SANYO LC87F5G32A

Ordering number : EN8298B
LC87F5G32A
CMOS IC
FROM 32K byte, RAM 1024 byte on-chip
8-bit 1-chip Microcontroller
Overview
The SANYO LC87F5G32A is an 8-bit microcomputer that, centered around a CPU running at a minimum bus cycle
time of 100ns, integrates on a single chip a number of hardware features such as 32K-byte flash ROM (onboard
programmable), 1024-byte RAM, an on-chip debugger, sophisticated 16-bit timers/counters (may be divided into 8-bit
timers), a 16-bit timer/counter (may be divided into 8-bit timers/counters or 8-bit PWMs), four 8-bit timers with
a prescaler, a base timer serving as a time-of-day clock, a high-speed clock counter, a synchronous SIO interface
(with automatic block transmission/reception capabilities), an asynchronous/synchronous SIO interface, a UART
interface (full duplex), a 12-bit/8-bit 12-channel AD converter, two 12-bit PWM channels, a system clock frequency
divider, and a 22-source 10-vector interrupt feature.
Features
„Flash ROM
• Capable of on-board-programming with wide range, 3.0 to 5.5V, of voltage source.
• Block-erasable in 128 byte units
• 32768 × 8-bits (LC87F5G32A)
„RAM
• 1024 × 9 bits (LC87F5G32A)
„Minimum Bus Cycle
• 100ns (10MHz)
Note : The bus cycle time here refers to the ROM read speed.
„Minimum Instruction Cycle Time
• 300ns (10MHz)
* This product is licensed from Silicon Storage Technology, Inc. (USA), and manufactured and sold by
SANYO Semiconductor Co., Ltd.
Any and all SANYO Semiconductor Co.,Ltd. products described or contained herein are, with regard to
"standard application", intended for the use as general electronics equipment (home appliances, AV equipment,
communication device, office equipment, industrial equipment etc.). The products mentioned herein shall not be
intended for use for any "special application" (medical equipment whose purpose is to sustain life, aerospace
instrument, nuclear control device, burning appliances, transportation machine, traffic signal system, safety
equipment etc.) that shall require extremely high level of reliability and can directly threaten human lives in case
of failure or malfunction of the product or may cause harm to human bodies, nor shall they grant any guarantee
thereof. If you should intend to use our products for applications outside the standard applications of our
customer who is considering such use and/or outside the scope of our intended standard applications, please
consult with us prior to the intended use. If there is no consultation or inquiry before the intended use, our
customer shall be solely responsible for the use.
Specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein stipulate
the performance, characteristics, and functions of the described products in the independent state, and are not
guarantees of the performance, characteristics, and functions of the described products as mounted in the
customer' s products or equipment. To verify symptoms and states that cannot be evaluated in an independent
device, the customer should always evaluate and test devices mounted in the customer' s products or
equipment.
Ver.3.00
52307HKIM 20070123-S00009 No.8298-1/23
LC87F5G32A
„Ports
• Normal withstand voltage I/O ports
Ports whose I/O direction can be designated in 1-bit units 30 (P1n,P2n,P30 to P36,P70 to P73,PWM0,PWM1,XT2)
Ports whose I/O direction can be designated in 4-bit units 8 (P0n)
• Normal withstand voltage input port
1 (XT1)
• Dedicated oscillator ports
2 (CF1, CF2)
• Reset pins
1 (RES)
• Power pins
6 (VSS1 to 3, VDD1 to 3)
„Timers
• Timer 0: 16-bit timer/counter with a capture register.
Mode 0: 8-bit timer with an 8-bit programmable prescaler (with an 8-bit capture register) × 2-channels
Mode 1: 8-bit timer with an 8-bit programmable prescaler (with an 8-bit capture register) + 8-bit counter
(with an 8-bit capture register)
Mode 2: 16-bit timer with an 8-bit programmable prescaler (with a 16-bit capture register)
Mode 3: 16-bit counter (with a 16-bit capture register)
• Timer 1: 16-bit timer/counter that supports PWM/toggle outputs
Mode 0: 8-bit timer with an 8-bit prescaler (with toggle outputs) + with an 8-bit prescaler 8-bit timer/counter
(with toggle outputs)
Mode 1: 8-bit PWM with an 8-bit prescaler × 2-channels
Mode 2: 16-bit timer/counter with an 8-bit prescaler (with toggle outputs)
(toggle outputs also possible from the lower-order 8-bits)
Mode 3: 16-bit timer with an 8-bit prescaler (with toggle outputs)
(the lower-order 8-bits can be used as PWM.)
• Timer 4: 8-bit timer with a 6-bit prescaler
• Timer 5: 8-bit timer with a 6-bit prescaler
• Timer 6: 8-bit timer with a 6-bit prescaler (with toggle outputs)
• Timer 7: 8-bit timer with a 6-bit prescaler (with toggle outputs)
• Base timer
1) The clock is selectable from the subclock (32.768kHz crystal oscillation), system clock, and timer 0 prescaler
output.
2) Interrupts programmable in 5 different time schemes
„High-speed Clock Counter
1) Can count clocks with a maximum clock rate of 20MHz (at a main clock of 10MHz).
2) Can generate output real-time.
„SIO
• SIO0: 8-bit synchronous serial interface
1) LSB first/MSB first mode selectable
2) Built-in 8-bit baudrate generator (maximum transfer clock cycle=4/3 tCYC)
3) Automatic continuous data transmission (1 to 256-bits, specifiable in 1 bit units, suspension and resumption
of data transmission possible in 1 byte units)
• SIO1: 8-bit asynchronous/synchronous serial interface
Mode 0: Synchronous 8-bit serial I/O (2- or 3-wire configuration, 2 to 512 tCYC transfer clocks)
Mode 1: Asynchronous serial I/O (half-duplex, 8 data bits, 1 stop bit, 8 to 2048 tCYC baudrates)
Mode 2: Bus mode 1 (start bit, 8 data bits, 2 to 512 tCYC transfer clocks)
Mode 3: Bus mode 2 (start detect, 8 data bits, stop detect)
„UART
• Full duplex
• 7/8/9 bit data bits selectable
• 1stop bit (2-bit in continuous data transmission)
• Built-in baudrate generator
„AD Converter: 12-bits/8-bits × 12-channels
• 12-bits/8-bits AD converter selectable
• Automatic reference voltage generation controllable
No.8298-2/23
LC87F5G32A
„PWM: Multifrequency 12-bit PWM × 2-channels
„Remote Control Receiver Circuit (sharing pins with P73, INT3, and T0IN)
• Noise rejection function (noise filter time constant selectable from 1 tCYC, 32 tCYC, and 128 tCYC)
„Watchdog Timer
• External RC watchdog timer
• Interrupt and reset signals selectable
„Interrupts
• 22 sources, 10 vector addresses
1) Provides three levels (low (L), high (H), and highest (X)) of multiplex interrupt control. Any interrupt requests of
the level equal to or lower than the current interrupt are not accepted.
2) When interrupt requests to two or more vector addresses occur at the same time, the interrupt of the highest level
takes precedence over the other interrupts. For interrupts of the same level, the interrupt into the smallest vector
address takes precedence.
No.
Vector Address
Level
1
00003H
X or L
INT0
Interrupt Source
2
0000BH
X or L
INT1
3
00013H
H or L
INT2/T0L/INT4
4
0001BH
H or L
INT3/INT5/base timer
5
00023H
H or L
T0H
6
0002BH
H or L
T1L/T1H
7
00033H
H or L
SIO0/UART1 receive
8
0003BH
H or L
SIO1/UART1 transmit
9
00043H
H or L
ADC/T6/T7
10
0004BH
H or L
Port 0/T4/T5/PWM0, PWM1
• Priority Levels: X > H > L
• Of interrupts of the same level, the one with the smallest vector address takes precedence.
„Subroutine Stack Levels: 512 levels (the stack is allocated in RAM.)
„High-speed Multiplication/Division Instructions
• 16-bits × 8-bits
(5 tCYC execution time)
• 24-bits × 16-bits
(12 tCYC execution time)
• 16-bits ÷ 8-bits
(8 tCYC execution time)
• 24-bits ÷ 16-bits
(12 tCYC execution time)
„Oscillation Circuits
• RC oscillation circuit (internal):
• CF oscillation circuit:
• Crystal oscillation circuit:
• Frequency variable RC oscillation circuit (internal):
For system clock
For system clock, with internal Rf
For low-speed system clock, with internal Rf
For system clock
„System Clock Divider Function
• Can run on low current.
• The minimum instruction cycle selectable from 300ns, 600ns, 1.2µs, 2.4µs, 4.8µs, 9.6µs, 19.2µs, 38.4µs, and 76.8µs
(at a main clock rate of 10MHz).
No.8298-3/23
LC87F5G32A
„Standby Function
• HALT mode : Halts instruction execution while allowing the peripheral circuits to continue operation.
1) Oscillation is not halted automatically.
2) Canceled by a system reset or occurrence of an interrupt.
• HOLD mode : Suspends instruction execution and the operation of the peripheral circuits.
1) The CF, RC, and crystal oscillators automatically stop operation.
2) There are three ways of resetting the HOLD mode.
(1) Setting the reset pin to the lower level.
(2) Setting at least one of the INT0, INT1, INT2, INT4, and INT5 pins to the specified level.
(3) Having an interrupt source established at port 0.
• X'tal HOLD mode : Suspends instruction execution and the operation of the peripheral circuits except the base timer.
1) The CF and RC oscillators automatically stop operation.
2) The state of crystal oscillation established when the X'tal HOLD mode is entered is retained.
3) There are four ways of resetting the X'tal HOLD mode.
(1) Setting the reset pin to the low level.
(2) Setting at least one of the INT0, INT1, INT2, INT4, and INT5 pins to the specified level.
(3) Having an interrupt source established at port.
(4) Having an interrupt source established in the base timer circuit.
„Onchip Debugger
• Supports software debugging with the IC mounted on the target board.
„Package Form
• QIP48E(14×14): “Lead-free type”
• SQFP48(7×7): “Lead-free type”
„Development Tools
• Evaluation chip: LC87EV690
• Emulator:
EVA62S + ECB876600D + SUB875G00 + POD48QFP
ICE-B877300 + SUB875G00 + POD48QFP
• Onchip debugger: TCB87 TypeA + LC87F5G32A
TCB87 TypeB + LC87F5G32A
„Flash ROM Programming boards
Package
Programming boards
QIP48E(14×14)
W87F55256Q
SQFP48(7×7)
W87F55256SQ
„Flash ROM programmer
Maker
Model
Single
Flash Support Group, Inc.
(Formerly Ando Electric Co., Ltd.)
Gang
AF9708/AF9709/
AF9709B
AF9723 (Main body)
AF9833 (Unit)
SANYO
SKK (SANYO FWS)
Supported version (Note)
Device
After 02.40
After 02.04
LC87F5G32A FAST
After 01.84
After 1.02C (Install CD)
LC87F5G32A
Note: Please check the latest version.
„Same package and pin assignment as mask ROM version.
1) LC875G00 series options can be set by using flash ROM data. Thus the board used for mass production can be
used for debugging and evaluation without modifications.
2) If the program for the mask ROM version is used, the usable ROM/RAM capacity is the same as the mask ROM
version.
No.8298-4/23
LC87F5G32A
Package Dimensions
Package Dimensions
unit : mm (typ)
3156A
unit : mm (typ)
3163B
0.8
14.0
25
36
36
0.5
9.0
7.0
17.2
25
37
24
48
13
24
17.2
14.0
7.0
9.0
37
13
48
1
12
0.5
1
0.15
(0.75)
12
1.0
0.18
0.15
0.35
3.0max
(1.5)
0.1
(2.7)
1.7max
(1.5)
0.1
SANYO : SQFP48(7X7)
SANYO : QIP48E(14X14)
36
35
34
33
32
31
30
29
28
27
26
25
P27/INT5/T1IN
P26/INT5/T1IN
P25/INT5/T1IN
P24/INT5/T1IN
P23/INT4/T1IN
P22/INT4/T1IN
P21/URX/INT4/T1IN
P20/UTX/INT4/T1IN
P07/T7O/AN7
P06/T6O/AN6
P05/CKO/AN5
P04/AN4
Pin Assignment
LC87F5G32A
24
23
22
21
20
19
18
17
16
15
14
13
P03/AN3
P02/AN2
P01/AN1
P00/AN0
VSS2
VDD2
PWM0
PWM1
P17/T1PWMH/BUZ
P16/T1PWML
P15/SCK1
P14/SI1/SB1
1
2
3
4
5
6
7
8
9
10
11
12
37
38
39
40
41
42
43
44
45
46
47
48
P73/INT3/T0IN
RES
XT1/AN10
XT2/AN11
VSS1
CF1
CF2
VDD1
P10/SO0
P11/SI0/SB0
P12/SCK0
P13/SO1
P36
P35
VDD3
VSS3
P34
P33
P32/DBGP2
P31/DBGP1
P30/DBGP0
P70/INT0/T0LCP/AN8
P71/INT1/T0HCP/AN9
P72/INT2/T0IN
Top view
SANYO: QIP48E(14×14) "Lead-free Type"
SANYO: SQFP48(7×7) "Lead-free Type"
No.8298-5/23
LC87F5G32A
SQFP/QIP
NAME
SQFP/QIP
NAME
1
P73/INT3/T0IN
25
P04/AN4
2
RES
26
P05/CKO/AN5
3
XT1/AN10
27
P06/T6O/AN6
4
XT2/AN11
28
P07/T7O/AN7
5
VSS1
29
P20/UTX/INT4/T1IN
6
CF1
30
P21/URX/INT4/T1IN
7
CF2
31
P22/INT4/T1IN
8
VDD1
32
P23/INT4/T1IN
9
P10/SO0
33
P24/INT5/T1IN
10
P11/SI0/SB0
34
P25/INT5/T1IN
11
P12/SCK0
35
P26/INT5/T1IN
12
P13/SO1
36
P27/INT5/T1IN
13
P14/SI1/SB1
37
P36
14
P15/SCK1
38
P35
15
P16/T1PWML
39
VDD3
16
P17/T1PWMH/BUZ
40
VSS3
17
PWM1
41
P34
18
PWM0
42
P33
19
VDD2
43
P32/DBGP2
20
VSS2
44
P31/DBGP1
21
P00/AN0
45
P30/DBGP0
22
P01/AN1
46
P70/INT0/T0LCP/AN8
23
P02/AN2
47
P71/INT1/T0HCP/AN9
24
P03/AN3
48
P72/INT2/T0IN
No.8298-6/23
LC87F5G32A
System Block Diagram
Interrupt control
IR
Standby control
PLA
Flash ROM
RC
X’tal
Clock
generator
CF
PC
MRC
SIO0
Bus interface
ACC
SIO1
Port 0
B register
Timer 0
Port 1
C register
Timer 1
Port 3
ALU
Timer 4
Port 7
Timer 5
ADC
PSW
Timer 6
INT0-2, INT4,5
INT3 (Noise filter)
RAR
Timer 7
Port 2
RAM
Base timer
UART1
Stack pointer
PWM0
Watchdog timer
PWM1
On-chip debugger
No.8298-7/23
LC87F5G32A
Pin Function Chart
Pin Name
VSS1
VSS2
I/O
Description
Option
-
- Power supply pin
Yes
-
+ Power supply pin
No
• 8-bit I/O port
Yes
VSS3
VDD1
VDD2
VDD3
Port 0
I/O
• I/O specifiable in 4-bit units
P00 to P07
• Pull-up resistors can be turned on and off in 4-bit units
• HOLD reset input
• Port 0 interrupt input
• Shared pins
P05: System clock output
P06: Timer 6 toggle output
P07: Timer 7 toggle output
AD converter input port: AN0 (P00) to AN7 (P07)
Port 1
I/O
• 8-bit I/O port
Yes
• I/O specifiable in 1-bit units
P10 to P17
• Pull-up resistors can be turned on and off in 1-bit units
• Pin functions
P10: SIO0 data output
P11: SIO0 data input/bus I/O
P12: SIO0 clock I/O
P13: SIO1 data output
P14: SIO1 data input/bus I/O
P15: SIO1 clock I/O
P16: Timer 1PWML output
P17: Timer 1PWMH output/beeper output
Port 2
P20 to P27
I/O
Yes
• 8-bit I/O port
• I/O specifiable in 1-bit units
• Pull-up resistors can be turned on and off in 1-bit units
• Pin functions
P20: UART transmit
P21: UART receive
P20 to P23: INT4 input/HOLD reset input/timer 1 event input/
timer 0L capture input/timer 0H capture input
P24 to P27: INT5 input/HOLD reset input/timer 1 event input/
timer 0L capture input/timer 0H capture input
Interrupt acknowledge type
Rising
Falling
INT4
enable
enable
INT5
enable
enable
Rising &
H level
L level
enable
disable
disable
enable
disable
disable
Falling
Continued on next page.
No.8298-8/23
LC87F5G32A
Continued from preceding page.
Pin Name
Port 3
I/O
I/O
Description
Option
• 7-bit I/O port
Yes
• I/O specifiable in 1-bit units
P30 to P36
• Pull-up resistors can be turned on and off in 1-bit units
• Shared pins
On-chip debugger pins: DBGP0 to DBGP2 (P30 to P32)
Port 7
I/O
No
• 4-bit I/O port
• I/O specifiable in 1-bit units
P70 to P73
• Pull-up resistors can be turned on and off in 1-bit units
• Shared pins
AD converter input port : AN8 (P70), AN9 (P71)
P70: INT0 input/HOLD reset input/timer 0L capture input/watchdog timer output
P71: INT1 input/HOLD reset input/timer 0H capture input
P72: INT2 input/HOLD reset input/timer 0 event input/timer 0L capture input
P73: INT3 input (with noise filter)/timer 0 event input/timer 0H capture input
Interrupt acknowledge type
PWM0, PWM1
I/O
Rising
Falling
INT0
enable
enable
INT1
enable
enable
INT2
enable
INT3
enable
Rising &
H level
L level
disable
enable
enable
disable
enable
enable
enable
enable
disable
disable
enable
enable
disable
disable
Falling
• PWM0 and PWM1 output ports
No
• General-purpose I/O available
RES
Input
Reset pin
No
XT1
Input
• 32.768kHz crystal oscillator input pin
No
• Shared pins
General-purpose input port
AD converter input port: AN10
Must be connected to VDD1 if not to be used
XT2
I/O
• 32.768kHz crystal oscillator output pin
No
• Shared pins
General-purpose I/O port
AD converter input port: AN11
Must be set for oscillation and kept open if not to be used
CF1
Input
CF2
Output
Ceramic resonator input pin
No
Ceramic resonator output pin
No
No.8298-9/23
LC87F5G32A
Port Output Types
The table below lists the types of port outputs and the presence/absence of a pull-up resistor.
Data can be read into any input port even if it is in the output mode.
Port Name
Option Selected in
Units of
Option Type
P00 to P07
1-bit
1
P10 to P17
1-bit
Output Type
Pull-up Resistor
CMOS
Programmable (Note 1)
2
Nch-open drain
No
1
CMOS
Programmable
2
Nch-open drain
Programmable
1
CMOS
Programmable
2
Nch-open drain
Programmable
1-bit
1
CMOS
Programmable
2
Nch-open drain
Programmable
P70
-
No
Nch-open drain
Programmable
P71 to P73
-
No
CMOS
Programmable
P20 to P27
P30 to P36
1-bit
PWM0, PWM1
-
No
CMOS
No
XT1
-
No
Input for 32.768kHz crystal oscillator
No
(Input only)
XT2
-
No
Output for 32.768kHz crystal oscillator
No
(Nch-open drain when in general-purpose
output mode)
Note 1: Programmable pull-up resistor of Port 0 is specified in nibble units (P00 to P03, P04 to P07).
Note: To reduce VDD signal noise and to increase the duration of the backup battery supply, VSS1, VSS2,
and VSS3 should connect to each other and they should also be grounded.
Example 1: During backup in hold mode, port output ‘H’ level is supplied from the back-up capacitor.
Back-up
capacitor
Power
Supply
LSI
VDD1
VDD2
VDD3
VSS1 VSS2 VSS3
Example 2: During backup in hold mode, output is not held high and its value in unsettled.
Back-up
capacitor
Power
Supply
LSI
VDD1
VDD2
VDD3
VSS1 VSS2 VSS3
No.8298-10/23
LC87F5G32A
Absolute Maximum Ratings at Ta = 25°C, VSS1 = VSS2 = VSS3 = 0V
Parameter
Symbol
Pin/Remarks
Specification
Conditions
VDD[V]
Maximum supply
VDD max
VDD1, VDD2,
VDD3
Input voltage
VI
XT1, CF1
Input/output
VIO
Ports 0, 1, 2, 3
voltage
voltage
VDD1=VDD2=VDD3
Port 7, PWM0,
min
typ
max
unit
-0.3
+6.5
-0.3
VDD+0.3
-0.3
VDD+0.3
V
PWM1, XT2
Peak output
IOPH(1)
Ports 0, 1, 2, 3
current
CMOS output select
Per 1 applicable pin
IOPH(2)
PWM0, PWM1
CMOS output select
Per 1 applicable pin
High level output current
Mean output
IOPH(3)
Ports P71 to P73
Per 1 applicable pin
IOMH(1)
Ports 0, 1, 2, 3
CMOS output select
current
(Note 1-1)
Per 1 applicable pin
IOMH(2)
PWM0, PWM1
CMOS output select
Per 1 applicable pin
-10
-20
-5
-7.5
-15
IOMH(3)
Ports P71 to P73
Per 1 applicable pin
Total output
ΣIOAH(1)
Ports P71 to P73
Total of all applicable pins
-10
current
ΣIOAH(2)
Port 0
Total of all applicable pins
-25
ΣIOAH(3)
Ports 1,
Total of all applicable pins
PWM0, PWM1
ΣIOAH(4)
Ports 0, 1
Total of all applicable pins
PWM0, PWM1
Peak output
-3
-25
-45
ΣIOAH(5)
Ports 2, P35, P36
Total of all applicable pins
-25
ΣIOAH(6)
Ports P30 to P34
Total of all applicable pins
-25
-45
ΣIOAH(7)
Ports 2, 3
Total of all applicable pins
IOPL(1)
Ports P02 to P07
Per 1 applicable pin
current
mA
Ports 1, 2, 3
20
PWM0, PWM1
Low level output current
Mean output
IOPL(2)
Ports P00, P01
Per 1 applicable pin
30
IOPL(3)
IOML(1)
Port 7, XT2
Per 1 applicable pin
10
Ports P02 to P07
Per 1 applicable pin
current
Ports 1, 2, 3
(Note 1-1)
PWM0, PWM1
IOML(2)
15
Ports P00, P01
Per 1 applicable pin
20
IOML(3)
Port 7, XT2
Per 1 applicable pin
7.5
Total output
ΣIOAL(1)
Port 7, XT2
Total of all applicable pins
15
current
ΣIOAL(2)
Port 0
Total of all applicable pins
45
ΣIOAL(3)
Ports 1,
Total of all applicable pins
45
PWM0, PWM1
ΣIOAL(4)
Ports 0, 1
Total of all applicable pins
80
PWM0, PWM1
Power dissipation
ΣIOAL(5)
Ports 2, P35, P36
Total of all applicable pins
ΣIOAL(6)
Ports P30 to P34
Total of all applicable pins
ΣIOAL(7)
Ports 2, 3
Total of all applicable pins
Pd max
SQFP48(7×7)
Ta= -30 to +70°C
45
45
60
190
QIP48E(14×14)
Operating ambient
Topr
temperature
Storage ambient
Tstg
temperature
mW
390
-30
+70
-55
+125
°C
Note 1-1: The mean output current is a mean value measured over 100ms.
No.8298-11/23
LC87F5G32A
Allowable Operating Conditions at at Ta = -30°C to +70°C, VSS1 = VSS2 = VSS3 = 0V
Parameter
Symbol
Pin/Remarks
Specification
VDD[V]
0.294µs ≤ tCYC ≤ 200µs
min
typ
max
unit
Operating
VDD(1)
supply voltage
VDD(2)
0.367µs ≤ tCYC ≤ 200µs
3.0
5.5
VDD(3)
0.588µs ≤ tCYC ≤ 200µs
2.5
5.5
2.0
5.5
(Note 2-1)
Memory
VHD
VDD1=VDD2=VDD3
Conditions
VDD1=VDD2=VDD3
4.0
RAM and register contents
sustained in HOLD mode.
sustaining
5.5
supply voltage
High level input
VIH(1)
voltage
Ports 1, 2, 3
P71 to P73
2.5 to 5.5
P70 port input/
interrupt side
0.3VDD
VDD
+0.7
PWM0, PWM1
VIH(2)
VIH(3)
Port 0
2.5 to 5.5
Port 70 watchdog
timer side
Low level input
VIH(4)
XT1, XT2, CF1, RES
VIL(1)
Ports 1, 2, 3
voltage
P71 to P73
0.3VDD
VDD
+0.7
2.5 to 5.5
0.9VDD
VDD
2.5 to 5.5
0.75VDD
VDD
4.0 to 5.5
VSS
2.5 to 4.0
VSS
4.0 to 5.5
VSS
2.5 to 4.0
VSS
2.5 to 5.5
VSS
V
0.1VDD
+0.4
P70 port input/
interrupt side
PWM0, PWM1
VIL(2)
VIL(3)
Port 0
Port 70 watchdog
timer side
VIL(4)
XT1, XT2, CF1, RES
0.2VDD
0.15VDD
+0.4
0.2VDD
0.8VDD
-1.0
2.5 to 5.5
VSS
0.25VDD
Instruction cycle
tCYC
4.0 to 5.5
0.294
200
time
(Note 2-2)
3.0 to 5.5
0.367
200
2.5 to 5.5
0.588
200
4.0 to 5.5
0.1
10
2.5 to 5.5
0.1
5
4.0 to 5.5
0.2
20.4
2.5 to 5.5
0.1
10
(Note 2-1)
External system
FEXCF
CF1
clock frequency
µs
• CF2 pin open
• System clock frequency
division ratio=1/1
• External system clock
duty=50±5%
• CF2 pin open
MHz
• System clock frequency
division ratio=1/2
Oscillation
FmCF(1)
CF1, CF2
frequency
range
10MHz ceramic oscillation
See Fig 1.
FmCF(2)
CF1, CF2
(Note 2-3)
8MHz ceramic oscillation
See Fig 1.
FmCF(3)
CF1, CF2
5MHz ceramic oscillation
See Fig 1.
FmRC
Internal RC oscillation
FmMRC
Frequency variable RC
oscillation source oscillation
FsX’tal
XT1, XT2
32.768kHz crystal oscillation
See Fig 2.
4.0 to 5.5
10
3.0 to 5.5
8
2.5 to 5.5
5
2.5 to 5.5
0.3
1.0
2.5 to 5.5
16
2.5 to 5.5
32.768
MHz
2.0
kHz
Note 2-1: VDD must be held greater than or equal to 3.0V in the flash ROM onboard programming mode.
Note 2-2: Relationship between tCYC and oscillation frequency is 3/FmCF at a division ratio of 1/1 and 6/FmCF at a
division ratio of 1/2.
Note 2-3: See Tables 1 and 2 for the oscillation constants.
No.8298-12/23
LC87F5G32A
Electrical Characteristics at Ta = -30°C to +70°C, VSS1 = VSS2 = VSS3 = 0V
Parameter
Symbol
Pin/Remarks
Specification
Conditions
VDD[V]
High level input
IIH(1)
current
Ports 0, 1, 2, 3
Output disabled
Port 7
RES
Pull-up resistor off
PWM0, PWM1
VIN=VDD
(Including output Tr's off
min
typ
max
unit
2.5 to 5.5
1
2.5 to 5.5
1
2.5 to 5.5
15
leakage current)
IIH(2)
XT1, XT2
For input port specification
VIN=VDD
Low level input
IIH(3)
CF1
VIN=VDD
IIL(1)
Ports 0, 1, 2, 3
Output disabled
Port 7
RES
Pull-up resistor off
current
PWM0, PWM1
VIN=VSS
(Including output Tr's off
2.5 to 5.5
-1
2.5 to 5.5
-1
µA
leakage current)
IIL(2)
XT1, XT2
For input port specification
VIN=VSS
IIL(3)
CF1
VIN=VSS
2.5 to 5.5
-15
High level output
VOH(1)
Ports 0, 1, 2, 3
IOH= -1mA
4.5 to 5.5
VDD-1
voltage
VOH(2)
IOH= -0.1mA
2.5 to 5.5
VDD-0.5
VOH(3)
P71 to P73
IOH= -0.4mA
4.5 to 5.5
VDD-1
VOH(4)
PWM0, PWM1,
IOH= -6mA
4.5 to 5.5
VDD-1
VOH(5)
P05(System clock
IOH= -1.6mA
4.5 to 5.5
VDD-0.4
2.5 to 5.5
VDD-0.4
output function
V
VOH(6)
used)
IOH= -1mA
Low level output
VOL(1)
Ports 0, 1, 2, 3,
IOL=10mA
4.5 to 5.5
1.5
voltage
VOL(2)
PWM0, PWM1,
IOL=1.6mA
4.5 to 5.5
0.4
IOL=1mA
VOL(3)
Pull-up resistance
XT2
2.5 to 5.5
0.4
VOL(4)
P00, P01
IOL=30mA
4.5 to 5.5
1.5
VOL(5)
Port 7
IOL=1mA
2.5 to 5.5
0.4
Rpu(1)
Ports 0, 1, 2, 3
VOH=0.9VDD
Port 7
Rpu(2)
Ports 0, 1, 2, 3
VOH=0.9VDD
Port 7
Hysteresis voltage
VHYS
RES
Ports 1, 2, 7
Pin capacitance
CP
All pins
4.5 to 5.5
15
35
80
2.5 to 4.5
18
50
150
kΩ
2.5 to 5.5
0.1VDD
V
2.5 to 5.5
10
pF
For pins other than that under
test: VIN=VSS
f=1MHz
Ta=25°C
No.8298-13/23
LC87F5G32A
Serial Input/Output Characteristics at Ta = -30°C to +70°C, VSS1 = VSS2 = VSS3 = 0V
1. SIO0 Serial I/O Characteristics (Note 4-1-1)
Parameter
Symbol
Pin/Remarks
Specification
Conditions
Input clock
VDD[V]
Frequency
tSCK(1)
Low level
tSCKL(1)
SCK0(P12)
See Fig. 6.
tSCKH(1)
2.5 to 5.5
pulse width
tSCKHA(1)
tCYC
4
• (Note 4-1-2)
Frequency
tSCK(2)
SCK0(P12)
• CMOS output selected
4/3
• See Fig. 6.
Output clock
Low level
tSCKL(2)
1/2
pulse width
High level
tSCK
tSCKH(2)
2.5 to 5.5
pulse width
tSCKHA(2)
1/2
• Continuous data
transmission/reception mode
tSCKH(2)
• CMOS output selected
+2tCYC
• See Fig. 6.
Data setup time
Serial input
unit
1
• Continuous data
transmission/reception mode
tsDI(1)
SB0(P11),
SI0(P11)
tSCKH(2)
+(10/3)
tCYC
tCYC
• Must be specified with
respect to rising edge of
2.5 to 5.5
0.03
2.5 to 5.5
0.03
SIOCLK.
Data hold time
Output clock
Input clock
Output delay
Serial output
max
1
• See Fig. 6.
Serial clock
typ
2
pulse width
High level
min
• See Fig. 6.
thDI(1)
tdD0(1)
time
SO0(P10),
SB0(P11)
• Continuous data
transmission/reception mode
2.5 to 5.5
• (Note 4-1-3)
tdD0(2)
• Synchronous 8-bit mode
• (Note 4-1-3)
tdD0(3)
2.5 to 5.5
(1/3)tCYC
+0.05
µs
1tCYC
+0.05
(Note 4-1-3)
2.5 to 5.5
(1/3)tCYC
+0.05
Note 4-1-1: These specifications are theoretical values. Add margin depending on its use.
Note 4-1-2: To use serial-clock-input in continuous trans/rec mode, a time from SI0RUN being set when serial clock is
"H" to the first negative edge of the serial clock must be longer than tSCKHA.
Note 4-1-3: Must be specified with respect to falling edge of SIOCLK. Must be specified as the time to the beginning of
output state change in open drain output mode. See Fig. 6.
No.8298-14/23
LC87F5G32A
2. SIO1 Serial I/O Characteristics (Note 4-2-1)
Parameter
Symbol
Pin/Remarks
Specification
Conditions
Input clock
Frequency
tSCK(3)
Low level
tSCKL(3)
SCK1(P15)
See Fig. 6.
2.5 to 5.5
pulse width
High level
Frequency
SCK1(P15)
• CMOS output selected
tSCKL(4)
2
1/2
tSCK
tSCKH(4)
1/2
pulse width
Serial input
Data setup time
tsDI(2)
SB1(P14),
SI1(P14)
• Must be specified with
respect to rising edge of
2.5 to 5.5
0.03
2.5 to 5.5
0.03
SIOCLK.
Data hold time
Output delay time
• See Fig. 6.
thDI(2)
tdD0(4)
SO1(P13),
SB1(P14)
Serial output
unit
1
2.5 to 5.5
pulse width
High level
max
1
• See Fig. 6.
Low level
typ
tCYC
tSCKH(3)
tSCK(4)
min
2
pulse width
Output clock
Serial clock
VDD[V]
• Must be specified with
µs
respect to falling edge of
SIOCLK.
• Must be specified as the
time to the beginning of
2.5 to 5.5
(1/3)tCYC
+0.05
output state change in
open drain output mode.
• See Fig. 6.
Note 4-2-1: These specifications are theoretical values. Add margin depending on its use.
No.8298-15/23
LC87F5G32A
Pulse Input Conditions at Ta = -30°C to +70°C, VSS1 = VSS2 = VSS3 = 0V
Parameter
Symbol
Pin/Remarks
Specification
Conditions
VDD[V]
High/low level
tPIH(1)
INT0(P70),
• Interrupt source flag can be set.
pulse width
tPIL(1)
INT1(P71),
• Event inputs for timer 0 or 1 are
INT2(P72),
enabled.
min
typ
2.5 to 5.5
1
2.5 to 5.5
2
2.5 to 5.5
64
2.5 to 5.5
256
2.5 to 5.5
200
max
unit
INT4(P20 to P23),
INT5(P24 to P27)
tPIH(2)
INT3(P73) when
• Interrupt source flag can be set.
tPIL(2)
noise filter time
• Event inputs for timer 0 are
constant is 1/1
tPIH(3)
INT3(P73) when
• Interrupt source flag can be set.
tPIL(3)
noise filter time
• Event inputs for timer 0 are
constant is 1/32
enabled.
tPIH(4)
INT3(P73) when
• Interrupt source flag can be set.
tPIL(4)
noise filter time
• Event inputs for timer 0 are
constant is 1/128
tPIL(5)
RES
tCYC
enabled.
enabled.
Resetting is enabled.
µs
AD Converter Characteristics at VSS1 = VSS2 = VSS3 = 0V
<12-bits AD Converter Mode / Ta= -10°C to +50°C>
Parameter
Symbol
Pin/Remarks
Specification
Conditions
VDD[V]
Resolution
N
AN0(P00) to
Absolute accuracy
ET
AN7(P07)
Conversion time
TCAD
AN8(P70)
AN9(P71)
AN10(XT1)
Analog input
VAIN
min
4.75 to 5.25
(Note 6-1)
typ
max
12
4.75 to 5.25
unit
bit
T.B.D
LSB
See conversion time calculation
formulas.
4.75 to 5.25
38.5
90
µs
4.75 to 5.25
VSS
VDD
V
(Note 6-2)
AN11(XT2)
voltage range
Analog port input
IAINH
VAIN=VDD
4.75 to 5.25
current
IAINL
VAIN=VSS
4.75 to 5.25
1
-1
µA
<8-bits AD Converter Mode / Ta= -30°C to +70°C>
Parameter
Symbol
Pin/Remarks
Specification
Conditions
VDD[V]
Resolution
N
AN0(P00) to
Absolute accuracy
ET
AN7(P07)
Conversion time
TCAD
AN8(P70)
AN9(P71)
AN10(XT1)
Analog input
VAIN
AN11(XT2)
min
3.0 to 5.5
typ
max
8
bit
±1.5
(Note 6-1)
3.0 to 5.5
See conversion time calculation
4.5 to 5.5
22.5
90
3.0 to 5.5
45
90
3.0 to 5.5
VSS
VDD
formulas.
(Note 6-2)
voltage range
Analog port input
IAINH
VAIN=VDD
3.0 to 5.5
current
IAINL
VAIN=VSS
3.0 to 5.5
1
-1
unit
LSB
µs
V
µA
Conversion time calculation formulas:
12-bits AD Converter Mode: TCAD (Conversion time) = ((52/(division ratio))+2) × (1/3) × tCYC
8-bits AD Converter Mode: TCAD (Conversion time) = ((32/(division ratio))+2) × (1/3) × tCYC
Note 6-1: The quantization error (±1/2LSB) must be excluded from the absolute accuracy. The absolute accuracy must
be measured in the microcontroller's state in which no I/O operations occur at the pins adjacent to the analog
input channel.
Note 6-2: The conversion time refers to the period from the time an instruction for starting a conversion process till the
time the conversion results register(s) are loaded with a complete digital conversion value corresponding to
the analog input value.
The conversion time is 2 times the normal-time conversion time when:
• The first AD conversion is performed in the 12-bit AD conversion mode after a system reset.
• The first AD conversion is performed after the AD conversion mode is switched from 8-bit to
12-bit conversion mode.
No.8298-16/23
LC87F5G32A
Consumption Current Characteristics at Ta = -30°C to +70°C, VSS1 = VSS2 = VSS3 = 0V
Parameter
Symbol
Pin/
Remarks
VDD[V]
consumption
VDD1
=VDD2
• FsX’tal=32.768kHz crystal oscillation mode
current
=VDD3
• System clock set to 10MHz side
Normal mode
IDDOP(1)
(Note 7-1)
Specification
Conditions
min
typ
Max
unit
• FmCF=10MHz ceramic oscillation mode
• Internal RC oscillation stopped
4.0 to 5.5
7.7
20
4.0 to 5.5
8.7
20
4.5 to 5.5
5.2
12
• Frequency variable RC oscillation stopped
• 1/1 frequency division ratio
IDDOP(2)
• CF1=20MHz external clock
• FsX’tal=32.768kHz crystal oscillation mode
• System clock set to CF1 side
• Internal RC oscillation stopped
• Frequency variable RC oscillation stopped
• 1/2 frequency division ratio
IDDOP(3)
• FmCF=5MHz ceramic oscillation mode
• FsX’tal=32.768kHz crystal oscillation mode
mA
• System clock set to 5MHz side
IDDOP(4)
• Internal RC oscillation stopped
• Frequency variable RC oscillation stopped
4.5 to 5.5
3.5
10
4.5 to 5.5
0.7
2.9
2.5 to 4.5
0.4
2.1
4.5 to 5.5
1.4
5.3
2.5 to 4.5
0.9
3.9
4.5 to 5.5
34
90
• 1/1 frequency division ratio
IDDOP(5)
• FmCF=0Hz (oscillation stopped)
• FsX’tal=32.768kHz crystal oscillation mode
IDDOP(6)
• System clock set to internal RC oscillation
• Frequency variable RC oscillation stopped
• 1/2 frequency division ratio
IDDOP(7)
• FmCF=0Hz (oscillation stopped)
• FsX’tal=32.768kHz crystal oscillation mode
• Internal RC oscillation stopped
IDDOP(8)
• System clock set to 1MHz with
frequency variable RC oscillation
• 1/2 frequency division ratio
IDDOP(9)
• FmCF=0Hz (oscillation stopped)
• FsX’tal=32.768kHz crystal oscillation mode
• System clock set to 32.768kHz side
IDDOP(10)
µA
• Internal RC oscillation stopped
• Frequency variable RC oscillation stopped
2.5 to 4.5
23
70
• 1/2 frequency division ratio
Note 7-1: The consumption current value includes none of the currents that flow into the output Tr and internal pull-up
resistors.
Continued on next page.
No.8298-17/23
LC87F5G32A
Continued from preceding page.
Parameter
HALT mode
Symbol
IDDHALT(1)
Pin/
VDD[V]
consumption
VDD1
=VDD2
• FmCF=10MHz ceramic oscillation mode
current
=VDD3
• FsX’tal=32.768kHz crystal oscillation mode
(Note 7-1)
Specification
Conditions
remarks
min
typ
max
unit
• HALT mode
• System clock set to 10MHz side
4.0 to 5.5
3.1
6
4.0 to 5.5
4
9
4.5 to 5.5
1.9
4.1
• Internal RC oscillation stopped
• Frequency variable RC oscillation stopped
• 1/1 frequency division ratio
IDDHALT(2)
• HALT mode
• CF1=20MHz external clock
• FsX’tal=32.768kHz crystal oscillation mode
• System clock set to CF1 side
• Internal RC oscillation stopped
• Frequency variable RC oscillation stopped
• 1/2 frequency division ratio
IDDHALT(3)
• HALT mode
• FmCF=5MHz ceramic oscillation mode
• FsX’tal=32.768kHz crystal oscillation mode
mA
• System clock set to 5MHz side
IDDHALT(4)
• Internal RC oscillation stopped
• Frequency variable RC oscillation stopped
2.5 to 4.5
1.3
3.0
4.5 to 5.5
0.35
1.4
2.5 to 4.5
0.25
0.95
4.5 to 5.5
1.1
4
2.5 to 4.5
0.8
3.0
4.5 to 5.5
20
51
2.5 to 4.5
18
35
4.5 to 5.5
0.04
11
2.5 to 4.5
0.01
8
4.5 to 5.5
17
50
2.5 to 4.5
12
30
• 1/1 frequency division ratio
IDDHALT(5)
• HALT mode
• FmCF=0Hz (oscillation stopped)
• FsX’tal=32.768kHz crystal oscillation mode
• System clock set to internal RC oscillation
IDDHALT(6)
• Frequency variable RC oscillation stopped
• 1/2 frequency division ratio
• HALT mode
IDDHALT(7)
• FmCF=0Hz (oscillation stopped)
• FsX’tal=32.768kHz crystal oscillation mode
• Internal RC oscillation stopped
IDDHALT(8)
• System clock set to 1MHz with
frequency variable RC oscillation
• 1/2 frequency division ratio
• HALT mode
IDDHALT(9)
• FmCF=0Hz (oscillation stopped)
• FsX’tal=32.768kHz crystal oscillation mode
• System clock set to 32.768kHz side
IDDHALT(10)
• Internal RC oscillation stopped
• Frequency variable RC oscillation stopped
• 1/2 frequency division ratio
HOLD mode
consumption
current
Timer HOLD mode
IDDHOLD(1)
IDDHOLD(3)
HOLD mode
(External clock mode)
VDD1
Timer HOLD mode
• CF1=VDD or open
IDDHOLD(4)
µA
• CF1=VDD or open
IDDHOLD(2)
consumption
current
VDD1
(External clock mode)
• FsX’tal=32.768kHz crystal oscillation mode
Note 7-1: The consumption current value includes none of the currents that flow into the output Tr and internal pull-up
resistors.
No.8298-18/23
LC87F5G32A
F-ROM Programming Characteristics at Ta = +10°C to +55°C, VSS1 = VSS2 = VSS3 = 0V
Parameter
Symbol
Pin/Remarks
Specification
Conditions
VDD[V]
Onboard
IDDFW
VDD1
programming
min
typ
max
unit
• 128-byte programming
• Erasing current included
3.0 to 5.5
25
40
mA
3.0 to 5.5
22.5
45
ms
current
Programming
tFW
• 128-byte programming
time
• Erasing current included
• Time for setting up 128-byte data
is excluded.
UART (Full duplex) Operating Conditions at Ta = -30°C to +70°C, VSS1 = VSS2 = VSS3 = 0V
Parameter
Symbol
Pin/Remarks
Specification
Conditions
VDD[V]
Transfer rate
UBR
P20, P21
2.5 to 5.5
min
typ
16/3
max
unit
8192/3
tCYC
Data length: 7, 8, and 9 bits (LSB first)
Stop bits:
1-bit (2-bit in continuous data transmission)
Parity bits: Non
Example of Continuous 8-bit Data Transmission Mode Processing (first transmit data=55H)
Start bit
Start of
transmission
Stop bit
End of
transmission
Transmit data (LSB first)
UBR
Example of Continuous 8-bit Data Reception Mode Processing (first receive data=55H)
Stop bit
Start bit
Receive data (LSB first)
Start of
reception
End of
reception
UBR
No.8298-19/23
LC87F5G32A
Characteristics of a Sample Main System Clock Oscillation Circuit
Given below are the characteristics of a sample main system clock oscillation circuit that are measured using a
SANYO-designated oscillation characteristics evaluation board and external components with circuit constant values
with which the oscillator vendor confirmed normal and stable oscillation.
Table 1 Characteristics of a Sample Main System Clock Oscillator Circuit with a Ceramic Oscillator
Nominal
Frequency
10MHz
8MHz
5MHz
Operating
Circuit Constant
Vendor Name
MURATA
MURATA
MURATA
Oscillator Name
Oscillation Stabilization
Voltage
Time
Remarks
C1
C2
Rf
Rd1
Range
typ
max
[pF]
[pF]
[Ω]
[Ω]
[V]
[ms]
[ms]
CSTCE10M0G52-R0
(10)
(10)
Open
680
4.0 to 5.5
0.1
0.5
CSTCE10M0G52-B0
(10)
(10)
Open
680
4.0 to 5.5
0.1
0.5
(SMD type)
CSTCE8M00G52-R0
(10)
(10)
Open
1.0k
3.0 to 5.5
0.1
0.5
Internal C1, C2
CSTCE8M00G52-B0
(10)
(10)
Open
1.0k
3.0 to 5.5
0.1
0.5
(SMD type)
Internal C1, C2
CSTCR5M00G53-R0
(15)
(15)
Open
2.2k
2.5 to 5.5
0.2
0.6
Internal C1, C2
CSTCR5M00G53-B0
(15)
(15)
Open
2.2k
2.5 to 5.5
0.2
0.6
(SMD type)
The oscillation stabilization time refers to the time interval that is required for the oscillation to get stabilized after VDD
goes above the operating voltage lower limit (see Figure 4).
It is recommended to insert feedback resister(Rf:1MΩ) when power supply voltage is used around 2.5V.
Characteristics of a Sample Subsystem Clock Oscillator Circuit
Given below are the characteristics of a sample subsystem clock oscillation circuit that are measured using a SANYOdesignated oscillation characteristics evaluation board and external components with circuit constant values with which
the oscillator vendor confirmed normal and stable oscillation.
Table 2 Characteristics of a Sample Subsystem Clock Oscillator Circuit with a Crystal Oscillator
Nominal
Frequency
Operating
Circuit Constant
Vendor Name
Oscillator Name
EPSON
32.768kHz
Time
C3
C4
Rf
Rd2
Range
typ
max
[pF]
[pF]
[Ω]
[Ω]
[V]
[s]
[s]
18
18
Open
510k
2.5 to 5.5
1.1
3.0
MC-306
TOYOCOM
Oscillation Stabilization
Voltage
Remarks
Applicable CL
value=12.5pF
The oscillation stabilization time refers to the time interval that is required for the oscillation to get stabilized after the
instruction for starting the subclock oscillation circuit is executed and to the time interval that is required for the
oscillation to get stabilized after the HOLD mode is reset (see Figure 4).
Note: The components that are involved in oscillation should be placed as close to the IC and to one another as possible
because they are vulnerable to the influences of the circuit pattern.
CF2
CF1
Rf
XT1
XT2
Rf
Rd1
C1
C2
C3
Rd2
C4
CF
X’tal
Figure 1 CF Oscillator Circuit
Figure 2 XT Oscillator Circuit
0.5VDD
Figure 3 AC Timing Measurement Point
No.8298-20/23
LC87F5G32A
VDD
Operating VDD
lower limit
0V
Power Supply
Reset time
RES
Internal RC
oscillation
tmsCF
CF1, CF2
tmsX’tal
XT1, XT2
Operating mode
Unpredictable
Reset
Instruction execution
Reset Time and Oscillation Stabilization Time
HOLD reset signal
HOLD reset signal
absent
HOLD release signal VALID
Internal RC
oscillation
tmsCF
CF1, CF2
tmsX’tal
XT1, XT2
State
HOLD
HALT
HOLD Reset Signal and Oscillation Stabilization Time
Figure 4 Oscillation Stabilization Times
No.8298-21/23
LC87F5G32A
VDD
(Note)
Determine the value of CRES and RRES so that the reset
signal is present for a period of 200µs after the supply
voltage goes beyond the lower limit of the IC's operating
voltage.
RRES
RES
CRES
Figure 5 Reset Circuit
SIOCLK :
DATAIN :
DI0
DI1
DI2
DI3
DI4
DI5
DI6
DATAOUT :
DO0
DO1
DO2
DO3
DO4
DO5
DO6
DI7
DI8
DO7
DO8
Data RAM
transfer period
(SIO0 only)
tSCK
tSCKH
tSCKL
SIOCLK :
tsDI
thDI
DATAIN :
tdDO
DATAOUT :
Data RAM
transfer period
(SIO0 only)
tSCKL
tSCKHA
SIOCLK :
tsDI
thDI
DATAIN :
tdDO
DATAOUT :
Figure 6 Serial I/O Output Waveforms
tPIL
tPIH
Figure 7 Pulse Input Timing Signal Waveform
No.8298-22/23
LC87F5G32A
SANYO Semiconductor Co.,Ltd. assumes no responsibility for equipment failures that result from using
products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition
ranges, or other parameters) listed in products specifications of any and all SANYO Semiconductor Co.,Ltd.
products described or contained herein.
SANYO Semiconductor Co.,Ltd. strives to supply high-quality high-reliability products, however, any and all
semiconductor products fail or malfunction with some probability. It is possible that these probabilistic failures or
malfunction could give rise to accidents or events that could endanger human lives, trouble that could give rise
to smoke or fire, or accidents that could cause damage to other property. When designing equipment, adopt
safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not
limited to protective circuits and error prevention circuits for safe design, redundant design, and structural
design.
In the event that any or all SANYO Semiconductor Co.,Ltd. products described or contained herein are
controlled under any of applicable local export control laws and regulations, such products may require the
export license from the authorities concerned in accordance with the above law.
No part of this publication may be reproduced or transmitted in any form or by any means, electronic or
mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise,
without the prior written consent of SANYO Semiconductor Co.,Ltd.
Any and all information described or contained herein are subject to change without notice due to
product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the
SANYO Semiconductor Co.,Ltd. product that you intend to use.
Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed
for volume production.
Upon using the technical information or products described herein, neither warranty nor license shall be granted
with regard to intellectual property rights or any other rights of SANYO Semiconductor Co.,Ltd. or any third
party. SANYO Semiconductor Co.,Ltd. shall not be liable for any claim or suits with regard to a third party's
intellctual property rights which has resulted from the use of the technical information and products mentioned
above.
This catalog provides information as of January, 2007. Specifications and information herein are subject
to change without notice.
PS No.8298-23/23