74LVQ125 LOW VOLTAGE QUAD BUS BUFFERS (3-STATE) ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ HIGH SPEED: tPD = 5 ns (TYP.) at VCC = 3.3 V COMPATIBLE WITH TTL OUTPUTS LOW POWER DISSIPATION: ICC = 4 µA (MAX.) at TA=25°C LOW NOISE: VOLP = 0.3V (TYP.) at VCC = 3.3V 75Ω TRANSMISSION LINE DRIVING CAPABILITY SYMMETRICAL OUTPUT IMPEDANCE: |IOH| = IOL = 12mA (MIN) at VCC = 3.0 V PCI BUS LEVELS GUARANTEED AT 24 mA BALANCED PROPAGATION DELAYS: tPLH ≅ tPHL OPERATING VOLTAGE RANGE: VCC(OPR) = 2V to 3.6V (1.2V Data Retention) PIN AND FUNCTION COMPATIBLE WITH 74 SERIES 125 IMPROVED LATCH-UP IMMUNITY DESCRIPTION The 74LVQ125 is a low voltage CMOS QUAD BUS BUFFERS fabricated with sub-micron silicon gate and double-layer metal wiring C2MOS SOP TSSOP Table 1: Order Codes PACKAGE T&R SOP TSSOP 74LVQ125MTR 74LVQ125TTR technology. It is ideal for low power and low noise 3.3V applications. The device requires the same 3-STATE control input G to be set high to place the output in to the high impedance state. All inputs and outputs are equipped with protection circuits against static discharge, giving them 2KV ESD immunity and transient excess voltage. Figure 1: Pin Connection And IEC Logic Symbols July 2004 Rev. 5 1/12 74LVQ125 Figure 2: Input And Output Equivalent Circuit Table 2: Pin Description PIN N° SYMBOL 1, 4, 10, 13 2, 5, 9, 12 3, 6, 8, 11 7 1G to 4G 1A to 4A 1Y to 4Y GND VCC 14 NAME AND FUNCTION Output Enable Inputs Data Inputs Data Outputs Ground (0V) Positive Supply Voltage Table 3: Truth Table A G Y X L H H L L Z L H X : Don‘t Care Z : High Impedance Table 4: Absolute Maximum Ratings Symbol VCC Parameter Supply Voltage Value Unit -0.5 to +7 V VI DC Input Voltage -0.5 to VCC + 0.5 V VO DC Output Voltage -0.5 to VCC + 0.5 ± 20 V mA ± 20 mA IIK DC Input Diode Current IOK DC Output Diode Current IO DC Output Current ICC or IGND DC VCC or Ground Current Storage Temperature Tstg TL Lead Temperature (10 sec) ± 50 mA ± 200 mA -65 to +150 °C 300 °C Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is not implied Table 5: Recommended Operating Conditions Symbol VCC Parameter Unit 2 to 3.6 V VI Input Voltage 0 to VCC V VO Output Voltage Top Operating Temperature dt/dv Input Rise and Fall Time VCC = 3.0V (note 2) 1) Truth Table guaranteed: 1.2V to 3.6V 2) VIN from 0.8V to 2V 2/12 Value Supply Voltage (note 1) 0 to VCC V -55 to 125 °C 0 to 10 ns/V 74LVQ125 Table 6: DC Specifications Test Condition Symbol VIH VIL VOH Parameter High Level Input Voltage Low Level Input Voltage High Level Output Voltage TA = 25°C VCC (V) Min. Typ. Max. 2.0 3.0 to 3.6 3.0 Value Low Level Output Voltage 3.0 -55 to 125°C Min. Min. 0.8 IO=-50 µA 2.9 IO=-12 mA 2.58 2.99 2.9 2.9 2.48 2.2 IO=50 µA 0.002 0.1 IO=12 mA 0 0.36 IOZ ICC IOLD IOHD Input Leakage Current High Impedance Output Leakage Current Quiescent Supply Current Dynamic Output Current (note 1, 2) V 0.8 2.48 Unit Max. 2.0 0.8 IO=24 mA II Max. 2.0 IO=-24 mA VOL -40 to 85°C V V 2.2 0.1 0.1 0.44 0.44 0.55 0.55 V 3.6 VI = VCC or GND ± 0.1 ±1 ±1 µA 3.6 VI = VIH or VIL VO = VCC or GND ±0.25 ± 2.5 ± 5.0 µA 3.6 VI = VCC or GND 4 40 40 µA 3.6 VOLD = 0.8 V max 36 25 mA VOHD = 2 V min -25 -25 mA 1) Maximum test duration 2ms, one output loaded at time 2) Incident wave switching is guaranteed on transmission lines with impedances as low as 75Ω Table 7: Dynamic Switching Characteristics Test Condition Symbol VOLP VOLV VIHD VILD Parameter Dynamic Low Voltage Quiet Output (note 1, 2) Dynamic High Voltage Input (note 1, 3) Dynamic Low Voltage Input (note 1, 3) Value TA = 25°C VCC (V) Min. 3.3 -0.8 3.3 Typ. Max. 0.3 0.8 -55 to 125°C Min. Min. Max. Unit Max. -0.3 2 CL = 50 pF 3.3 -40 to 85°C V 0.8 1) Worst case package. 2) Max number of outputs defined as (n). Data inputs are driven 0V to 3.3V, (n-1) outputs switching and one output at GND. 3) Max number of data inputs (n) switching. (n-1) switching 0V to 3.3V. Inputs under test switching: 3.3V to threshold (VILD), 0V to threshold (VIHD), f=1MHz. 3/12 74LVQ125 Table 8: AC Electrical Characteristics (CL = 50 pF, RL = 500 Ω, Input tr = tf = 3ns) Test Condition Symbol Parameter tPLH tPHL Propagation Delay Time tPLZ tPHZ Output Disable Time tPZL tPZH Output Enable Time tOSLH tOSHL Output To Output Skew Time (note1, 2) Value TA = 25°C VCC (V) -55 to 125°C Min. Min. Typ. Max. 2.7(*) 6.0 10.0 12.0 14.0 (**) 5.0 8.0 9.5 11.0 2.7(*) 6.5 10.5 12.5 14.5 (**) 5.5 8.5 10.0 11.5 2.7(*) 6.8 11.0 12.5 14.0 3.3(**) 5.6 8.0 9.5 11.0 2.7 0.5 0.5 1.0 1.0 1.0 1.0 1.0 1.0 3.3 3.3 Min. -40 to 85°C 3.3(*) Max. Unit Max. ns ns ns ns 1) Skew is defined as the absolute value of the difference between the actual propagation delay for any two outputs of the same device switching in the same direction, either HIGH or LOW (tOSLH = |tPLHm - tPLHn|, tOSHL = |tPHLm - tPHLn|) 2) Parameter guaranteed by design (*) Voltage range is 3.3V ± 0.3V Table 9: Capacitive Characteristics Test Condition Symbol Parameter CIN Input Capacitance COUT Output Capacitance Power Dissipation Capacitance (note 1) CPD Value TA = 25°C VCC (V) Min. Typ. Max. -40 to 85°C -55 to 125°C Min. Min. Max. Unit Max. 3.3 4 pF 3.3 8 pF 19 pF 3.3 fIN = 10MHz 1) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. ICC(opr) = CPD x VCC x fIN + ICC/4 (per gate) 4/12 74LVQ125 Figure 3: Test Circuit TEST SWITCH tPLH, tPHL Open tPZL, tPLZ 2VCC tPZH, tPHZ Open CL = 50pF or equivalent (includes jig and probe capacitance) RL = R1 = 500Ω or equivalent RT = ZOUT of pulse generator (typically 50Ω) Figure 4: Waveform - Propagation Delays (f=1MHz; 50% duty cycle) 5/12 74LVQ125 Figure 5: Waveform - Output Enable And Disable Time (f=1MHz; 50% duty cycle) 6/12 74LVQ125 SO-14 MECHANICAL DATA DIM. mm. MIN. TYP inch MAX. MIN. TYP. MAX. A 1.35 1.75 0.053 0.069 A1 0.1 0.25 0.004 0.010 A2 1.10 1.65 0.043 0.065 B 0.33 0.51 0.013 0.020 C 0.19 0.25 0.007 0.010 D 8.55 8.75 0.337 0.344 E 3.8 4.0 0.150 0.157 e 1.27 0.050 H 5.8 6.2 0.228 0.244 h 0.25 0.50 0.010 0.020 L 0.4 1.27 0.016 0.050 k 0° 8° 0° 8° ddd 0.100 0.004 0016019D 7/12 74LVQ125 TSSOP14 MECHANICAL DATA mm. inch DIM. MIN. TYP A MAX. MIN. TYP. MAX. 1.2 A1 0.05 A2 0.8 b 0.047 0.15 0.002 0.004 0.006 1.05 0.031 0.039 0.041 0.19 0.30 0.007 0.012 c 0.09 0.20 0.004 0.0089 D 4.9 5 5.1 0.193 0.197 0.201 E 6.2 6.4 6.6 0.244 0.252 0.260 E1 4.3 4.4 4.48 0.169 0.173 0.176 1 e 0.65 BSC K 0˚ L 0.45 A 0.60 0.0256 BSC 8˚ 0˚ 0.75 0.018 8˚ 0.024 0.030 A2 A1 b e K c L E D E1 PIN 1 IDENTIFICATION 1 0080337D 8/12 74LVQ125 Tape & Reel SO-14 MECHANICAL DATA mm. inch DIM. MIN. A TYP MAX. MIN. 330 MAX. 12.992 C 12.8 D 20.2 0.795 N 60 2.362 T 13.2 TYP. 0.504 22.4 0.519 0.882 Ao 6.4 6.6 0.252 0.260 Bo 9 9.2 0.354 0.362 Ko 2.1 2.3 0.082 0.090 Po 3.9 4.1 0.153 0.161 P 7.9 8.1 0.311 0.319 9/12 74LVQ125 Tape & Reel TSSOP14 MECHANICAL DATA mm. inch DIM. MIN. A MAX. MIN. 330 13.2 TYP. MAX. 12.992 C 12.8 D 20.2 0.795 N 60 2.362 T 10/12 TYP 0.504 22.4 0.519 0.882 Ao 6.7 6.9 0.264 0.272 Bo 5.3 5.5 0.209 0.217 Ko 1.6 1.8 0.063 0.071 Po 3.9 4.1 0.153 0.161 P 7.9 8.1 0.311 0.319 74LVQ125 Table 10: Revision History Date Revision 29-Jul-2004 5 Description of Changes Ordering Codes Revision - pag. 1. 11/12 74LVQ125 Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a registered trademark of STMicroelectronics All other names are the property of their respective owners © 2004 STMicroelectronics - All Rights Reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 12/12