Ordering number : ENA1872
LC87F7DJ2C
CMOS IC
FROM 192K byte, RAM 8K byte on-chip
8-bit 1-chip Microcontroller
Overview
The SANYO LC87F7DJ2C is an 8-bit microcomputer that, centered around a CPU running at a minimum bus cycle time
of 50ns, integrates on a single chip a number of hardware features such as 1928K-byte flash ROM (onboard
programmable), 8K-byte RAM, an on-chip debugger, a LCD controller/driver, sophisticated 16-bit timer/counter (may
be divided into 8-bit timers), a 16-bit timer/counter (may be divided into 8-bit timers/counters or 8-bit PWMs), four 8-bit
timers with a prescaler, a 16-bit timer with a prescaler (may be divided into 8-bit timers), a base timer serving as a timeof-day clock, a day and time counter, a synchronous SIO interface (with automatic block transmission/reception
capabilities), an asynchronous/synchronous SIO interface, two UART ports (full duplex), an 12-bit 15-channel AD
converter, two 12-bit PWM channels, a high-speed clock counter, a system clock frequency divider, a small signal
detector, two remote control receive functions, and a 31-source 10-vector interrupt feature.
Features
Flash ROM
• Capable of on-board-programming with wide range, 3.0 to 3.6V, of voltage source.
• Block-erasable in 2-byte units
• 196608 × 8 bits
RAM
• 8192 × 9 bits
Minimum Bus Cycle Time
• 50.0ns (20MHz)
VDD=2.7 to 3.6V
Note: The bus cycle time here refers to the ROM read speed.
* This product is licensed from Silicon Storage Technology, Inc. (USA), and manufactured and sold by
SANYO Semiconductor Co., Ltd.
Any and all SANYO Semiconductor Co.,Ltd. products described or contained herein are, with regard to
"standard application", intended for the use as general electronics equipment (home appliances, AV equipment,
communication device, office equipment, industrial equipment etc.). The products mentioned herein shall not be
intended for use for any "special application" (medical equipment whose purpose is to sustain life, aerospace
instrument, nuclear control device, burning appliances, transportation machine, traffic signal system, safety
equipment etc.) that shall require extremely high level of reliability and can directly threaten human lives in case
of failure or malfunction of the product or may cause harm to human bodies, nor shall they grant any guarantee
thereof. If you should intend to use our products for applications outside the standard applications of our
customer who is considering such use and/or outside the scope of our intended standard applications, please
consult with us prior to the intended use. If there is no consultation or inquiry before the intended use, our
customer shall be solely responsible for the use.
Specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein stipulate
the performance, characteristics, and functions of the described products in the independent state, and are not
guarantees of the performance, characteristics, and functions of the described products as mounted in the
customer' s products or equipment. To verify symptoms and states that cannot be evaluated in an independent
device, the customer should always evaluate and test devices mounted in the customer' s products or
equipment.
Ver.1.0
N1710HKIM 20101105-S00001 No.A1872-1/26
LC87F7DJ2C
Minimum Instruction Cycle Time (tCYC)
• 150ns (20MHz)
VDD=2.7 to 3.6V
Ports
• Normal withstand voltage I/O ports
Ports whose I/O direction can be designated in 1 bit units 29 (P0n, P1n, P70 to P73, P8n, XT2)
• Normal withstand voltage input port
1 (XT1)
• LCD ports
Segment output
54 (S00 to S53)
Common output
4 (COM0 to COM3)
Bias terminals for LCD driver
3 (V1 to V3)
Other functions
Input/output ports
54 (P3n, PAn, PBn, PCn, PDn, PEn, PFn,)
Input ports
7 (PLn)
• Dedicated oscillator ports
2 (CF1, CF2)
• Reset pin
1 (RES)
• Power pins
6 (VSS1 to VSS3, VDD1 to VDD3)
LCD Controller
1) Seven display modes are available (static, 1/2, 1/3, 1/4 duty × 1/2, 1/3 bias)
2) Segment output and common output can be switched to general-purpose input/output ports
Small Signal Detection (MIC signals etc)
1) Counts pulses with the level which is greater than a preset value
2) 2-bit counter
Timers
• Timer 0: 16-bit timer/counter with two capture registers.
Mode 0: 8-bit timer with an 8-bit programmable prescaler (with two 8-bit capture registers) × 2 channels
Mode 1: 8-bit timer with an 8-bit programmable prescaler (with two 8-bit capture registers)
+ 8-bit counter (with two 8-bit capture registers)
Mode 2: 16-bit timer with an 8-bit programmable prescaler (with two 16-bit capture registers)
Mode 3: 16-bit counter (with two 16-bit capture registers)
• Timer 1: 16-bit timer/counter that supports PWM/toggle outputs
Mode 0: 8-bit timer with an 8-bit prescaler (with toggle outputs)
+ 8-bit timer/counter with an 8-bit prescaler (with toggle outputs)
Mode 1: 8-bit PWM with an 8-bit prescaler × 2 channels
Mode 2: 16-bit timer/counter with an 8-bit prescaler (with toggle outputs)
(toggle outputs also possible from the lower-order 8 bits)
Mode 3: 16-bit timer with an 8-bit prescaler (with toggle outputs)
(The lower-order 8 bits can be used as PWM.)
• Timer 4: 8-bit timer with a 6-bit prescaler
• Timer 5: 8-bit timer with a 6-bit prescaler
• Timer 6: 8-bit timer with a 6-bit prescaler (with toggle output)
• Timer 7: 8-bit timer with a 6-bit prescaler (with toggle output)
• Timer 8: 16-bit timer
Mode 0: 8-bit timer with an 8-bit prescaler × 2 channels
Mode 1: 16-bit timer with an 8-bit prescaler
• Base timer
1) The clock is selectable from the subclock (32.768kHz crystal oscillation), system clock,
and timer 0 prescaler output.
2) Interrupts programmable in 5 different time schemes
• Day and time counter
1) Using with a base timer, it can be used as 65000 day + minute + second counter.
No.A1872-2/26
LC87F7DJ2C
High-speed Clock Counter
1) Can count clocks with a maximum clock rate of 20MHz (at a main clock of 10MHz).
2) Can generate output real-time.
SIO
• SIO0: 8-bit synchronous serial interface
1) LSB first/MSB first mode selectable
2) Built-in 8-bit baudrate generator (maximum transfer clock cycle = 4/3 tCYC)
3) Automatic continuous data transmission (1 to 256 bits specifiable in 1-bit units, suspension and resumption of
data transmission possible in 1-byte units)
• SIO1: 8-bit asynchronous/synchronous serial interface
Mode 0: Synchronous 8-bit serial I/O (2- or 3-wire configuration, 2 to 512 tCYC transfer clocks)
Mode 1: Asynchronous serial I/O (half-duplex, 8-data bits, 1-stop bit, 8 to 2048 tCYC baudrates)
Mode 2: Bus mode 1 (start bit, 8-data bits, 2 to 512 tCYC transfer clocks)
Mode 3: Bus mode 2 (start detect, 8-data bits, stop detect)
UART1
• Full duplex
• 7/8/9 bit data bits selectable
• 1 stop bit (2-bit in continuous data transmission)
• Built-in baudrate generator
UART2
• Full duplex
• 7/8/9 bit data bits selectable
• 1 stop bit (2-bit in continuous data transmission)
• Built-in baudrate generator
AD Converter: 12 bits × 15 channels
PWM: Multi frequency 12-bit PWM × 2 channels
Remote Control Receiver Circuit1
1) Noise rejection function
(Units of noise rejection filter: about 120μs, when selecting a 32.768kHz crystal oscillator as a clock.)
2) Supporting reception formats with a guide-pulse of half-clock/clock/none.
3) Determines a end of reception by detecting a no-signal periods (No carrier).
(Supports same reception format with a different bit length.)
4) X’tal HOLD mode release function
Remote Control Receiver Circuit2
1) Noise rejection function
(Units of noise rejection filter: about 120μs, when selecting a 32.768kHz crystal oscillator as a clock.)
2) Supporting reception formats with a guide-pulse of half-clock/clock/none.
3) Determines a end of reception by detecting a no-signal periods (No carrier).
(Supports same reception format with a different bit length.)
4) X’tal HOLD mode release function
Watchdog Timer
• External RC watchdog timer
• Interrupt and reset signals selectable
Clock Output Function
1) Able to output selected oscillation clock 1/1, 1/2, 1/4, 1/8, 1/16, 1/32, 1/64 as system clock.
2) Able to output oscillation clock of sub clock.
No.A1872-3/26
LC87F7DJ2C
Interrupts
• 31 sources, 10 vector addresses
1) Provides three levels (low (L), high (H), and highest (X)) of multiplex interrupt control. Any interrupt requests of
the level equal to or lower than the current interrupt are not accepted.
2) When interrupt requests to two or more vector addresses occur at the same time, the interrupt of the highest level
takes precedence over the other interrupts. For interrupts of the same level, the interrupt into the smallest vector
address takes precedence.
No.
Vector Address
Level
Interrupt Source
1
00003H
X or L
INT0
2
0000BH
X or L
INT1
3
00013H
H or L
INT2/T0L/INT4/remote control receiver1
4
0001BH
H or L
INT3/base timer/INT5/remote control receiver2
5
00023H
H or L
T0H/INT6
6
0002BH
H or L
T1L/T1H/INT7
7
00033H
H or L
SIO0/UART1 receive/UART2 receive/T8L/T8H
8
0003BH
H or L
SIO1/UART1 transmit/UART2 transmit
9
00043H
H or L
ADC/MIC/T6/T7/PWM4/PWM5
10
0004BH
H or L
Port 0/T4/T5
• Priority levels X > H > L
• Of interrupts of the same level, the one with the smallest vector address takes precedence.
• IFLG (List of interrupt source flag function)
1) Shows a list of interrupt source flags that caused a branching to a particular vector address
(shown in the diagram above).
Subroutine Stack Levels: 4096 levels (The stack is allocated in RAM.)
High-speed Multiplication/Division Instructions
• 16 bits × 8 bits
(5 tCYC execution time)
• 24 bits × 16 bits
(12 tCYC execution time)
• 16 bits ÷ 8 bits
(8 tCYC execution time)
• 24 bits ÷ 16 bits
(12 tCYC execution time)
Oscillation Circuits
• RC oscillation circuit (internal):
For system clock
• CF oscillation circuit:
For system clock, with internal Rf and external Rd
• Crystal oscillation circuit:
For low-speed system clock, with internal Rf and external Rd
• Frequency variable RC oscillation circuit (internal): For system clock
1) Adjustable in ±4% (typ.) step from a selected center frequency.
2) Measures the frequency of the source oscillation clock using the input signal from XT1 as the reference.
System Clock Divider Function
• Can run on low current.
• The minimum instruction cycle selectable from 300ns, 600ns, 1.2μs, 2.4μs, 4.8μs, 9.6μs, 19.2μs, 38.4μs,
and 76.8μs (at a main clock rate of 10MHz).
Standby Function
• HALT mode: Halts instruction execution while allowing the peripheral circuits to continue operation.
(Some parts of the serial transfer function stops operation.)
1) Oscillation is not halted automatically.
2) Canceled by a system reset or occurrence of an interrupt
Continued on next page.
No.A1872-4/26
LC87F7DJ2C
Continued from preceding page.
• HOLD mode: Suspends instruction execution and the operation of the peripheral circuits.
1) The CF, RC, X’tal, and frequency variable RC oscillators automatically stop operation.
2) There are three ways of resetting the HOLD mode.
(1) Setting the reset pin to the low level
(2) Setting at least one of the INT0, INT1, INT2, INT4, and INT5 pins to the specified level
(3) Having an interrupt source established at port 0
• X'tal HOLD mode: Suspends instruction execution and the operation of the peripheral circuits except the base timer
and the remote control receiver circuit.
1) The CF, RC, and frequency variable RC oscillators automatically stop operation.
2) The state of crystal oscillation established when the X'tal HOLD mode is entered is retained.
3) There are five ways of resetting the X'tal HOLD mode.
(1) Setting the reset pin to the low level
(2) Setting at least one of the INT0, INT1, INT2, INT4, and INT5 pins to the specified level
(3) Having an interrupt source established at port 0
(4) Having an interrupt source established in the base timer circuit
(5) Having an interrupt source established in the remote control receiver circuit
On-chip Debugger
• Supports software debugging with the IC mounted on the target board.
Package Form
• QIP100E(14×20): Lead-free type/Halogen-free type
• TQFP100(14×14): Lead-free type/Halogen-free type (Under development)
Development Tools
• On-chip debugger: TCB87 TypeB +LC87F7DJ2C or TCB87 TypeC(3Lines Cable)+LC87F7DJ2C
Flash ROM Programming Boards
Package
Programming boards
QIP100E(14×20)
W87FQ100
TQFP100(14×14)
W87FSQ100
Flash ROM Programmer
Maker
Model
Supported version
Device
(Note 2)
LC87F7DJ2C
AF9708
Single
AF9709/AF9709B/AF9709C
(Including product of Ando
Electric Co., Ltd)
Flash Support Group, Inc.
AF9723/AF9723B(Main body)
(FSG)
(Including product of Ando
Gang
(Note 2)
Electric Co., Ltd)
LC87F7DJ2C
AF9833(Unit)
(Including product of Ando
(Note 2)
Electric Co., Ltd)
Flash Support Group, Inc.
AF9101/AF9103(Main body)
(FSG)
Onboard
(FSG)
+
Single/Gang
SIB87(interface driver)
SANYO (Note 1)
LC87F7DJ2C
(SANYO)
Single/Gang
SANYO
(Note 2)
SKK/SKK Type B
Application Version
(SANYO FWS)
After 1.05
Onboard
SKK-DBG Type B
Chip Data Version
Single/Gang
(SANYO FWS)
After 2.23
LC87F7DJ2C
Note 1: With the FSG onboard programmer (AF9101/AF9103) and the serial interface driver provided by SANYO,
PC-less standalone onboard programming is possible
Note 2: Depending on programming conditions, it is necessary to use a dedicated programming device and a program.
Please contact SANYO or FSG if you have any questions or difficulties regarding this matter.
No.A1872-5/26
LC87F7DJ2C
Package Dimensions
unit : mm (typ)
3151A
23.2
0.8
20.0
51
50
100
31
14.0
81
1
17.2
80
30
0.65
0.15
0.3
0.1
3.0max
(2.7)
(0.58)
SANYO : QIP100E(14X20)
Package Dimensions
unit : mm (typ)
3274
[Under Development]
75
0.5
16.0
14.0
51
50
100
26
14.0
16.0
76
1
0.5
0.2
25
0.125
1.2max
0.1
(1.0)
(1.0)
SANYO : TQFP100(14X14)
No.A1872-6/26
LC87F7DJ2C
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
V3/PL6/AN14/DBGP2
S47/PF7/INT7
S46/PF6/INT6
S45/PF5
S44/PF4
S43/PF3
S42/PF2
S41/PF1
S40/PF0
S39/PE7
S38/PE6
S37/PE5
S36/PE4
S35/PE3
S34/PE2
S33/PE1
S32/PE0
S31/PD7
S30/PD6
S29/PD5
S28/PD4
S27/PD3
S26/PD2
S25/PD1
S24/PD0
VSS2
VDD2
S23/PC7
S22/PC6
S21/PC5
Pin Assignments
LC87F7DJ2C
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
S20/PC4
S19/PC3
S18/PC2
S17/PC1
S16/PC0
S15/PB7
S14/PB6
S13/PB5
S12/PB4
S11/PB3
S10/PB2
S9/PB1
S8/PB0
S7/PA7
S6/PA6
S5/PA5
S4/PA4
S3/PA3
S2/PA2
S1/PA1
P06/T6O
P07/T7O
P10/SO0
P11/SI0/SB0
P12/SCK0
P13/SO1
P14/SI1/SB1
P15/SCK1
P16/T1PWML
P17/T1PWMH/BUZ
RES
XT1/AN10
XT2/AN11
VSS1
CF1
CF2
VDD1
P80/AN0
P81/AN1
P82/AN2
P83/AN3
P84/AN4
P85/AN5
P86/AN6
P87/AN7/MICIN
P70/INT0/T0LCP/AN8
P71/INT1/T0HCP/AN9
P72/INT2/T0IN/NKIN
P73/INT3/T0IN/RMIN
S0/PA0
V2/PL5/AN13/DBGP1
V1/PL4/AN12/DBGP0
COM0/PL0
COM1/PL1
COM2/PL2
COM3/PL3
P30/INT4/T1IN/INT6/T0LCP1/PWM4/S48
P31/INT4/T1IN/PWM5/S49
VSS3
VDD3
P32/INT4/T1IN/UTX1/S50
P33/INT4/T1IN/URX1/S51
P34/INT5/T1IN/INT7/T0HCP1/UTX2/S52
P35/INT5/T1IN/URX2/S53
P00/DGBP0
P01/DGBP1
P02/DGBP2
P03/INT6
P04/INT7
P05/CKO
Top view
SANYO: QIP100E(14×20) “Lead-free Type/Halogen-free type”
No.A1872-7/26
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
S46/PF6
S45/PF5
S44/PF4
S43/PF3
S42/PF2
S41/PF1
S40/PF0
S39/PE7
S38/PE6
S37/PE5
S36/PE4
S35/PE3
S34/PE2
S33/PE1
S32/PE0
S31/PD7
S30/PD6
S29/PD5
S28/PD4
S27/PD3
S26/PD2
S25/PD1
S24/PD0
VSS2
VDD2
LC87F7DJ2C
LC87F7DJ2C
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
S23/PC7
S22/PC6
S21/PC5
S20/PC4
S19/PC3
S18/PC2
S17/PC1
S16/PC0
S15/PB7
S14/PB6
S13/PB5
S12/PB4
S11/PB3
S10/PB2
S9/PB1
S8/PB0
S7/PA7
S6/PA6
S5/PA5
S4/PA4
S3/PA3
S2/PA2
S1/PA1
S0/PA0
P73/INT3/T0IN/RMIN
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
P11/SI0/SB0
P12/SCK0
P13/SO1
P14/SI1/SB1
P15/SCK1
P16/T1PWML
P17/T1PWMH/BUZ
RES
XT1/AN10
XT2/AN11
VSS1
CF1
CF2
VDD1
P80/AN0
P81/AN1
P82/AN2
P83/AN3
P84/AN4
P85/AN5
P86/AN6
P87/AN7/MICIN
P70/INT0/T0LCP/AN8
P71/INT1/T0HCP/AN9
P72/INT2/T0IN/NKIN
S47/PF7
V3/PL6/AN14/DBGP2
V2/PL5/AN13/DBGP1
V1/PL4/AN12/DBGP0
COM0/PL0
COM1/PL1
COM2/PL2
COM3/PL3
P30/INT4/T1IN/INT6/T0LCP1/PWM4/S48
P31/INT4/T1IN/PWM5/S49
VSS3
VDD3
P32/INT4/T1IN/UTX1/S50
P33/INT4/T1IN/URX1/S51
P34/INT5/T1IN/INT7/T0HCP1/S52
P35/INT5/T1IN/S52
P00/DGBP0
P01/DGBP1
P02/T8LO/DGBP2
P03/T8HO
P04
P05/CKO
P06/T6O
P07/T7O
P10/SO0
Top view
SANYO: TQFP100(14×14) “Lead-free type/Halogen-free type” (Under development)
No.A1872-8/26
LC87F7DJ2C
System Block Diagram
Interrupt control
IR
PLA
Standby control
Flash ROM
RC
VMRC
Clock
generator
CF
PC
X’tal
ACC
B register
C register
ALU
SIO0
Bus interface
SIO1
Port 0
Timer 0
(High speed clock counter)
Port 1
Timer 1
Port 3
PSW
RAR
Base timer
Port 7
LCD Controller
Port 8
INT0 to 7
Noise Rejection Filter
ADC
Timer 4
Small signal
detector
Timer 5
Timer 6
UART1
UART2
PWM4/5
Timer 7
Remote control
receiver circuit 1
Timer 8
Remote control
receiver circuit 2
Day and time
counter
RAM
Stack pointer
Watchdog timer
On-chip debugger
No.A1872-9/26
LC87F7DJ2C
Pin Description
Pin Name
VSS1
VSS2
VSS3
VDD1
I/O
Description
Option
-
- power supply pin
No
-
+ power supply pin
No
• 8-bit I/O port
Yes
VDD2
VDD3
Port 0
I/O
• I/O specifiable in 1-bit units
P00 to P07
• Pull-up resistors can be turned on and off in 1-bit units.
• Input for HOLD release
• Input for port 0 interrupt
• Shared pins
P03: INT6 input
P04: INT7 input
P05: Clock output (system clock/can selected from sub clock)
P06: Timer 6 toggle output
P07: Timer 7 toggle output
On chip debugger pins: DBGP0 to DBGP2(P00 to P02)
Port 1
I/O
• 8-bit I/O port
Yes
• I/O specifiable in 1-bit units
P10 to P17
• Pull-up resistors can be turned on and off in 1-bit units.
• Shared pins
P10: SIO0 data output
P11: SIO0 data input/bus I/O
P12: SIO0 clock I/O
P13: SIO1 data output
P14: SIO1 data input/bus I/O
P15: SIO1 clock I/O
P16: Timer 1PWML output
P17: Timer 1PWMH output/beeper output
Port 3
P30 to P35
I/O
• 6-bit I/O port
Yes
• Segment output for LCD
• I/O specifiable in 1-bit units
• Pull-up resistors can be turned on and off in 1-bit units.
• Shared pins
P30 to P33: INT4 input/HOLD release input/timer 1 event input/timer 0L capture input/
timer 0H capture input
P34 to P35: INT5 input/HOLD release input/timer 1 event input/timer 0L capture input/
timer 0H capture input
P30: PWM4 output/INT6 input/timer 0L capture 1 input
P31: PWM5 output
P32: UART1 transmit
P33: UART1 receive
P34: UART2 transmit/INT7 input/timer 0H capture 1 input
P35: UART2 receive
Interrupt acknowledge type
Rising
Falling
INT4
enable
enable
INT5
enable
enable
INT6
enable
INT7
enable
Rising &
H level
L level
enable
disable
disable
enable
disable
disable
enable
enable
disable
disable
enable
enable
disable
disable
Falling
Continued on next page.
No.A1872-10/26
LC87F7DJ2C
Continued from preceding page.
Pin Name
Port 7
I/O
I/O
Description
Option
• 4-bit I/O port
No
• I/O specifiable in 1-bit units
P70 to P73
• Pull-up resistors can be turned on and off in 1-bit units.
• Shared pins
P70: INT0 input/HOLD release input/timer 0L capture input/watchdog timer output
P71: INT1 input/HOLD release input/timer 0H capture input
P72: INT2 input/HOLD release input/timer 0 event input/timer 0L capture input/
high speed clock counter input
P73: INT3 input (with noise filter)/timer 0 event input/timer 0H capture input/
remote control receiver input
AD converter input ports: AN8 (P70), AN9 (P71)
Interrupt acknowledge type
Port 8
I/O
Rising
Falling
INT0
enable
enable
INT1
enable
enable
INT2
enable
INT3
enable
Rising &
H level
L level
disable
enable
enable
disable
enable
enable
enable
enable
disable
disable
enable
enable
disable
disable
Falling
• 8-bit I/O port
No
• I/O specifiable in 1-bit units
P80 to P87
• Shared pins
AD converter input ports: AN0 to AN7
Small signal detector input port: MICIN (P87)
S0/PA0 to
I/O
I/O
I/O
I/O
I/O
No
• Segment output for LCD
No
• Segment output for LCD
No
• Can be used as general-purpose I/O port (PE)
S39/PE7
S40/PF0 to
• Segment output for LCD
• Can be used as general-purpose I/O port (PD)
S31/PD7
S32/PE0 to
No
• Can be used as general-purpose I/O port (PC)
S23/PC7
S24/PD0 to
• Segment output for LCD
• Can be used as general-purpose I/O port (PB)
S15/PB7
S16/PC0 to
No
• Can be used as general-purpose I/O port (PA)
S7/PA7
S8/PB0 to
• Segment output for LCD
I/O
• Segment output for LCD
No
• Can be used as general-purpose I/O port (PF)
S47/PF7
PF6: INT6 input
PF7: INT7 input
COM0/PL0 to
I/O
No
• Can be used as general-purpose input port (PL)
COM3/PL3
V1/PL4 to
• Common output for LCD
I/O
• LCD output bias power supply
No
• Can be used as general-purpose input port (PL)
V3/PL6
• Shared pins
AD converter input ports: AN12 (V1) to AN14 (V3)
On-chip debugger pins: DBGP0 (V1) to DBGP2 (V3)
RES
Input
Reset pin
No
XT1
Input
• 32.768kHz crystal oscillator input pin
No
• Shared pins
General-purpose input port
AD converter input port: AN10
XT2
I/O
Must be connected to VDD1 if not to be used.
• 32.768kHz crystal oscillator output pin
No
• Shared pins
General-purpose I/O port
AD converter input port: AN11
Must be set for oscillation and kept open if not to be used.
CF1
Input
CF2
Output
Ceramic resonator input pin
No
Ceramic resonator output pin
No
No.A1872-11/26
LC87F7DJ2C
Port Output Types
The table below lists the types of port outputs and the presence/absence of a pull-up resistor.
Data can be read into any input port even if it is in the output mode.
Port Name
Option Selected
in Units of
Option Type
P00 to P07
each bit
1
P10 to P17
each bit
P30 to P35
each bit
Output Type
Pull-up Resistor
CMOS
Programmable
2
Nch-open drain
Programmable
1
CMOS
Programmable
2
Nch-open drain
Programmable
1
CMOS
Programmable
2
Nch-open drain
Programmable
Programmable
P70
-
No
Nch-open drain
P71 to P73
-
No
CMOS
Programmable
P80 to P87
-
No
Nch-open drain
No
S0/PA0 to S47/PF7
-
No
CMOS
Programmable
COM0/PL0 to
-
No
Input only
No
COM3/PL3
V1/PL4 to V3/PL6
-
No
Input only
No
XT1
-
No
Input only
No
XT2
-
No
Output for 32.768kHz crystal oscillator
No
(Nch-open drain when in general-purpose
output mode)
User Option List
Option Name
Option Type
P00 to P07
Mask Version
*1
Flash Version
{
{
Option Selected in
Specified item
Units of
each bit
CMOS
Nch-open drain
Port output form
P10 to P17
{
{
each bit
CMOS
Nch-open drain
P30 to P35
{
{
each bit
CMOS
Nch-open drain
Program start
address
-
×
*2
{
-
00000H
1FF00H
*1: Mask option selection - No change possible after the mask is completed.
*2: Program start address of the mask version is 00000h.
LSI
VDD1
Power
supply
For backup *2
VDD2
VDD3
VSS1
VSS2 VSS3
*1 Connect the IC as shown below to minimize the noise input to the VDD1 pin.
Be sure to electrically short the VSS1, VSS2, and VSS3 pins.
*2 The internal memory is sustained by VDD1. If none of VDD2 and VDD3 are backed up, the high level output at the
ports are unstable in the HOLD backup mode, allowing through current to flow into the input buffer and thus
shortening the backup time.
Make sure that the port outputs are held at the low level in the HOLD backup mode.
No.A1872-12/26
LC87F7DJ2C
Absolute Maximum Ratings at Ta = 25°C, VSS1 = VSS2 = VSS3 = 0V
Parameter
Symbol
Pin/Remarks
Specification
Conditions
VDD[V]
Maximum supply
VDD max
VDD1, VDD2, VDD3
VDD1=VDD2=VDD3
V1/PL4, V2/PL5,
VDD1=VDD2=VDD3
voltage
supply voltage for
VLCD
LCD
V3/PL6
Input voltage
VI(1)
Port L
XT1, CF1, RES
VI(2)
Input/output
VIO(1)
voltage
VDD2, VDD3
min
typ
max
-0.3
+4.6
-0.3
VDD
-0.3
VDD+0.3
VSS
VDD+0.1
-0.3
VDD+0.3
unit
V
Ports 0, 1, 3, 7, 8
Ports A, B, C
Ports D, E, F
XT2
Peak output
IOPH(1)
Ports 0, 1, 32 to 35
current
• CMOS output selected
• Current at each pin
IOPH(2)
Ports 30, 31
• CMOS output selected
• Current at each pin
IOPH(3)
Ports 71 to 73
Current at each pin
IOPH(4)
Ports A, B, C
Current at each pin
Ports D, E, F
High level output current
Mean output
IOMH(1)
Ports 0, 1, 32 to 35
current
(Note 1-1)
• CMOS output selected
• Current at each pin
IOMH(2)
Ports 30, 31
• CMOS output selected
• Current at each pin
IOMH(3)
Ports 71 to 73
Current at each pin
IOMH(4)
Ports A, B, C
Current at each pin
Ports D, E, F
-20
-5
-5
-7.5
-15
-3
-3
Total output
ΣIOAH(1)
Ports 0, 1, 32 to 35
Total of all pins
-25
current
ΣIOAH(2)
Ports 30, 31
Total of all pins
-25
-45
ΣIOAH(3)
Ports 0, 1, 3
Total of all pins
ΣIOAH(4)
Ports 71 to 73
Total of all pins
-5
ΣIOAH(5)
Ports A, B, C
Total of all pins
-25
ΣIOAH(6)
Ports D, E, F
Total of all pins
-25
ΣIOAH(7)
Ports A, B, C
Total of all pins
Ports D, E, F
-45
mA
Peak output
IOPL(1)
Ports 0, 1, 32 to 35
Current at each pin
20
current
IOPL(2)
Ports 30, 31
Current at each pin
30
IOPL(3)
Ports 7, 8
Current at each pin
XT2
IOPL(4)
Ports A, B, C
Current at each pin
Ports D, E, F
Low level output current
-10
10
10
Mean output
IOML(1)
Ports 0, 1, 32 to 35
Current at each pin
15
current
IOML(2)
Ports 30, 31
Current at each pin
20
IOML(3)
Ports 7, 8
Current at each pin
(Note 1-1)
XT2
IOML(4)
Ports A, B, C
Current at each pin
Ports D, E, F
7.5
7.5
Total output
ΣIOAL(1)
Ports 0, 1, 32 to 35
Total of all pins
45
current
ΣIOAL(2)
Ports 30, 31
Total of all pins
45
ΣIOAL(3)
Ports 0, 1, 3
Total of all pins
80
ΣIOAL(4)
Ports 7, 8
Total of all pins
XT2
ΣIOAL(5)
Ports A, B, C
Total of all pins
45
ΣIOAL(6)
Ports D, E, F
Total of all pins
45
ΣIOAL(7)
Ports A, B, C
Total of all pins
Ports D, E, F
Maximum power
dissipation
20
Pd max
QIP100E(14×20)
Ta=-40 to +85°C
TQFP100(14×14)
Ta=-40 to +85°C
80
mW
Note 1-1: The mean output current is a mean value measured over 100ms.
Continued on next page.
No.A1872-13/26
LC87F7DJ2C
Continued from preceding page.
Parameter
Symbol
Pin/Remarks
Specification
Conditions
VDD[V]
Operating ambient
Topr
temperature
Storage ambient
min
typ
max
-40
+85
-55
+125
unit
°C
Tstg
temperature
Allowable Operating Range at Ta = -40°C to +85°C, VSS1 = VSS2 = VSS3 = 0V
Parameter
Symbol
Pin/Remarks
Specification
Conditions
VDD[V]
Operating
VDD(1)
VDD1=VDD2=VDD3
min
typ
max
unit
0.150μs ≤ tCYC ≤ 200μs
supply voltage
2.7
3.6
2.0
3.6
(Note 2-1)
Memory
VHD
VDD1
sustaining
RAM and register contents
sustained in HOLD mode.
supply voltage
High level input
VIH(1)
voltage
Ports 0, 3, 8
Output disabled
Ports A, B, C, D, E, F
2.7 to 3.6
Port L
VIH(2)
Port 1
• Output disabled
Ports 71 to 73
• When INT1VTSL=0 (P71 only)
P70 port input/
2.7 to 3.6
0.3VDD
+0.7
0.3VDD
+0.7
VDD
VDD
interrupt side
VIH(3)
P71 interrupt side
• Output disabled
• When INT1VTSL=1
VIH(4)
P87 small signal
Output disabled
input side
VIH(5)
P70 watchdog timer
VIH(6)
XT1,XT2,CF1, RES
VIL(1)
Ports 0, 3, 8
Output disabled
side
Low level input
voltage
2.7 to 3.6
0.85VDD
VDD
2.7 to 3.6
0.75VDD
VDD
2.7 to 3.6
0.9VDD
VDD
2.7 to 3.6
0.75VDD
VDD
2.7 to 3.6
VSS
0.2VDD
2.7 to 3.6
VSS
0.2VDD
2.7 to 3.6
VSS
0.45VDD
2.7 to 3.6
VSS
0.25VDD
2.7 to 3.6
VSS
2.7 to 3.6
VSS
0.25VDD
2.7 to 3.6
0.150
200
2.7 to 3.6
0.1
20
V
Output disabled
Ports A, B, C, D, E, F
Port L
VIL(2)
Port 1
• Output disabled
Ports 71 to 73
• When INT1VTSL=0 (P71 only)
P70 port input/
interrupt side
VIL(3)
P71 interrupt side
• Output disabled
• When INT1VTSL=1
VIL(4)
P87 small signal
Output disabled
input side
VIL(5)
P70 watchdog timer
Output disabled
side
VIL(6)
Instruction cycle
XT1,XT2,CF1,RES
0.8VDD
-1.0
tCYC
time
μs
(Note 2-2)
External system
clock frequency
FEXCF(1)
CF1
• CF2 pin open
• System clock frequency
division ratio=1/1
• External system clock
MHz
duty=50±5%
• CF2 pin open
• System clock frequency
2.7 to 3.6
0.2
40
division ratio=1/2
Note 2-1: VDD must be held greater than or equal to 3.0V in the flash ROM onboard programming mode.
Note 2-2: Relationship between tCYC and oscillation frequency is 3/FmCF at a division ratio of 1/1 and 6/FmCF at
a division ratio of 1/2.
Continued on next page.
No.A1872-14/26
LC87F7DJ2C
Continued from preceding page.
Parameter
Symbol
Pin/Remarks
Specification
Conditions
VDD[V]
Oscillation
FmCF(1)
CF1, CF2
frequency
• 20MHz ceramic oscillation
• See Fig. 1.
range
FmRC
Internal RC oscillation
(Note 2-3)
FmVMRC(1)
• Frequency variable RC
min
typ
2.7 to 3.6
2.7 to 3.6
max
unit
20
0.3
1.0
2.0
source oscillation
• When
VMRAJ2 to 0=4,
2.7 to 3.6
10
MHz
VMFAJ2 to 0=0,
VMSL4M=0
FmVMRC(2)
• Frequency variable RC
source oscillation
• When
VMRAJ2 to 0=4,
2.7 to 3.6
4
2.7 to 3.6
32.768
VMFAJ2 to 0=0,
VMSL4M=1
FsX’tal
XT1, XT2
• 32.768kHz crystal oscillation
• See Fig. 2.
Frequency
OpVMRC(1)
When VMSL4M=0
variable RC
OpVMRC(2)
When VMSL4M=1
oscillation
kHz
2.7 to 3.6
8
10
12
2.7 to 3.6
3.5
4
4.5
2.7 to 3.6
8
24
64
2.7 to 3.6
1
4
8
MHz
usable range
Frequency
VmADJ(1)
Each step of VMRAJn
variable RC
oscillation
(Wide range)
VmADJ(2)
%
Each step of VMFAJn
adjustment
(Small range)
range
Note 2-3: See Tables 1 and 2 for the oscillation constants.
Electrical Characteristics at Ta = -40°C to +85°C, VSS1 = VSS2 = VSS3 = 0V
Parameter
Symbol
Pin/Remarks
Specification
Conditions
VDD[V]
High level input
IIH(1)
current
Ports 0, 1, 3, 7, 8
• Output disabled
Ports A, B, C
• Pull-up resistor off
Ports D, E, F
• VIN=VDD (Including output Tr's
Port L
RES
VIN=VDD
IIH(3)
XT1, XT2
• For input port specification
2.7 to 3.6
1
2.7 to 3.6
1
15
VIN=VDD
2.7 to 3.6
IIH(5)
P87 small signal
input side
VIN=VBIS+0.5V
(VBIS: Bias voltage)
2.7 to 3.6
Ports 0, 1, 3, 7, 8
• Output disabled
Ports A, B, C
• Pull-up resistor off
Ports D, E, F
• VIN=VSS (Including output Tr's
Port L
1.5
5.5
10
µA
2.7 to 3.6
-1
2.7 to 3.6
-1
2.7 to 3.6
-1
off leakage current)
IIL(2)
RES
VIN=VSS
IIL(3)
XT1, XT2
• For input port specification
• VIN=VSS
IIL(4)
CF1
VIN=VSS
2.7 to 3.6
-15
IIL(5)
P87 small signal
VIN=VBIS-0.5V
(VBIS : Bias voltage)
2.7 to 3.6
-10
input side
unit
1
CF1
current
max
2.7 to 3.6
IIH(4)
IIL(1)
typ
off leakage current)
IIH(2)
• VIN=VDD
Low level input
min
-5.5
-1.5
Continued on next page.
No.A1872-15/26
LC87F7DJ2C
Continued from preceding page.
Parameter
High level output
Symbol
VOH(1)
voltage
Pin/Remarks
Ports 0, 1,
IOH=-0.4mA
32 to 35
VDD[V]
min
typ
2.7 to 3.6
VDD-0.4
VOH(2)
Ports 30, 31
IOH=-1.6mA
2.7 to 3.6
VDD-0.4
VOH(3)
Ports 71 to 73
IOH=-0.4mA
2.7 to 3.6
VDD-0.4
VOH(4)
Ports A, B, C
IOH=-0.4mA
2.7 to 3.6
VDD-0.4
Ports D, E, F
Low level output
Specification
Conditions
VOL(1)
voltage
Ports 0, 1,
max
unit
IOL=1.6mA
32 to 35
Ports 30,31
2.7 to 3.6
0.4
2.7 to 3.6
0.4
2.7 to 3.6
0.4
2.7 to 3.6
0.4
(PWM function
output mode)
VOL(2)
Ports 30, 31
IOL=5mA
(Port function
V
output mode)
VOL(3)
Ports 7, 8
IOL=1.6mA
XT2
VOL(4)
Ports A, B, C
IOL=1.6mA
Ports D, E, F
LCD output voltage
VODLS
S0 to S53
regulation
• IO=0mA
• VLCD, 2/3VLCD,1/3VLCD
level output
2.7 to 3.6
0
±0.2
2.7 to 3.6
0
±0.2
• See Fig. 8.
VODLC
COM0 to COM3
• IO=0mA
• VLCD, 2/3VLCD,1/2VLCD,
1/3VLCD level output
• See Fig. 8.
LCD bias resistor
RLCD(1)
Resistance per
See Fig. 8.
one bias resister
RLCD(2)
Resistance per
2.7 to 3.6
60
2.7 to 3.6
30
See Fig. 8.
one bias resister
kΩ
1/2 mode
Resistance of
Rpu(1)
pull-up MOS Tr.
Ports 0, 1, 3, 7
VOH=0.9VDD
Ports A, B, C
2.7 to 3.6
18
50
150
Ports D, E, F
Hysterisis voltage
VHYS(1)
Ports 1, 7
RES
VHYS(2)
P87 small signal
CP
All pins
0.1VDD
2.7 to 3.6
0.1VDD
2.7 to 3.6
10
V
input side
Pin capacitance
2.7 to 3.6
• For pins other than that
under test: VIN=VSS
• f=1MHz
pF
• Ta=25°C
Input sensitivity
Vsen
P87 small signal
input side
2.7 to 3.6
0.12VDD
Vp-p
No.A1872-16/26
LC87F7DJ2C
Serial I/O Characteristics at Ta = -40°C to +85°C, VSS1 = VSS2 = VSS3 = 0V
1. SIO0 Serial I/O Characteristics (Note 4-1-1) at VDD=2.7V to 3.6V, 0.190μs≤tCYC≤200μs
Parameter
Symbol
Pin/Remarks
Specification
Conditions
Input clock
VDD[V]
Frequency
tSCK(1)
Low level
tSCKL(1)
SCK0(P12)
See Fig. 6.
tSCKH(1)
2.7 to 3.6
pulse width
tSCKHA(1)
tCYC
4
• (Note 4-1-2)
Frequency
tSCK(2)
SCK0(P12)
• CMOS output selected
4/3
• See Fig. 6.
Output clock
Low level
tSCKL(2)
1/2
pulse width
High level
tSCK
tSCKH(2)
2.7 to 3.6
pulse width
tSCKHA(2)
1/2
• Continuous data
transmission/reception mode
tSCKH(2)
• CMOS output selected
+2tCYC
• See Fig. 6.
Data setup time
Serial input
unit
1
• Continuous data
transmission/reception mode
tsDI(1)
SB0(P11),
SI0(P11)
Data hold time
+(10/3)
tCYC
tCYC
0.03
respect to rising edge of
• See Fig. 6.
thDI(1)
tSCKH(2)
• Must be specified with
SIOCLK.
2.7 to 3.6
0.03
Input clock
Output delay
tdD0(1)
time
SO0(P10),
SB0(P11)
• Continuous data
(1/3)tCYC
transmission/reception mode
+0.05
• (Note 4-1-3)
tdD0(2)
• Synchronous 8-bit mode
tdD0(3)
μs
1tCYC
• (Note 4-1-3)
2.7 to 3.6
Output clock
Serial output
max
1
• See Fig. 6.
Serial clock
typ
2
pulse width
High level
min
+0.05
(Note 4-1-3)
(1/3)tCYC
+0.05
Note 4-1-1: These specifications are theoretical values. Add margin depending on its use.
Note 4-1-2: To use serial-clock-input in continuous trans/rec mode, a time from SI0RUN being set when serial clock
is "H" to the first negative edge of the serial clock must be longer than tSCKHA.
Note 4-1-3: Must be specified with respect to falling edge of SIOCLK. Must be specified as the time to the beginning
of output state change in open drain output mode. See Fig. 6.
No.A1872-17/26
LC87F7DJ2C
2. SIO1 Serial I/O Characteristics (Note 4-2-1)
Parameter
Symbol
Pin/Remarks
Specification
Conditions
Input clock
Frequency
tSCK(3)
Low level
tSCKL(3)
SCK1(P15)
typ
See Fig. 6.
tCYC
1
SCK1(P15)
tSCK(4)
• CMOS output selected
2
• See Fig. 6.
Low level
tSCKL(4)
2.7 to 3.6
pulse width
High level
1/2
tSCK
tSCKH(4)
1/2
pulse width
Serial input
Data setup time
SB1(P14),
tsDI(2)
SI1(P14)
• Must be specified with
respect to rising edge of
SIOCLK.
• See Fig. 6.
thDI(2)
Data hold time
unit
1
tSCKH(3)
Frequency
max
2
2.7 to 3.6
pulse width
High level
min
pulse width
Output clock
Serial clock
VDD[V]
0.03
2.7 to 3.6
0.03
Output delay time
tdD0(4)
SO1(P13),
Serial output
SB1(P14)
• Must be specified with
μs
respect to falling edge of
SIOCLK.
• Must be specified as the
time to the beginning of output
(1/3)tCYC
2.7 to 3.6
+0.05
state change in open drain
output mode.
• See Fig. 6.
Note 4-2-1: These specifications are theoretical values. Add margin depending on its use.
Pulse Input Conditions at Ta = -40°C to +85°C, VSS1 = VSS2 = VSS3 = 0V
Parameter
Symbol
Pin/Remarks
Specification
Conditions
VDD[V]
High/low level
tPIH(1)
INT0(P70),
• Interrupt source flag can be set.
pulse width
tPIL(1)
INT1(P71),
• Event inputs for timer 0 or 1
INT2(P72),
min
typ
max
unit
are enabled.
INT4(P30 to P33),
2.7 to 3.6
1
2.7 to 3.6
2
2.7 to 3.6
64
2.7 to 3.6
256
2.7 to 3.6
1
2.7 to 3.6
4
2.7 to 3.6
200
INT5(P34 to P35),
INT6(P30),
INT7(P34)
tPIH(2)
INT3(P73) when
• Interrupt source flag can be set.
tPIL(2)
noise filter time
• Event inputs for timer 0 are
constant is 1/1
tPIH(3)
INT3(P73) when
• Interrupt source flag can be set.
tPIL(3)
noise filter time
• Event inputs for timer 0 are
constant is 1/32
enabled.
tPIH(4)
INT3(P73) when
• Interrupt source flag can be set.
tPIL(4)
noise filter time
• Event inputs for timer 0 are
constant is 1/128
tPIH(5)
MICIN(P87)
tPIL(5)
tPIH(6)
tPIL(7)
enabled.
Condition that signal is accepted to
small signal detection counter.
RMIN(P73)
tPIL(6)
Condition that signal is accepted to
remote control receiver circuit.
RES
tCYC
enabled.
Resetting is enabled.
RMCK
(Note5-1)
μs
Note 5-1: RMCK is an unit for the base clock (40tCYC/50tCYC/Sub-Clock) of remote control receiver circuit.
No.A1872-18/26
LC87F7DJ2C
AD Converter Characteristics at VSS1 = VSS2 = VSS3 =0V
<12bits AD Converter Mode at Ta =-30 to +70°C>
Parameter
Symbol
Pin/Remarks
Specification
Conditions
VDD[V]
Resolution
N
AN0(P80) to
Absolute
ET
AN7(P87),
Conversion
AN9(P71),
tCAD
time
Analog input
typ
2.7 to 3.6
(Note 6-1)
• See Conversion time calculation
AN10(XT1),
formulas.
AN11(XT2)
(Note 6-2)
max
VAIN
voltage range
unit
12
bit
±16
2.7 to 3.6
AN8(P70),
accuracy
min
2.9 to 3.6
32
115
2.7 to 3.6
45
115
2.7 to 3.6
VSS
VDD
Analog port
IAINH
VAIN=VDD
2.7 to 3.6
input current
IAINL
VAIN=VSS
2.7 to 3.6
1
-1
LSB
μs
V
μA
<8bits AD Converter Mode at Ta =-30 to +70°C>
Parameter
Symbol
Pin/Remarks
Specification
Conditions
VDD[V]
Resolution
N
AN0(P80) to
Absolute
ET
AN7(P87),
Conversion
TCAD
time
Analog input
AN9(P71),
typ
2.7 to 3.6
(Note 6-1)
• See Conversion time calculation
AN10(XT1),
formulas.
AN11(XT2)
(Note 6-2)
max
VAIN
voltage range
unit
8
bit
2.7 to 3.6
AN8(P70),
accuracy
min
1.5
2.7 to 3.6
20.00
90
2.7 to 3.6
34.27
90
2.7 to 3.6
VSS
VDD
Analog port
IAINH
VAIN=VDD
2.7 to 3.6
input current
IAINL
VAIN=VSS
2.7 to 3.6
1
-1
LSB
μs
V
μA
<Conversion time calculation formulas>
12bits AD Converter Mode: TCAD(Conversion time)=((52/(division ratio)) + 2) × (1/3) ×tCYC
8bits AD Converter Mode: TCAD(Conversion time)=((32/(division ratio)) + 2) × (1/3) ×tCYC
<Recommended Operating Conditions>
External
Operating supply
oscillation
voltage range
FmCF [MHz]
VDD [V]
20
15
System division ratio
Cycle time
(SYSDIV)
tCYC [ns]
2.9 to 3.6
1/1
2.7 to 3.6
1/1
AD division
AD conversion time
(tCAD) [μs]
ratio
(ADDIV)
12bit AD
150
1/16
41.70
25.70
200
1/16
55.6
34.27
8bit AD
Note 6-1: The quantization error (±1/2LSB) must be excluded from the absolute accuracy. The absolute accuracy must
be measured in the microcontroller's state in which no I/O operations occur at the pins adjacent to the analog
input channel.
Note 6-2: The conversion time refers to the period from the time an instruction for starting a conversion process till the
time the conversion results register(s) are loaded with a complete digital conversion value corresponding to
the analog input value.
The conversion time is 2 times the normal-time conversion time when:
• The first AD conversion is performed in the 12-bit AD conversion mode after a system reset.
• The first AD conversion is performed after the AD conversion mode is switched from 8-bit to 12-bit
conversion mode.
No.A1872-19/26
LC87F7DJ2C
Consumption Current Characteristics at Ta = -40°C to +85°C, VSS1 = VSS2 = VSS3 = 0V
Parameter
Symbol
Pin/
Remarks
VDD[V]
• FmCF=15MHz ceramic oscillation mode
consumption
VDD1
=VDD2
current
=VDD3
• System clock set to 12MHz side
Normal mode
IDDOP(1)
(Note 7-1)
Specification
Conditions
min
typ
max
unit
• FmX’tal=32.768kHz crystal oscillation mode
• Internal RC oscillation stopped.
2.7 to 3.6
6.1
15.6
2.7 to 3.6
0.4
1.7
• Frequency variable RC oscillation stopped.
• 1/1 frequency division ratio
IDDOP(2)
• FmCF=0Hz (oscillation stopped)
• FmX’tal=32.768kHz crystal oscillation mode
• System clock set to internal RC oscillation
• Frequency variable RC oscillation stopped.
• 1/2 frequency division ratio
IDDOP(3)
mA
• FmCF=0Hz (oscillation stopped)
• FmX’tal=32.768kHz crystal oscillation mode
• Internal RC oscillation stopped.
• System clock set to 10MHz with
2.7 to 3.6
4.3
12.0
2.7 to 3.6
2.1
6.6
2.7 to 3.6
19.3
73
frequency variable RC oscillation
• 1/1 frequency division ratio
IDDOP(4)
• FmCF=0Hz (oscillation stopped)
• FmX’tal=32.768kHz crystal oscillation mode
• Internal RC oscillation stopped.
• System clock set to 4MHz with
frequency variable RC oscillation
• 1/1 frequency division ratio
IDDOP(5)
• FmCF=0Hz (oscillation stopped)
• FmX’tal=32.768kHz crystal oscillation mode
• System clock set to 32.768kHz side
• Internal RC oscillation stopped.
μA
• Frequency variable RC oscillation stopped.
• 1/2 frequency division ratio
Note 7-1: The consumption current value includes none of the currents that flow into the output Tr and internal pull-up
resistors.
Continued on next page.
No.A1872-20/26
LC87F7DJ2C
Continued from preceding page.
Parameter
HALT mode
Symbol
IDDHALT(1)
Pin/
VDD[V]
• HALT mode
consumption
VDD1
=VDD2
current
=VDD3
• FmX’tal=32.768kHz crystal oscillation mode
(Note 7-1)
Specification
Conditions
Remarks
min
typ
max
unit
• FmCF=12MHz ceramic oscillation mode
• System clock set to 12MHz side
2.7 to 3.6
2.7
6.8
2.7 to 3.6
0.2
0.75
• Internal RC oscillation stopped.
• Frequency variable RC oscillation stopped.
• 1/1 frequency division ratio
IDDHALT(2)
• HALT mode
• FmCF=0Hz (oscillation stopped)
• FmX’tal=32.768kHz crystal oscillation mode
• System clock set to internal RC oscillation
• Frequency variable RC oscillation stopped.
• 1/2 frequency division ratio
IDDHALT(3)
mA
• HALT mode
• FmCF=0Hz (oscillation stopped)
• FmX’tal=32.768kHz crystal oscillation mode
• Internal RC oscillation stopped.
2.7 to 3.6
1.6
4.6
2.7 to 3.6
0.7
1.75
2.7 to 3.6
12.4
54.9
• System clock set to 10MHz with
frequency variable RC oscillation
• 1/1 frequency division ratio
IDDHALT(4)
• HALT mode
• FmCF=0Hz (oscillation stopped)
• FmX’tal=32.768kHz crystal oscillation mode
• Internal RC oscillation stopped.
• System clock set to 4MHz with
frequency variable RC oscillation
• 1/1 frequency division ratio
• HALT mode
IDDHALT(5)
• FmCF=0Hz (oscillation stopped)
• FmX’tal=32.768kHz crystal oscillation mode
• System clock set to 32.768kHz side
• Internal RC oscillation stopped.
• Frequency variable RC oscillation stopped.
• 1/2 frequency division ratio
HOLD mode
IDDHOLD(1)
VDD1
consumption
μA
• HOLD mode
• CF1=VDD or open (External clock mode)
2.7 to 3.6
0.06
18.4
2.7 to 3.6
10.14
34.4
current
Timer HOLD
IDDHOLD(2)
VDD1
• Timer HOLD mode
mode
• CF1=VDD or open (External clock mode)
consumption
• FmX’tal=32.768kHz crystal oscillation mode
current
Note 7-1: The consumption current value includes none of the currents that flow into the output Tr and internal pull-up
resistors.
No.A1872-21/26
LC87F7DJ2C
F-ROM Write Characteristics at Ta = +10°C to +55°C, VSS1 = VSS2 = VSS3 = 0V
Parameter
Onboard
Symbol
IDDFW(1)
Pin/Rem
VDD1
programming
Specification
Conditions
arks
VDD[V]
min
typ
max
unit
• 128-byte programming
• Erasing current included
3.0 to 3.6
mA
3.0 to 3.6
ms
current
Programming
tFW(1)
• 128-byte programming
time
• Erasing current included
• Time for setting up 128-byte data is
excluded.
UART (Full Duplex) Operating Conditions at Ta = -40 to +85°C, VSS1 = VSS2 = VSS3 = 0V
Parameter
Symbol
Pin/Remarks
Specification
Conditions
VDD[V]
Transfer ate
UBR
UTX(P32),
2.7 to 3.6
URX(P33)
min
typ
max
16/3
8192/3
unit
tCYC
Data length: 7/8/9 bits (LSB first)
Stop bits:
1 bit (2-bit in continuous data transmission)
Parity bits: None
Example of 8-bit Data Transmission Mode Processing (Transmit Data=55H)
Start bit
Start of
transmission
Stop bit
Transmit data (LSB first)
End of
transmission
UBR
Example of 8-bit Data Reception Mode Processing (Receive Data=55H)
Stop bit
Start bit
Start of
reception
Receive data (LSB first)
End of
reception
UBR
No.A1872-22/26
LC87F7DJ2C
Characteristics of a Sample Main System Clock Oscillation Circuit
Given below are the characteristics of a sample main system clock oscillation circuit that are measured using a
SANYO-designated oscillation characteristics evaluation board and external components with circuit constant values
with which the oscillator vendor confirmed normal and stable oscillation.
Table 1 Characteristics of a Sample Main System Clock Oscillator Circuit with a Ceramic Oscillator
Nominal
Vendor
Frequency
Name
20MHz
Circuit Constant
Oscillator Name
Operating
Oscillation
Voltage
Stabilization Time
C1
C2
Rf1
Rd1
Range
typ
max
[pF]
[pF]
[Ω]
[Ω]
[V]
[ms]
[ms]
CSTCE20M0V51-R0
(5)
(5)
Open
150
2.7 to 3.6
0.05
0.15
CSTLS20M0X51-B0
(5)
(5)
Open
0
2.7 to 3.6
0.05
0.15
Remarks
Values shown in
parentheses are
capacitance included
in the oscillator
MURATA
The oscillation stabilization time refers to the time interval that is required for the oscillation to get stabilized after VDD
goes above the operating voltage lower limit (see Figure 4).
Characteristics of a Sample Subsystem Clock Oscillator Circuit
Given below are the characteristics of a sample subsystem clock oscillation circuit that are measured using a SANYOdesignated oscillation characteristics evaluation board and external components with circuit constant values with which
the oscillator vendor confirmed normal and stable oscillation.
Table 2 Characteristics of a Sample Subsystem Clock Oscillator Circuit with a Crystal Oscillator
Nominal
Vendor Name
Frequency
Operating
Circuit Constant
Oscillator
Name
C3
C4
Rf2
Rd2
[pF]
[pF]
[Ω]
[Ω]
Voltage Range
[V]
Oscillation
Stabilization Time
typ
max
[s]
[s]
Remarks
32.768kHz
The oscillation stabilization time refers to the time interval that is required for the oscillation to get stabilized after the
instruction for starting the subclock oscillation circuit is executed and to the time interval that is required for the
oscillation to get stabilized after the HOLD mode is reset (see Figure 4).
Note: The components that are involved in oscillation should be placed as close to the IC and to one another as possible
because they are vulnerable to the influences of the circuit pattern.
CF1
XT1
CF2
Rf1
Rf2
Rd1
C1
C2
XT2
Rd2
C3
C4
CF
X’tal
Figure 1 CF Oscillator Circuit
Figure 2 XT Oscillator Circuit
No.A1872-23/26
LC87F7DJ2C
0.5VDD
Figure 3 AC Timing Measurement Point
VDD
Operating VDD
lower limit
0V
Power supply
Reset time
RES
Internal RC
oscillation
tmsCF
CF1, CF2
tmsX’tal
XT1, XT2
Operating mode
Reset
Unpredictable
Instruction execution
Reset Time and Oscillation Stabilization Time
HOLD reset signal
HOLD reset signal
absent
HOLD reset signal VALID
Internal RC
oscillation
tmsCF
CF1, CF2
tmsX’tal
XT1, XT2
State
HOLD
HALT
HOLD Reset Signal and Oscillation Stabilization Time
Figure 4 Oscillation Stabilization Times
No.A1872-24/26
LC87F7DJ2C
VDD
Note:
Determine the value of CRES and RRES so that the
reset signal is present for a period of 200μs after the
supply voltage goes beyond the lower limit of the IC's
operating voltage.
RRES
RES
CRES
Figure 5 Reset Circuit
SIOCLK:
DATAIN:
DI0
DI1
DI2
DI3
DI4
DI5
DI6
DATAOUT:
DO0
DO1
DO2
DO3
DO4
DO5
DO6
DI7
DI8
DO7
DO8
Data RAM
transfer period
(SIO0 only)
tSCK
tSCKH
tSCKL
SIOCLK:
tsDI
thDI
DATAIN:
tdDO
DATAOUT:
Data RAM
transfer period
(SIO0 only)
tSCKL
tSCKHA
SIOCLK:
tsDI
thDI
DATAIN:
tdDO
DATAOUT:
Figure 6 Serial I/O Waveforms
tPIL
tPIH
Figure 7 Pulse Input Timing Signal Waveform
No.A1872-25/26
LC87F7DJ2C
VDD
SW : ON/OFF (programmable)
RLCD
RLCD
SW: ON (VLCD=VDD)
RLCD
RLCD
VLCD
RLCD
RLCD
2/3VLCD
RLCD
1/2VLCD
RLCD
1/3VLCD
RLCD
RLCD
GND
Figure 8 LCD Bias Resistor
SANYO Semiconductor Co.,Ltd. assumes no responsibility for equipment failures that result from using
products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition
ranges, or other parameters) listed in products specifications of any and all SANYO Semiconductor Co.,Ltd.
products described or contained herein.
SANYO Semiconductor Co.,Ltd. strives to supply high-quality high-reliability products, however, any and all
semiconductor products fail or malfunction with some probability. It is possible that these probabilistic failures or
malfunction could give rise to accidents or events that could endanger human lives, trouble that could give rise
to smoke or fire, or accidents that could cause damage to other property. When designing equipment, adopt
safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not
limited to protective circuits and error prevention circuits for safe design, redundant design, and structural
design.
In the event that any or all SANYO Semiconductor Co.,Ltd. products described or contained herein are
controlled under any of applicable local export control laws and regulations, such products may require the
export license from the authorities concerned in accordance with the above law.
No part of this publication may be reproduced or transmitted in any form or by any means, electronic or
mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise,
without the prior written consent of SANYO Semiconductor Co.,Ltd.
Any and all information described or contained herein are subject to change without notice due to
product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the
SANYO Semiconductor Co.,Ltd. product that you intend to use.
Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed
for volume production.
Upon using the technical information or products described herein, neither warranty nor license shall be granted
with regard to intellectual property rights or any other rights of SANYO Semiconductor Co.,Ltd. or any third
party. SANYO Semiconductor Co.,Ltd. shall not be liable for any claim or suits with regard to a third party's
intellectual property rights which has resulted from the use of the technical information and products mentioned
above.
This catalog provides information as of October, 2010. Specifications and information herein are subject
to change without notice.
PS No.A1872-26/26