DBD250 Ordering number : ENA1204 SANYO Semiconductors DATA SHEET DBD250 Diffused Junction Silicon Diode 25.0A Single-Phase Bridge Rectifier Features • • • • Plastic molded structure. Glass passivation for high reliability. Peak reverse voltage : VRM=200V, 600V. Average output current : IO=25.0A. Specifications Absolute Maximum Ratings at Tc=25°C Parameter Peak Reverse Voltage Symbol Conditions DBD250C VRM Average Output Current IO Surge Forward Current Junction Temperature IFSM Tj Storage Temperature Tstg Dilective Strength Voltage VIS DBD250G 200 Unit 600 V Ta=40°C 6.0 Ta=40°C, With 300✕300✕3.0mm3 Cu fin 25.0 A 50Hz sine wave, 1cycle 400 A 150 °C Terminals tc case, AC 1 minute A --40 to +150 °C 2 kV Electrical Characteristics at Tc=25°C *Per Constituent element of bridge. Parameter Forward Voltage Symbol VF IR Reverse Current Thremal Resistance Rth(j-c) Conditions Ratings min typ IF=12.5A* VR=At each VRM* Junction-Case max Unit 1.05 V 10 μA 1.5 °C / W Note) Maximum tightening torque : 0.98Nm Any and all SANYO Semiconductor Co.,Ltd. products described or contained herein are, with regard to "standard application", intended for the use as general electronics equipment (home appliances, AV equipment, communication device, office equipment, industrial equipment etc.). The products mentioned herein shall not be intended for use for any "special application" (medical equipment whose purpose is to sustain life, aerospace instrument, nuclear control device, burning appliances, transportation machine, traffic signal system, safety equipment etc.) that shall require extremely high level of reliability and can directly threaten human lives in case of failure or malfunction of the product or may cause harm to human bodies, nor shall they grant any guarantee thereof. If you should intend to use our products for applications outside the standard applications of our customer who is considering such use and/or outside the scope of our intended standard applications, please consult with us prior to the intended use. If there is no consultation or inquiry before the intended use, our customer shall be solely responsible for the use. Specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein stipulate the performance, characteristics, and functions of the described products in the independent state, and are not guarantees of the performance, characteristics, and functions of the described products as mounted in the customer' s products or equipment. To verify symptoms and states that cannot be evaluated in an independent device, the customer should always evaluate and test devices mounted in the customer' s products or equipment. TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110-8534 JAPAN 73008RB TI IM TA-0858 No. A1204-1/3 DBD250 Package Dimensions unit : mm (typ) 7812-001 7.95 32.0 MAX 2.5 MIN 1.5 7.5 6.35 3.4 7.2 18.0 1.65 4.9 2.4 0.8 32.0 MAX 9 10.0 14.4 11.0 23.0 MAX IF -- VF 5 IFSM -- n 400 Ta=25°C Surge Foward Current, IFSM -- A 10 25°C 50° C 2 Ta= 1 Forward Current, IF -- A 3 7 5 3 2 1.0 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 Forward Voltage, VF -- V 1.3 1.4 IT13662 350 300 50 250 Hz 200 150 100 1.0 2 3 5 7 10 2 Number of Cycles, n 3 5 7 100 IT13663 IO -- Ta 32 With 300✕300✕3mm3 Cu fin Average Output Current, IO -- A 28 With heatsink 24 Re sis 20 tiv Ca e, in d ive ucti loa ve d loa pa 16 cit d 12 8 Without heatsink Resisti ve, ind uctive load Capacitiv e load 4 0 0 20 40 60 80 100 120 Ambient Temperature, Ta -- °C 140 160 IT13664 No. A1204-2/3 DBD250 SANYO Semiconductor Co.,Ltd. assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein. SANYO Semiconductor Co.,Ltd. strives to supply high-quality high-reliability products, however, any and all semiconductor products fail or malfunction with some probability. It is possible that these probabilistic failures or malfunction could give rise to accidents or events that could endanger human lives, trouble that could give rise to smoke or fire, or accidents that could cause damage to other property. When designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective circuits and error prevention circuits for safe design, redundant design, and structural design. In the event that any or all SANYO Semiconductor Co.,Ltd. products described or contained herein are controlled under any of applicable local export control laws and regulations, such products may require the export license from the authorities concerned in accordance with the above law. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise, without the prior written consent of SANYO Semiconductor Co.,Ltd. Any and all information described or contained herein are subject to change without notice due to product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the SANYO Semiconductor Co.,Ltd. product that you intend to use. Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed for volume production. Upon using the technical information or products described herein, neither warranty nor license shall be granted with regard to intellectual property rights or any other rights of SANYO Semiconductor Co.,Ltd. or any third party. SANYO Semiconductor Co.,Ltd. shall not be liable for any claim or suits with regard to a third party’s intellectual property rights which has resulted from the use of the technical information and products mentioned above. This catalog provides information as of July, 2008. Specifications and information herein are subject to change without notice. PS No. A1204-3/3