NC7SZ157 TinyLogic® UHS 2-Input Non-Inverting Multiplexer Features Description Broad VCC Operating Range: 1.65V to 5.5V Proprietary Noise/EMI Reduction Circuitry The NC7SZ157 is a single, high performance, 2-to-1 CMOS non-inverting multiplexer from Fairchild’s Ultra® High Speed series of TinyLogic . The device is fabricated with advanced CMOS technology to achieve ultra high speed with high output drive while maintaining low static power dissipation over a broad VCC operating range. The device is specified to operate over the 1.65V to 5.5V VCC operating range. The inputs and outputs are high impedance when VCC is 0V. Inputs tolerate voltages up to 5.5V independent of VCC operating range. Ultra High-Speed Power Down High-Impedance Inputs/Outputs Over-Voltage Tolerance Inputs Facilitate 5V to 3V Translation Ultra-Small MicroPak™ Packages Space-Saving SC70 Package Ordering Information Top Mark Eco Status NC7SZ157P6X ZF7 RoHS 6-Lead SC70, EIAJ SC-88, 1.25mm Wide 3000 Units on Tape & Reel NC7SZ157L6X B9 RoHS 6-Lead MicroPak™, 1.00mm Wide 5000 Units on Tape & Reel NC7SZ157FHX B9 Green 6-Lead, MicroPak2, 1x1mm Body, .35mm Pitch 5000 Units on Tape & Reel Part Number Package Packing Method For Fairchild’s definition of Eco Status, please visit: http://www.fairchildsemi.com/company/green/rohs_green.html. © 2000 Fairchild Semiconductor Corporation NC7SZ157 • Rev. 1.0.2 www.fairchildsemi.com NC7SZ157 — TinyLogic® UHS 2-Input Non-Inverting Multiplexer September 2009 IEEE/IEC Figure 1. Logic Symbol Pin Configurations Figure 2. SC70 (Top View) Figure 3. MicroPak™ (Top Through View) Figure 4. Pin 1 Orientation Notes: 1. AAA represents product code top mark (see Ordering Information). 2. Orientation of top mark determines pin one location. 3. Reading the top mark left to right, pin one is the lower left pin. NC7SZ157 — TinyLogic® UHS 2-Input Non-Inverting Multiplexer Connection Diagrams Pin Definitions Pin # SC70 Pin # MicroPak Name 1 1 I1 Description 2 2 GND 3 3 I0 Data Input 4 4 Z Output 5 5 VCC 6 6 S Data Input Ground Supply Voltage Control Input Function Table Inputs Output S I1 I0 Z = (I0) • (S) + (I1) • (S) L X L L L X H H H L X L H H X H H = HIGH Logic Level L = LOW Logic Level X = Don’t’ Care © 2000 Fairchild Semiconductor Corporation NC7SZ157 • Rev. 1.0.3 www.fairchildsemi.com 2 Stresses exceeding the absolute maximum ratings may damage the device. The device may not function or be operable above the recommended operating conditions and stressing the parts to these levels is not recommended. In addition, extended exposure to stresses above the recommended operating conditions may affect device reliability. The absolute maximum ratings are stress ratings only. Symbol VCC VIN VOUT Parameter Min. Max. Unit Supply Voltage -0.5 7.0 V DC Input Voltage -0.5 7.0 V DC Output Voltage -0.5 7.0 V -50 mA DC Input Diode Current VIN ≤ 0.5V IOK DC Output Diode Current VOUT ≤ -0.5V -50 mA IOUT DC Output Current ±50 mA DC VCC or Ground Current ±50 mA +150 °C IIK ICC or IGND TSTG Storage Temperature Range -65 TJ Junction Temperature Under Bias +150 °C TL Junction Lead Temperature (Soldering, 10 Seconds) +260 °C PD ESD Power Dissipation at +85°C SC70-6 180 MicroPak-6 130 MicroPak2-6 120 Human Body Model, JEDEC:JESD22-A114 4000 Charge Device Model, JEDEC:JESD22-C101 2000 mW V Recommended Operating Conditions NC7SZ157 — TinyLogic® UHS 2-Input Non-Inverting Multiplexer Absolute Maximum Ratings The Recommended Operating Conditions table defines the conditions for actual device operation. Recommended operating conditions are specified to ensure optimal performance to the datasheet specifications. Fairchild does not recommend exceeding them or designing to Absolute Maximum Ratings. Symbol Parameter Conditions Min. Max. Unit Supply Voltage Operating 1.65 5.50 VCC Supply Voltage Data Retention 1.50 5.50 VIN Input Voltage 0 5.5 V Output Voltage 0 VCC V °C VOUT TA tr , tf Operating Temperature Input Rise and Fall Times -40 +85 VCC at 1.8V ± 0.15V, 2.5V ± 0.2V 0 20 VCC at 3.3V ± 0.3V 0 10 VCC at 5.0V ± 0.5V 0 5 SC70-6 θJA Thermal Resistance © 2000 Fairchild Semiconductor Corporation NC7SZ157 • Rev. 1.0.3 V ns/V 350 MicroPak-6 500 MicroPak2-6 560 °C/W www.fairchildsemi.com 3 Symbol Parameter VIH HIGH Level Input Voltage VIL LOW Level Input Voltage VCC TA=+25°C Conditions Min. 0.75VCC 2.30 to 5.50 0.70VCC 0.70VCC 0.25VCC 2.30 to 5.50 0.30VCC 0.30VCC 4.50 HIGH Level Output Voltage ICC Quiescent Supply Current 3.00 2.90 4.40 4.50 4.40 1.29 1.52 1.29 1.90 2.15 1.90 3.00 VIN=VIL or VIH IOH= -16mA 2.40 2.80 2.40 3.00 IOH= -24mA 2.30 3.68 2.30 4.50 IOH= -32mA 3.90 4.20 VIN=VIL or VIH IOL= 100µA V V 3.80 0 0.10 0.10 0 0.10 0.10 0 0.10 0.10 0 0.10 0.10 V 1.65 IOL= 4mA 0.08 0.24 0.24 2.30 IOL= 8mA 0.30 0.30 3.00 VIN=VIL or VIH IOL= 16mA 0.10 0.15 0.40 0.40 3.00 IOL= 24mA 0.22 0.55 0.55 4.5 IOL= 32mA 0.22 0.55 0.55 ±0.1 ±1 µA 1 10 µA 10 µA 0 to 5.50 0 VIN=5.5V, GND VIN or VOUT=5.5V 1.65 to 5.50 VIN=5.5V, GND © 2000 Fairchild Semiconductor Corporation NC7SZ157 • Rev. 1.0.3 2.90 IOH= -4mA 4.50 Power Off Leakage Current 1.55 2.20 IOH= -8mA 3.00 Input Leakage Current 1.65 2.30 2.30 2.30 LOW Level Output Voltage 1.55 2.20 1.65 1.65 IOFF V 0.25VCC VIN=VIL or VIH IOH= -100µA Units Max. 1.65 to 1.95 3.00 IIN Min. 0.75VCC 2.30 VOL Max. 1.65 to 1.95 1.65 VOH Typ. TA=-40 to +85°C V NC7SZ157 — TinyLogic® UHS 2-Input Non-Inverting Multiplexer DC Electrical Characteristics www.fairchildsemi.com 4 Symbol Parameter Propagation Delay S to Z tPLH, tPHL Propagation Delay In to Z VCC TA=+25°C Conditions TA=-40 to +85°C Min. Typ. Max. Min. Max. 1.80 ± 0.15 2.5 6.0 11.5 2.5 12.0 2.50 ± 0.20 CL=15pF, 3.30 ± 0.30 RL=1MΩ, 1.2 3.5 6.1 1.2 6.5 0.8 2.6 4.1 0.8 4.5 5.00 ± 0.50 0.5 1.9 3.2 0.5 3.5 1.80 ± 0.15 2.5 5.9 10.0 2.5 10.5 5.00 ± 0.50 CL=15pF, 3.30 ± 0.30 RL=1MΩ, 1.2 3.5 5.8 1.2 6.1 0.8 2.6 3.9 0.8 4.2 5.00 ± 0.50 0.5 1.9 3.1 0.5 3.3 Propagation Delay S to Z 3.30 ± 0.30 CL=50pF, 5.00 ± 0.50 RL=500Ω, 1.2 3.2 4.8 1.2 5.2 0.8 2.4 3.8 0.8 4.1 Propagation Delay In to Z 3.30 ± 0.30 CL=50pF, 5.00 ± 0.50 RL=500Ω, 1.2 3.2 4.6 1.2 5.0 0.8 2.4 3.7 0.8 4.0 CIN Input Capacitance 0.00 CPD Power Dissipation Capacitance(4) 3.30 14 5.00 17 Units 2 Figure ns Figure 5 Figure 6 pF pF Figure 7 Note: 4. CPD is defined as the value of the internal equivalent capacitance which is derived from dynamic operating current consumption (ICCD) at no output loading and operating at 50% duty cycle. CPD is related to ICCD dynamic operating current by the expression: ICCD=(CPD)(VCC)(fIN)+(ICCstatic). NC7SZ157 — TinyLogic® UHS 2-Input Non-Inverting Multiplexer AC Electrical Characteristics Note: 5. CL includes load and stray capacitance. Input PRR=1.0MHz, tw=500ns. Figure 5. AC Test Circuit Figure 6. AC Waveforms Note: 6. Input=AC Waveform; PRR=Variable; Duty Cycle=50%. Figure 7. ICCD Test Circuit © 2000 Fairchild Semiconductor Corporation NC7SZ157 • Rev. 1.0.3 www.fairchildsemi.com 5 NC7SZ157 — TinyLogic® UHS 2-Input Non-Inverting Multiplexer Physical Dimensions SYMM C L 2.00±0.20 0.65 A 0.50 MIN 6 4 B PIN ONE 1.25±0.10 1 1.90 3 0.30 0.15 0.10 (0.25) 0.65 0.40 MIN A B 1.30 LAND PATTERN RECOMMENDATION 1.30 1.00 0.80 SEE DETAIL A 1.10 0.80 0.10 C 0.10 0.00 C 2.10±0.30 SEATING PLANE NOTES: UNLESS OTHERWISE SPECIFIED GAGE PLANE (R0.10) 0.25 0.10 0.20 A) THIS PACKAGE CONFORMS TO EIAJ SC-88, 1996. B) ALL DIMENSIONS ARE IN MILLIMETERS. C) DIMENSIONS DO NOT INCLUDE BURRS OR MOLD FLASH. D) DRAWING FILENAME: MKT-MAA06AREV6 30° 0° 0.46 0.26 DETAIL A SCALE: 60X Figure 8. 6-Lead, SC70, EIAJ SC-88, 1.25mm Wide Package drawings are provided as a service to customers considering Fairchild components. Drawings may change in any manner without notice. Please note the revision and/or date on the drawing and contact a Fairchild Semiconductor representative to verify or obtain the most recent revision. Package specifications do not expand the terms of Fairchild’s worldwide terms and conditions, specifically the warranty therein, which covers Fairchild products. Always visit Fairchild Semiconductor’s online packaging area for the most recent package drawings: http://www.fairchildsemi.com/packaging/. Tape and Reel Specifications Please visit Fairchild Semiconductor’s online packaging area for the most recent tape and reel specifications: http://www.fairchildsemi.com/products/analog/pdf/sc70-6_tr.pdf. Package Designator P6X © 2000 Fairchild Semiconductor Corporation NC7SZ157 • Rev. 1.0.3 Tape Section Cavity Number Cavity Status Cover Type Status Leader (Start End) 125 (Typical) Empty Sealed Carrier 3000 Filled Sealed Trailer (Hub End) 75 (Typical) Empty Sealed www.fairchildsemi.com 6 NC7SZ157 — TinyLogic® UHS 2-Input Non-Inverting Multiplexer Physical Dimensions 2X 0.05 C 1.45 B 2X (1) 0.05 C (0.49) 5X 1.00 (0.75) (0.52) 1X A TOP VIEW 0.55MAX (0.30) 6X PIN 1 0.05 C 0.05 0.00 RECOMMENED LAND PATTERN 0.05 C C 1.0 DETAIL A 0.10 0.05 0.45 0.35 0.10 0.00 6X 0.25 0.15 6X C B A C 0.40 0.30 0.35 5X 0.25 0.40 5X 0.30 0.5 (0.05) 6X BOTTOM VIEW DETAIL A PIN 1 TERMINAL 0.075 X 45 CHAMFER (0.13) 4X Notes: 1. CONFORMS TO JEDEC STANDARD M0-252 VARIATION UAAD 2. DIMENSIONS ARE IN MILLIMETERS 3. DRAWING CONFORMS TO ASME Y14.5M-1994 MAC06AREVC Figure 9. 6-Lead, MicroPak™, 1.0mm Wide Package drawings are provided as a service to customers considering Fairchild components. Drawings may change in any manner without notice. Please note the revision and/or date on the drawing and contact a Fairchild Semiconductor representative to verify or obtain the most recent revision. Package specifications do not expand the terms of Fairchild’s worldwide terms and conditions, specifically the warranty therein, which covers Fairchild products. Always visit Fairchild Semiconductor’s online packaging area for the most recent package drawings: http://www.fairchildsemi.com/packaging/. Tape and Reel Specifications Please visit Fairchild Semiconductor’s online packaging area for the most recent tape and reel specifications: http://www.fairchildsemi.com/products/logic/pdf/micropak_tr.pdf. Package Designator L6X © 2000 Fairchild Semiconductor Corporation NC7SZ157 • Rev. 1.0.3 Tape Section Cavity Number Cavity Status Cover Type Status Leader (Start End) 125 (Typical) Empty Sealed Carrier 5000 Filled Sealed Trailer (Hub End) 75 (Typical) Empty Sealed www.fairchildsemi.com 7 NC7SZ157 — TinyLogic® UHS 2-Input Non-Inverting Multiplexer Physical Dimensions DETAIL A 5X Figure 10. 6-Lead, MicroPak2, 1x1mm Body, .35mm Pitch Package drawings are provided as a service to customers considering Fairchild components. Drawings may change in any manner without notice. Please note the revision and/or date on the drawing and contact a Fairchild Semiconductor representative to verify or obtain the most recent revision. Package specifications do not expand the terms of Fairchild’s worldwide terms and conditions, specifically the warranty therein, which covers Fairchild products. Always visit Fairchild Semiconductor’s online packaging area for the most recent package drawings: http://www.fairchildsemi.com/packaging/. Tape and Reel Specifications Please visit Fairchild Semiconductor’s online packaging area for the most recent tape and reel specifications: http://www.fairchildsemi.com/packaging/MicroPAK2_6L_tr.pdf. Package Designator FHX © 2000 Fairchild Semiconductor Corporation NC7SZ157 • Rev. 1.0.3 Tape Section Cavity Number Cavity Status Cover Type Status Leader (Start End) 125 (Typical) Empty Sealed Carrier 5000 Filled Sealed Trailer (Hub End) 75 (Typical) Empty Sealed www.fairchildsemi.com 8 NC7SZ157 — TinyLogic® UHS 2-Input Non-Inverting Multiplexer © 2000 Fairchild Semiconductor Corporation NC7SZ157 • Rev. 1.0.3 www.fairchildsemi.com 9