The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. 0.3 mm Pitch, 0.65 mm above the board, Top Contact, Back-Flip actuator Flexible Printed Circuit ZIF Connectors FH42 Series Height 0.65mm 3 .0 8m m 0.65mm 11.4mm (31pos.) Figure. 1 ■Features Simple FPC insertion 1.L ow-profile and space-saving 0.3mm pitch, top contact point, connector actuator A top contact point type connector, low-profile and spacesaving design, with 0.65mm height and 3.55mm depth (implementation depth: 3.08mm). 2.FPC retention secured, despite the low profile Improved FPC horizontal retention by reinforcing the clasp temporary retention mechanism. FPC 3.Delivered with the actuator open FPC can be immediately inserted without the need for the opening of the actuator. 4.Favorable FPC insertion, despite the low profile - The unique clasp form means an audible click when the FPC goes over the clasp, while also preventing incorrect (diagonal) insertion of FPC. - D espite the temporar y retention mechanism of the reinforcing clasp, horizontal insertion of FPC is possible. Figure. 2 Lock 5.Accepts standard FPC thickness 0.12mm thick standard Flexible Printed Circuit (FPC) can be used. This is the only ultra-low profile ZIF connector using standard FPC. 6.Conductive traces on the PCB can run under the connector No exposed contacts on the bottom of the connector. 7.Board placement with automatic equipment Flat upper surface and tape and reel packaging facilitate vacuum pick-up and placement. Standard reel packaging contains 5,000 connectors. 8.Halogen-free Figure. 3 * *As defined by IEC61249-2-21 Br-900ppm maximum, Cl-900ppm maximum, Cl + Br combined-1,500ppm maximum 2010.9 1 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FH42 Series●0.3 mm Pitch, 0.65 mm above the board, Top Contact, Back-Flip actuator Flexible Printed Circuit ZIF Connectors ■Specifications Current rating 0.2 A(Note1) Operating temperature range:-55 to +85°C (Note 2) Storage temperature range:-10 to +50°C (Note 3) Voltage rating 30 Vrms AC Operating humidity range:Relative humidity 90% max. (No condensation) Storage humidity range:Relative humidity 90% max. (No condensation) Ratings Recommended FPC Thickness 0.12 +/- 0.02 mm, Gold plated contact pads Item Specification Conditions 1.Insulation resistance 50 Mø min. 100 V DC 2.Withstanding voltage No flashover or insulation breakdown 90 Vrms AC / one minute 3.Contact resistance 200 mø max. * Including FPC and FFC conductor resistance 1 mA, AC max (AC: 1kHz) 4.Durability Contact resistance: 200 mø max. No damage, cracks, or parts dislocation 10 cycles 5.Vibration No electrical discontinuity of 1μs or longer Contact resistance: 200 mø max. No damage, cracks, or parts dislocation Frequency: 1 0 to 55 Hz, single amplitude of 0.75mm, 10 cycles in each of the 3 axis 6.Shock No electrical discontinuity of 1μs or longer Contact resistance: 200 mø max. No damage, cracks, or parts dislocation Acceleration of 981m/s2, 6 ms duration, sine halfwave, 3 cycles in each of the 3 axis 7.Humidity (Steady state) Contact resistance: 200 mø max. Insulation resistance: 50 Mø min. No damage, cracks, or parts dislocation 96 hours at 40°C and humidity of 90 to 95% 8.Temperature cycle Contact resistance: 200 mø max. Insulation resistance: 50 Mø min. No damage, cracks, or parts dislocation Temperature : -55°C → +15°C to +35°C → +85°C → +15°C to +35°C Time: 30 → 2 to 3 → 30 → 2 to 3 minutes 5 cycles 9.Resistance to soldering heat No deformation of components affecting performance Reflow: At the recommended temperature profile Manual soldering: 350°C ±10°C for 5 seconds Note 1: When passing the current through all of the contacts, use 70% of the rated current. Note 2: Includes temperature rise caused by current flow. Note 3: The term "storage" refers to products stored for a long period prior to mounting and use. The operating temperature and humidity range covers the non-conducting condition of installed connectors in storage, shipment or during transportation after board mounting. Note 4: Information contained in this catalog represents general requirements for this Series. Contact us for the drawings and specifications for a specific part number shown. ■Materials Part Material Finish Remarks LCP Color:Beige UL94V-0 PA Color:Black UL94HB Gold plated --------- Pure tin reflow plated --------- Insulator Contacts Phosphor bronze Metalfittings ■Ordering information FH 42 − 31S − 0.3 SHW (10) 1 2 3 1Series name : FH 2Series No. : 41 3Number of positioms : 19,31,41 4Contact pitch : 0.3mm 2 4 5 6 5Contact type SHW : SMT horizontal staggered mounting 6Plating specifications (10)…Gold plating with nickel barrier The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FH42 Series●0.3 mm Pitch, 0.65 mm above the board, Top Contact, Back-Flip actuator Flexible Printed Circuit ZIF Connectors ■Connector Dimensions [FH42 Series] A±0.15 0.3±0.1 B±0.1 (0.1) 0.6±0.1 (0.1) (0.15) 0.6±0.1 C±0.1 D±0.1 B (E) 1 0.1 (0.1) FPC:0.12 (1.45) (1.13) (0.53) (0.27) (1.11) 0.65±0.04 Detail drawing 1 0.1 1 0.1 0.355±0.1 0.28±0.1 0.5±0.1 3.23±0.15 3.08±0.15 (3.55) Note 1. The coplanarity of each terminal lead within specified dimension is 0.1 mm Max. 2. Packaged on tape and reel only. Check packaging specification. 3. Slight variations in color of the plastic compounds do not affect form, fit or function of the connector. 4. After reflow, the terminal plating may change color, however this does not represent a quality issue. Unit : mm CL No. Number of contacts A B C D E FH42-19S-0.3SHW(10) Part Number 0580-2305-8-10 19 7.8 4.8 5.4 6.55 7.28 FH42-31S-0.3SHW(10) 0580-2301-7-10 31 11.4 8.4 9 10.15 10.88 FH42-41S-0.3SHW(10) 0580-2304-5-10 41 14.4 11.4 12 13.15 13.88 Note1.Tape and reel packaging (5,000 pieces/reel). Order by number of reels. 3 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FH42 Series●0.3 mm Pitch, 0.65 mm above the board, Top Contact, Back-Flip actuator Flexible Printed Circuit ZIF Connectors (Recommendad metal mask thickness:t=0.1) 0.3±0.03(Land pattern) 0.3±0.01(Metal mask) B±0.05 (0.3) (0.2) 0.28±0.03(Land pattern) 0.26±0.01(Metal mask) 0.76±0.05(Land) 0.76±0.03(Metal mask) 0.6±0.05 (0.37) (0.2) 0.24±0.05 0.3±0.05 0.9±0.05(Land pattern) 0.73±0.03(Metal mask) 3.48±0.05 0.6±0.05(Land pattern) 0.48±0.03(Metal mask) ■Recommended PCB mounting pattern and metal mask dimensions 0.6±0.05 0.28±0.03(Land pattern) 0.26±0.01(Metal mask) C±0.05 0.575±0.05 0.575±0.05 ■Recommended FPC Dimensions 0.12±0.02 F±0.05 0.925±0.07 C±0.03 0.925±0.07 0.3±0.03 5 ±0.0 G±0.05 R0.2 5 R0.2 (0.2) ±0.0 (0.2) 2.7±0.3(stiffener) M 5 .0 ±0 05 . .2 R0 2±0 . R0 R0.3 1 R0. 0.3±0.03 (0.15) 1.47±0.1 1.9±0.3 R0.2 0.13±0.1 0.75±0.1 0.93±0.05 0.7±0.1 0.3±0.03 0.1±0.02 R0.46±0.05 (0.6) 1.53±0.05 (0.35) R0 R0. .3± 13 0.0 5 0.3±0.02 H±0.1 *Stiffener dimension should be 2.4mm min., and M dimension should be 0.5mm for improved flexibility of FPC. Unit : mm Part Number 4 CL No. Number of contacts B C F G H FH42-19S-0.3SHW(10) 0580-2305-8-10 19 4.8 5.4 7.25 6.22 8.2 FH42-31S-0.3SHW(10) 0580-2301-7-10 31 8.4 9 10.85 9.82 11.8 FH42-41S-0.3SHW(10) 0580-2304-5-10 41 11.4 12 13.85 12.82 14.8 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FH42 Series●0.3 mm Pitch, 0.65 mm above the board, Top Contact, Back-Flip actuator Flexible Printed Circuit ZIF Connectors ■Recommended FPC construction 1. Using Single-sided FPC FPC : Flexible Printed Circuit Material Name Covering film layer Material Polyimide 1 mil thick. Cover adhesive Material Thickness (μm) (25) (25) Surface treatment 0.2μm thick gold plated over 1 to 5μm nickel underplating Copper foil Cu 1/2 oz Base adhesive Thermosetting adhesive 3.2 18 Non-adhesive type Base film Polyimide 1 mil thick 25 Reinforcement material adhesive Thermosetting adhesive 35 Stiffener Polyimide 2 mil thick 40 Total 131.2 2. Precautions 1. This specification is a recommendation for the construction of the FH42 Series FPC and FFC (t=0.12 ±0.02). 2. For details about the construction, please contact the FPC/FFC manufacturers. 5 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FH42 Series●0.3 mm Pitch, 0.65 mm above the board, Top Contact, Back-Flip actuator Flexible Printed Circuit ZIF Connectors ■Packaging Specification 3.05±0.1 (2) .1 +00 .5 CL (M) Ø1 (0.62) (1.105) (0.7) (4.33) (1.9) Unreeling direction 1.75±0.1 ●Embossed Carrier Tape Dimensions (Tape width 32mm min.) (1.31) (0.3) J±0.2 8±0.1 1.75±0.1 4±0.1 (1.31) (0.3) L±0.1 ●Embossed Carrier Tape Dimensions (Tape width to 24mm max.) .1 +00 .5 Ø1 1.5 +0.1 0 J±0.2 K±0.1 1.7 +0.15 0 (M) L±0.1 CL 3 ●Reel Dimensions Ø80 Ø380 Ø1 (L: INSIDE) (M: OUTSIDE) Unit : mm Part Number CL No. J K L M N P FH42-19S-0.3SHW(10) 0580-2305-8-10 19 24 ----- 11.5 9.3 25.4 29.4 FH42-31S-0.3SHW(10) 0580-2301-7-10 31 24 ----- 11.5 12.9 25.4 29.4 FH42-41S-0.3SHW(10) 0580-2304-5-10 41 24 ----- 11.5 15.9 25.4 29.4 Tape and reel packaging (5,000 pieces/reel). 6 Number of contacts The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FH42 Series●0.3 mm Pitch, 0.65 mm above the board, Top Contact, Back-Flip actuator Flexible Printed Circuit ZIF Connectors ■Temperature Profile ●Using Lead-free Solder Paste MAX 250ç 250 230ç Temperature (ç) 200 200ç 150 100 50 0 (60sec.) 90 sec. to 120 sec. Preheating Start Solder method :Reflow, IR/hot air Environment :Room air Solder composition :Paste, 96.5%Sn/3.0%Ag/0.5%Cu (Senju Metal Industry, Co., Ltd.'s Part Number:M705-GRN360-K2-V) Test board :Glass epoxy 25mm×50mm×0.8mm thick Land dimensions :0.28mm×0.6mm,0.28mm×0.9mm Metal mask :0.26×0.48,0.26×0.73×0.1mm thick 150ç 25ç HRS test condition (60sec.) soldering The temperature profiles shown are based on the above conditions. In individual applications the actual temperature may vary, depending on solder paste type, volume / thickness and board size / thickness. Consult your solder paste and equipment manufacturer for specific recommendations. Time(Seconds) 7 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FH42 Series●0.3 mm Pitch, 0.65 mm above the board, Top Contact, Back-Flip actuator Flexible Printed Circuit ZIF Connectors ■Connector Operation and Precautions Operation Exercise care when handling connectors. Follow recommendations given below. 1. As delivered 1Delivered with the actuator open. There is no need to operate the actuator prior to the insertion of the FPC. The actuator is open when delivered in the embossed tape packaging 2. FPC insertion (Top contact) 1Make sure that the conductive pads are facing up. 2Align the FPC perpendicular with the connector and insert it firmly all the way. *For the bottom contact, reverse. FPC conductive pads are facing up 3. FPC correct insertion verification (Top contact) A visual comparison of the edge of the housing opening and the FPC pattern boundary will prevent diagonal insertion and partial insertion errors. cutout(housing) FPC tab metal fittings Correct insertion 8 Diagonal insertion Partial insertion The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FH42 Series●0.3 mm Pitch, 0.65 mm above the board, Top Contact, Back-Flip actuator Flexible Printed Circuit ZIF Connectors Operation 4. Locking 1After FPC/FFC insertion, rotate the actuator down to a full stop, pushing it at the center. Rotate Excessive force after the actuator is already closed Push at the center of the actuator. Do NOT close at the ends. 5. FPC removal (Lock release) Carefully rotate the actuator up to 90°, lifting it at the center. Rotate (lift) Do not attempt to open more than 90° Lift at the center Do not open (lift) at one end. イメージ * The actuator opens by rotating it in the direction OPPOSITE to the direction of the insertion of the FPC. DO NOT attempt to open it from the same side as the insertion of the FPC. 9 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FH42 Series●0.3 mm Pitch, 0.65 mm above the board, Top Contact, Back-Flip actuator Flexible Printed Circuit ZIF Connectors Precautions when mounting connectors on the PCB ◆Handling before mounting on PCB Insertion of the FPC or operation of the actuator prior to mounting on the PCB is NOT RECOMMENDED. ◆PC board warpage Minimize the warpage as much as possible. The connector is straight within 0.1 mm max. Make sure that the mounting area flatness can accept the connector terminals without causing any failure of the solder joints. ◆Forces on the board ◆When braking the large PC board into individual boards exercise care NOT to damage the installed connectors. ◆When attaching the boards or other components with the screws make sure that any stresses will NOT cause board deflections affecting the mounting areas of the connector Connector PCB Other precautions ◆When hand soldering: Do not perform hand soldering with the FPC inserted in the connector. • Do not apply excessive heat or touch the soldering iron anywhere other than the connector leads. • Do not use excessive amount of solder or flux compounds. Operation of the actuator or contacts may be affected by excessive amounts of solder or flux compounds. 10