The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. NEW 0.3 mm Pitch, 1.2 mm above the board, Top and bottom Contact, Back-Flip actuator Flexible Printed Circuit ZIF Connectors FH39 Series ●Small size (39 pos. shown) 1.1mm 13.9 mm ■Features 1. Low-profile 0.3mm pitch connector with top and bottom contact (39 pos .) 3. 45 m m ●Easy FPC insertion actuator Usable via either its top or bottom contact point, this connector achieves enhanced freedom in terms of the product design. 2. High contact reliability thanks to the spring terminal structure Because both top and bottom contact points are springloaded, the contact point adapts to the FPC motion, and high contact reliability is ensured. FPC 3. Delivered with the actuator open FPC can be immediately inserted without the need for the opening of the actuator. 4. Easy FPC insertion ●Completely locked Entry chamfers at all sides of the FPC insertion slot assure correct insertion and positioning of the FPC. 5. Accepts standard FPC thickness 0.2mm thick standard Flexible Printed Circuit (FPC) can be used. This is the only ultra-low profile ZIF connector using standard FPC. 6. Conductive traces on the PCB can run under the connector No exposed contacts on the bottom of the connector. 7. Board placement with automatic equipment Flat upper surface and tape and reel packaging facilitate vacuum pick-up and placement. Standard reel packaging contains 5000 connectors. 8. Halogen-free* (FH39J Series) *As defined by IEC61249-2-21 Br-900ppm maximum, Cl-900ppm maximum, Cl + Br combined-1,500ppm maximum 2010.9 1 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FH39 Series●0.3 mm Pitch, 1.2 mm above the board, Top and bottom Contact, Back-Flip actuator Flexible Printed Circuit ZIF Connectors ■Specifications Current rating 0.2 A Ratings Voltage rating 30 Vrms AC Recommended FPC Operating -55 to +85°C (Note 1) temperature range Operating Relative humidity 90% max. humidity range (No condensation) Storage -10 to +50°C (Note 2) temperature range Storage Relative humidity 90% max. humidity range (No condensation) Thickness: 0.2 ± 0.03 mm, Gold plated contact pads Item Specification 1.Insulation resistance 50 Mø min. 2.Withstanding voltage No flashover or insulation breakdown 100 mø max. 3.Contact resistance * Including FPC and FFC conductor resistance Contact resistance: 100 mø max. 4.Durability No damage, cracks, or parts dislocation No electrical discontinuity of 1µs or longer 5.Vibration Contact resistance: 100 mø max. No damage, cracks, or parts dislocation No electrical discontinuity of 1µs or longer 6.Shock Contact resistance: 100 mø max. No damage, cracks, or parts dislocation Contact resistance: 100 mø max. 7.Humidity Insulation resistance: 50 Mø min. (Steady state) No damage, cracks, or parts dislocation Contact resistance: 100 mø max. 8.Temperature cycle Insulation resistance: 50 Mø min. No damage, cracks, or parts dislocation 9.Resistance to No deformation of components affecting soldering heat performance Conditions 100 V DC 90 Vrms AC / 1 minute 1 mA, AC max (AC: 1kHz) 10 cycles Frequency: 10 to 55 Hz, single amplitude of 0.75 mm, 10 cycles in each of the 3 axis Acceleration of 981m/s2, 6 ms duration, sine half-wave, 3 cycles in each of the 3 axis 96 hours at 40ç and humidity of 90 to 95% Temperature:-55ç➝+15ç to +35ç➝+85ç➝+15ç to +35ç Time: 30➝ 2 to 3 ➝ 30➝ 2 to 3 minutes 5 cycles Reflow: At the recommended temperature profile Manual soldering: 350ç ± 5ç for 5 seconds Note 1: Includes temperature rise caused by current flow. Note 2: The term "storage" refers to products stored for a long period prior to mounting and use. The operating temperature and humidity range covers the non-conducting condition of installed connectors in storage, shipment or during transportation after board mounting. Note 3: Information contained in this catalog represents general requirements for this Series. Contact us for the drawings and specifications for a specific part number shown. ■Materials Part Insulator Contacts Material Finish LCP Color:Beige PA Color:Black Phosphor bronze Metalfittings Remarks Gold plated ----------------- Pure tin reflow plated ----------------- ■Ordering information FH 39 J - 51S - 0.3 SHW (10) 1 2 3 1 Series name:FH 2 Series No.:39 3 Blank :Standard A :Long actuator type J :Halogen-free requirements (Flame retardance UL94V-0). 2 4 5 UL94V-0 6 7 4 Number of positions FH39 :25 to 61 FH39A :67, (71 under planning) FH39J :25 to 51 5 Contact pitch:0.3mm 6 Termination type SHW...SMT horizontal staggered row mount type 7 Plating specifications (10)...Gold plating with nickel barrier The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FH39 Series●0.3 mm Pitch, 1.2 mm above the board, Top and bottom Contact, Back-Flip actuator Flexible Printed Circuit ZIF Connectors ■Connector Dimensions A±0.15 0.3±0.1 B±0.1 3.55±0.2 (0.12) (1.85) 0.6±0.1 Production LOT No. (0.12) 0.6±0.1 C±0.1 B (0.15) (D) (0.6) (3.3) E±0.1 B Detailed drawing [FH39 Series] 1.1±0.1 (1.89) (0.42) (FPC:t0.2mm) (0.42) (FPC:t0.2mm) 1.1±0.1 (1.54) 1 0.1 ) 1 0.47±0.1 0.1±0.15 0˚ 0.1 : : : : 0.3±0.1 0.1±0.15 3.25±0.15 (4.15) (2.1) (1.55) (0.85) (9 Note 1 2 3 4 ˚) (90 (3.85) (2.1) (1.55) (0.85) 0.47±0.1 0.1±0.15 1 B Detailed drawing [FH39A Series] 0.3±0.1 0.1±0.15 3.25±0.15 0.1 1 0.1 The coplanarity of each terminal lead within specified dimension is 0.1 mm Max. Packaged on tape and reel only. Check packaging specification. Slight variations in color of the plastic compounds do not affect form, fit or function of the connector. After reflow, the terminal plating may change color, however this does not represent a quality issue. Part Number FH39-25S-0.3SHW(10) FH39-27S-0.3SHW(10) FH39-29S-0.3SHW(10) FH39-33S-0.3SHW(10) FH39-39S-0.3SHW(10) FH39-45S-0.3SHW(10) FH39-51S-0.3SHW(10) FH39-61S-0.3SHW(10) FH39A-67S-0.3SHW(10) FH39A-71S-0.3SHW(10) FH39J-25S-0.3SHW(10) FH39J-33S-0.3SHW(10) FH39J-39S-0.3SHW(10) FH39J-45S-0.3SHW(10) FH39J-51S-0.3SHW(10) CL No. 580-1806-8-10 580-1805-5-10 580-1807-0-10 580-1803-0-10 580-1800-1-10 580-1802-7-10 580-1801-4-10 580-1808-3-10 580-1809-6-10 Under planning 580-1815-9-10 580-1814-6-10 580-1813-3-10 580-1811-8-10 580-1812-0-10 Number of contacts 25 27 29 33 39 45 51 61 67 71 25 33 39 45 51 A 9.7 10.3 10.9 12.1 13.9 15.7 17.5 20.5 22.3 23.5 9.7 12.1 13.9 15.7 17.5 B 6.6 7.2 7.8 9 10.8 12.6 14.4 17.4 19.2 20.4 6.6 9 10.8 12.6 14.4 C 7.2 7.8 8.4 9.6 11.4 13.2 15 18 19.8 21 7.2 9.6 11.4 13.2 15 All dimensions: mm D E 7.83 9.15 8.43 9.75 9.03 10.35 10.23 11.55 12.03 13.35 13.83 15.15 15.63 16.95 18.63 19.95 20.43 21.75 21.63 22.95 7.83 9.15 10.23 11.55 12.03 13.35 13.83 15.15 15.63 16.95 Tape and reel packaging (5,000 pieces/reel). Order by number of reels. 3 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FH39 Series●0.3 mm Pitch, 1.2 mm above the board, Top and bottom Contact, Back-Flip actuator Flexible Printed Circuit ZIF Connectors Recommended metal mask thickness : t=0.1 0.6±0.05 0.3±0.03 1±0.05 0.35±0.05 (Metal mask:0.35) 0.6±0.05 (Metal mask:0.25) C±0.05 (Metal mask:1) 0.3±0.05 (Metal mask:0.57) 0.67±0.05 (3.65) (0.2) (0.1) 0.3±0.03 (Metal mask:0.25) 0.1±0.05 (Metal mask:0.42) B±0.05 2.48±0.05 0.5±0.05 ■Recommended PCB mounting pattern and metal mask dimensions 0.8±0.05 ■Recommended FPC Dimensions F±0.05 0.3±0.07 2.1±0.1 .2 0.1 0.2 0.3 +0.04 -0.03 3.65MIN (Stiffner) R0 0.2±0.03 (Uncovered area) 0.3±0.02 2.25±0.1 2- 0.3±0.1 0.6±0.02 2.65±0.3 0.3 +0.04 -0.03 1.15±0.1 C±0.03 1.05±0.1 0.3±0.07 0.1±0.02 0.6±0.07 B±0.03 0.6±0.07 * Stiffener dimension should be 3.65mm min., and X dimension should be 0.5mm for improved flexibility of FPC. Part Number FH39-25S-0.3SHW(10) FH39-27S-0.3SHW(10) FH39-29S-0.3SHW(10) FH39-33S-0.3SHW(10) FH39-39S-0.3SHW(10) FH39-45S-0.3SHW(10) FH39-51S-0.3SHW(10) FH39-61S-0.3SHW(10) FH39A-67S-0.3SHW(10) FH39A-71S-0.3SHW(10) FH39J-25S-0.3SHW(10) FH39J-33S-0.3SHW(10) FH39J-39S-0.3SHW(10) FH39J-45S-0.3SHW(10) FH39J-51S-0.3SHW(10) 4 CL No. 580-1806-8-10 580-1805-5-10 580-1807-0-10 580-1803-0-10 580-1800-1-10 580-1802-7-10 580-1801-4-10 580-1808-3-10 580-1809-6-10 Under planning 580-1815-9-10 580-1814-6-10 580-1813-3-10 580-1811-8-10 580-1812-0-10 Number of contacts 25 27 29 33 39 45 51 61 67 71 25 33 39 45 51 B 6.6 7.2 7.8 9 10.8 12.6 14.4 17.4 19.2 20.4 6.6 9 10.8 12.6 14.4 C 7.2 7.8 8.4 9.6 11.4 13.2 15 18 19.8 21 7.2 9.6 11.4 13.2 15 All dimensions: mm F 7.8 8.4 9 10.2 12 13.8 15.6 18.6 20.4 21.6 7.8 10.2 12 13.8 15.6 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FH39 Series●0.3 mm Pitch, 1.2 mm above the board, Top and bottom Contact, Back-Flip actuator Flexible Printed Circuit ZIF Connectors ■Recommended FPC construction 1. Using Single-sided FPC FPC : Flexible Printed Circuit Material Name Material (25) (25) Covering film layer Cover adhesive Polyimide Surface treatment 0.2µm thick gold plated over 1 to 5µm nickel underplating Copper foil Cu 1oz Base adhesive Thermosetting adhesive 25 Base film Polyimide 25 1 mil thick. 3 35 1 mil thick Reinforcement material adhesive Thermosetting adhesive 40 Stiffener 75 Polyimide 3 mil thick 203 Total 2. Using Double-sided FPC Material Thickness (µm) FPC : Flexible Printed Circuit Material Name Covering film layer Material Polyimide 1 mil thick. Material Thickness (µm) (25) (25) Cover adhesive Surface treatment 0.2µm thick gold plated over 1 to 5µm nickel underplating Through-hole copper Cu 15 Copper foil Cu 1/2oz 18 Base adhesive Thermosetting adhesive 18 Base film Polyimide 25 Base adhesive Thermosetting adhesive Copper foil Cu 1/2oz Cover adhesive Thermosetting adhesive 25 Covering film layer Polyimide 1 mil thick. 25 Reinforcement material adhesive Thermosetting adhesive 25 Stiffener Polyimide 1 mil thick 3 mil thick Total 3 18 (18) 25 197 * To prevent release of the FPC due to its bending, use of the double sided FPC with copper foil on the back side is NOT RECOMMENDED. 3. Precautions 1: This specification is a recommendation for the construction of the FH39 Series FPC (t=0.2±0.05). 2: For details about the construction, please contact the FPC manufacturers. 5 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FH39 Series●0.3 mm Pitch, 1.2 mm above the board, Top and bottom Contact, Back-Flip actuator Flexible Printed Circuit ZIF Connectors ■Packaging Specification ●Embossed Carrier Tape Dimensions (Tape width to 24mm max.) 4±0.1 2±0.15 8±0.1 (0.3) 1.5 1.75±0.1 (2.1:FH39 series) (2.4:FH39A series) .1 +0 0 (K) G±0.3 J±0.1 Ø Flat surface, for placement with automatic equipment. (4.65) Unreeling direction ●Embossed Carrier Tape Dimensions (Tape width 32mm min.) 1.5 1.75±0.1 (1.85) .1 +0 0 H±0.1 1.7 +0.15 0 1.5 +0.1 0 3) ●Reel Dimensions (Ø80) (Ø380) (Ø1 (L: INSIDE) (M: OUTSIDE) 6 G±0.3 (K) J±0.1 Ø The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FH39 Series●0.3 mm Pitch, 1.2 mm above the board, Top and bottom Contact, Back-Flip actuator Flexible Printed Circuit ZIF Connectors All dimensions: mm L M Part Number CL No. Number of contacts G H J K FH39-25S-0.3SHW(10) 580-1806-8-10 25 24 --- 11.5 11 25.4 29.4 FH39-27S-0.3SHW(10) 580-1805-5-10 27 24 --- 11.5 11.6 25.4 29.4 FH39-29S-0.3SHW(10) 580-1807-0-10 29 24 --- 11.5 12.2 25.4 29.4 FH39-33S-0.3SHW(10) 580-1803-0-10 33 24 --- 11.5 13.4 25.4 29.4 FH39-39S-0.3SHW(10) 580-1800-1-10 39 24 --- 11.5 15.2 25.4 29.4 FH39-45S-0.3SHW(10) 580-1802-7-10 45 32 28.4 14.2 17 33.4 37.4 FH39-51S-0.3SHW(10) 580-1801-4-10 51 32 28.4 14.2 18.8 33.4 37.4 FH39-61S-0.3SHW(10) 580-1808-3-10 61 44 40.4 20.2 21.8 45.4 49.4 FH39A-67S-0.3SHW(10) 580-1809-6-10 67 44 40.4 20.2 23.6 45.4 49.4 FH39A-71S-0.3SHW(10) Under planning 71 44 40.4 20.2 24.8 45.4 49.4 FH39J-25S-0.3SHW(10) 580-1815-9-10 25 24 --- 11.5 11 25.4 29.4 FH39J-33S-0.3SHW(10) 580-1814-6-10 33 24 --- 11.5 13.4 25.4 29.4 FH39J-39S-0.3SHW(10) 580-1813-3-10 39 24 --- 11.5 15.2 25.4 29.4 FH39J-45S-0.3SHW(10) 580-1811-8-10 45 32 28.4 14.2 17 33.4 37.4 FH39J-51S-0.3SHW(10) 580-1812-0-10 51 32 28.4 14.2 18.8 33.4 37.4 Tape and reel packaging (5,000 pieces/reel). 7 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FH39 Series●0.3 mm Pitch, 1.2 mm above the board, Top and bottom Contact, Back-Flip actuator Flexible Printed Circuit ZIF Connectors ■Temperature Profile MAX 250ç 250 230ç Temperature (ç) 200 200ç 150 150ç 100 50 25ç (60sec.) 90 sec. to 120 sec. Preheating 0 Start Time (Seconds) 8 (60sec.) Soldering HRS test condition Solder method :Reflow, IR/hot air Environment :Room air Solder composition :Paste, 96.5%Sn/3.0%Ag/0.5%Cu (Senju Metal Industry, Co., Ltd.'s Part Number:M705-221CM5-32-10.5) Test board :Glass epoxy 25mm∞50mm∞0.8mm thick Land dimensions :0.3mm∞0.5mm, 0.3mm∞0.67mm Metal mask :0.25∞0.42, 0.25∞0.57∞0.1mm thick The temperature profiles shown are based on the above conditions. In individual applications the actual temperature may vary, depending on solder paste type, volume / thickness and board size / thickness. Consult your solder paste and equipment manufacturer for specific recommendations. The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FH39 Series●0.3 mm Pitch, 1.2 mm above the board, Top and bottom Contact, Back-Flip actuator Flexible Printed Circuit ZIF Connectors ■Connector Operation and Precautions Operation Exercise care when handling connectors. Follow recommendations given below. 1. As delivered Delivered with the actuator open. There is no need to operate the actuator prior to the insertion of the FPC. The actuator is open when delivered in the embossed tape packaging 2. FPC insertion Align the FPC perpendicular with the connector and insert it firmly all the way. 9 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FH39 Series●0.3 mm Pitch, 1.2 mm above the board, Top and bottom Contact, Back-Flip actuator Flexible Printed Circuit ZIF Connectors Operation 3. Locking After FPC/FFC insertion, rotate the actuator down to a full stop, pushing it at the center. Rotate Excessive force after the actuator is already closed Push at the center of the actuator. Do NOT close at the ends. 4. FPC removal (Lock release) Carefully rotate the actuator up to 90°, lifting it at the center. Rotate (lift) Do not attempt to open more than 90° Lift at the center Do not open (lift) at one end. * The actuator opens by rotating it in the direction OPPOSITE to the direction of the insertion of the FPC. DO NOT attempt to open it from the same side as the insertion of the FPC. 10 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FH39 Series●0.3 mm Pitch, 1.2 mm above the board, Top and bottom Contact, Back-Flip actuator Flexible Printed Circuit ZIF Connectors Precautions when mounting connectors on the PCB ◆Handling before mounting on PCB Insertion of the FPC or operation of the actuator prior to mounting on the PCB is NOT RECOMMENDED. ◆PC board warpage Minimize the warpage as much as possible. The connector is straight within 0.1 mm max. Make sure that the mounting area flatness can accept the connector terminals without causing any failure of the solder joints. ◆Forces on the board ◆When braking the large PC board into individual boards exercise care NOT to damage the installed connectors. ◆When attaching the boards or other components with the screws make sure that any stresses will NOT cause board deflections affecting the mounting areas of the connector. Connector PCB Other precautions ◆When hand soldering: Do not perform hand soldering with the FPC inserted in the connector. • Do not apply excessive heat or touch the soldering iron anywhere other than the connector leads. • Do not use excessive amount of solder or flux compounds. Operation of the actuator or contacts may be affected by excessive amounts of solder or flux compounds. 11