist:
5.0 V Regulator Low-voltage-Reset (VRSTTH)
The 5.0 V regulator output VDD is continuously monitored
against brown outs. If the supply monitor detects that the
voltage at the VDD pin has dropped below the reset threshold
VRSTTH the 33910 will issue a reset. In case of overtemperature, the voltage regulator will be disabled and the
voltage monitoring will issue a VDDOT Flag independently of
the VDD voltage.
Window Watchdog Overflow
If the watchdog counter is not properly serviced while its
window is open, the 33910 will detect an MCU software runaway and will reset the microcontroller.
Wake-up From Sleep Mode
During Sleep mode, the 5.0 V regulator is not active,
hence all wake-up requests from Sleep mode require a
power-up/reset sequence.
In order to select and activate direct wake-up from L1
input, the Wake-up Control Register (WUCR) must be
configured with appropriate L1WE input enabled or disabled.
The wake-up input’s state is read through the Wake-up
Status Register (WUSR).
L1 input is also used to perform cyclic-sense wake-up.
Note: Selecting an L1 input in the analog multiplexer
before entering low power mode will disable the wake-up
capability of the L1 input
Wake-up from Wake-up input (L1) with cyclic sense timer
enabled
The SBCLIN can wake-up at the end of a cyclic sense
period if on the wake-up input line (L1) a state change occurs.
One or both HSx switch can be activated in Sleep or Stop
modes from an internal timer. Cyclic sense and force wakeup are exclusive. If cyclic sense is enabled, the force wakeup can not be enabled.
In order to select and activate the cyclic sense wake-up
from the L1 input, before entering in low power modes (Stop
or Sleep modes), the following SPI set-up has to be
performed:
In WUCR: select the L1 input to WU-enable.
In HSCR: enable the desired HSx.
• In TIMCR: select the CS/WD bit and determine the
cyclic sense period with CYSTx bits.
• Perform Goto Sleep/Stop command.
External Reset
The 33910 has a bidirectional reset pin which drives the
device to a safe state (same as Reset mode) for as long as
this pin is held low. The RST pin must be held low long
enough to pass the internal glitch filter and get recognized by
the internal reset circuit. This functionality is also active in
Stop mode.
After the RST pin is released, there is no extra t RST to be
considered.
WAKE-UP CAPABILITIES
Once entered into one of the low-power modes (Sleep or
Stop) only wake-up sources can bring the device into Normal
mode operation.
In Stop mode, a wake-up is signaled to the MCU as an
interrupt, while in Sleep mode the wake-up is performed by
activating the 5.0 V regulator and resetting the MCU. In both
cases the MCU can detect the wake-up source by accessing
the SPI registers and reading the Interrupt Source Register.
There is no specific SPI register bit to signal a CS wake-up or
external reset. If necessary this condition is detected by
excluding all other possible wake-up sources.
Wake-up from Wake-up input (L1) with cyclic sense
disabled
Forced Wake-up
The 33910 can wake-up automatically after a
predetermined time spent in Sleep or Stop mode. Cyclic
sense and Forced wake-up are exclusive. If Forced wake-up
is enabled, the Cyclic Sense can not be enabled.
To determine the wake-up period, the following SPI set-up
has to be sent before entering in low power modes:
• In TIMCR: select the CS/WD bit and determine the low
power mode period with CYSTx bits.
• In HSCR: all HSx bits must be disabled.
CS Wake-up
While in Stop mode, a rising edge on the CS will cause a
wake-up. The CS wake-up does not generate an interrupt,
and is not reported on SPI.
LIN Wake-up
While in the low-power mode, the 33910 monitors the
activity on the LIN bus. A dominant pulse larger than t PROPWL
followed by a dominant to recessive transition will cause a
LIN wake-up. This behavior protects the system from a short
to ground bus condition. The bit RXONLY = 1 from LINCR
Register disables the LIN wake-up from Stop mode.
The wake-up line is dedicated to sense state changes of
external switch and wake-up the MCU (in Sleep or Stop
mode).
33910
30
Analog Integrated Circuit Device Data
Freescale Semiconductor
MC33910G5AC/MC3433910G5AC
FUNCTIONAL DEVICE OPERATIONS
OPERATIONAL MODES
RST Wake-up
While in Stop mode, the 33910 can wake-up when the
RST pin is held low long enough to pass the internal glitch
filter. Then, the 33910 will change to Normal Request or
Normal modes depending on the WDCONF pin
configuration. The RST wake-up does not generate an
interrupt and is not reported via SPI.
From Stop mode, the following wake-up events can be
configured:
• Wake-up from L1 input without cyclic sense
• Cyclic sense wake-up inputs
• Force wake-up
• CS wake-up
• LIN wake-up
• RST wake-up
From Sleep mode, the following wake-up events can be
configured:
• Wake-up from L1 input without cyclic sense
• Cyclic sense wake-up inputs
• Force wake-up
• LIN wake-up
WINDOW WATCHDOG
The 33910 includes a configurable window watchdog
which is active in Normal mode. The watchdog can be
configured by an external resistor connected to the WDCONF
pin. The resistor is used to achieve higher precision in the
timebase used for the watchdog.
SPI clears are performed by writing through the SPI in the
MOD bits of the Mode Control Register (MCR).
During the first half of the SPI timeout, watchdog clears are
not allowed, but after the first half of the SPI timeout window,
the clear operation opens. If a clear operation is performed
outside the window, the 33910 will reset the MCU, in the
same way as when the watchdog overflows.
WINDOW CLOSED
NO WATCHDOG CLEAR
ALLOWED
WD TIMING X 50%
WINDOW OPEN
FOR WATCHDOG
CLEAR
WD TIMING X 50%
WD PERIOD (tPWD)
WD TIMING SELECTED BY RESISTOR
ON WDCONF PIN
Figure 15. Window Watchdog Operation
To disable the watchdog function in Normal mode the user
must connect the WDCONF pin to ground. This measure
effectively disables Normal Request mode. The WDOFF bit
in the Watchdog Status Register (WDSR) will be set. This
condition is only detected during Reset mode.
If neither a resistor nor a connection to ground is detected,
the watchdog falls back to the internal lower precision
timebase of 150 ms (typ.) and signals the faulty condition
through the Watchdog Status Register (WDSR).
The watchdog timebase can be further divided by a
prescaler which can be configured by the Timing Control
Register (TIMCR). During Normal Request mode, the
window watchdog is not active but there is a 150 ms (typ.)
timeout for leaving the Normal Request mode. In case of a
timeout, the 33910 will enter into Reset mode, resetting the
microcontroller before entering again into Normal Request
mode.
FAULTS DETECTION MANAGEMENT
The 33910 has the capability to detect faults like an over
or under-voltage on VS1, TxD in permanent Dominant State,
Over-temperature on HS, LIN. It is able to take corrective
actions accordingly. Most of faults are monitoring through
SPI and the Interrupt pin. The microcontroller can also take
actions.
The following table summarizes all fault sources the
device is able to detect with associated conditions. The status
for a device recovery and the SPI or pins monitoring are also
described.
33910
Analog Integrated Circuit Device Data
Freescale Semiconductor
31
MC33910G5AC/MC3433910G5AC
FUNCTIONAL DEVICE OPERATIONS
OPERATIONAL MODES
Table 7. Fault Detection Management Conditions
MONITORING(64)
BLOCK
FAULT
BATTERY FAIL
VSUP OVERVOLTAGE
Power Supply
MODE
All modes
Normal, Normal
Request
VSUP UNDERVOLTAGE
VDD UNDERVOLTAGE
CONDITION
FALLOUT
VSUP<3.0 V (typ)
then power-up
VSUP > 19.25 V (typ)
In Normal mode, HS
shutdown if bit
HVSE=1 (reg MCR)
VSUP < 6.0 V (typ)
All except Sleep
VDD < 4.5 V (typ)
RECOVERY
REG (FLAG,
BIT)
INTERRUPT
Condition gone
VSR (BATFAIL, 0)
-
Condition gone, to
re-enable HS write to
HSCR registers
VSR (VSOV,3)
IRQ low +
ISR (0101)(65)
VSR (VSUV,2)
IRQ low + ISR
(0101)
Reset (63)
-
-
Condition gone
VDD OVER-TEMP
PREWARNING
VDD OVERTEMPERATURE
All except Low
Power modes
RXD PIN SHORT
CIRCUIT
LIN
TXD PIN
PERMANENT
DOMINANT
Normal, Normal
Request
VDD shutdown,
Reset then Sleep
RXD pin shorted to
GND or 5 V
LIN trans shutdown
TXD pin low for more
than 1s (typ)
Temperature >
160°C (typ)
HIGH SIDE DRIVERS
OVERTEMPERATURE
Temperature >
160°C (typ)
HS2 OPEN-LOAD
DETECTION
-
Temperature >
170°C (typ)
LIN DRIVER OVERTEMPERATURE
HS1 OPEN-LOAD
DETECTION
High Side
Temperature >
115°C (typ)
LIN transmitter
shutdown
VSR (VDDOT,1)
IRQ low + ISR
(0101)
-
-
LINSR,
(RXSHORT,3)
LIN transmitter reenabled once the
condition is gone and
TXD is high
LINSR (TXDOM,2)
IRQ low + ISR
(0100)(65)
LINSR (LINOT,1)
Both HS thermal
shutdown
Condition gone, to
re-enable HS write to
HSCR reg
All flags in HSSR
are set
IRQ low + ISR
(0010) (65)
HSSR (HS1OP,1)
Normal, Normal
Request
Current through HSx
< 5.0 mA (typ)
HSSR (HS2OP,3)
Condition gone
HS1 OVERCURRENT
HS2 OVERCURRENT
NORMAL REQUEST
TIME-OUT EXPIRED
Watchdog
Notes
63.
64.
65.
Normal Request
Current through HSx
tends to rise above
the current limit
60 mA (min)
HSx on with limited
current capability
60 mA (min)
The MCU did not
command the device
to Normal mode
within the 150 ms
timeout after reset
Reset
HSSR (HS1CL,0)
HSSR (HS2CL,2)
-
WATCHDOG
TIMEOUT
Normal
WD timeout or WD
clear within the
window closed
Reset
-
WATCHDOG ERROR
Normal
WDCONF pin is
floating
WD internal lower
precision timebase
150 ms (typ)
WDSR (WDTO, 3)
Connect WDCONF
to a resistor or to
GND
WDSR (WDERR, 2)
When in Reset mode a VDD under-voltage condition combined with no VSUP under-voltage (VSUV=0) will send the device to Sleep mode.
Registers to be read when back in Normal Request or Normal mode depending on the fault. Interrupts only generated in Normal, Normal Request and Stop modes
Unless masked, If masked IRQ remains high and the ISR flags are not set.
33910
32
Analog Integrated Circuit Device Data
Freescale Semiconductor
MC33910G5AC/MC3433910G5AC
FUNCTIONAL DEVICE OPERATIONS
OPERATIONAL MODES
TEMPERATURE SENSE GAIN
The analog multiplexer can be configured via SPI to allow
the ADOUT0 pin to deliver the internal junction temperature
of the device.
The graph below illustrates the internal chip temp sense
obtained per characterization at 3 temperatures with 3
different lots and 30 samples.
Temperature Sense Analog Output Voltage
5
4.5
Vadout0 (V)
4
3.5
3
2.5
2
-50
0
50
100
150
Temperature (°C)
Figure 16. Temperature Sense Gain
HIGH SIDE OUTPUT PINS HS1 AND HS2
These outputs are two high side drivers intended to drive
small resistive loads or LEDs incorporating the following
features:
• PWM capability (software maskable)
• Open load detection
• Current limitation
• Over-temperature shutdown (with maskable interrupt)
• High-voltage shutdown (software maskable)
• Cyclic sense
The high side switches are controlled by the bits HS1:2 in
the High Side Control Register (HSCR).
PWM Capability (direct access)
Each high side driver offers additional (to the SPI control)
direct control via the PWMIN pin.
If both the bits HS1 and PWMHS1 are set in the High Side
Control Register (HSCR), then the HS1 driver is turned on if
the PWMIN pin is high and turned of if the PWMIN pin is low.
This applies to HS2 configuring HS2 and PWMHS2 bits.
33910
Analog Integrated Circuit Device Data
Freescale Semiconductor
33
MC33910G5AC/MC3433910G5AC
FUNCTIONAL DEVICE OPERATIONS
OPERATIONAL MODES
Interrupt
Control
Module
MOD1:2
HSx
HSxOP
VDD
VDD
PWMIN
High-Side Interrupt
High Voltage Shutdown
HVSE
PWMHSx
VS2
on/off
Control
Status
HSxCL
High Side Driver
charge pump
open load detection
current limitation
over-temperture shutdown (interrupt maskable)
high voltage shutdown (maskable)
Cyclic Sense
HSx
Wakeup
Module
Figure 17. High Side Drivers HS1 and HS2
Open Load Detection
Each high side driver signals an open load condition if the
current through the high side is below the open load current
threshold.
The open load condition is indicated with the bits HS1OP
and HS2OP in the High Side Status Register (HSSR).
Current Limitation
Each high side driver has an output current limitation. In
combination with the over-temperature shutdown the highside drivers are protected against over-current and shortcircuit failures.
When the driver operates in the current limitation area, it is
indicated with the bits HS1CL and HS2CL in the HSSR.
Note: If the driver is operating in current limitation mode,
excessive power might be dissipated.
Over-temperature Protection (HS Interrupt)
Both high side drivers are protected against overtemperature. In case of an over-temperature condition both
high side drivers are shut down and the event is latched in the
Interrupt Control Module. The shutdown is indicated as HS
Interrupt in the Interrupt Source Register (ISR).
A thermal shutdown of the high side drivers is indicated by
setting all HSxOP and HSxCL bits simultaneously.
If the bit HSM is set in the Interrupt Mask Register (IMR),
then an interrupt (IRQ) is generated.
A write to the High Side Control Register (HSCR), when
the over-temperature condition is gone, will re-enable the
high side drivers.
High-voltage Shutdown
In case of a high voltage condition and if the high voltage
shutdown is enabled (bit HVSE in the Mode Control Register
(MCR) is set both high side drivers are shut down.
A write to the High Side Control Register (HSCR), when
the high voltage condition is gone, will re-enable the high side
drivers.
Sleep And Stop Mode
The high side drivers can be enabled to operate in Sleep
and Stop mode for cyclic sensing. Also see Table 6,
Operating Modes Overview.
LIN PHYSICAL LAYER
The LIN bus pin provides a physical layer for single-wire
communication in automotive applications. The LIN physical
layer is designed to meet the LIN physical layer specification
and has the following features:
• LIN physical layer 2.0, 2.1 and SAEJ2602 compliant
• Slew rate selection
• Over-temperature shutdown
• Advanced diagnostics
The LIN driver is a low side MOSFET with thermal
shutdown. An internal pull-up resistor with a serial diode
structure is integrated, so no external pull-up components are
33910
34
Analog Integrated Circuit Device Data
Freescale Semiconductor
MC33910G5AC/MC3433910G5AC
FUNCTIONAL DEVICE OPERATIONS
OPERATIONAL MODES
required for the application in a slave node. The fall time from
dominant to recessive and the rise time from recessive to
dominant is controlled. The symmetry between both slopes is
guaranteed.
LIN Pin
The LIN pin offers a high susceptibility immunity level from
external disturbance, guaranteeing communication during
external disturbance.
WAKE-UP
MODULE
LIN
Wake-up
MOD1:2
LSR0:1
J2602
VS1
LIN DRIVER
RXONLY
Slope and Slew Rate Control
RXSHORT
Over-temperature Shutdown (interrupt maskable)
TXDOM
LINOT
30 K
LIN
TXD
SLOPE
CONTROL
WAKE-UP
FILTER
LGND
RXD
RECEIVER
Figure 18. LIN Interface
Slew Rate Selection
The slew rate can be selected for optimized operation at
10.4 and 20 kBit/s as well as a fast baud rate for test and
programming. The slew rate can be adapted with the bits
LSR1:0 in the LIN Control Register (LINCR). The initial slew
rate is optimized for 20 kBit/s.
J2602 Conformance
To be compliant with the SAE J2602-2 specification, the
J2602 feature has to be enabled in the LINCR Register (bit
DIS_J2602 sets to 0). The LIN transmitter is disabled in case
of a VSUP under-voltage condition occurs and TXD is in
Recessive State: the LIN bus goes in Recessive State and
RXD goes high. The LIN transmitter is not disabled if TXD is
in Dominant State. A deglitcher on VSUP (tJ2602_DEG) is
implemented to avoid false switching.
If the (DIS_J2602) bit is set to 1, the J2602 feature is
disabled and the communication TXD-LIN-RXD works for
VSUP down to 4.6 V (typical value) and then the
communication is interrupted.
The (DIS_J2602) bit is set per default to 0.
Over-temperature Shutdown (LIN Interrupt)
The output low side FET is protected against overtemperature conditions. In case of an over-temperature
condition, the transmitter will be shut down and the LINOT bit
in the LIN Status Register (LINSR) is set.
If the LINM bit is set in the Interrupt Mask Register (IMR),
an Interrupt IRQ will be generated.
The transmitter is automatically re-enabled once the
condition is gone and TXD is high.
RXD Short-circuit Detection (LIN Interrupt)
The LIN transceiver has a short-circuit detection for the
RXD output pin. If the device transmits and in case of a shortcircuit condition, either 5.0 V or Ground, the RXSHORT bit in
33910
Analog Integrated Circuit Device Data
Freescale Semiconductor
35
MC33910G5AC/MC3433910G5AC
FUNCTIONAL DEVICE OPERATIONS
OPERATIONAL MODES
the LIN Status Register (LINSR) is set and the transmitter is
shut down.
If the LINM bit is set in the Interrupt Mask Register (IMR),
an Interrupt IRQ will be generated.
The transmitter is automatically re-enabled once the
condition is gone (transition on RXD) and TXD is high.
A read of the LIN Status Register (LINSR) without the RXD
pin short-circuit condition will clear the bit RXSHORT.
TXD Dominant Detection (LIN Interrupt)
The LIN transceiver monitors the TXD input pin to detect a
stuck in dominant (0 V) condition. In case of a stuck condition
(TXD pin 0 V for more than 1 second (typ.)), the transmitter is
shut down and the TXDOM bit in the LIN Status Register
(LINSR) is set.
If the LINM bit is set in the IMR, an Interrupt IRQ will be
generated.
The transmitter is automatically re-enabled once TXD is
high.
A read of the LIN Status Register (LINSR) with the TXD pin
at 5.0 V will clear the bit TXDOM.
LIN Receiver Operation Only
While in Normal mode, the activation of the RXONLY bit
disables the LIN TXD driver. In case of a LIN error condition,
this bit is automatically set. If Stop mode is selected with this
bit set, the LIN wake-up functionality is disabled and the RXD
pin will reflect the state of the LIN bus.
STOP Mode And Wake-up Feature
During Stop mode operation, the transmitter of the
physical layer is disabled. The receiver is still active and able
to detect wake-up events on the LIN bus line.
A dominant level longer than TPROPWL followed by a rising
edge will generate a wake-up interrupt, and will be reported
in the Interrupt Source Register (ISR). Also see Figure 11.
SLEEP Mode And Wake-up Feature
During Sleep mode operation, the transmitter of the
physical layer is disabled. The receiver must be active to
detect wake-up events on the LIN bus line.
A dominant level longer than TPROPWL followed by a rising
edge will generate a system wake-up (Reset), and will be
reported in the Interrupt Source Register (ISR). Also see
Figure 10.
33910
36
Analog Integrated Circuit Device Data
Freescale Semiconductor
MC33910G5AC/MC3433910G5AC
FUNCTIONAL DEVICE OPERATIONS
LOGIC COMMANDS AND REGISTERS
LOGIC COMMANDS AND REGISTERS
33910 SPI INTERFACE AND CONFIGURATION
• MISO — Master-in Slave-out
• SCLK— Serial Clock
A complete data transfer via the SPI consists of 1 byte.
The master sends 4 bits of address (A3:A0) + 4 bits of control
information (C3:C0) and the slave replies with 4 system
status bits (VMS,LINS,HSS,n.d.) + 4 bits of status information
(S3:S0).
The serial peripheral interface creates the communication
link between a microcontroller (master) and the 33910.
The interface consists of four pins (see Figure 19):
• CS — Chip Select
• MOSI — Master-out Slave-in
CS
Register Write Data
MOSI
A3
A2
A1
A0
C3
C2
C1
C0
S1
S0
Register Read Data
MISO
VMS LINS HSS
-
S3
S2
SCLK
Read Data Latch
Rising: 33910 changes MISO/
MCU changes MOSI
Write Data Latch
Falling: 33910 samples MOSI/
MCU samples MISO
Figure 19. SPI Protocol
During the inactive phase of the CS (HIGH), the new data
The rising edge of the Chip Select CS indicates the end of
transfer is prepared.
the transfer and latches the write data (MOSI) into the
register. The CS high forces MISO to the high-impedance
The falling edge of the CS indicates the start of a new data
state.
transfer and puts the MISO in the low-impedance state and
Register reset values are described along with the reset
latches the analog status data (Register read data).
condition.
Reset condition is the condition causing the bit to
With the rising edge of the SPI clock (SCLK), the data is
be set to its reset value. The main reset conditions are:
moved to MISO/MOSI pins. With the falling edge of the SPI
- Power-On Reset (POR): the level at which the logic is
clock (SCLK), the data is sampled by the receiver.
reset
and BATFAIL flag sets.
The data transfer is only valid if exactly 8 sample clock
- Reset mode
edges are present during the active (low) phase of CS.
- Reset done by the RST pin (ext_reset)
33910
Analog Integrated Circuit Device Data
Freescale Semiconductor
37
MC33910G5AC/MC3433910G5AC
FUNCTIONAL DEVICE OPERATIONS
LOGIC COMMANDS AND REGISTERS
SPI REGISTER OVERVIEW
Table 8. System Status Register
Adress(A3:A0)
$0 - $F
BIT
Register Name / Read / Write Information
SYSSR - System Status Register
R
7
6
5
4
VMS
LINS
HSS
-
Table 9 summarizes the SPI Register content for Control Information (C3:C0)=W and status information (S3:S0) = R.
Table 9. SPI Register Overview
Adress(A3:A0)
BIT
Register Name / Read / Write Information
3
2
1
0
MCR - Mode Control Register
W
HVSE
0
MOD2
MOD1
VSR - Voltage Status Register
R
VSOV
VSUV
VDDOT
BATFAIL
VSR - Voltage Status Register
R
VSOV
VSUV
VDDOT
BATFAIL
WUCR - Wake-up Control Register
W
0
0
0
L1WE
WUSR - Wake-up Status Register
R
-
-
-
L1
WUSR - Wake-up Status Register
R
-
-
-
L1
LINCR - LIN Control Register
W
DIS_J2602
RXONLY
LSR1
LSR0
LINSR - LIN Status Register
R
RXSHORT
TXDOM
LINOT
0
LINSR - LIN Status Register
R
RXSHORT
TXDOM
LINOT
0
HSCR - High Side Control Register
W
PWMHS2
PWMHS1
HS2
HS1
HSSR - High Side Status Register
R
HS2OP
HS2CL
HS1OP
HS1CL
HSSR - High Side Status Register
R
HS2OP
HS2CL
HS1OP
HS1CL
TIMCR - Timing Control Register
W
CS/WD
WD2
WD1
WD0
CYST2
CYST1
CYST0
WDSR - Watchdog Status Register
R
WDTO
WDERR
WDOFF
WDWO
$B
WDSR - Watchdog Status Register
R
WDTO
WDERR
WDOFF
WDWO
$C
AMUXCR - Analog Multiplexer Control Register
W
L1DS
MX2
MX1
MX0
$D
CFR - Configuration Register
W
HVDD
CYSX8
0
0
IMR - Interrupt Mask Register
W
HSM
0
LINM
VMM
ISR - Interrupt Source Register
R
ISR3
ISR2
ISR1
ISR0
ISR - Interrupt Source Register
R
ISR3
ISR2
ISR1
ISR0
$0
$1
$2
$3
$4
$5
$6
$7
$A
$E
$F
33910
38
Analog Integrated Circuit Device Data
Freescale Semiconductor
MC33910G5AC/MC3433910G5AC
FUNCTIONAL DEVICE OPERATIONS
LOGIC COMMANDS AND REGISTERS
REGISTER DEFINITIONS
HS1CL
System Status Register - SYSSR
HS1OP
The System Status Register (SYSSR) is always
transferred with every SPI transmission and gives a quick
system status overview. It summarizes the status of the
Voltage Monitor Status (VMS), LIN Status (LINS) and High
Side Status (HSS).
Table 10. System Status Register
Read
HS2OP
Figure 22. High Side Status
Mode Control Register - MCR
S7
S6
S5
S4
VMS
LINS
HSS
-
The Mode Control Register (MCR) allows switching
between the operation modes and to configure the 33910.
Writing the MCR will return the VSR.
Table 11. Mode Control Register - $0
VMS - Voltage Monitor Status
This read-only bit indicates that one or more bits in the
VSR are set.
1 = Voltage Monitor bit set
0 = None
BATFAIL
VDDOT
VSUV
HSS
HS2CL
VMS
VSOV
Figure 20. Voltage Monitor Status
LINS - LIN Status
This read-only bit indicates that one or more bits in the
LINSR are set.
1 = LIN Status bit set
0 = None
C3
C2
C1
C0
Write
HVSE
0
MOD2
MOD1
Reset
Value
1
0
-
-
Reset
Condition
POR
POR
-
-
HVSE - High-Voltage Shutdown Enable
This write-only bit enables/disables automatic shutdown of
the high side drivers during a high-voltage VSOV condition.
1 = automatic shutdown enabled
0 = automatic shutdown disabled
MOD2, MOD1 - Mode Control Bits
These write-only bits select the operating mode and allow
clearing the watchdog in accordance with Table 8, Mode
Control Bits.
Table 12. Mode Control Bits
LINOT
TXDOM
LINS
RXSHORT
Figure 21. LIN Status
HSS - High Side Switch Status
This read-only bit indicates that one or more bits in the
HSSR are set.
1 = High Side Status bit set
0 = None
MOD2
MOD1
Description
0
0
Normal Mode
0
1
Stop Mode
1
0
Sleep Mode
1
1
Normal Mode + Watchdog Clear
Voltage Status Register - VSR
Returns the status of the several voltage monitors. This
register is also returned when writing to the Mode Control
Register (MCR).
Table 13. Voltage Status Register - $0/$1
Read
S3
S2
S1
S0
VSOV
VSUV
VDDOT
BATFAIL
33910
Analog Integrated Circuit Device Data
Freescale Semiconductor
39
MC33910G5AC/MC3433910G5AC
FUNCTIONAL DEVICE OPERATIONS
LOGIC COMMANDS AND REGISTERS
VSOV - VSUP Over-voltage
This read-only bit indicates an over-voltage condition on
the VS1 pin.
1 = Over-voltage condition.
0 = Normal condition.
VSUV - VSUP Under-voltage
This read-only bit indicates an under-voltage condition on
the VS1 pin.
1 = Under-voltage condition.
0 = Normal condition.
VDDOT - Main Voltage Regulator Over-temperature
Warning
This read-only bit indicates that the main voltage regulator
temperature reached the Over-temperature Prewarning
Threshold.
1 = Over-temperature Prewarning
0 = Normal
BATFAIL - Battery Fail Flag.
This read-only bit is set during power-up and indicates that
the 33910 had a Power-On-Reset (POR).
Any access to the MCR or VSR will clear the BATFAIL flag.
1 = POR Reset has occurred
0 = POR Reset has not occurred
Wake-up Control Register - WUCR
This register is used to control the digital wake-up input.
Writing the WUCR will return the Wake-Up Status Register
(WUSR).
Table 14. Wake-up Control Register - $2
C3
C2
C1
C0
Write
0
0
0
L1WE
Reset
Value
1
1
1
1
Reset
Condition
POR, Reset mode or ext_reset
L1WE - Wake-up Input Enable
This write-only bit enables/disables the L1 input. In Stop
and Sleep mode the L1WE bit activates the L1 input for wakeup. If the L1 input is selected on the analog multiplexer, the
L1WE is masked to 0.
1 = Wake-up Input enabled.
0 = Wake-up Input disabled.
Wake-up Status Register - WUSR
This register is used to monitor the digital wake-up input
and is also returned when writing to the WUCR.
Table 15. Wake-up Status Register - $2/$3
Read
S3
S2
S1
S0
-
-
-
L1
L1 - Wake-up input 1
This read-only bit indicates the status of the L1 input. If the
L1 input is not enabled, then the Wake-up status will return 0.
After a wake-up from Stop or Sleep mode this bit also
allows to verify the L1 input has caused the wake-up, by first
reading the Interrupt Status Register (ISR) and then reading
the WUSR. The source of the wake-up is only reported on the
first WUCR or WUSR access.
1 = L1 pin high, or L1 is the source of the wake-up.
0 = L1 pin low, disabled or selected as an analog input.
33910
40
Analog Integrated Circuit Device Data
Freescale Semiconductor
MC33910G5AC/MC3433910G5AC
FUNCTIONAL DEVICE OPERATIONS
LOGIC COMMANDS AND REGISTERS
LIN Control Register - LINCR
This register controls the LIN physical interface block.
Writing the LIN Control Register (LINCR) returns the LIN
Status Register (LINSR).
Table 16. LIN Control Register - $4
C3
C2
C1
C0
Write
DIS_J2602
RXONLY
LSR1
LSR0
Reset
Value
0
0
0
0
Reset
Condition
POR
POR, Reset
mode, ext_reset
or LIN failure
gone*
POR
* LIN failure gone: if LIN failure (overtemp, TXD/RXD short) was set,
the flag resets automatically when the failure is gone.
Table 17. LIN Slew Rate Control
LSR1
LSR0
Description
0
0
Normal Slew Rate (up to 20 kb/s)
0
1
Slow Slew Rate (up to 10 kb/s)
1
0
Fast Slew Rate (up to 100 kb/s)
1
1
Reserved
LIN Status Register - LINSR
This register returns the status of the LIN physical
interface block and is also returned when writing to the
LINCR.
Table 18. LIN Status Register - $4/$5
Read
S3
S2
S1
S0
RXSHORT
TXDOM
LINOT
0
J2602 - LIN Dominant Voltage Select
RXSHORT - RXD Pin Short-circuit
This write-only bit controls the J2602 circuitry. If the
circuitry is enabled (bit sets to 0), the TXD-LIN-RXD
communication works down to the battery under-voltage
condition is detected. Below, the bus is in recessive state. If
the circuitry is disabled (bit sets to 1), the communication
TXD-LIN-RXD works down to 4.6 V (typical value).
0 = Enabled J2602 feature.
1 = Disabled J2602 feature.
This read-only bit indicates a short-circuit condition on the
RXD pin (shorted either to 5.0 V or to Ground). The shortcircuit delay must be a worst case of 8.0 µs to be detected
and to shut down the driver. To clear this bit, it must be read
after the condition is gone (transition detected on RXD pin).
The LIN driver is automatically re-enabled once the condition
is gone and TXD is high.
1 = RXD short-circuit condition.
0 = None.
RXONLY - LIN Receiver Operation Only
TXDOM - TXD Permanent Dominant
This write-only bit controls the behavior of the LIN
transmitter.
In Normal mode, the activation of the RXONLY bit disables
the LIN transmitter. In case of a LIN error condition, this bit is
automatically set.
In Stop mode this bit disables the LIN wake-up
functionality, and the RXD pin will reflect the state of the LIN
bus.
1 = only LIN receiver active (Normal mode) or LIN wakeup disabled (Stop mode).
0 = LIN fully enabled.
This read-only bit signals the detection of a TXD pin stuck
at dominant (Ground) condition and the resultant shutdown in
the LIN transmitter. This condition is detected after the TXD
pin remains in dominant state for more than 1 second (typical
value).
To clear this bit, it must be read after TXD has gone high.
The LIN driver is automatically re-enabled once TXD goes
High.
1 = TXD stuck at dominant fault detected.
0 = None.
LSRx - LIN Slew-Rate
LINOT - LIN Driver Over-temperature
This write-only bit controls the LIN driver slew-rate in
accordance with Table 18.
This read-only bit signals that the LIN transceiver was
shutdown due to over-temperature. The transmitter is
automatically re-enabled after the over-temperature
condition is gone and TXD is high. The LINOT bit is cleared
after SPI read once the condition is gone.
1 = LIN over-temperature shutdown
0 = None
33910
Analog Integrated Circuit Device Data
Freescale Semiconductor
41
MC33910G5AC/MC3433910G5AC
FUNCTIONAL DEVICE OPERATIONS
LOGIC COMMANDS AND REGISTERS
High Side Control Register - HSCR
0 = Normal
This register controls the operation of the high side drivers.
Writing to this register returns the High Side Status Register
(HSSR).
Table 19. High Side Control Register - $6
C3
C2
C1
C0
Write
PWMHS2
PWMHS1
HS2
HS1
Reset
Value
0
0
0
0
Timing Control Register - TIMCR
This register allows to configure the watchdog, the cyclic
sense and Forced Wake-up periods. Writing to the Timing
Control Register (TIMCR) will also return the Watchdog
Status Register (WDSR).
Table 21. Timing Control Register - $A
C3
Reset
Condition
Write
POR, Reset mode, ext_reset, HSx
over-temp or (VSOV & HVSE)
POR
This write-only bit enables/disables the PWMIN input pin
to control the respective high side switch. The corresponding
high side switch must be enabled (HSx bit).
1 = PWMIN input controls HSx output.
0 = HSx is controlled only by SPI.
HSx - HSx Switch Control.
This write-only bit enables/disables the corresponding
high side switch.
1 = HSx switch on.
0 = HSx switch off.
High Side Status Register - HSSR
This register returns the status of the high side switches
and is also returned when writing to the HSCR.
Table 20. High Side Status Register - $6/$7
C1
C0
WD2
WD1
WD0
CYST2
CYST1
CYST0
0
0
0
CS/WD
Reset
Value
-
Reset
Condition
-
PWMHSx - PWM Input Control Enable.
C2
POR
CS/WD - Cyclic Sense or Watchdog prescaler select
This write-only bit selects which prescaler is being written
to, the Cyclic Sense/Forced Wake-up prescaler or the
Watchdog prescaler.
1 = Cyclic Sense/Forced Wake-up Prescaler selected
0 = Watchdog Prescaler select
WDx - Watchdog Prescaler
This write-only bits selects the divider for the watchdog
prescaler and therefore selects the watchdog period in
accordance with Table 22. This configuration is valid only if
windowing watchdog is active.
Table 22. Watchdog Prescaler
WD2
WD1
WD0
Prescaler Divider
0
0
0
1
0
0
1
2
High Side thermal shutdown
0
1
0
4
A thermal shutdown of the high side drivers is indicated by
setting all HSxOP and HSxCL bits simultaneously.
0
1
1
6
1
0
0
8
1
0
1
10
1
1
0
12
1
1
1
14
S3
Read
HS2OP
S2
HS2CL
S1
HS1OP
S0
HS1CL
HSxOP - High Side Switch Open-Load Detection
This read-only bit signals that the high side switches are
conducting current below a certain threshold indicating
possible load disconnection.
1 = HSx Open Load detected (or thermal shutdown)
0 = Normal
HSxCL - High Side Current Limitation
This read-only bit indicates that the respective high side
switch is operating in current limitation mode.
1 = HSx in current limitation (or thermal shutdown)
CYSTx - Cyclic Sense Period Prescaler Select
This write-only bits selects the interval for the wake-up
cyclic sensing together with the bit CYSX8 in the
Configuration Register (CFR) (see page 44).
This option is only active if one of the high side switches is
enabled when entering in Stop or Sleep mode. Otherwise, a
timed wake-up is performed after the period shown in
Table 23.
33910
42
Analog Integrated Circuit Device Data
Freescale Semiconductor
MC33910G5AC/MC3433910G5AC
FUNCTIONAL DEVICE OPERATIONS
LOGIC COMMANDS AND REGISTERS
Table 23. Cyclic Sense and Force Wake-up Interval
CYSX8(66)
CYST2
CYST1
CYST0
Interval
X
0
0
0
No cyclic sense(67)
0
0
0
1
20 ms
0
0
1
0
40 ms
0
0
1
1
60 ms
0
1
0
0
80 ms
0
1
0
1
100 ms
0
1
1
0
120 ms
0
1
1
1
140 ms
1
0
0
1
160 ms
1
0
1
0
320 ms
1
0
1
1
480 ms
1
1
0
0
640 ms
1
1
0
1
800 ms
1
1
1
0
960 ms
1
1
1
1
1120 ms
timeouts are disabled and the device automatically enters
Normal mode out of Reset. This might be necessary for
software debugging and for programming the Flash memory.
1 = Watchdog is disabled
0 = Watchdog is enabled
WDWO - Watchdog Window Open
This read-only bit signals when the watchdog window is
open for clears. The purpose of this bit is for testing. Should
be ignored in case WDERR is High.
1 = Watchdog window open
0 = Watchdog window closed
Analog Multiplexer Control Register - MUXCR
This register controls the analog multiplexer and selects
the divider ration for the L1 input divider.
Table 25. Analog Multiplexer Control Register -$C
Notes
66. bit CYSX8 is located in Configuration Register (CFR)
67. No Cyclic Sense and no Force Wake-up available.
Watchdog Status Register - WDSR
This register returns the Watchdog status information and
is also returned when writing to the TIMCR.
Table 24. Watchdog Status Register - $A/$B
Read
S3
S2
S1
S0
WDTO
WDERR
WDOFF
WDWO
WDTO - Watchdog Timeout
This read-only bit signals the last reset was caused by
either a watchdog timeout or by an attempt to clear the
Watchdog within the window closed.
Any access to this register or the Timing Control Register
(TIMCR) will clear the WDTO bit.
1 = Last reset caused by watchdog timeout
0 = None
C3
C2
C1
C0
Write
L1DS
MX2
MX1
MX0
Reset
Value
1
0
0
0
Reset
Condition
POR
POR, Reset mode or ext_reset
L1DS - L1 Analog Input Divider Select
This write-only bit selects the resistor divider for the L1
analog input. Voltage is internally clamped to VDD.
0 = L1 Analog divider: 1
1 = L1 Analog divider: 3.6 (typ.)
MXx - Analog Multiplexer Input Select
These write-only bits selects which analog input is
multiplexed to the ADOUT0 pin according to Table 26.
When disabled or when in Stop or Sleep mode, the output
buffer is not powered and the ADOUT0 output is left floating
to achieve lower current consumption.
Table 26. Analog Multiplexer Channel Select
MX2
MX1
MX0
Meaning
WDERR - Watchdog Error
0
0
0
Disabled
This read-only bit signals the detection of a missing
watchdog resistor. In this condition the watchdog is using the
internal, lower precision timebase. The Windowing function is
disabled.
1 = WDCONF pin resistor missing
0 = WDCONF pin resistor not floating
0
0
1
Reserved
0
1
0
Die Temperature Sensor
0
1
1
VSENSE input
1
0
0
L1 input
1
0
1
Reserved
1
1
0
Reserved
WDOFF - Watchdog Off
1
1
1
Reserved
This read-only bit signals that the watchdog pin connected
to Ground and therefore disabled. In this case watchdog
33910
Analog Integrated Circuit Device Data
Freescale Semiconductor
43
MC33910G5AC/MC3433910G5AC
FUNCTIONAL DEVICE OPERATIONS
LOGIC COMMANDS AND REGISTERS
Configuration Register - CFR
HSM - High Side Interrupt Mask
This register controls the Hall Sensor Supply enable/
disable and the cyclic sense timing multiplier.
This write-only bit enables/disables interrupts generated in
the high side block.
1 = HS Interrupts Enabled
0 = HS Interrupts Disabled
Table 27. Configuration Register - $D
C3
C2
C1
C0
Write
HVDD
CYSX8
0
0
Reset
Value
0
0
0
0
Reset
Condition
POR, Reset
mode or
ext_reset
POR
POR
POR
LINM - LIN Interrupts Mask
This write-only bit enables/disables interrupts generated in
the LIN block.
1 = LIN Interrupts Enabled
0 = LIN Interrupts Disabled
VMM - Voltage Monitor Interrupt Mask
HVDD - Hall Sensor Supply Enable
This write-only bit enables/disables the state of the hall
sensor supply.
1 = HVDD on
0 = HVDD off
This write-only bit enables/disables interrupts generated in
the Voltage Monitor block. The only maskable interrupt in the
Voltage Monitor Block is the VSUP over-voltage interrupt.
1 = Interrupts Enabled
0 = Interrupts Disabled
Interrupt Source Register - ISR
CYSX8 - Cyclic Sense Timing x 8.
This write-only bit influences the cyclic sense and Forced
Wake-up period as shown in Table 23.
1 = Multiplier enabled
0 = None
Interrupt Mask Register - IMR
This register allows masking of some of the interrupt
sources. No interrupt will be generated to the MCU and no
flag will be set in the ISR register. The 5.0V Regulator overtemperature prewarning interrupt and Under-voltage (VSUV)
interrupts can not be masked and will always cause an
interrupt.
Writing to the IMR will return the ISR.
This register allows the MCU to determine the source of
the last interrupt or wake-up respectively. A read of the
register acknowledges the interrupt and leads IRQ pin to
high, in case there are no other pending interrupts. If there
are pending interrupts, IRQ will be driven high for 10µs and
then be driven low again.
This register is also returned when writing to the Interrupt
Mask Register (IMR).
Table 29. Interrupt Source Register - $E/$F
Read
S3
S2
S1
S0
ISR3
ISR2
ISR1
ISR0
ISRx - Interrupt Source Register
Table 28. Interrupt Mask Register - $E
C3
C2
C1
C0
Write
HSM
0
LINM
VMM
Reset
Value
1
1
1
1
Reset
Condition
These read-only bits indicate the interrupt source following
Table 30. If no interrupt is pending then all bits are 0.
In case more than one interrupt is pending, the interrupt
sources are handled sequentially multiplex.
POR
33910
44
Analog Integrated Circuit Device Data
Freescale Semiconductor
MC33910G5AC/MC3433910G5AC
FUNCTIONAL DEVICE OPERATIONS
Table 30. Interrupt Sources
Interrupt Source
ISR3 ISR2 ISR1 ISR0
Priority
none maskable
maskable
0
0
0
0
no interrupt
no interrupt
none
0
0
0
1
L1 Wake-up from Stop and Sleep mode
-
highest
0
0
1
0
-
HS Interrupt (Over-temperature)
0
0
1
1
-
Reserved
0
1
0
0
LIN Wake-up
LIN Interrupt (RXSHORT, TXDOM, LIN OT)
0
1
0
1
Voltage Monitor Interrupt
Voltage Monitor Interrupt
(Low Voltage and VDD over-temperature)
(High Voltage)
Forced Wake-up
-
0
1
1
0
lowest
33910
Analog Integrated Circuit Device Data
Freescale Semiconductor
45
MC33910G5AC/MC3433910G5AC
TYPICAL APPLICATION
TYPICAL APPLICATION
The 33910 can be configured in several applications. The figure below shows the 33910 in the typical Slave Node Application.
V
BAT
VS2
VS1
D1
C2
C1
C4
Interrupt
Control Module
LVI, HVI, HTI, OCI
IRQ
C3
Internal Bus
VDD
Voltage Regulator
C5
AGND
5V Output Module
VDD
IRQ
HVDD
Hall Sensor Supply
Reset
Control Module
LVR, HVR, HTR, WD,
RST
RST
TIMER
Window
Watchdog Module
PWMIN
R1
High Side Control
Module
HS2
MISO
MOSI
Chip Temp Sense Module
SCLK
Analog Multiplexer
SPI
&
CONTROL
SPI
CS
MCU
HS1
VSENSE
VBAT Sense Module
L1
R2
Analog Input Module
A/D
ADOUT0
Wake Up Module
Digital Input Module
RXD
LIN Physical Layer
SCI
LIN
LIN
TXD
C6
WDCONF
LGND
AGND
PGND
A/D
R7
Typical Component Values:
C1 = 47 µF; C2 = C4 = 100 nF; C3 = 10 µF; C5 = 220 pF
R1 = 10 kΩ; R2 = 20 kΩ-200 kΩ
Recommended Configuration of the not Connected Pins (NC):
Pin 15, 16, 17, 19, 20, 21, 22 = GND
Pin 11 = open (floating)
Pin 28 = this pin is not internally connected and may be used for PCB routing optimization.
33910
46
Analog Integrated Circuit Device Data
Freescale Semiconductor
MC33910BAC / MC34910BAC
MC33911BAC PRODUCT SPECIFICATIONS PAGES 47 TO 86
MC33911BAC PRODUCT SPECIFICATIONS
PAGES 47 TO 86
33910
Analog Integrated Circuit Device Data
Freescale Semiconductor
47
MC33910G5AC/MC3433910G5AC
INTERNAL BLOCK DIAGRAM
INTERNAL BLOCK DIAGRAM
RST IRQ
INTERRUPT
CONTROL
MODULE
LVI, HVI, HTI, OCI
VS1
INTERNAL BUS
VS2
VDD
AGND
VOLTAGE REGULATOR
PGND
RESET CONTROL
MODULE
LVR, HVR, HTR, WD
5V OUTPUT
MODULE
WINDOW
WATCHDOG
MODULE
HVDD
VS2
HIGH SIDE
CONTROL
MODULE
PWMIN
VS2
MISO
SCLK
HS2
SPI
&
CONTROL
ANALOG MULTIPLEXER
MOSI
CS
ADOUT0
WAKE-UP MODULE
RXD
TXD
HS1
VBAT
SENSE MODULE
VSENSE
CHIP TEMPERATURE
SENSE MODULE
ANALOG INPUT
MODULE
L1
DIGITAL INPUT MODULE
LIN PHYSICAL
LAYER
LIN
LGND
WDCONF
Figure 23. 33910 Simplified Internal Block Diagram
33910
48
Analog Integrated Circuit Device Data
Freescale Semiconductor
MC33910BAC / MC34910BAC
PIN CONNECTIONS
AGND
VDD
HVDD
VSENSE
NC
VS1
VS2
HS1
32
31
30
29
28
27
26
25
PIN CONNECTIONS
RXD
1
24
HS2
TXD
2
23
L1
MISO
3
22
NC*
MOSI
4
21
NC*
SCLK
5
20
NC*
CS
6
19
NC*
ADOUT0
7
18
PGND
PWMIN
8
17
NC*
9
10
11
12
13
14
15
16
RST
IRQ
NC*
WDCONF
LIN
LGND
NC*
NC*
* Special Configuration Recommended /
Mandatory for Marked NC Pins
Figure 24. 33910 Pin Connections
Table 31. 33910 Pin Definitions
A functional description of each pin can be found in the Functional Pin Description.
Pin
Pin Name
Formal Name
Definition
1
RXD
Receiver Output
This pin is the receiver output of the LIN interface which reports the state of
the bus voltage to the MCU interface.
2
TXD
Transmitter Input
This pin is the transmitter input of the LIN interface which controls the state of
the bus output.
3
MISO
SPI Output
4
MOSI
SPI Input
SPI data input.
5
SCLK
SPI Clock
SPI clock Input.
6
CS
SPI Chip Select
7
ADOUT0
Analog Output Pin 0
8
PWMIN
PWM Input
9
RST
Internal Reset I/O
Bidirectional reset I/O pin - driven low when any internal reset source is
asserted. RST is active low.
10
IRQ
Internal Interrupt
Output
Interrupt output pin, indicating wake-up events from Stop mode or events from
Normal and Normal Request modes. IRQ is active low.
11, 15-17,
19-22, 28
NC
SPI data output. When CS is high, the pin is in the high-impedance state.
SPI chip select input pin. CS is active low.
Analog multiplexer output.
High side pulse width modulation input.
No connect
33910
49
Analog Integrated Circuit Device Data
Freescale Semiconductor
MC33910BAC / MC34910BAC
PIN CONNECTIONS
Table 31. 33910 Pin Definitions
A functional description of each pin can be found in the Functional Pin Description.
Pin
Pin Name
Formal Name
Definition
12
WDCONF
Watchdog
Configuration Pin
13
LIN
LIN Bus
14
LGND
LIN Ground Pin
This pin is the device LIN ground connection. It is internally connected to the
PGND pin.
18
PGND
Power Ground Pin
This pin is the device power ground connection. It is internally connected to
the LGND pin.
23
L1
Wake-up Input
This pin is a wake-up capable digital input(68). In addition, L1 can be sensed
analog via the analog multiplexer.
24, 25
HS2, HS1
High Side Outputs
High side switch outputs.
26, 27
VS2, VS1
Power Supply Pin
These pins are device battery level power supply pins. VS2 is supplying the
HS1 driver while VS1 supplies the remaining blocks.(69)
29
VSENSE
Voltage Sense Pin
Battery voltage sense input.(70)
30
HVDD
Hall Sensor Supply
Output
+5.0 V switchable supply output pin.(71)
31
VDD
Voltage Regulator
Output
+5.0 V main voltage regulator output pin.(72)
32
AGND
Analog Ground Pin
This pin is the device analog ground connection.
This input pin is for configuration of the watchdog period and allows the
disabling of the watchdog.
This pin represents the single-wire bus transmitter and receiver.
Notes
68. When used as digital input, a series 33kΩ resistor must be used to protect against automotive transients.
69. Reverse battery protection series diodes must be used externally to protect the internal circuitry.
70. This pin can be connected directly to the battery line for voltage measurements. The pin is self protected against reverse battery
connections. It is strongly recommended to connect a 10kΩ resistor in series with this pin for protection purposes.
71. External capacitor (1.0 µF < C < 10 µF; 0.1 Ω < ESR < 5.0 Ω) required.
72. External capacitor (2.0 µF < C < 100 µF; 0.1 Ω < ESR < 10 Ω) required.
33910
Analog Integrated Circuit Device Data
Freescale Semiconductor
50
MC33910BAC / MC34910BAC
ELECTRICAL CHARACTERISTICS
MAXIMUM RATINGS
ELECTRICAL CHARACTERISTICS
MAXIMUM RATINGS
Table 32. Maximum Ratings
All voltages are with respect to ground, unless otherwise noted. Exceeding these ratings may cause a malfunction or
permanent damage to the device.
Ratings
Symbol
Value
Unit
Normal Operation (DC)
VSUP(SS)
-0.3 to 27
Transient Conditions (load dump)
VSUP(PK)
-0.3 to 40
VDD
-0.3 to 5.5
VIN
-0.3 to VDD+0.3
VIN(IRQ)
-0.3 to 11
HS1 Pin Voltage (DC)
VHS1
- 0.3 to VSUP+0.3
V
HS2 Pin Voltage (DC)
VHS2
- 0.3 to VSUP+0.3
V
Normal Operation with a series 33 kΩ resistor (DC)
VL1DC
-18 to 40
Transient input voltage with external component (according to ISO7637-2)
(See Figure 26)
VL1TR
±100
VVSENSE
-27 to 40
Normal Operation (DC)
VBUSDC
-18 to 40
Transient input voltage with external component (according to ISO7637-2)
(See Figure )
VBUSTR
-150 to 100
IVDD
Internally Limited
Human Body Model - LIN Pin
VESD1-1
± 8000
Human Body Model - all other Pins
VESD1-2
±2000
VESD2
± 150
Corner Pins (Pins 1, 8, 9, 16, 17, 24, 25 and 32)
VESD3-1
± 750
All other Pins (Pins 2-7, 10-15, 18-23, 26-31)
VESD3-2
± 500
VNC
Note 76
ELECTRICAL RATINGS
Supply Voltage at VS1 and VS2
Supply Voltage at VDD
Input / Output Pins Voltage
V
(73)
CS, RST, SCLK, PWMIN, ADOUT0, MOSI, MISO, TXD, RXD
V
V
Interrupt Pin (IRQ)(74)
L1 Pin Voltage
VSENSE Pin Voltage (DC)
V
LIN Pin Voltage
VDD output current
ESD Voltage
V
(75)
Machine Model
V
A
V
Charge Device Model
NC Pin Voltage (NC pins 11, 15, 16, 17, 19, 20, 21, 22, and 28)(76)
Notes
73. Exceeding voltage limits on specified pins may cause a malfunction or permanent damage to the device.
74. Extended voltage range for programming purpose only.
75. Testing is performed in accordance with the Human Body Model (CZAP = 100 pF, RZAP = 1500 Ω), the Machine Model (CZAP = 200 pF,
RZAP = 0 Ω), and the Charge Device Model, Robotic (CZAP = 4.0 pF).
76.
Special configuration recommended / mandatory for marked NC pins. Please refer to the typical application.
33910
51
Analog Integrated Circuit Device Data
Freescale Semiconductor
MC33910BAC / MC34910BAC
ELECTRICAL CHARACTERISTICS
MAXIMUM RATINGS
Table 32. Maximum Ratings (continued)
All voltages are with respect to ground, unless otherwise noted. Exceeding these ratings may cause a malfunction or
permanent damage to the device.
Ratings
Symbol
Value
Unit
THERMAL RATINGS
Operating Ambient Temperature(77)
°C
TA
Operating Junction Temperature(77)
33910
-40 to 125
34910
-40 to 85
TJ
-40 to 150
°C
Storage Temperature
TSTG
-55 to 150
°C
Thermal Resistance, Junction to Ambient
RθJA
°C/W
Natural Convection, Single Layer board (1s)(78), (79)
85
Natural Convection, Four Layer board (2s2p)(78), (80)
56
Thermal Resistance, Junction to Case(81)
Peak Package Reflow Temperature During
Reflow(82), (83)
RθJC
23
°C/W
TPPRT
Note 83
°C
Notes
77. The limiting factor is junction temperature; taking into account the power dissipation, thermal resistance, and heat sinking.
78.
Junction temperature is a function of on-chip power dissipation, package thermal resistance, mounting site (board) temperature, ambient
temperature, air flow, power dissipation of other components on the board, and board thermal resistance.
79.
80.
81.
82.
Per JEDEC JESD51-2 with the single layer board (JESD51-3) horizontal.
Per JEDEC JESD51-6 with the board (JESD51-7) horizontal.
Thermal resistance between the die and the case top surface as measured by the cold plate method (MIL SPEC-883 Method 1012.1).
Pin soldering temperature limit is for 10 seconds maximum duration. Not designed for immersion soldering. Exceeding these limits may
cause malfunction or permanent damage to the device.
Freescale’s Package Reflow capability meets Pb-free requirements for JEDEC standard J-STD-020C. For Peak Package Reflow
Temperature and Moisture Sensitivity Levels (MSL), Go to www.freescale.com, search by part number [e.g. remove prefixes/suffixes
and enter the core ID to view all orderable parts. (i.e. MC33xxxD enter 33xxx), and review parametrics.
83.
33910
Analog Integrated Circuit Device Data
Freescale Semiconductor
52
MC33910BAC / MC34910BAC
ELECTRICAL CHARACTERISTICS
STATIC ELECTRICAL CHARACTERISTICS
STATIC ELECTRICAL CHARACTERISTICS
Table 33. Static Electrical Characteristics
Characteristics noted under conditions 5.5 V ≤ VSUP ≤ 18 V, -40°C ≤ TA ≤ 125°C for the 33910 and -40°C ≤ TA ≤ 85°C for the
34910, unless otherwise noted. Typical values noted reflect the approximate parameter mean at TA = 25°C under nominal
conditions, unless otherwise noted.
Characteristic
Symbol
Min
Typ
Max
Unit
VSUP
5.5
–
18
V
Functional Operating Voltage(84)
VSUPOP
–
–
27
V
Load Dump
VSUPLD
–
–
40
V
IRUN
–
4.5
10
mA
–
48
80
–
58
90
5.5 V < VSUP < 12 V
–
27
35
12 V ≤ VSUP < 13.5 V
–
37
48
ICYCLIC
–
10
–
Threshold (measured on VS1)(88)
VBATFAIL
1.5
3.0
3.9
Hysteresis (measured on VS1)(88)
VBATFAIL_HYS
–
0.9
–
VSUV
5.55
6.0
6.6
VSUV_HYS
–
1.0
–
VSOV
18
19.25
20.5
–
1.0
–
SUPPLY VOLTAGE RANGE (VS1, VS2)
Nominal Operating Voltage
SUPPLY CURRENT RANGE (VSUP = 13.5 V)
Normal Mode (IOUT at VDD = 10 mA), LIN Recessive State(85)
Stop Mode, VDD ON with IOUT = 100 µA, LIN Recessive State
(85), (86), (87)
ISTOP
µA
5.5 V < VSUP < 12 V
VSUP = 13.5 V
Sleep Mode, VDD OFF, LIN Recessive State(85), (87)
Cyclic Sense Supply Current Adder(88)
ISLEEP
µA
µA
SUPPLY UNDER/OVER-VOLTAGE DETECTIONS
Power-On Reset (BATFAIL)(89)
V
VSUP under-voltage detection (VSUV Flag) (Normal and Normal Request
modes, Interrupt Generated)
Threshold (measured on VS1)
Hysteresis (measured on VS1)
V
VSUP over-voltage detection (VSOV Flag) (Normal and Normal Request
modes, Interrupt Generated)
Threshold (measured on VS1)
Hysteresis (measured on VS1)
VSOV_HYS
V
Notes
84. Device is fully functional. All features are operating.
85. Total current (IVS1 + IVS2) measured at GND pins excluding all loads, Cyclic Sense disabled.
86.
Total IDD current (including loads) below 100 µA.
87.
Stop and Sleep mode currents will increase if VSUP exceeds 13.5 V.
88.
89.
This parameter is guaranteed by process monitoring but, not production tested.
The flag is set during power up sequence. To clear the flag, a SPI read must be performed.
33910
53
Analog Integrated Circuit Device Data
Freescale Semiconductor
MC33910BAC / MC34910BAC
ELECTRICAL CHARACTERISTICS
STATIC ELECTRICAL CHARACTERISTICS
Table 33. Static Electrical Characteristics (continued)
Characteristics noted under conditions 5.5 V ≤ VSUP ≤ 18 V, -40°C ≤ TA ≤ 125°C for the 33910 and -40°C ≤ TA ≤ 85°C for the
34910, unless otherwise noted. Typical values noted reflect the approximate parameter mean at TA = 25°C under nominal
conditions, unless otherwise noted.
Characteristic
(90)
VOLTAGE REGULATOR
Symbol
Min
Typ
Max
4.75
5.00
5.25
60
110
200
–
0.1
0.25
Unit
(VDD)
Normal Mode Output Voltage
VDDRUN
1.0 mA < IVDD < 50 mA; 5.5 V < VSUP < 27 V
Normal Mode Output Current Limitation
IVDDRUN
Dropout Voltage(91)
VDDDROP
IVDD = 50 mA
Stop Mode Output Voltage
V
V
VDDSTOP
IVDD < 5.0 mA
mA
V
4.75
5.0
5.25
IVDDSTOP
6.0
12
36
Normal mode, 5.5 V < VSUP < 18 V; IVDD = 10 mA
LRRUN
–
20
25
Stop mode, 5.5 V < VSUP < 18 V; IVDD = 1.0 mA
LRSTOP
–
5.0
25
Normal mode, 1.0 mA < IVDD < 50 mA
LDRUN
–
15
80
Stop mode, 0.1 mA < IVDD < 5.0 mA
LDSTOP
–
10
50
110
125
140
TPRE_HYS
–
10
–
°C
TSD
155
170
185
°C
TSD_HYS
–
10
–
°C
-2.0
–
2.0
20
30
50
Stop Mode Output Current Limitation
Line Regulation
mV
Load Regulation
Over-temperature Prewarning
mA
mV
(Junction)(92)
TPRE
Interrupt generated, Bit VDDOT Set
Over-temperature Prewarning hysteresis(92)
Over-temperature Shutdown Temperature
(Junction)(92)
(92)
Over-temperature Shutdown hysteresis
°C
HALL SENSOR SUPPLY OUTPUT(93) (HVDD)
VDD Voltage matching HVDDACC = (HVDD-VDD) / VDD * 100%
HVDDACC
IHVDD = 15 mA
Current Limitation
Dropout Voltage
IHVDD
HVDDDROP
IHVDD = 15 mA; IVDD = 5.0 mA
Line Regulation
–
160
300
–
25
40
mV
LDHVDD
1.0 mA > IHVDD > 15 mA; IVDD = 5.0 mA
mA
mV
LRHVDD
IHVDD = 5.0 mA; IVDD = 5.0 mA
Load Regulation
%
mV
–
10
20
Notes
90. Specification with external capacitor 2.0 µF < C < 100 µF and 100 mΩ ≤ ESR ≤ 10 Ω.
91. Measured when voltage has dropped 250 mV below its nominal Value (5.0 V).
92. This parameter is guaranteed by process monitoring but, not production tested.
93. Specification with external capacitor 1.0 µF < C < 10 µF and 100 mΩ ≤ ESR ≤ 10 Ω.
33910
Analog Integrated Circuit Device Data
Freescale Semiconductor
54
MC33910BAC / MC34910BAC
ELECTRICAL CHARACTERISTICS
STATIC ELECTRICAL CHARACTERISTICS
Table 33. Static Electrical Characteristics (continued)
Characteristics noted under conditions 5.5 V ≤ VSUP ≤ 18 V, -40°C ≤ TA ≤ 125°C for the 33910 and -40°C ≤ TA ≤ 85°C for the
34910, unless otherwise noted. Typical values noted reflect the approximate parameter mean at TA = 25°C under nominal
conditions, unless otherwise noted.
Characteristic
Symbol
Min
Typ
Max
Unit
VRSTTH
4.3
4.5
4.7
V
0.0
–
0.9
-150
-250
-350
1.5
–
8.0
RST INPUT/OUTPUT PIN (RST)
VDD Low Voltage Reset Threshold
Low-State Output Voltage
VOL
IOUT = 1.5 mA; 3.5 V ≤ VSUP ≤ 27 V
High-state Output Current (0 < VOUT < 3.5 V)
Pull-down Current Limitation (internally limited)
IOH
V
IPD_MAX
VOUT = VDD
µA
mA
Low-state Input Voltage
VIL
-0.3
–
0.3 x VDD
V
High-state Input Voltage
VIH
0.7 x VDD
–
VDD + 0.3
V
0.0
–
1.0
VDD - 0.9
–
VDD
MISO SPI OUTPUT PIN (MISO)
Low-state Output Voltage
VOL
IOUT = 1.5 mA
High-state Output Voltage
VOH
IOUT = -250 µA
Tri-state Leakage Current
V
V
ITRIMISO
0 V ≤ VMISO ≤ VDD
µA
-10
–
10
SPI INPUT PINS (MOSI, SCLK, CS)
Low-state Input Voltage
VIL
-0.3
–
0.3 x VDD
V
High-state Input Voltage
VIH
0.7 x VDD
–
VDD + 0.3
V
MOSI, SCLK Input Current
IIN
0 V ≤ VIN ≤ VDD
CS Pull-up current
µA
-10
–
10
10
20
30
0.0
–
0.8
VDD - 0.8
–
VDD
IPUCS
0 V < VIN < 3.5 V
µA
INTERRUPT OUTPUT PIN (IRQ)
Low-state Output Voltage
VOL
IOUT = 1.5 mA
High-state Output Voltage
VOH
IOUT = -250 µA
Leakage current
V
V
VOH
VDD ≤ VOUT ≤ 10 V
mA
–
–
2.0
PULSE WIDTH MODULATION INPUT PIN (PWMIN)
Low-state Input Voltage
VIL
-0.3
–
0.3 x VDD
V
High-state Input Voltage
VIH
0.7 x VDD
–
VDD + 0.3
V
10
20
30
Pull-up current
0 V < VIN < 3.5 V
IPUPWMIN
µA
33910
55
Analog Integrated Circuit Device Data
Freescale Semiconductor
MC33910BAC / MC34910BAC
ELECTRICAL CHARACTERISTICS
STATIC ELECTRICAL CHARACTERISTICS
Table 33. Static Electrical Characteristics (continued)
Characteristics noted under conditions 5.5 V ≤ VSUP ≤ 18 V, -40°C ≤ TA ≤ 125°C for the 33910 and -40°C ≤ TA ≤ 85°C for the
34910, unless otherwise noted. Typical values noted reflect the approximate parameter mean at TA = 25°C under nominal
conditions, unless otherwise noted.
Characteristic
Symbol
Min
Typ
Max
TJ = 25°C, ILOAD = 50 mA; VSUP > 9.0 V
–
–
7.0
TJ = 150°C, ILOAD = 50 mA; VSUP > 9.0 V(94)
–
–
10
TJ = 150°C, ILOAD = 30 mA; 5.5 V < VSUP < 9.0 V(94)
–
–
14
Unit
HIGH SIDE OUTPUT HS1 AND HS2 PINS (HS1, HS2)
Output Drain-to-Source On Resistance
Output Current Limitation(95)
ILIMHS1
0 V < VOUT < VSUP - 2.0 V
Open Load Current Detection
Ω
RDS(ON)
(96)
Leakage Current (-0.2 V < VHSx < VS2 + 0.2 V)
Short Circuit Detection Threshold
(97)
60
120
250
IOLHSx
–
5.0
7.5
mA
ILEAK
–
–
10
µA
VSUP - 2
–
–
THSSD
150
165
180
°C
THSSD_HYS
–
10
–
°C
2.0
2.5
3.0
VTHSC
5.5 V < VSUP < 27 V
Over-temperature Shutdown(98), (99)
Over-temperature Shutdown Hysteresis(99)
mA
V
L1 INPUT PIN (L1)
Low Detection Threshold
VTHL
5.5 V < VSUP < 27 V
High Detection Threshold
V
VTHH
5.5 V < VSUP < 27 V
V
3.0
3.5
4.0
0.5
1.0
1.5
-10
–
10
800
1550
–
L1DS (L1 Divider Select) = 0
0.95
1.0
1.05
L1DS (L1 Divider Select) = 1
3.42
3.6
3.78
-80
0.0
80
-22
0.0
22
Hysteresis
VHYS
5.5 V < VSUP < 27 V
Input Current(100)
IIN
-0.2 V < VIN < VS1
Analog Input Impedance(101)
Analog Input Divider Ratio (RATIOL1 = VL1 / VADOUT0)
Analog Output Offset Ratio
L1DS (L1 Divider Select) = 0
RL1IN
µA
kΩ
RATIOL1
VRATIOL1OFFSET
L1DS (L1 Divider Select) = 1
Analog Inputs Matching
V
mV
L1MATCHING
%
L1DS (L1 Divider Select) = 0
96
100
104
L1DS (L1 Divider Select) = 1
96
100
104
Notes
94. This parameter is production tested up to TA = 125°C and guaranteed by process monitoring up to TJ = 150°C.
95.
96.
97.
98.
99.
100.
101.
When over-current occurs, the high side stays ON with limited current capability and the HS1CL flag is set in the HSSR.
When open-load occurs, the flag (HS1OP) is set in the HSSR.
When short circuit occurs and if HVSE flag is enabled, HS1 automatic shutdown.
When over-temperature shutdown occurs, both high sides are turned off. All flags in HSSR are set.
Guaranteed by characterization but, not production tested
Analog multiplexer input disconnected from L1 input pin.
Analog multiplexer input connected to L1 input pin.
33910
Analog Integrated Circuit Device Data
Freescale Semiconductor
56
MC33910BAC / MC34910BAC
ELECTRICAL CHARACTERISTICS
STATIC ELECTRICAL CHARACTERISTICS
Table 33. Static Electrical Characteristics (continued)
Characteristics noted under conditions 5.5 V ≤ VSUP ≤ 18 V, -40°C ≤ TA ≤ 125°C for the 33910 and -40°C ≤ TA ≤ 85°C for the
34910, unless otherwise noted. Typical values noted reflect the approximate parameter mean at TA = 25°C under nominal
conditions, unless otherwise noted.
Characteristic
Symbol
Min
Typ
Max
Unit
REXT
20
–
200
kΩ
WDACC
-15
–
15
%
STTOV
–
10.5
–
mV/K
5.0
5.25
5.5
OFFSETVSENS
-30
–
30
E
-45
–
45
VDD - 0.35
–
VDD
0.0
–
0.35
0.0
–
0.8
VDD-0.8
–
VDD
WINDOW WATCHDOG CONFIGURATION PIN (WDCONF)
External Resistor Range
Watchdog Period Accuracy with External Resistor (Excluding Resistor
Accuracy)(102)
ANALOG MULTIPLEXER
Internal Chip Temperature Sense Gain
VSENSE Input Divider Ratio (RATIOVSENSE = VVSENSE / VADOUT0)
RATIOVSENSE
5.5 V < VSUP < 27 V
VSENSE Output Related Offset
-40°C < TA < -20°C
mV
ANALOG OUTPUT (ADOUT0)
Maximum Output Voltage
VOUT_MAX
-5.0 mA < IO < 5.0 mA
Minimum Output Voltage
V
VOUT_MIN
-5.0 mA < IO < 5.0 mA
V
RXD OUTPUT PIN (LIN PHYSICAL LAYER) (RXD)
Low-state Output Voltage
VOL
IOUT = 1.5 mA
High-state Output Voltage
VOH
IOUT = -250 µA
V
V
TXD INPUT PIN (LIN PHYSICAL LAYER) (TXD)
Low-state Input Voltage
VIL
-0.3
–
0.3 x nVDD
V
High-state Input Voltage
VIH
0.7 x VDD
–
VDD + 0.3
V
IPUIN
10
20
30
µA
Pin Pull-up Current, 0 < VIN < 3.5 V
Notes
102. Watchdog timing period calculation formula: tPWD [ms] = 0.466 * (REXT - 20) + 10 (REXT in kΩ)
33910
57
Analog Integrated Circuit Device Data
Freescale Semiconductor
MC33910BAC / MC34910BAC
ELECTRICAL CHARACTERISTICS
STATIC ELECTRICAL CHARACTERISTICS
Table 33. Static Electrical Characteristics (continued)
Characteristics noted under conditions 5.5 V ≤ VSUP ≤ 18 V, -40°C ≤ TA ≤ 125°C for the 33910 and -40°C ≤ TA ≤ 85°C for the
34910, unless otherwise noted. Typical values noted reflect the approximate parameter mean at TA = 25°C under nominal
conditions, unless otherwise noted.
Characteristic
Symbol
Min
Typ
Max
40
120
200
Unit
(103)
LIN PHYSICAL LAYER, TRANSCEIVER (LIN)
Output Current Limitation
IBUSLIM
Dominant State, VBUS = 18 V
mA
Leakage Output Current to GND
Dominant State; VBUS = 0 V; VBAT = 12 V
IBUS_PAS_DOM
-1.0
–
–
mA
Recessive State; 8.0 V < VBAT < 18 V; 8.0 V < VBUS < 18 V; VBUS ≥ VBAT
IBUS_PAS_REC
–
–
20
GND Disconnected; GNDDEVICE = VSUP; VBAT = 12V; 0 < VBUS < 18V
IBUS_NO_GND
-1.0
–
1.0
µA
mA
IBUS
–
–
100
µA
Receiver Dominant State
VBUSDOM
–
–
0.4
Receiver Recessive State
VBUSREC
0.6
–
–
Receiver Threshold Center (VTH_DOM + VTH_REC)/2
VBUS_CNT
0.475
0.5
0.525
Receiver Threshold Hysteresis (VTH_REC - VTH_DOM)
VHYS
–
–
0.175
VLIN_REC
VSUP-1
–
–
Dominant State, TXD LOW, 500 Ω External Pull-up Resistor, LDVS = 0
VLIN_DOM_0
–
1.1
1.4
Dominant State, TXD LOW, 500 Ω External Pull-up Resistor, LDVS = 1
VLIN_DOM_1
–
1.7
2.0
LIN Pull-up Resistor to VSUP
RSLAVE
20
30
60
kΩ
Over-temperature Shutdown(104)
TLINSD
150
165
180
°C
TLINSD_HYS
–
10
–
°C
VBAT disconnected; VSUP_DEVICE = GND; 0 < VBUS < 18V
Receiver Input Voltages
VSUP
LIN Transceiver Output Voltage
Recessive State, TXD HIGH, IOUT = 1.0 µA
Over-temperature Shutdown Hysteresis
V
Notes
103. Parameters guaranteed for 7.0 V ≤ VSUP ≤ 18 V.
104.
When Over-temperature shutdown occurs, the LIN bus goes in recessive state and the flag LINOT in LINSR is set.
33910
Analog Integrated Circuit Device Data
Freescale Semiconductor
58
MC33910BAC / MC34910BAC
ELECTRICAL CHARACTERISTICS
DYNAMIC ELECTRICAL CHARACTERISTICS
DYNAMIC ELECTRICAL CHARACTERISTICS
Table 34. Dynamic Electrical Characteristics
Characteristics noted under conditions 5.5 V ≤ VSUP ≤ 18 V, -40°C ≤ TA ≤ 125°C for the 33910 and -40°C ≤ TA ≤ 85°C for the
34910, unless otherwise noted. Typical values noted reflect the approximate parameter mean at TA = 25°C under nominal
conditions, unless otherwise noted.
Characteristic
Symbol
Min
Typ
Max
Unit
SPI Operating Frequency
f SPIOP
–
–
4.0
MHz
SCLK Clock Period
SPI INTERFACE TIMING (Figure 34)
tPSCLK
250
–
N/A
ns
SCLK Clock High Time(105)
tWSCLKH
110
–
N/A
ns
SCLK Clock Low Time(105)
tWSCLKL
110
–
N/A
ns
Falling Edge of CS to Rising Edge of SCLK(105)
tLEAD
100
–
N/A
ns
Falling Edge of SCLK to CS Rising Edge(105)
tLAG
100
–
N/A
ns
MOSI to Falling Edge of SCLK(105)
tSISU
40
–
N/A
ns
Falling Edge of SCLK to MOSI(105)
tSIH
40
–
N/A
ns
MISO Rise Time(105)
tRSO
–
40
–
CL = 220 pF
MISO Fall Time(105)
tFSO
CL = 220 pF
Time from Falling or Rising Edges of
ns
ns
–
40
–
CS to:(105)
ns
- MISO Low-impedance
tSOEN
0.0
–
50
- MISO High-impedance
tSODIS
0.0
–
50
Time from Rising Edge of SCLK to MISO Data Valid(105)
tVALID
0.0
–
75
t RST
0.65
1.0
1.35
ms
t RSTDF
350
600
900
ns
8.5
10
11.5
0.2 x VDD ≤ MISO ≥ 0.8 x VDD, CL = 100 pF
ns
RST OUTPUT PIN
Reset Low-level Duration after VDD High (See Figure 33)
Reset Deglitch Filter Time
WINDOW WATCHDOG CONFIGURATION PIN (WDCONF)
Watchdog Time Period(106)
External Resistor REXT = 20 kΩ (1%)
t PWD
ms
External Resistor REXT = 200 kΩ (1%)
79
94
108
Without External Resistor REXT (WDCONF Pin Open)
110
150
205
Notes
105. This parameter is guaranteed by process monitoring but, not production tested.
106. Watchdog timing period calculation formula: tPWD [ms] = 0.466 * (REXT - 20) + 10 (REXT in kΩ)
33910
59
Analog Integrated Circuit Device Data
Freescale Semiconductor
MC33910BAC / MC34910BAC
ELECTRICAL CHARACTERISTICS
DYNAMIC ELECTRICAL CHARACTERISTICS
Table 34. Dynamic Electrical Characteristics (continued)
Characteristics noted under conditions 5.5 V ≤ VSUP ≤ 18 V, -40°C ≤ TA ≤ 125°C for the 33910 and -40°C ≤ TA ≤ 85°C for the
34910, unless otherwise noted. Typical values noted reflect the approximate parameter mean at TA = 25°C under nominal
conditions, unless otherwise noted.
Characteristic
Symbol
Min
Typ
Max
Unit
t WUF
8.0
20
38
μs
–
–
5.0
110
150
205
–
–
10
L1 INPUT
Wake-up Filter Time
STATE MACHINE TIMING
Delay Between CS LOW-to-HIGH Transition (at End of SPI Stop Command)
and Stop Mode Activation(107)
Normal Request Mode Timeout (see Figure 33)
Delay Between SPI Command and HS Turn On(108)
t NR TOUT
Delay Between Normal Request and Normal Mode After a Watchdog Trigger
Command (Normal Request mode)(107)
μs
t S-OFF
9.0 V < VSUP < 27 V
–
–
10
–
–
10
μs
t SNR2N
Delay Between CS Wake-up (CS LOW to HIGH) in Stop Mode and:
μs
Normal Request mode, VDD ON and RST HIGH
t WUCS
9.0
15
80
First Accepted SPI Command
t WUSPI
90
—
N/A
t 2CS
4.0
—
—
Minimum Time Between Rising and Falling Edge on the CS
ms
μs
t S-ON
9.0 V < VSUP < 27 V
Delay Between SPI Command and HS Turn Off(108)
μs
t STOP
μs
LIN PHYSICAL LAYER: DRIVER CHARACTERISTICS FOR NORMAL SLEW RATE - 20.0 KBIT/SEC(109), (110)
Duty Cycle 1: D1 = tBUS_REC(MIN)/(2 x tBIT), tBIT = 50 µs
7.0 V ≤ VSUP ≤ 18 V
Duty Cycle 2: D2 = tBUS_REC(MAX)/(2 x tBIT), tBIT = 50 µs
7.6 V ≤ VSUP ≤ 18 V
D1
7.0 V ≤ VSUP ≤ 18 V
Duty Cycle 4: D4 = tBUS_REC(MAX)/(2 x tBIT), tBIT = 96 µs
7.6 V ≤ VSUP ≤ 18 V
—
—
—
—
0.581
D2
LIN PHYSICAL LAYER: DRIVER CHARACTERISTICS FOR SLOW SLEW RATE - 10.4
Duty Cycle 3: D3 = tBUS_REC(MIN)/(2 x tBIT), tBIT = 96 µs
0.396
KBIT/SEC(109),(111)
μs
D3
0.417
—
—
—
—
0.590
μs
D4
Notes
107. This parameter is guaranteed by process monitoring but, not production tested.
108. Delay between turn on or off command (rising edge on CS) and HS ON or OFF, excluding rise or fall time due to external load.
109. Bus load RBUS and CBUS 1.0 nF / 1.0 kΩ, 6.8 nF / 660 Ω, 10 nF / 500 Ω. Measurement thresholds: 50% of TXD signal to LIN signal
threshold defined at each parameter. See Figure 27.
110. See Figure 28.
111. See Figure 29.
33910
Analog Integrated Circuit Device Data
Freescale Semiconductor
60
MC33910BAC / MC34910BAC
ELECTRICAL CHARACTERISTICS
DYNAMIC ELECTRICAL CHARACTERISTICS
Table 34. Dynamic Electrical Characteristics (continued)
Characteristics noted under conditions 5.5 V ≤ VSUP ≤ 18 V, -40°C ≤ TA ≤ 125°C for the 33910 and -40°C ≤ TA ≤ 85°C for the
34910, unless otherwise noted. Typical values noted reflect the approximate parameter mean at TA = 25°C under nominal
conditions, unless otherwise noted.
Characteristic
Symbol
Min
Typ
Max
Unit
SRFAST
—
20
—
V / μs
t REC_PD
—
3.0
6.0
t REC_SYM
- 2.0
—
2.0
t PROPWL
42
70
95
t WAKE
—
—
1500
t WAKE
9.0
13
17
t TXDDOM
0.65
1.0
1.35
—
10
—
LIN PHYSICAL LAYER: DRIVER CHARACTERISTICS FOR FAST SLEW RATE
LIN Fast Slew Rate (Programming mode)
LIN PHYSICAL LAYER: CHARACTERISTICS AND WAKE-UP TIMINGS
(112)
Propagation Delay and Symmetry(113)
μs
Propagation Delay Receiver, tREC_PD=max (tREC_PDR, tREC_PDF)
Symmetry of Receiver Propagation Delay tREC_PDF - tREC_PDR
Bus Wake-up Deglitcher (Sleep and Stop
modes)(114)
Bus Wake-up Event Reported
From Sleep mode
(115)
From Stop mode(116)
TXD Permanent Dominant State Delay
μs
μs
s
PULSE WIDTH MODULATION INPUT PIN (PWMIN)
PWMIN pin(117)
fPWMIN
Max. frequency to drive HS output pins
kHz
Notes
112. VSUP from 7.0 V to 18 V, bus load RBUS and CBUS 1.0 nF / 1.0 kΩ, 6.8 nF / 660 Ω, 10 nF / 500 Ω. Measurement thresholds: 50% of TXD
signal to LIN signal threshold defined at each parameter. See Figure 6.
113. See Figure 9.
114. See Figure 10, for Sleep and Figure 11, for Stop mode.
115. The measurement is done with 1.0 µF capacitor and 0 mA current load on VDD. The value takes into account the delay to charge the
capacitor. The delay is measured between the bus wake-up threshold (VBUSWU) rising edge of the LIN bus and when VDD reaches 3.0 V.
See Figure 10. The delay depends of the load and capacitor on VDD.
116.
In Stop mode, the delay is measured between the bus wake-up threshold (VBUSWU) and the falling edge of the IRQ pin. See Figure 11.
117.
This parameter is guaranteed by process monitoring but, not production tested.
33910
61
Analog Integrated Circuit Device Data
Freescale Semiconductor
MC33910BAC / MC34910BAC
ELECTRICAL CHARACTERISTICS
TIMING DIAGRAMS
TIMING DIAGRAMS
33910
TRANSIENT PULSE
GENERATOR
(NOTE)
1.0 nF
LIN
GND
PGND LGND
AGND
NOTE: Waveform Per ISO 7637-2. Test Pulses 1, 2, 3a, 3b.
Figure 25. Test Circuit for Transient Test Pulses (LIN)
33910
1.0 nF
L1
10 kΩ
PGND LGND
TRANSIENT PULSE
GENERATOR
(NOTE)
GND
AGND
NOTE: Waveform Per ISO 7637-2. Test Pulses 1, 2, 3a, 3b.
Figure 26. Test Circuit for Transient Test Pulses (L1)
VSUP
LIN
TXD
R0
RXD
C0
R0 AND C0 COMBINATIONS:
• 1.0 kΩ and 1.0 nF
• 660 Ω and 6.8 nF
• 500 Ω and 10 nF
Figure 27. Test Circuit for LIN Timing Measurements
33910
Analog Integrated Circuit Device Data
Freescale Semiconductor
62
MC33910BAC / MC34910BAC
ELECTRICAL CHARACTERISTICS
TIMING DIAGRAMS
TXD
tBIT
tBIT
tBUS_DOM (MAX)
VLIN_REC
tREC - MAX
tDOM - MIN
74.4% VSUP
tDOM - MIN
LIN
tBUS_REC (MIN)
58.1% VSUP
40.0% VSUP
58.1% VSUP
40.0% VSUP
60.0% VSUP
28.4% VSUP
28.4% VSUP
42.2% VSUP
tREC - MIN
tDOM - MAX
tBUS_DOM (MIN)
tBUS_REC (MAX)
RXD
tRDOM
tRREC
Figure 28. LIN Timing Measurements for Normal Slew Rate
TXD
tBIT
tBIT
tBUS_DOM (MAX)
VLIN_REC
tREC - MAX
tDOM - MIN
77.8% VSUP
tDOM - MIN
LIN
tBUS_REC (MIN)
61.6% VSUP
40.0% VSUP
61.6% VSUP
40.0% VSUP
60.0% VSUP
25.1% VSUP
25.1% VSUP
38.9% VSUP
tREC - MIN
tDOM - MAX
tBUS_DOM (MIN)
tBUS_REC (MAX)
RXD
tRDOM
tRREC
Figure 29. LIN Timing Measurements for Slow Slew Rate
33910
63
Analog Integrated Circuit Device Data
Freescale Semiconductor
MC33910BAC / MC34910BAC
ELECTRICAL CHARACTERISTICS
TIMING DIAGRAMS
VLIN_REC
VBUSrec
VBUSdom
VSUP
LIN BUS SIGNAL
RXD
tRX_PDF
tRX_PDR
Figure 30. LIN Receiver Timing
VLIN_REC
LIN
0.4 VSUP
DOMINANT LEVEL
VDD
tPROPWL
tWAKE
Figure 31. LIN Wake-up Sleep Mode Timing
VLIN_REC
LIN
0.4 VSUP
DOMINANT LEVEL
IRQ
tPROPWL
tWAKE
Figure 32. LIN Wake-up Stop Mode Timing
33910
Analog Integrated Circuit Device Data
Freescale Semiconductor
64
MC33910BAC / MC34910BAC
ELECTRICAL CHARACTERISTICS
TIMING DIAGRAMS
VSUP
VDD
RST
tNRTOUT
tRST
Figure 33. Power On Reset and Normal Request Timeout Timing
tPSCLK
CS
tWSCLKH
tLEAD
tLAG
SCLK
tWSCLKL
tSISU
MOSI
UNDEFINED
D0
tSIH
DON’T CARE
D7
DON’T CARE
tVALID
tSODIS
tSOEN
MISO
D0
DON’T CARE
D7
Figure 34. SPI Timing Characteristics
33910
65
Analog Integrated Circuit Device Data
Freescale Semiconductor
MC33910BAC / MC34910BAC
FUNCTIONAL DESCRIPTION
INTRODUCTION
FUNCTIONAL DESCRIPTION
INTRODUCTION
The 33910 is designed and developed as a highly
integrated and cost-effective solution for automotive and
industrial applications. For automotive body electronics, the
33910 is well suited to perform keypad applications via the
LIN bus.
Two power switches are provided on the device configured
as high side outputs. Other ports are also provided, which
include a wake-up capable pin amd a Hall Sensor port
supply. An internal voltage regulator provides power to a
MCU device.
Also included in this device is a LIN physical layer, which
communicates using a single wire. This enables this device
to be compatible with 3-wire bus systems, where one wire is
used for communication, one for battery, and one for ground.
FUNCTIONAL PIN DESCRIPTION
See Table 1, 33910 Simplified Application Diagram, for a
graphic representation of the various pins referred to in the
following paragraphs. Also, see the 33910 Pin Connections
for a description of the pin locations in the package.
RECEIVER OUTPUT (RXD)
The RXD pin is a digital output. It is the receiver output of
the LIN interface and reports the state of the bus voltage:
RXD low when LIN bus is dominant, RXD high when LIN bus
is recessive.
TRANSMITTER INPUT (TXD)
The TXD pin is a digital input. It is the transmitter input of
the LIN interface and controls the state of the bus output
(dominant when TXD is Low, recessive when TXD is High).
This pin has an internal pull-up to force recessive state in
case the input is left floating.
LIN BUS (LIN)
The LIN pin represents the single-wire bus transmitter and
receiver. It is suited for automotive bus systems and is
compliant to the LIN bus specification 2.0.
The LIN interface is only active during Normal and Normal
Request modes.
SERIAL DATA CLOCK (SCLK)
The SCLK pin is the SPI clock input pin. MISO data
changes on the negative transition of the SCLK. MOSI is
sampled on the positive edge of the SCLK.
MASTER OUT SLAVE IN (MOSI)
The MOSI digital pin receives SPI data from the MCU. This
data input is sampled on the positive edge of SCLK.
MASTER IN SLAVE OUT (MISO)
The MISO pin sends data to an SPI-enabled MCU. It is a
digital tri-state output used to shift serial data to the
microcontroller. Data on this output pin changes on the
negative edge of the SCLK. When CS is High, this pin will
remain in high-impedance state.
CHIP SELECT (CS)
CS is a active low digital input. It must remain low during a
valid SPI communication and allow for several devices to be
connected in the same SPI bus without contention. A rising
edge on CS signals the end of the transmission and the
moment the data shifted in is latched. A valid transmission
must consist of 8 bits only.
While in STOP mode a low-to-high level transition on this
pin will generate a wake-up condition for the 33910.
ANALOG MULTIPLEXER (ADOUT0)
The ADOUT0 pin can be configured via the SPI to allow
the MCU A/D converter to read the several inputs of the
Analog Multiplexer, including the L1 input voltage and the
internal junction temperature.
PWM INPUT CONTROL (PWMIN)
This digital input can control the high sides in Normal
Request and Normal mode.
To enable PWM control, the MCU must perform a write
operation to the high side control register (HSCR).
This pin has an internal 20 μA current pull-up.
RESET (RST)
This bidirectional pin is used to reset the MCU in case the
33910 detects a reset condition or to inform the 33910 that
the MCU has just been reset. After release of the RST pin
Normal Request mode is entered.
The RST pin is an active low filtered input and output
formed by a weak pull-up and a switchable pull-down
structure which allows this pin to be shorted either to VDD or
to GND during software development without the risk of
destroying the driver.
33910
Analog Integrated Circuit Device Data
Freescale Semiconductor
66
MC33910BAC / MC34910BAC
FUNCTIONAL DESCRIPTION
FUNCTIONAL PIN DESCRIPTION
INTERRUPT (IRQ)
HIGH SIDE OUTPUTS (HS1 AND HS2)
The IRQ pin is a digital output used to signal events or
faults to the MCU while in Normal and Normal Request mode
or to signal a wake-up from Stop mode. This active low output
will transition to high, only after the interrupt is acknowledged
by a SPI read of the respective status bits.
These high side switches are able to drive loads such as
relays or lamps. Their structure is connected to the VS2
supply pin. The pins are short-circuit protected and also
protected against overheating.
HS1and HS2 are controlled by SPI and can respond to a
signal applied to the PWMIN input pin.
The HS1 and HS2 outputs can also be used during Low
Power mode for the cyclic-sense of the wake input.
WATCHDOG CONFIGURATION (WDCONF)
The WDCONF pin is the configuration pin for the internal
watchdog. A resistor can be connected to this pin to configure
the window watchdog period. When connected directly to
ground, the watchdog will be disabled. When this pin is left
open, the watchdog period is fixed to its lower precision
internal default value (150 ms typical).
GROUND CONNECTION (AGND, PGND, LGND)
The AGND, PGND and LGND pins are the Analog and
Power ground pins.
The AGND pin is the ground reference of the voltage
regulator.
The PGND and LGND pins are used for high current load
return as in the LIN interface pin.
Note: PGND, AGND and LGND pins must be connected
together.
DIGITAL/ANALOG (L1)
The L1 pin is a multi purpose input. It can be used as a
digital input, which can be sampled by reading the SPI and
used for wake-up when 33910 is in Low Power mode or used
as analog inputs for the analog multiplexer. When used to
sense voltage outside the module, a 33kohm series resistor
must be used on each input.
When used as a wake-up input L1 can be configured to
operate in Cyclic-Sense mode. In this mode, one of the high
side switches is configured to be periodically turned on and
sample the wake-up input. If a state change is detected
between two cycles a wake-up is initiated. The 33910 can
also wake-up from Stop or Sleep by a simple state change on
L1.
When used as analog input, the voltage present on the L1
pins is scaled down by an selectable internal voltage divider
and can be routed to the ADOUT0 output through the analog
multiplexer.
Note: If L1 input is selected in the analog multiplexer, it will
be disabled as digital input and remains disabled in low
Power mode. No wake-up feature is available in that
condition.
When the L1 input is not selected in the analog
multiplexer, the voltage divider is disconnected from that
input.
POWER SUPPLY (VS1 AND VS2)
Those are the battery level voltage supply pins. In an
application, VS1 and VS2 pins must be protected against
reverse battery connection and negative transient voltages,
with external components. These pins sustain standard
automotive voltage conditions such as load dump at 40 V.
The high side switches (HS1 and HS2) are supplied by the
VS2 pin, all other internal blocks are supplied by VS1 pin.
VOLTAGE SENSE PIN (VSENSE)
This input can be connected directly to the battery line. It
is protected against battery reverse connection. The voltage
present in this input is scaled down by an internal voltage
divider, and can be routed to the ADOUT0 output pin and
used by the MCU to read the battery voltage.
The ESD structure on this pin allows for excursion up to
+40 V, and down to -27 V, allowing this pin to be connected
directly to the battery line. It is strongly recommended to
connect a 10kohm resistor in series with this pin for protection
purposes.
HALL SENSOR SWITCHABLE SUPPLY PIN (HVDD)
This pin provides a switchable supply for external hall
sensors. While in Normal mode, this current limited output
can be controlled through the SPI.
The HVDD pin needs to be connected to an external
capacitor to stabilize the regulated output voltage.
+5V MAIN REGULATOR OUTPUT (VDD)
An external capacitor has to be placed on the VDD pin to
stabilize the regulated output voltage. The VDD pin is
intended to supply a microcontroller. The pin is current limited
against shorts to GND and over-temperature protected.
During Stop mode the voltage regulator does not operate
with its full drive capabilities and the output current is limited.
During Sleep mode the regulator output is completely shut
down.
33910
67
Analog Integrated Circuit Device Data
Freescale Semiconductor
MC33910BAC / MC34910BAC
FUNCTIONAL DESCRIPTION
FUNCTIONAL INTERNAL BLOCK DESCRIPTION
FUNCTIONAL INTERNAL BLOCK DESCRIPTION
MC33910 - Functional Block Diagram
Integrated Supply
Hall Sensor Supply
Voltage Regulator
VDD
HVDD
Analog Circuitry
Window Watchdog
Wake-Up
Digital / Analog Input
Voltage & Temperature Sense
High Side Drivers
HS1 - HS2
LIN Physical Layer
Interface
MCU Interface and Output Control
SPI Interface
Reset & IRQ Logic
HS - PWM Control
Analog Output 0
Integrated Supply
Analog Circuitry
MCU Interface and Output Control
Drivers
Figure 35. Functional Internal Block Diagram
ANALOG CIRCUITRY
The 33910 is designed to operate under automotive
operating conditions. A fully configurable window watchdog
circuit will reset the connected MCU in case of an overflow.
Two low power modes are available with several different
wake-up sources to reactivate the device. One analog / digital
input can be sensed or used as the wake-up source. The
device is capable of sensing the supply voltage (VSENSE)
and the internal chip temperature (CTEMP).
HIGH SIDE DRIVERS
as over-current conditions in any of the driver stages can be
reported to the connected MCU via IRQ or RST. The High
Side driver outputs can be controlled via the SPI register as
well as the PWMIN input. The integrated LIN physical layer
interface can be configured via SPI register and its
communication is driven through the RXD and TXD device
pins. All internal analog sources are multiplexed to the
ADOUT0 pin.
VOLTAGE REGULATOR OUTPUTS
Two current and temperature protected High Side drivers
with PWM capability are provided to drive small loads such as
Status LED’s or small lamps. Both Drivers can be configured
for periodic sense during low power modes.
Two independent voltage regulators are implemented on
the 33910. The VDD main regulator output is designed to
supply a MCU with a precise 5.0 V. The switchable HVDD
output is dedicated to supply small peripherals as hall
sensors.
MCU INTERFACE
LIN PHYSICAL LAYER INTERFACE
The 33910 is providing its control and status information
through a standard 8-Bit SPI interface. Critical system events
such as Low- or High-voltage/Temperature conditions as well
The 33910 provides a LIN 2.0 compatible LIN physical
layer interface with selectable slew rate and various
diagnostic features.
33910
Analog Integrated Circuit Device Data
Freescale Semiconductor
68
MC33910BAC / MC34910BAC
FUNCTIONAL DEVICE OPERATIONS
OPERATIONAL MODES
FUNCTIONAL DEVICE OPERATIONS
OPERATIONAL MODES
INTRODUCTION
NORMAL MODE
The 33910 offers three main operating modes: Normal
(Run), Stop, and Sleep (Low Power). In Normal mode the
device is active and is operating under normal application
conditions. The Stop and Sleep modes are low power modes
with wake-up capabilities.
In Stop mode the voltage regulator still supplies the MCU
with VDD (limited current capability) and in Sleep mode the
voltage regulator is turned off (VDD = 0 V).
Wake-up from Stop mode is initiated by a wake-up
interrupt. Wake-up from Sleep mode is done by a reset and
the voltage regulator is turned back on.
The selection of the different modes is controlled by the
MOD1:2 bits in the mode control register (MCR).
Figure 36 describes how transitions are done between the
different operating modes and Table 35, gives an overview of
the Operating mode.
In Normal mode, all 33910 functions are active and can be
controlled by the SPI and the PWMIN pin.
The VDD regulator is ON and delivers its full current
capability.
If an external resistor is connected between the WDCONF
pin and the Ground, the window watchdog function will be
enabled.
The wake-up input (L1) can be read as a digital input or
have its voltage routed through the analog-multiplexer.
The LIN interface has slew rate and timing compatible with
the LIN protocol specification 2.0. The LIN bus can transmit
and receive information.
The high side switches are active and have PWM
capability according to the SPI configuration.
The interrupts are generated to report failures 5 for VSUP
over/under-voltage, thermal shutdown or thermal shutdown
prewarning on the main regulator.
RESET MODE
The 33910 enters the Reset mode after a power up. In this
mode, the RST pin is low for 1.0 ms (typical value). After this
delay, the 33910 enters the Normal Request mode and the
RST pin is driven high.
The Reset mode is entered if a reset condition occurs (VDD
low, watchdog trigger fail, after a wake-up from Sleep mode,
Normal Request mode timeout occurs).
NORMAL REQUEST MODE
This is a temporary mode automatically accessed by the
device after the Reset mode or after a wake-up from Stop
mode.
In Normal Request mode, the VDD regulator is ON, the
Reset pin is high and the LIN is operating in Rx Only mode.
As soon as the device enters the Normal Request mode
an internal timer is started for 150 ms (typical value). During
these 150 ms, the MCU must configure the timing control
register (TIMCR) and the MCR with MOD2 and MOD1 bits
ste = 0 to enter in Normal mode. If within the 150 ms timeout
the MCU does not command the 33910 to Normal mode, it
will enter in Reset mode. If the WDCONF pin is grounded in
order to disable the watchdog function, the 33910 goes
directly in Normal mode after the Reset mode. If the
WDCONF pin is open, the 33910 stays typically for 150 ms in
Normal Request before entering in Normal mode.
SLEEP MODE
The Sleep mode is a low power mode. From Normal
mode, the device enters the Sleep mode by sending one SPI
command through the MCR. All blocks are in their lowest
power consumption condition. Only some wake-up sources
(wake-up input with or without cyclic sense, forced wake-up
and LIN receiver) are active. The 5.0 V regulator is OFF. The
internal low-power oscillator may be active if the IC is
configured for cyclic-sense. In this condition, one of the high
side switches is turned on periodically and the wake-up
inputs are sampled.
Wake-up from Sleep mode is similar to a power-up. The
device goes in Reset mode except that the SPI will report the
wake-up source and the BATFAIL flag is not set.
STOP MODE
The Stop mode is the second low power mode, but in this
case the 5.0 V regulator is ON with limited current drive
capability. The application MCU is always supplied while the
33910 is operating in Stop mode.
The device can enter in Stop mode only by sending the
SPI command. When the application is in this mode, it can
wake-up from the 33910 side (for example: cyclic sense,
force wake-up, LIN bus, wake inputs) or the MCU side (CS,
RST pins). Wake-up from Stop mode will transition the 33910
to Normal Request mode and generates an interrupt except
if the wake-up event is a low to high transition on the CS pin
or comes from the RST pin.
33910
69
Analog Integrated Circuit Device Data
Freescale Semiconductor
MC33910BAC / MC34910BAC
FUNCTIONAL DEVICE OPERATIONS
OPERATIONAL MODES
Normal Request Timeout Expired (t NRTOUT)
VDD LOW
NORMAL
REQUEST
VDD LOW
VDD LOW (>t NRTOUT) EXPIRED
AND VSUV = 0
SLEEP COMMAND
NORMAL
STOP COMMAND
WD FAILED
WAKE-UP (INTERRUPT)
RESET
VDD HIGH AND
RESET DELAY (t RST) EXPIRED
WD DISABLED
Power Up
WD TRIGGER
POWER
DOWN
WAKE-UP (RESET)
SLEEP
STOP
VDD LOW
Legend
WD: Watchdog
WD Disabled: Watchdog disabled (WDCONF pin connected to GND)
WD Trigger: Watchdog is triggered by SPI command
WD Failed: No watchdog trigger or trigger occurs in closed window
Stop Command: Stop command sent via the SPI
Sleep Command: Sleep command sent via the SPI
Wake-up from Stop mode: L1 state change, LIN bus wake-up, Periodic wake-up, CS rising edge wake-up or RST wake-up.
Wake-up from Sleep mode: L1 state change, LIN bus wake-up, Periodic wake-up.
Figure 36. Operating Modes and Transitions
33910
Analog Integrated Circuit Device Data
Freescale Semiconductor
70
MC33910BAC / MC34910BAC
FUNCTIONAL DEVICE OPERATIONS
OPERATIONAL MODES
Table 35. Operating Modes Overview
Function
Reset Mode Normal Request Mode Normal Mode
Stop Mode
Sleep Mode
VDD
full
full
full
stop
-
HVDD
-
SPI(118)
SPI
-
-
HSx
-
SPI/PWM(119)
SPI/PWM
Note(120)
Note(121)
Analog Mux
-
SPI
SPI
-
-
L1
-
Input
Input
Wake-up
Wake-up
LIN
-
Rx-Only
full/Rx-Only
Rx-Only/Wake-up
Wake-up
Watchdog
-
150 ms (typ.) timeout
On(62)/Off
-
-
VSENSE
On
On
On
VDD
-
Notes
118.
119.
120.
121.
122.
Operation can be enabled/controlled by the SPI.
Operation can be controlled by the PWMIN input.
HSx switches can be configured for cyclic sense operation in Stop mode.
HSx switches can be configured for cyclic sense operation in Sleep mode.
Windowing operation when enabled by an external resistor.
INTERRUPTS
Over-temperature Prewarning
Interrupts are used to signal a microcontroller that a
peripheral needs to be serviced. The interrupts which can be
generated change according to the Operating mode. While in
Normal and Normal Request modes the 33910 signals
through interrupts special conditions which may require a
MCU software action. Interrupts are not generated until all
pending wake-up sources are read in the interrupt source
register (ISR).
While in Stop mode, interrupts are used to signal wake-up
events. Sleep mode does not use interrupts, wake-up is
performed by powering-up the MCU. In Normal and Normal
Request mode the wake-up source can be read by SPI.
The interrupts are signaled to the MCU by a low logic level
of the IRQ pin, which will remain low until the interrupt is
acknowledged by a SPI read. The IRQ pin will then be driven
high.
Interrupts are only asserted while in Normal-, Normal
Request and Stop mode. Interrupts are not generated while
the RST pin is low.
Following is a list of the interrupt sources in Normal and
Normal Request modes, some of those can be masked by
writing to the SPI-interrupt mask register (IMR).
Signals when the 33910 temperature has reached the preshutdown warning threshold. It is used to warn the MCU that
an over-temperature shutdown in the main 5.0 V regulator is
imminent.
Low Voltage Interrupt
Signals when the supply line (VS1) voltage drops below
the VSUV threshold (VSUV).
High Voltage Interrupt
Signals when the supply line (VS1) voltage increases
above the VSOV threshold (VSOV).
LIN Over-current Shutdown / Over-temperature
Shutdown / TXD Stuck At Dominant / RXD Short-circuit
These signal faulty conditions in the LIN interface (except
the LIN over-current) that had led to disable the LIN driver. In
order to restart operation, the fault must be removed and
must be acknowledged by reading the SPI.
The LINOC bit functionality in the LIN status register
(LINSR) is to indicate that an LIN over-current occurred and
the driver stays enabled.
High Side Over-temperature Shutdown
Signals a shutdown of the high side outputs.
RESET
To reset an MCU, the 33910 drives the RST pin low for the
time the reset condition lasts.
After the reset source has been removed the state
machine will drive the RST output low for at least 1.0 ms
typical value before driving it high.
In the 33910 four main reset sources exist:
5V Regulator Low-Voltage-Reset (VRSTTH)
The 5V regulator output VDD is continuously monitored
against brown outs. If the supply monitor detects that the
voltage at the VDD pin has dropped below the reset threshold
VRSTTH the 33910 will issue a reset. In case of overtemperature, the voltage regulator will be disabled and the
33910
71
Analog Integrated Circuit Device Data
Freescale Semiconductor
MC33910BAC / MC34910BAC
FUNCTIONAL DEVICE OPERATIONS
OPERATIONAL MODES
voltage monitoring will issue a VDDOT Flag independently of
the VDD voltage.
Window Watchdog Overflow
If the watchdog counter is not properly serviced while its
window is open, the 33910 will detect a MCU software
runaway and will reset the microcontroller.
Wake-up From Sleep Mode
During Sleep mode, the 5.0 V regulator is not active,
hence all wake-up requests from Sleep mode require a
power-up/reset sequence.
External Reset
The 33910 has a bidirectional reset pin which drives the
device to a safe state (same as Reset mode) for as long as
this pin is held low. The RST pin must be held low long
enough to pass the internal glitch filter and get recognized by
the internal reset circuit. This functionality is also active in
Stop mode.
After the RST pin is released, there is no extra t RST to be
considered.
WAKE-UP CAPABILITIES
Once entered in to one of the low-power modes (Sleep or
Stop) only wake-up sources can bring the device into Normal
mode operation.
In Stop mode, a wake-up is signaled to the MCU as an
interrupt, while in Sleep mode the wake-up is performed by
activating the 5.0 V regulator and resetting the MCU. In both
cases the MCU can detect the wake-up source by accessing
the SPI registers. There is no specific SPI register bit to signal
a CS wake-up or external reset. If necessary this condition is
detected by excluding all other possible wake-up sources.
Wake-up From Wake-up Input (L1) With Cyclic Sense
Disabled
The wake-up line is dedicated to sense state changes of
external switches and wake-up the MCU (in Sleep or Stop
mode).
In order to select and activate direct wake-up from the L1
input, the wake-up control register (WUCR) must be
configured with L1WE input enabled. The wake-up input
state is read through the wake-up status register (WUSR).
L1 input is also used to perform cyclic-sense wake-up.
Note: Selecting the L1 input in the analog multiplexer
before entering Low Power mode will disable the wake-up
capability of the L1 input.
Wake-up From Wake-up Input (L1) With Cyclic Sense
Timer Enabled
The SBCLIN can wake-up at the end of a cyclic sense
period if on the wake-up input lines (L1) a state change
occurs. The HSx switch is activated in Sleep or Stop modes
from an internal timer. Cyclic sense and force wake-up are
exclusive. If cyclic sense is enabled, the force wake-up can
not be enabled.
In order to select and activate the cyclic sense wake-up
from the L1 input, before entering in low power modes (Stop
or Sleep modes), the following SPI set-up has to be
performed:
• In WUCR: select the L1 input to WU-enable.
• In HSCR: enable HSx.
• In TIMCR: select the CS/WD bit and determine the
cyclic sense period with CYSTx bits.
• Perform Goto Sleep/Stop command.
Forced Wake-up
The 33910 can wake-up automatically after a
predetermined time spent in Sleep or Stop mode. Cyclic
sense and forced wake-up are exclusive. If forced wake-up is
enabled, the cyclic sense can not be enabled.
To determine the wake-up period, the following SPI set-up
has to be sent before entering in Low Power modes:
• In TIMCR: select the CS/WD bit and determine the Low
Power mode period with CYSTx bits.
• In HSCR: the HSx bit must be disabled.
CS Wake-up
While in Stop mode, a rising edge on the CS will cause a
wake-up. The CS wake-up does not generate an interrupt
and is not reported on SPI.
LIN Wake-up
While in the low power modes the 33910 monitors the
activity on the LIN bus. A dominant pulse larger than t PROPWL
followed by a dominant to recessive transition will cause a
LIN wake-up. This behavior protects the system from a shortto-ground bus condition.
RST Wake-up
While in Stop mode, the 33910 can wake-up when the
RST pin is held low long enough to pass the internal glitch
filter. Then, the 33910 will change to Normal Request or
Normal modes depending on the WDCONF pin
configuration. The RST wake-up does not generate an
interrupt and is not reported via SPI.
From Stop mode, the following wake-up events can be
configured:
• Wake-up from L1 input without cyclic sense
• Cyclic sense wake-up inputs
• Force wake-up
• CS wake-up
• LIN wake-up
• RST wake-up
From Sleep mode, the following wake-up events can be
configured:
• Wake-up from L1 input without cyclic sense
• Cyclic sense wake-up inputs
• Force wake-up
• LIN wake-up
33910
Analog Integrated Circuit Device Data
Freescale Semiconductor
72
MC33910BAC / MC34910BAC
FUNCTIONAL DEVICE OPERATIONS
OPERATIONAL MODES
WINDOW WATCHDOG
The 33910 includes a configurable window watchdog
which is active in Normal mode. The watchdog can be
configured by an external resistor connected to the WDCONF
pin. The resistor is used to achieve higher precision in the
timebase used for the watchdog.
SPI clears are performed by writing through the SPI in the
MOD bits of the MCR.
During the first half of the SPI timeout watchdog clears are
not allowed; but after the first half of the PSPI-timeout window
the clear operation opens. If a clear operation is performed
outside the window, the 33910 will reset the MCU, in the
same way as when the watchdog overflows.
in the WDSR will be set. This condition is only detected
during Reset mode.
If neither a resistor nor a connection to ground is detected,
the watchdog falls back to the internal lower precision
timebase of 150 ms (typ.) and signals the faulty condition
through the WDSR.
The watchdog timebase can be further divided by a
prescaler which can be configured by the TIMCR. During
Normal Request mode, the window watchdog is not active
but there is a 150 ms (typ.) timeout for leaving the Normal
Request mode. In case of a timeout, the 33910 will enter into
Reset mode, resetting the microcontroller before entering
again into Normal Request mode.
HIGH SIDE OUTPUT PINS HS1 AND HS2
WINDOW CLOSED
NO WATCHDOG CLEAR
ALLOWED
WD TIMING X 50%
WINDOW OPEN
FOR WATCHDOG
CLEAR
WD TIMING X 50%
WD PERIOD (tPWD)
WD TIMING SELECTED BY REGISTER
ON WDCONF PIN
Figure 37. Window Watchdog Operation
To disable the watchdog function in Normal mode the user
must connect the WDCONF pin to ground. This measure
effectively disables Normal Request mode. The WDOFF bit
These outputs are two high side drivers intended to drive
small resistive loads or LEDs incorporating the following
features:
• PWM capability (software maskable)
• Open load detection
• Current limitation
• Over-temperature shutdown (with maskable interrupt)
• High-voltage shutdown (software maskable)
• Cyclic sense
The high side switches are controlled by the bits HS1:2 in
the High Side Control Register (HSCR).
PWM Capability (direct access)
Each high side driver offers additional (to the SPI control)
direct control via the PWMIN pin.
If both the bits HS1 and PWMHS1 are set in the High Side
Control Register (HSCR), then the HS1 driver is turned on if
the PWMIN pin is high and turned of if the PWMIN pin is low.
This applies to HS2 configuring HS2 and PWMHS2 bits.
33910
73
Analog Integrated Circuit Device Data
Freescale Semiconductor
MC33910BAC / MC34910BAC
FUNCTIONAL DEVICE OPERATIONS
OPERATIONAL MODES
Interrupt
Control
Module
MOD1:2
HSx
HSxOP
VDD
VDD
PWMIN
High-Side Interrupt
High Voltage Shutdown
HVSE
PWMHSx
VS2
on/off
Control
Status
HSxCL
High Side - Driver
charge pump
open load detection
current limitation
overtemperture shutdown (interrupt maskable)
high voltage shutdown (maskable)
Cyclic Sense
HSx
Wakeup
Module
Figure 38. High Side Drivers HS1 and HS2
Open Load Detection
Each high side driver signals an open load condition if the
current through the high side is below the open load current
threshold.
The open load condition is indicated with the bits HS1OP
and HS2OP in the High Side Status Register (HSSR).
Current Limitation
Each high side driver has an output current limitation. In
combination with the over-temperature shutdown the highside drivers are protected against over-current and shortcircuit failures.
When the driver operates in the current limitation area, it is
indicated with the bits HS1CL and HS2CL in the HSSR.
Note: If the driver is operating in current limitation mode,
excessive power might be dissipated.
Over-temperature Protection (HS Interrupt)
Both high side drivers are protected against overtemperature. In case of an over-temperature condition both
high side drivers are shut down and the event is latched in the
Interrupt Control Module. The shutdown is indicated as HS
Interrupt in the Interrupt Source Register (ISR).
A thermal shutdown of the high side drivers is indicated by
setting all HSxOP and HSxCL bits simultaneously.
If the bit HSM is set in the Interrupt Mask Register (IMR),
then an interrupt (IRQ) is generated.
A write to the High Side Control Register (HSCR), when
the over-temperature condition is gone, will re-enable the
high side drivers.
High-voltage Shutdown
In case of a high voltage condition and if the high voltage
shutdown is enabled (bit HVSE in the Mode Control Register
(MCR) is set) both high side drivers are shut down.
A write to the High Side Control Register (HSCR), when
the high voltage condition is gone, will re-enable the high side
drivers.
Sleep And Stop Mode
The high side driver can be enabled to operate in Sleep
and Stop mode for cyclic sensing. Also see Table 35,
Operating Modes Overview.
33910
Analog Integrated Circuit Device Data
Freescale Semiconductor
74
MC33910BAC / MC34910BAC
FUNCTIONAL DEVICE OPERATIONS
OPERATIONAL MODES
LIN PHYSICAL LAYER
The LIN bus pin provides a physical layer for single-wire
communication in automotive applications. The LIN physical
layer is designed to meet the LIN physical layer specification
and has the following features:
• LIN physical layer 2.0 compliant
• Slew rate selection
• Over-current shutdown
• Over-temperature shutdown
• LIN pull-up disable in Stop and Sleep modes
• Advanced diagnostics
• LIN dominant voltage level selection
The LIN driver is a low side MOSFET with over-current
and thermal shutdown. An internal pull-up resistor with a
serial diode structure is integrated, so no external pull-up
components are required for the application in a Slave mode.
The fall time from dominant to recessive and the rise time
from recessive to dominant is controlled. The symmetry
between both slopes is guaranteed.
LIN Pin
The LIN pin offers a high susceptibility immunity level from
external disturbance, guaranteeing communication.
INTERRUPT
CONTROL
MODULE
High-voltage
Shutdown
High Side
Interrupt
WAKE-UP
MODULE
LIN
Wake-up
MOD1:2
LSR0:1
LINPE
LDVS
RXONLY
RXSHORT
VS1
LIN – DRIVER
Slope and Slew Rate Control
Over-current Shutdown (interrupt maskable)
Over-temperature Shutdown (interrupt maskable)
TXDOM
LINOT
LINOC
30K
LIN
TXD
SLOPE
CONTROL
WAKE-UP
FILTER
LGND
RXD
RECEIVER
Figure 39. LIN Interface
Slew Rate Selection
LIN Pull-up Disable In Stop and Sleep Mode
The slew rate can be selected for optimized operation at
10.4 and 20 kBit/s as well as a fast baud rate for test and
programming. The slew rate can be adapted with the bits
LSR1:0 in the LIN control register (LINCR). The initial slew
rate is optimized for 20 kBit/s.
To improve performance and for safe behavior in case of
LIN bus short to ground or LIN bus leakage during Low Power
mode the internal pull-up resistor on the LIN pin can be
disconnected by clearing the LINPE bit in the MCR. The bit
LINPE also changes the bus wake-up threshold (VBUSWU).
In case of a LIN bus short to GND, this feature will reduce
the current consumption in Stop and Sleep modes.
33910
75
Analog Integrated Circuit Device Data
Freescale Semiconductor
MC33910BAC / MC34910BAC
FUNCTIONAL DEVICE OPERATIONS
OPERATIONAL MODES
Over-current Shutdown (LIN Interrupt)
The output low side FET is protected against over-current
conditions. In case of an over-current condition (e.g. LIN bus
short to VBAT), the transmitter will not be shut down. The bit
LINOC in the LIN status register (LINSR) is set.
If the bit LINM is set in the interrupt mask register (IMR) an
Interrupt IRQ will be generated.
Over-temperature Shutdown (LIN Interrupt)
The output low side FET is protected against overtemperature conditions. In case of an over-temperature
condition, the transmitter will be shut down and the bit LINOT
in the LIN status register (LINSR) is set.
If the bit LINM is set in the interrupt mask register (IMR) an
Interrupt IRQ will be generated.
The transmitter is automatically re-enabled once the
condition is gone and TXD is high.
A read of the LIN status register (LINSR) with the TXD pin
will re-enable the transmitter.
RXD Short-circuit Detection (LIN Interrupt)
The LIN transceiver has a short-circuit detection for the
RXD output pin. In case of an short-circuit condition, either
5.0 V or ground, the bit RXSHORT in the LIN status register
(LINSR) is set and the transmitter is shutdown.
If the bit LINM is set in the interrupt mask register (IMR) an
interrupt IRQ will be generated.
The transmitter is automatically re-enabled once the
condition is gone (transition on RXD) and TXD is high.
A read of the LIN status register (LINSR) without the RXD
pin short circuit condition will clear the bit RXSHORT.
TXD Dominant Detection (LIN Interrupt)
The LIN transceiver monitors the TXD input pin to detect
stuck in dominant (0 V) condition. In case of a stuck condition
(TXD pin 0V for more than 1 second (typ.)) the transmitter is
shut down and the bit TXDOM in the LIN status register
(LINSR) is set.
If the bit LINM is set in the interrupt mask register (IMR) an
interrupt IRQ will be generated.
The transmitter is automatically re-enabled once TXD is
high.
A read of the LIN status register (LINSR) with the TXD pin
is high will clear the bit TXDOM.
LIN Dominant Voltage Level Selection
The LIN dominant voltage level can be selected by the bit
LDVS in the LIN control register (LINCR).
LIN Receiver Operation Only
While in Normal mode the activation of the RXONLY bit
disables the LIN TX driver. In the case of a LIN error condition
this bit is automatically set. In case a Low Power mode is
selected with this bit set, the LIN wake-up functionality is
disabled, then, in Stop mode, the RXD pin will reflect the state
of the LIN bus.
STOP Mode And Wake-up Feature
During Stop mode operation the transmitter of the physical
layer is disabled. In case the bit LIN-PU was set in the Stop
mode sequence the internal pull-up resistor is disconnected
from VSUP and a small current source keeps the LIN pin in
the recessive state. The receiver is still active and able to
detect wake-up events on the LIN bus line.
A dominant level longer than tPROPWL followed by a rising
edge will generate a wake-up interrupt and will be reported in
the ISR. Also see Figure 32.
SLEEP Mode And Wake-up Feature
During Sleep mode operation the transmitter of the
physical layer is disabled. In case the bit LIN-PU was set in
the Sleep mode sequence the internal pull-up resistor is
disconnected from VSUP and a small current source keeps
the LIN pin in recessive state. The receiver is still active to be
able to detect wake-up events on the LIN bus line.
A dominant level longer than tPROPWL followed by a rising
edge will generate a system wake-up (Reset) and will be
reported in the ISR. Also see Figure 31.
33910
Analog Integrated Circuit Device Data
Freescale Semiconductor
76
MC33910BAC / MC34910BAC
FUNCTIONAL DEVICE OPERATIONS
LOGIC COMMANDS AND REGISTERS
LOGIC COMMANDS AND REGISTERS
SPI AND CONFIGURATION
• MISO — Master-In Slave-Out
• SCLK— Serial Clock
A complete data transfer via the SPI consists of 1 byte.
The master sends 4 bits of address (A3:A0) + 4 bits of control
information (C3:C0) and the slave replies with 3 system
status bits and one not defined bit (VMS,LINS,HSS,n.d.) + 4
bits of status information (S3:S0).
The SPI creates the communication link between a
microcontroller (master) and the 33910.
The interface consists of four pins (see Figure 40):
• CS — Chip Select
• MOSI — Master-Out Slave-In
CS
Register Write Data
MOSI
A3
A2
A1
A0
C3
C2
C1
C0
S1
S0
Register Read Data
MISO
VMS LINS HSS
–
S3
S2
SCLK
Read Data Latch
Rising Edge of SCLK
Change MISO/MISO Output
Write Data Latch
Falling Edge of SCLK
Sample MISO/MISO Input
Figure 40. SPI Protocol
During the inactive phase of the CS (HIGH), the new data
The rising edge of the chip select CS indicates the end of
transfer is prepared.
the transfer and latches the write data (MOSI) into the
register. The CS high forces MISO to the high-impedance
The falling edge of the CS indicates the start of a new data
state.
transfer and puts the MISO in the low-impedance state and
Register reset values are described along with the reset
latches the analog status data (Register read data).
condition. Reset condition is the condition causing the bit to
With the rising edge of the SPI clock (SCLK), the data is
be set to its reset value. The main reset conditions are:
moved to MISO/MOSI pins. With the falling edge of the SPI
- Power-On Reset (POR): level at which the logic is reset
clock (SCLK) the data is sampled by the receiver.
and BATFAIL flag sets.
The data transfer is only valid if exactly 8 sample clock
- Reset mode
edges are present during the active (low) phase of CS.
- Reset done by the RST pin (ext_reset)
33910
77
Analog Integrated Circuit Device Data
Freescale Semiconductor
MC33910BAC / MC34910BAC
FUNCTIONAL DEVICE OPERATIONS
LOGIC COMMANDS AND REGISTERS
SPI REGISTER OVERVIEW
.
Table 36. System Status Register
Adress(A3:A0)
$0 - $F
BIT
Register Name / Read / Write Information
SYSSR - System Status Register
R
7
6
5
4
VMS
LINS
HSS
-
Table 9 summarizes the SPI Register content for Control Information (C3:C0)=W and status information (S3:S0) = R.
Table 37. SPI Register Overview
Adress(A3:A0)
BIT
Register Name / Read / Write Information
3
2
1
0
MCR - Mode Control Register
W
HVSE
LINPE
MOD2
MOD1
VSR - Voltage Status Register
R
VSOV
VSUV
VDDOT
BATFAIL
VSR - Voltage Status Register
R
VSOV
VSUV
VDDOT
BATFAIL
WUCR - Wake-up Control Register
W
-
-
-
L1WE
WUSR - Wake-up Status Register
R
-
-
-
L1
WUSR - Wake-up Status Register
R
-
-
-
L1
LINCR - LIN Control Register
W
LDVS
RXONLY
LSR1
LSR0
LINSR - LIN Status Register
R
RXSHORT
TXDOM
LINOT
LINOC
LINSR - LIN Status Register
R
RXSHORT
TXDOM
LINOT
LINOC
HSCR - High Side Control Register
W
PWMHS2
PWMHS1
HS2
HS1
HSSR - High Side Status Register
R
HS2OP
HS2CL
HS1OP
HS1CL
HSSR - High Side Status Register
R
HS2OP
HS2CL
HS1OP
HS1CL
TIMCR - Timing Control Register
W
CS/WD
WD2
WD1
WD0
CYST2
CYST1
CYST0
WDSR - Watchdog Status Register
R
WDTO
WDERR
WDOFF
WDWO
$B
WDSR - Watchdog Status Register
R
WDTO
WDERR
WDOFF
WDWO
$C
AMUXCR - Analog Multiplexer Control Register
W
L1DS
MX2
MX1
MX0
$D
CFR - Configuration Register
W
HVDD
CYSX8
-
-
IMR - Interrupt Mask Register
W
HSM
-
LINM
VMM
ISR - Interrupt Source Register
R
ISR3
ISR2
ISR1
ISR0
ISR - Interrupt Source Register
R
ISR3
ISR2
ISR1
ISR0
$0
$1
$2
$3
$4
$5
$6
$7
$A
$E
$F
Note: Address $8 and $9 are reserved and must not be used.
33910
Analog Integrated Circuit Device Data
Freescale Semiconductor
78
MC33910BAC / MC34910BAC
FUNCTIONAL DEVICE OPERATIONS
LOGIC COMMANDS AND REGISTERS
REGISTER DEFINITIONS
HSS - High Side Switch Status
System Status Register - SYSSR
The system status register (SYSSR) is always transferred
with every SPI transmission and gives a quick system status
overview. It summarizes the status of the voltage status
register (VSR), LIN status register (LINSR) and the HSSR.
This read-only bit indicates that one or more bits in the
HSSR are set.
1 = High Side Status bit set
0 = None
Table 38. System Status Register
S7
S6
S5
HS1CL
HS1OP
S4
HSS
HS2CL
Read
VMS
LINS
HSS
–.
HS2OP
VMS - Voltage Monitor Status
Figure 43. High Side Status
This read-only bit indicates that one or more bits in the
voltage status register (VSR) are set.
1 = Voltage Monitor bit set
0 = None
VSUV
Figure 41. Voltage Monitor Status
LINS - LIN Status
This read-only bit indicates that one or more bits in the LIN
status register (LINSR) are set.
1 = LIN Status bit set
0 = None
LINOC
TXDOM
C3
C2
C1
C0
Write
HVSE
LINPE
MOD2
MOD1
Reset
Value
1
1
-
-
Reset
Condition
POR
POR
-
-
VMS
VSOV
LINOT
The MCR allows to switch between the operation modes
and to configure the 33910. Writing the MCR will return the
voltage status register (VSR).
Table 39. Mode Control Register - $0
BATFAIL
VDDOT
Mode Control Register - MCR
LINS
RXSHORT
Figure 42. LIN Status
HVSE - High-voltage Shutdown Enable
This write-only bit enables/disables automatic shutdown of
the high side and the low side drivers during a high-voltage
VSOV condition.
1 = automatic shutdown enabled
0 = automatic shutdown disabled
LINPE - LIN pull-up enable.
This write-only bit enables/disables the 30 kΩ LIN pull-up
resistor in Stop and Sleep modes. This bit also controls the
LIN bus wake-up threshold.
1 = LIN pull-up resistor enabled
0 = LIN pull-up resistor disabled
33910
79
Analog Integrated Circuit Device Data
Freescale Semiconductor
MC33910BAC / MC34910BAC
FUNCTIONAL DEVICE OPERATIONS
LOGIC COMMANDS AND REGISTERS
MOD2, MOD1 - Mode Control Bits
These write-only bits select the Operating mode and allow
to clear the watchdog in accordance with Table 38 Mode
Control Bits.
Any access to the MCR or voltage status register (VSR)
will clear the BATFAIL flag.
1 = POR Reset has occurred
0 = POR Reset has not occurred
Table 40. Mode Control Bits
Wake-up Control Register - WUCR
MOD2
MOD1
Description
0
0
Normal Mode
0
1
Stop Mode
1
0
Sleep Mode
1
1
Normal Mode + watchdog Clear
This register is used to control the digital wake-up input.
Writing the wake-up control register (WUCR) will return the
wake-up status register (WUSR).
Table 42. Wake-up Control Register - $2
C3
C2
C1
C0
Voltage Status Register - VSR
Write
0
0
0
L1WE
Returns the status of the several voltage monitors. This
register is also returned when writing to the MCR.
Reset
Value
1
1
1
1
Table 41. Voltage Status Register - $0/$1
Read
S3
S2
S1
S0
VSOV
VSUV
VDDOT
BATFAIL
VSOV - VSUP Over-voltage
This read-only bit indicates an over-voltage condition on
the VS1 pin.
1 = Over-voltage condition.
0 = Normal condition.
VSUV - VSUP Under-voltage
This read-only bit indicates an under-voltage condition on
the VS1 pin.
1 = Under-voltage condition.
0 = Normal condition.
VDDOT - Main Voltage Regulator Over-temperature
Warning
This read-only bit indicates that the main voltage regulator
temperature reached the Over-Temperature Prewarning
Threshold.
1 = Over-temperature prewarning
0 = Normal
BATFAIL - Battery Fail Flag.
This read-only bit is set during power-up and indicates that
the 33910 had a power on reset (POR).
Reset
Condition
POR, Reset mode or ext_reset
L1WE - Wake-up Input Enable
This write-only bit enables/disables the L1 input. In Stop
and Sleep mode the L1WE bit activates the L1 input for wakeup. If the L1 input is selected on the analog multiplexer, the
L1WE is masked to 0.
1 = Wake-up Input enabled.
0 = Wake-up Input disabled.
Wake-up Status Register - WUSR
This register is used to monitor the digital wake-up inputs
and is also returned when writing to the wake-up control
register (WUCR).
Table 43. Wake-up Status Register - $2/$3
S3
S2
S1
S0
-
-
-
L1
Read
L1 - Wake-up input
This read-only bit indicates the status of the L1 input. If the
L1 input is not enabled then the wake-up status will return 0.
After a wake-up form Stop or Sleep mode this bit also
allows to verify the L1 input has caused the wake-up, by first
reading the interrupt status register (ISR) and then reading
the wake-up status register (WUSR).
1 = L1 Wake-up.
0 = L1 Wake-up disabled or selected as analog input.
33910
Analog Integrated Circuit Device Data
Freescale Semiconductor
80
MC33910BAC / MC34910BAC
FUNCTIONAL DEVICE OPERATIONS
LOGIC COMMANDS AND REGISTERS
LIN Control Register - LINCR
LIN Status Register - LINSR
This register controls the LIN physical interface block.
Writing the LIN control register (LINCR) returns the LIN status
register (LINSR).
This register returns the status of the LIN physical
interface block and is also returned when writing to the LIN
control register (LINCR).
Table 44. LIN Control Register - $4
Table 46. LIN Status Register - $4/$5
C3
C2
C1
C0
Write
LDVS
RXONLY
LSR1
LSR0
Reset
Value
0
0
0
0
Reset
Condition
POR, Reset
mode or
ext_reset
POR, Reset mode,
ext_reset or LIN
failure gone*
POR
* LIN failure gone: if LIN failure (over-temp, TXD/RXD short) was set, the flag
resets automatically when the failure is gone.
LDVS - LIN Dominant Voltage Select
This write-only bit controls the LIN Dominant voltage:
1 = LIN Dominant Voltage = VLIN_DOM_1 (1.7 V typ)
0 = LIN Dominant Voltage = VLIN_DOM_0 (1.1 V typ)
RXONLY - LIN Receiver Operation Only
This write-only bit controls the behavior of the LIN
transmitter.
In Normal mode the activation of the RXONLY bit disables
the LIN transmitter. In case of a LIN error condition this bit is
automatically set.
In Stop mode this bit disables the LIN wake-up
functionality and the RXD pin will reflect the state of the LIN
bus.
1 = only LIN receiver active (Normal mode) or LIN wakeup disabled (Stop mode).
0 = LIN fully enabled.
LSRx - LIN Slew-Rate
This write-only bit controls the LIN driver slew-rate in
accordance with Table 45.
Table 45. LIN Slew-Rate Control
LSR1
LSR0
Description
0
0
Normal Slew Rate (up to 20 kb/s)
0
1
Slow Slew Rate (up to 10 kb/s)
1
0
Fast Slew Rate (up to 100 kb/s)
1
1
Reserved
Read
S3
S2
S1
S0
RXSHORT
TXDOM
LINOT
LINOC
RXSHORT - RXD Pin Short Circuit
This read-only bit indicates a short-circuit condition on the
RXD pin (shorted either to 5.0 V or to Ground). The shortcircuit delay must be 8.0 µs worst case to be detected and to
shutdown the driver. To clear this bit, it must be read after the
condition is gone (transition detected on RXD pin). The LIN
driver is automatically re-enabled once the condition is gone.
1 = RXD short circuit condition.
0 = None.
TXDOM - TXD Permanent Dominant
This read-only bit signals the detection of a TXD pin stuck
at dominant (Ground) condition and the resultant shutdown in
the LIN transmitter. This condition is detected after the TXD
pin remains in dominant state for more than 1 second typical
value.
To clear this bit, it must be read after TXD has gone high.
The LIN driver is automatically re-enabled once TXD goes
High.
1 = TXD stuck at dominant fault detected.
0 = None.
LINOT - LIN Driver Over-temperature Shutdown
This read-only bit signals that the LIN transceiver was
shutdown due to over-temperature. The transmitter is
automatically re-enabled after the over-temperature
condition is gone and TXD is high. The LINOT bit is cleared
after SPI read once the condition is gone.
1 = LIN over-temperature shutdown
0 = None
LINOC - LIN Driver Over-current Shutdown
This read-only bit signals an over-current condition
occurred on the LIN pin. The LIN driver is not shutdown but
an IRQ is generated. To clear this bit, it must be read after the
condition is gone.
1 = LIN over-current shutdown
0 = None
33910
81
Analog Integrated Circuit Device Data
Freescale Semiconductor
MC33910BAC / MC34910BAC
FUNCTIONAL DEVICE OPERATIONS
LOGIC COMMANDS AND REGISTERS
High Side Control Register - HSCR
HSxCL - High Side Current Limitation
This register controls the operation of the high side drivers.
Writing to this register returns the High Side Status Register
(HSSR).
This read-only bit indicates that the high side switch is
operating in current Limitation mode.
1 = HSx in current limitation (or thermal shutdown)
0 = Normal
Table 47. High Side Control Register - $6
C3
C2
C1
C0
Write
PWMHS2
PWMHS1
HS2
HS1
Reset
Value
0
0
0
0
Reset
Condition
Timing Control Register - TIMCR
This register is a double purpose register which allows to
configure the watchdog and the cyclic sense periods. Writing
to the TIMCR will also return the WDSR.
Table 49. Timing Control Register - $A
POR, Reset mode, ext_reset, HSx
over-temp or (VSOV & HVSE)
POR
C3
PWMHSx - PWM Input Control Enable
Write
This write-only bit enables/disables the PWMIN input pin
to control the high side switch. The high side switch must be
enabled (HSx bit).
1 = PWMIN input controls HS1 output.
0 = HSx is controlled only by SPI.
HSx - High Side Switch Control.
This write-only bit enables/disables the high side switch.
1 = HSx switch on.
0 = HSx switch off.
High Side Status Register - HSSR
This register returns the status of the high side switch and
is also returned when writing to the HSCR.
Table 48. High Side Status Register - $6/$7
Read
S3
S2
S1
S0
HS2OP
HS2CL
HS1OP
HS1CL
C2
C1
C0
WD2
WD1
WD0
CYST2
CYST1
CYST0
0
0
0
CS/WD
Reset
Value
-
Reset
Condition
-
POR
CS/WD - Cyclic Sense or Watchdog Prescaler Select.
This write-only bit selects which prescaler is being written
to, the cyclic sense prescaler or the watchdog prescaler.
1 = Cyclic Sense Prescaler selected
0 = Watchdog Prescaler select
WDx - Watchdog Prescaler
This write-only bits selects the divider for the watchdog
prescaler and therefore selects the watchdog period in
accordance with Table 50. This configuration is valid only if
windowing watchdog is active.
Table 50. Watchdog Prescaler
High Side thermal shutdown
A thermal shutdown of the high side drivers is indicated by
setting the HSxOP and HSxCL bits simultaneously.
HSxOP - High Side Switch Open-Load Detection
This read-only bit signals that the high side switch is
conducting current below a certain threshold indicating
possible load disconnection.
1 = HSx Open Load detected (or thermal shutdown)
0 = Normal
WD2
WD1
WD0
Prescaler Divider
0
0
0
1
0
0
1
2
0
1
0
4
0
1
1
6
1
0
0
8
1
0
1
10
1
1
0
12
1
1
1
14
33910
Analog Integrated Circuit Device Data
Freescale Semiconductor
82
MC33910BAC / MC34910BAC
FUNCTIONAL DEVICE OPERATIONS
LOGIC COMMANDS AND REGISTERS
CYSTx - Cyclic Sense Period Prescaler Select
This write-only bits selects the interval for the wake-up
cyclic sensing together with the bit CYSX8 in the
configuration register (CFR) (see Configuration Register CFR).
This option is only active if the high side switch is enabled
when entering in Stop or Sleep mode. Otherwise a timed
wake-up is performed after the period shown in Table 51.
Table 51. Cyclic Sense Interval
CYSX8(123)
CYST2
CYST1
CYST0
Interval
X
0
0
0
No Cyclic Sense
0
0
0
1
20 ms
0
0
1
0
40 ms
0
0
1
1
60 ms
0
1
0
0
80 ms
0
1
0
1
100 ms
0
1
1
0
120 ms
0
1
1
1
140 ms
1
0
0
1
160 ms
1
0
1
0
320 ms
1
0
1
1
480 ms
1
1
0
0
640 ms
1
1
0
1
800 ms
1
1
1
0
960 ms
1
1
1
1
1120 ms
Notes
123. bit CYSX8 is located in configuration register (CFR)
WDERR - Watchdog Error
This read-only bit signals the detection of a missing
watchdog resistor. In this condition the watchdog is using the
internal, lower precision timebase. The windowing function is
disabled.
1 = WDCONF pin resistor missing
0 = WDCONF pin resistor not floating
WDOFF - Watchdog Off
This read-only bit signals that the watchdog pin connected
to GND and therefore disabled. In this case watchdog
timeouts are disabled and the device automatically enters
Normal mode out of Reset. This might be necessary for
software debugging and for programming the Flash memory.
1 = Watchdog is disabled
0 = Watchdog is enabled
WDWO - Watchdog Window Open
This read-only bit signals when the watchdog window is
open for clears. The purpose of this bit is for testing. Should
be ignored in case WDERR is High.
1 = Watchdog window open
0 = Watchdog window closed
Analog Multiplexer Control Register - MUXCR
This register controls the analog multiplexer and selects
the divider ration for the L1 input divider.
Table 53. Analog Multiplexer Control Register -$C
Watchdog Status Register
This register returns the watchdog status information and
is also returned when writing to the TIMCR.
Table 52. Watchdog Status Register - $A/$B
Read
1 = Last reset caused by watchdog timeout
0 = None
S3
S2
S1
S0
WDTO
WDERR
WDOFF
WDWO
C3
C2
C1
C0
Write
L1DS
MX2
MX1
MX0
Reset Value
1
0
0
0
Reset Condition
POR
POR, Reset mode or ext_reset
L1DS - L1 Analog Input Divider Select
WDTO - Watchdog Time Out
This read-only bit signals the last reset was caused by
either a watchdog timeout or by an attempt to clear the
watchdog within the window closed.
Any access to this register or the TIMCR will clear the
WDTO bit.
This write-only bit selects the resistor divider for the L1
analog input. Voltage is internally clamped to VDD.
0 = L1 Analog divider: 1
1 = L1 Analog divider: 3.6 (typ.)
33910
83
Analog Integrated Circuit Device Data
Freescale Semiconductor
MC33910BAC / MC34910BAC
FUNCTIONAL DEVICE OPERATIONS
LOGIC COMMANDS AND REGISTERS
MXx - Analog Multiplexer Input Select
These write-only bits selects which analog input is
multiplexed to the ADOUT0 pin according to Table 54.
When disabled or when in Stop or Sleep mode, the output
buffer is not powered and the ADOUT0 output is left floating
to achieve lower current consumption.
Table 54. Analog Multiplexer Channel Select
MX2
MX1
MX0
Meaning
0
0
0
Disabled
0
0
1
Reserved
0
1
0
Die Temperature Sensor
0
1
1
VSENSE input
1
0
0
L1 input
1
0
1
Reserved
1
1
0
Reserved
1
1
1
Reserved
Writing to the interrupt mask register (IMR) will return the
ISR.
Table 56. Interrupt Mask Register - $E
C3
C2
C1
C0
Write
HSM
-.
LINM
VMM
Reset Value
1
1
1
1
Reset Condition
POR
HSM - High Side Interrupt Mask
This write-only bit enables/disables interrupts generated in
the high side block.
1 = HS Interrupts Enabled
0 = HS Interrupts Disabled
LINM - LIN Interrupts Mask
Configuration Register - CFR
This register controls the cyclic sense timing multiplier.
Table 55. Configuration Register - $D
C3
C2
C1
C0
Write
0
CYSX8
0
0
Reset
Value
0
0
0
0
Reset
Condition
POR, Reset
mode or
ext_reset
POR
POR
POR
HVDD - Hall Sensor Supply Enable
This write-only bit enables/disables the state of the hall
sensor supply.
1 = HVDD on
0 = HVDD off
CYSX8 - Cyclic Sense Timing x 8
This write-only bit influences the Cyclic Sense period as
shown in Table 51.
1 = Multiplier enabled
0 = None
This write-only bit enables/disables interrupts generated in
the LIN block.
1 = LIN Interrupts Enabled
0 = LIN Interrupts Disabled
VMM - Voltage Monitor Interrupt Mask
This write-only bit enables/disables interrupts generated in
the voltage monitor block. The only maskable interrupt in the
voltage monitor block is the VSUP over-voltage interrupt.
1 = Interrupts Enabled
0 = Interrupts Disabled
Interrupt Source Register - ISR
This register allows the MCU to determine the source of
the last interrupt or wake-up respectively. A read of the
register acknowledges the interrupt and leads IRQ pin to
high, in case there are no other pending interrupts. If there
are pending interrupts, IRQ will be driven high for 10µs and
then be driven low again.
This register is also returned when writing to the interrupt
mask register (IMR).
Table 57. Interrupt Source Register - $E/$F
Read
S3
S2
S1
S0
ISR3
ISR2
ISR1
ISR0
Interrupt Mask Register - IMR
ISRx - Interrupt Source Register
This register allow to mask some of interrupt sources. The
respective flags within the ISR will continue to work but will
not generate interrupts to the MCU. The 5.0 V Regulator
over-temperature prewarning interrupt and under-voltage
(VSUV) interrupts can not be masked and will always cause
an interrupt.
These read-only bits indicate the interrupt source following
Table 58. If no interrupt is pending than all bits are 0.
In case more than one interrupt is pending, than the
interrupt sources are handled sequentially multiplex.
33910
Analog Integrated Circuit Device Data
Freescale Semiconductor
84
MC33910BAC / MC34910BAC
FUNCTIONAL DEVICE OPERATIONS
LOGIC COMMANDS AND REGISTERS
Table 58. Interrupt Sources
Interrupt Source
ISR3 ISR2 ISR1 ISR0
Priority
none maskable
maskable
no interrupt
no interrupt
none
L1 wake-up from Stop mode-
highest
HS interrupt (Over-temperature)
0
0
0
0
0
0
0
1
0
0
1
0
-
0
0
1
1
-
0
1
0
0
0
1
0
1
0
1
1
0
Reserved
LIN interrupt (RXSHORT, TXDOM, LIN OT, LIN
OC) or LIN wake-up
Voltage monitor interrupt
Voltage monitor interrupt
(Low-voltage and VDD over-temperature)
(High-voltage)
-
Forced wake-up
lowest
33910
85
Analog Integrated Circuit Device Data
Freescale Semiconductor
MC33910BAC / MC34910BAC
TYPICAL APPLICATIONS
LOGIC COMMANDS AND REGISTERS
TYPICAL APPLICATIONS
The 33910 can be configured in several applications. The figure below shows the 33910 in the typical Slave Node Application.
V
BAT
VS2
VS1
D1
C2
C1
C4
Interrupt
Control Module
LVI, HVI, HTI, OCI
IRQ
C3
Internal Bus
VDD
Voltage Regulator
C5
AGND
5V Output Module
VDD
IRQ
HVDD
Hall Sensor Supply
Reset
Control Module
LVR, HVR, HTR, WD,
RST
RST
TIMER
Window
Watchdog Module
PWMIN
R1
High Side Control
Module
HS2
MISO
MOSI
Chip Temp Sense Module
SCLK
Analog Multiplexer
SPI
&
CONTROL
SPI
CS
MCU
HS1
VSENSE
VBAT Sense Module
L1
R2
Analog Input Module
A/D
ADOUT0
Wake Up Module
Digital Input Module
RXD
LIN Physical Layer
SCI
LIN
LIN
TXD
C6
WDCONF
LGND
AGND
PGND
A/D
R7
Typical Component Values:
C1 = 47 µF; C2 = C4 = 100 nF; C3 = 10 µF; C5 = 220 pF
R1 = 10 kΩ; R2 = 20 kΩ-200 kΩ
Recommended Configuration of the not Connected Pins (NC):
Pin 15, 16, 17, 19, 20, 21, 22 = GND
Pin 11 = open (floating)
Pin 28 = this pin is not internally connected and may be used for PCB routing optimization.
33910
Analog Integrated Circuit Device Data
Freescale Semiconductor
86
MC33910BAC / MC34910BAC
PACKAGING
PACKAGE DIMENSIONS
PACKAGING
PACKAGE DIMENSIONS
Important For the most current revision of the package, visit www.Freescale.com and select Documentation, then under
Available Documentation column select Packaging Information.
AC SUFFIX (PB-FREE)
32-PIN LQFP
98ASH70029A
REVISION D
33910
87
Analog Integrated Circuit Device Data
Freescale Semiconductor
MC33910BAC / MC34910BAC
IMPORTANT FOR THE MOST CURRENT REVISION OF THE PACKAGE, VISIT WWW.FREESCALE.COM AND SELECT DOCUMENTATION,
PACKAGE DIMENSIONS (Continued)
AC SUFFIX (PB-FREE)
32-PIN LQFP
98ASH70029A
REVISION D
33910
Analog Integrated Circuit Device Data
Freescale Semiconductor
88
MC33910BAC / MC34910BAC
REVISION HISTORY
REVISION HISTORY
Revision
Date
Description of Changes
1.0
5/2007
•
Initial Release
2.0
9/2007
•
•
•
•
•
Several textual corrections
Page 11: “Analog Output offset Ratio” changed to “Analog Output offset” +/-22mV
Page 11: VSENSE Input Divider Ratio adjusted to 5,0/5,25/5,5
Page 12: Common mode input impedance corrected to 75kΩ
Page 13/15: LIN PHYSICAL LAYER parameters adjusted to final LIN specification release
3.0
9/2007
•
Revision number incremented at engineering request.
4.0
2/2008
•
Changed Functional Block Diagram on page 24.
5.0
11/2008
•
•
•
•
Datasheet updated according to the Pass1.2 silicon version electrical parameters
Add Maximum Rating on IBUS_NO_GND parameter
Added L1, Temperature Sense Analog Output Voltage per characterization(36), Internal Chip Temperature
Sense Gain per characterization at 3 temperatures(36) See Figure 16, Temperature Sense Gain, VSENSE
Input Divider Ratio (RATIOVSENSE=Vsense/Vadout0) per characterization(36), and VSENSE Output Related
Offset per characterization(36) parameters
Added Temperature Sense Gain section
Minor corrections to ESD Capability, (18), Cyclic Sense ON Time from Stop and Sleep Mode(45), Lin Bus Pin
(LIN), Serial Data Clock Pin (SCLK), Master Out Slave In Pin (MOSI), Master In Slave Out Pin (MISO), Digital/
analog Pin (L1), Normal Request Mode, Sleep Mode, LIN Over-temperature Shutdown / TXD Stuck At
Dominant / RXD Short-circuit:, Fault Detection Management Conditions, Lin Physical Layer, LIN Interface,
Over-temperature Shutdown (LIN Interrupt), LIN Receiver Operation Only, SPI Protocol, L1 - Wake-up input
1, LIN Control Register - LINCR, and RXSHORT - RXD Pin Short-circuit
Updated Freescale form and style
•
•
6.0
2/2009
•
Added explanation for pins Not Connected (NC).
7.0
3/2009
•
Changed VBAT_SHIFT and GND_SHIFT maximum from 10% to 11.5% for both parameters on page 13.
3/2010
•
Combined Complete Data sheet for Part Numbers MC33910BAC and MC34910BAC to the back of this data
sheet.
Changed ESD Voltage for Machine Model from ± 200 to ± 150
8.0
•
33910
89
Analog Integrated Circuit Device Data
Freescale Semiconductor
How to Reach Us:
Home Page:
www.freescale.com
Web Support:
http://www.freescale.com/support
USA/Europe or Locations Not Listed:
Freescale Semiconductor, Inc.
Technical Information Center, EL516
2100 East Elliot Road
Tempe, Arizona 85284
1-800-521-6274 or +1-480-768-2130
www.freescale.com/support
Europe, Middle East, and Africa:
Freescale Halbleiter Deutschland GmbH
Technical Information Center
Schatzbogen 7
81829 Muenchen, Germany
+44 1296 380 456 (English)
+46 8 52200080 (English)
+49 89 92103 559 (German)
+33 1 69 35 48 48 (French)
www.freescale.com/support
Japan:
Freescale Semiconductor Japan Ltd.
Headquarters
ARCO Tower 15F
1-8-1, Shimo-Meguro, Meguro-ku,
Tokyo 153-0064
Japan
0120 191014 or +81 3 5437 9125
[email protected]
Asia/Pacific:
Freescale Semiconductor China Ltd.
Exchange Building 23F
No. 118 Jianguo Road
Chaoyang District
Beijing 100022
China
+86 10 5879 8000
[email protected]
For Literature Requests Only:
Freescale Semiconductor Literature Distribution Center
P.O. Box 5405
Denver, Colorado 80217
1-800-441-2447 or +1-303-675-2140
Fax: +1-303-675-2150
[email protected]
Information in this document is provided solely to enable system and
software implementers to use Freescale Semiconductor products. There are
no express or implied copyright licenses granted hereunder to design or
fabricate any integrated circuits or integrated circuits based on the
information in this document.
Freescale Semiconductor reserves the right to make changes without further
notice to any products herein. Freescale Semiconductor makes no warranty,
representation or guarantee regarding the suitability of its products for any
particular purpose, nor does Freescale Semiconductor assume any liability
arising out of the application or use of any product or circuit, and specifically
disclaims any and all liability, including without limitation consequential or
incidental damages. “Typical” parameters that may be provided in Freescale
Semiconductor data sheets and/or specifications can and do vary in different
applications and actual performance may vary over time. All operating
parameters, including “Typicals”, must be validated for each customer
application by customer’s technical experts. Freescale Semiconductor does
not convey any license under its patent rights nor the rights of others.
Freescale Semiconductor products are not designed, intended, or authorized
for use as components in systems intended for surgical implant into the body,
or other applications intended to support or sustain life, or for any other
application in which the failure of the Freescale Semiconductor product could
create a situation where personal injury or death may occur. Should Buyer
purchase or use Freescale Semiconductor products for any such unintended
or unauthorized application, Buyer shall indemnify and hold Freescale
Semiconductor and its officers, employees, subsidiaries, affiliates, and
distributors harmless against all claims, costs, damages, and expenses, and
reasonable attorney fees arising out of, directly or indirectly, any claim of
personal injury or death associated with such unintended or unauthorized
use, even if such claim alleges that Freescale Semiconductor was negligent
regarding the design or manufacture of the part.
Freescale™ and the Freescale logo are trademarks of
Freescale Semiconductor, Inc. All other product or service names
are the property of their respective owners.
© Freescale Semiconductor, Inc. 2009. All rights reserved.
MC33910
Rev. 8.0
3/2010