OTS-4ATR Optiva Standard, 4 Duplex Analog Audio ™ Audio Transmission The OTS-4ATR provides for the transmission of 4 Channels of Duplex Analog Audio. ST, LC, SC or FC ST, LC, SC or FC Audio In/Out Audio Out/In Audio In/Out Audio Out/In System Design Video Audio Data All units come in an insert card version. The cards can be inserted into our 16-slot, 19” rack-mountable card cage (OT-CC-16-100) or one of our smaller Optiva™ Desktop Card Racks (OT-DTCR Series). The Optiva™ Desktop Card Racks can handle one, two or four insert cards, creating compact, mountable, stand alone systems. The use of separate OT-DTCR enclosures allows for future flexibility and expansion as all cards are hot-swappable and can be used in any enclosure. Each one of our card housing units operate with an appropriate power supply. See “Accessories” for power supply specifications. Optiva™ OTS-4ATR Each insert card comes with a label identifying the specific protocols handled, connector pin-out and other vital information. For optimal bandwidth allocation, each insert card can daisy-chain with an additional card in the same chassis. See “Optiva™ Upgrade Path”. OTS-4ART Features • Analog Audio over one fiber • TDM - Single fiber, dual wavelength Upgrade Path This system can be purchased without an optical port as an add-on to an existing Optiva™ system daisy-chain. (See “Non-Optical Version” below). Optiva™ bandwidth requirement The of this system is 20 Mbps. • Compatible with MDM-7000 Series for WDM and CWDM multiplexing • No EMI or RFI and no ground loops • Stand alone or rack-mount • Ideal for Professional AV applications Versions Available* Wavelength (nm) & Fiber Transmit/Receive** Receive/Transmit** 1310/1550 Multimode 1310/1550 Singlemode 1310/1550 SM (D) 1310/1550 SM (H) 1270-1610 SM (CWDM) OTS-4ATR-A2/A3M-XX-IC OTS-4ATR-A2/A3-XX-IC OTS-4ATR-A2/A3D-XX-IC OTS-4ATR-A2/A3H-XX-IC OTS-4ATR-L4/L4-XX-IC OTS-4ART-A3M/A2-XX-IC OTS-4ART-A3/A2-XX-IC OTS-4ART-A3D/A2-XX-IC OTS-4ART-A3H/A2-XX-IC OTS-4ART-L4/L4-XX-IC Non-Optical Version OTS-4ATR-NOC-IC OTS-4ART-NOC-IC Optical Connector Optical Budget (dB) Range*** (km) Form Factor ST, FC, LC or SC ST, FC, LC or SC ST, FC, LC or SC ST, FC, LC or SC ST, FC, LC or SC 10 12 17 25 Varies 3 20 40 60 20-70 IC (2-slot) IC (2-slot) IC (2-slot) IC (2-slot) IC (2-slot) N/A N/A N/A IC (2-slot) Analog Audio Codes - To indicate your Analog Audio impedance preference, please use the following instead of "A" in the model number: "AB" = Input Balanced 600 Ohm, Output Balanced 600 Ohm; "ABH" = Input Balanced Hi-Z, Output Balanced Low-Z; and "AUH" = Input Unbalanced Hi-Z, Output Unbalanced Low-Z. * Contact Opticomm for other versions available. ** XX indicates the type of optical connector. Each of ST, FC, LC or SC are available. *** Chromatic dispersion and additional losses should be taken into account. 800-867-8426 • [email protected] • www.opticomm.com • Contact Opticomm for custom requirements. Opticomm reserves the right to change specifications without notice Audio/FSK/Intercom Analog Audio Level Bandwidth Signal to Noise Ratio Total Harmonic Distortion Signal Coding Connector General Dimensions & Weight Operating temperature Storage temperature Humidity Operating voltage Consumption System Latency Local Monitoring Remote Monitoring 6 dBm In/Out 20 Hz to 20 KHz > 80 dB < 0.1% 24-bit Micro DB25 Impedance Options: Input Balanced 600 Ohm Balanced Hi-Z Unbalanced Hi-Z Insert Card (IC): 6.3” L x 0.8” W x 4.0” H -20° C to +55° C -40° C to +85° C 0 to 95% non-condensing 9-12 VDC 1 Amp Max per Insert Card Less than 10ms LED Status Indication Compatible with OptivaView™ SNMP Management Suite Output Balanced 600 Ohm Balanced Low-Z Unbalanced Low-Z Optiva™ Configurable Communication Platform Network Management SDI & HD-SDI Composite Video, Audio & Data 11 oz RGB/VGA/DVI Audio/FSK/Intercom Data (Ethernet/Serial/USB) CATV/RF & L-Band Optical Switching, Routing & Redundancy Passive Multiplexing Solutions Enclosures, Racks & Frames Power Supplies & Accessories MADE IN THE USA Sample Configuration